Search Documents

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By R. L. Crosby, L. W. Higley

Magnesium- rich magnesium- aluminum- zirconium alloys in the cast and in the extruded and heat- treated condition were studied to identify the phases present and to determine phase distribution . In cast alloys , two intermetallic compounds were identified : ZrAla by X- ray diffraction ; and Mg₁ Al₁₂ by microscopical observation . Based on microscopical comparisons between the known phases in the cast structures and the phases in the structures of extruded and heat - treated rods , ZrAl₂ and Mg1 , Al12 were identified in the structure of the latter . The presence of these intermetallic compounds in rod specimens could not be confirmed by X- ray diffraction . ZrAl₂ was observed in the structure of extruded and heat - treated rod specimens containing as little as 0.01 weight - percent zirconium . The presence of aluminum restricts the solubility of zirconium in magnesium because of the strong tendency to form ZrAla . This intermetallic compound segregated in clusters of small particles in the matrix of cast alloys , and only slight improvement in distribution was noted when the alloying techniques were varied .

Jan 1, 1964

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By Michael G. Zabetakis

The autoignition temperatures (A.I.T.'s) of natural and synthetic lubricants in air were generally found to decrease with increasing pressure. Of the two types of fluids, synthetic and natural, studied in some detail, the phosphate esters had higher A.I.T.'s at any pressure between 1 and 200 atmospheres than the mineral oils. Most of the A.I.T. data obtained in this study obeyed the relationship predicted by Semenov's theory of ignition.

Jan 1, 1962

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By J. R. Thoenen

During 1928 questionnaires covering the calendar year 1927 were sent to over 1700 quarries: producing stone for purposes other thaw cutting to dimension. These inclined producers of stone for limn burning; cement manufacture, rip rag, and crushed stone. The various rinds of stone represented were limestone, trap rock, sandstone, granite, and marble. Replies received from limestone producers prior to November, 1928, were compiled into tables and published in February, 1925, as a preliminary report (Bureau of Mines Report of Investigation 2911).

Jan 1, 1930

By P. G. Bennett

The Bureau of Mines developed a process using ion exchange to recover cobalt from spent copper leach solutions. A preliminary economic evaluation of the process indicated that about one-third of the capital cost was attributed to the total resin inventory, and one-third of the operating cost was required for reagents to remove iron from the ion-exchange eluates. An agitated Pachuca elution system was investigated in place of a fixed-bed elution system. The Pachuca system reduced the resin inventory by 27 pet when compared with the fixed-bed elution system. Processing fresh spent copper leach solution reduced the resin inventory by 20 pct and resin iron loading by 80 pct. Reagent requirements for removing iron from the eluates were decreased because less iron was extracted. The Pachuca system, along with processing fresh spent copper leach solution, reduced the total resin inventory by 47 pct. A revised cost evaluation of the cobalt recovery process was obtained to determine the effects of these process modifIcations. The estimated total capital cost for a plant processing 10,000 gpm of spent copper leach solution containing 26 ppm Co was $23.1 million. With credits for nickel, zinc, and copper byproducts, the estimated net operating cost was $5.10/lb of cobalt.

Jan 1, 1988

By R. S. Dean

The original flotation reagents were certain oils selected for a combination of properties that occurred fortuitously. It was recognized quite early in the study of flotation mechanism that, in order to function, an oil must have an active group-one that differs from the remainder of the molecule in its affinity for water or the mineral particle. Wark4 gives credit for recognition of this elementary chemical principle to the senior author of this report.5 However, it was soon found that simple hydrocarbons could not be used as flotation reagents and that two of the functions, which were combined in the early flotation oils such as pine and eucalyptus, could be obtained in separate compounds and their relative intensity controlled to advantage. These two functions were called collecting and frothing.

Jan 1, 1944

By C. F. Jackson

This paper describing the mining practices at a mine in the Southeast Missouri district is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The conditions, operating methods, and practice described in the following pages arc those obtaining at a property in the Southeastern Missouri lead belt, St. Francois County, Mo. This property is the eldest in the county and is a consolidation of a number of separate mines originally opened up as individual operations many years ago. Present-day operations have necessarily to be adapted to suit the older levels, stones, and pillars, and also the recovery of ore from worked over areas which was considered too low grade to mine in the earlier days constitutes a different problem than that of development and mining in virgin ground.

Jan 1, 1929

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By E. C. Baker

Costs of disposing of steel slag are estimated based on the present method and a proposed alternate method for a steel mill in the Pittsburgh area. Estimated cost data were calculated by the Bureau of Mines and do not reflect the investment and operating costs and credits of a specific steel mill and processing plant. The alternate method of steel slag disposal would result in an appreciable cost savings to the mill and concurrently supply the industrial and commercial markets with low-cost, high-quality construction materials.

Jan 1, 1970

By Ott F. Heizer

This paper describing the practice at the tungsten concentrator of the Nevada-Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on milling practices, methods, and costs in the United States. The ore, which contains about 1.10 per cent of scheelite (CaW04), is concentrated on tables and by means of a magnetic separator and roasters. A product containing 70.43 tungsten trioxide is shipped. The plant was designed for a capacity of 100 tons per 24 hours, but at present 142 tons of ore are milled per day. The author acknowledges the assistance of William O. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in preparing this paper.

Jan 1, 1930

By H. H. Schrenk

[There is a need for method of determining: benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the modification of the Elliott and Dalton6/ procedure. This depends on the nitration of the benzene to reduction to phenylenediamine with all excesses of standard titanous chloride; solution, and titration with e standard ferric ammonium sulphite solution. This method has the disadvantages of being what time consulting: and cumbersome it requires considerable apparatus, and a special modification is necessary in the presence of toluene.]

Jan 1, 1935

By G. H. Keith

The Bureau of Mines determined the mechanism(s) involved in observed anomalous changes in mechanical properties of vanadium-base alloys. Tensile properties of electrorefined and commercial-purity vanadium-base alloys containing up to 5 atomic percent molybdenum or titanium were measured between 77° and 673° K. Snoek oxygen and nitrogen peak heights were measured to determine the changes in dissolved interstitial content caused by increasing quantities of solute. In addition, changes in lattice parameter were followed wit: precision X-ray techniques. Softening, observed in alloys containing titanium, is explained by the formation of a second-phase titanium compound with oxygen or nitrogen. However, because of partitioning of titanium between compound formation and solid solution formation, about five times the stoichiometric amount was required for complete reaction. Addition of 1 percent titanium drastically lowered the strengthening due to strain aging, at 673° K, and 2 percent titanium essentially eliminated it. All alloys were ductile at 77° K. Variations in the tensile properties of the molybdenum-containing alloys are explained by variations in the amounts of interstitial impurities present. The molybdenum did not react with these impurities and had no effect on strengthening due to strain aging. Commercial-purity vanadium alloys containing more than 2 percent molybdenum were brittle at 77° K.

Jan 1, 1969

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935

By D. I. Bleiwas

Bureau of Mines personnel evaluated the potential availability of nickel from 151 deposits in 18 market economy countries and selected 126 for detailed analyses. An evaluation was made of tonnage-cost relationships indicating the quantity of nickel available at various total costs of production expressed in dollars per pound nickel, including a 15-pct rate of return on the invested capital. The 126 deposits studied contain approximately 73 million metric tons (t) of nickel. An estimated 52 million t is available from laterite deposits, of which less than 2 pct could be produced at $3.50/lb Ni, about equal to the average published price of nickel in 1981. Approximately 21 million t of nickel is available from sulfide deposits, of which about 10.0 million t can be produced at $3.50/lb. Sensitivity studies performed for both laterite deposits and sulfide deposits indicate that the total cost of nickel from laterites is most sensitive to increases in energy costs, and that sulfides are most sensitive to increases in labor costs; sulfides are also sensitive to changes in byproduct revenues. In 1983 the Nickel Mountain mine in Oregon was the only U.S. producer, though development continued on the Gasquet property in California. Of the total 5.1 million t of recoverable nickel in the United States, about 20 pct is available at or below $3.50/lb.

Jan 1, 1984

By George H. Holmes

This paper is one of a series on mining methods and practices published by the Bureau of Mines. It describes quarrying methods and crushing practices of the U. S. Lime. Products Corp. at its Sloan and Apex quarries. Calcining and milling processes. at the Sloan and Henderson plants also are outlined. The Sloan dolomite and limestone quarries and plant are in secs. 12 and 13, T. 23 5., R. 60 E., and sec. 18, T. 23 S., R. 61 E., M.D.B. &M., Clark County, Nev., about. 17 miles by paved highway southwest of Las Vegas (fig. 1). The Apox limestone quarry, and crushing plant are in sec. 26, T. 18 S., R. 63 E., M.D.B.&M., Clark County, Nov., approximately 18 milos northeast of Las Vegas, adjacent to U. S. Highway 91 (fig. 1). The Henderson calcining plant is Inc., in sec. 13, T. 22 S., R. 62 E., 14 miles southeast of Las Vegas on U. in a reduction unit of Basic Magnesium, M.D.B. &M., Clark County, Nev., about S. Highway 93 (fig. 1).

Sep 1, 1949

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By Victor E. Kral

"SUMMARYA preliminary examination of the Buena Vista iron deposit was made in June 1942 by Paul E. Pesonen, mining engineer of the Bureau of Mines. Subsequent examinations were made by D. W. Butner, of the Bureau, in March 1943, and by the author in July 1944, who recommended exploration by diamond drilling, trenching, and sampling. Work on the project was done during the period March 28 to May 26, 1945.Property holdings, comprising 16 claims known as the Buena Vista group, are situated in sec. 4, T. 24 N., R. 34 E., Mount Diablo base and meridian, north Churchill County, about 37 miles east of Lovelock, Nev.Three diamond-drill holes totaling 575 feet were drilled; 45 small pits and ten trenches, totaling 435 linear feet, were excavated, and 84 channel samples totaling 862 feet were obtained under supervision of the Bureau.Purpose of the project was to determine the possible downward extension of the mineralized sections exposed in the outcrops and to determine grade of the ore.Bureau work was confined to one claim only - the Iron Mountain."

Jun 1, 1947