Search Documents

By Jr. Blake

This work was done to determine the technical feasibility of using the Pedersen process to produce cell-grade alumina and an iron byproduct from the high-silica and titania bauxites of the Pacific Northwest. Smelting of these bauxites with lime and coke at about 1,750° C in an electric arc furnace produced calcium aluminate slags in which at least 80 percent of the alumina was leachable by sodium carbonate solution. After a lime-desilication of the sodium aluminate leach liquors, neutralization of these solutions with carbon dioxide resulted in precipitation of an alumina hydrate of sufficient purity for calcination to cell-grade alumina. Recoveries of byproduct iron averaged over 90 percent; however, the iron contained about 1 percent phosphorous and would require additional refining. Additional small scale tests on these slags showed the following: (1) Titania had little effect on leachability if sufficient additional lime was added to form calcium titanate (CaO.TiO 2); (2) a slag containing about 14 percent silica required a slower cooling rate than one containing 7 percent silica for formation of high percentages of soluble aluminates; and (3) high-silica slags leached better at room temperature for long periods than at 65° C for shorter periods, but low-silica slags leached well by either method.

Jan 1, 1967

By JOE SIERAKOSKI, W. R. Hardwick

This paper , which describes mining methods and practices at the Johnson Camp copper -zinc mine , Coronado Copper & Zinc Co. , Cochise County , Ariz . , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . Johnson Camp is in the eastern foothills of the Little Dragoon Mountains in secs . 23 , 24 , 25 , and 26 , T. 15 S. , R. 22 E. ( fig . 1 ) . The mining property is in the low, rolling foothills at an altitude of slightly over 5,000 feet above sea level ( fig . 2 ) . The area is covered with scattered grass and small desert shrubs . The climate is mild , with hot summers and mild winters . The average annual precipitation is about 12 inches . The nearest surface water is the San Pedro River , some 12 miles west of the mine . The property is owned by the Coronado Copper & Zinc Co. , Los Angeles , Calif . This report gives a brief history of the property , describes the general geology of the area and of the ore deposits , outlines the methods of prospecting and exploration , and gives the methods of sampling and of estimating ore reserves . Development and stoping methods are explained . Underground transportation , ventilation , mine drainage , and safety measures also are described . The last section gives a brief description of the milling practice .

Jun 1, 1957

By M. L. Wouden

In the late 1970's, the Bureau of Mines began to examine the criteria for reestablishing vegetative cover on coal strip mine spoils near Glenrock, WY. A 9-acre plot, consisting of (1) spoils covered with topsoil, (2) spoils without topsoil, and (3) spoils treated with sewage sludge, was constructed. These plots were seeded with Tegmar intermediate wheatgrass (Agropyron intermedium), Fairway crested wheatgrass (A. cristatum), and Critana thickspike wheatgrass (A. dasystachyum). After 5 yr, the topsoil had about 70 pct plant coverage. Revegetated spoils, without topsoil addition, averaged approximately 30 pct plant coverage, and sewage sludge-treated spoils had about 45 pct plant coverage. Comparison of grass types showed the intermediate wheatgrass produced greater surface coverage.

Jan 1, 1986

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By L. C. George

The Bureau of Mines measured vapor pressures of selected mixtures in the binary system SnCla-ZnC12 by the static pressure method. Equations expressing the vapor pressure) and the heat and free energy of vaporization) as functions of temperature were developed by numerical analysis based on the sigma-plot method. It was found that the vapor pressure of any SnCl2-ZnCl2 mixture) at any temperature within the range of this investigation) could be accurately calculated from the derived values for the heat and free energy of vaporization for the mixture, with a probable error of 0.01 cm Hg or less.

Jan 1, 1967

By J. P. McGee

A 1,000-hour test with a gas turbine at 1,200° F showed a working fluid of 1 gr of ash per 100 scf of power gas (79 percent of the ash 7 to 35 microns in diameter) to be excessive for acceptable blade wear for commercial practicability. Blades in the turbine consisted of about 20 percent each of chromium, cobalt, and nickel; 3 percent molybdenum; 2-1/2 percent tungsten; and smaller amounts of manganese, columbium, and tantalum. Erosion of both the fronts and backs of the turbine nozzles was particularly heavy, the trailing edges being worn to a featheredge. Erosion of the buckets was less marked, although the leading edges were somewhat pitted. A refractory-lined combustor performed efficiently and with little abrasion of the lining by the ash-laden gas.

Jan 1, 1969

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By D. P. Schlick

The German experience in dealing with the health hazard of respirable dust in underground mines is reported from first-hand observation in this Bureau of Mines paper. The report covers-- 1. The control of dust by water infusion, water spraying, and ventilation. 2. The sampling devices (tyndalloscope , konimeter , and BAT-I) and methods used to determine the dust concentrations in mines. 3. The systems of classifying hazardous and safe dust levels in mines. 4. The research facilities devoted to theoretical and applied work on mine dust and pneumoconiotic disease. Tile major research projects on dust and disease now underway in West Germany are outlined in an appendix.

Jan 1, 1970

By P. D. Laverty

This report describes a processing method developed by the U.S. Bureau of Mines to produce high-quality flake graphite from the steelmaking waste known as kish. The kish produced by current steelmaking practices is a mixture of graphite, desulfurization slag, and iron that is skimmed from the molten iron feed to the basic oxygen furnace. It is estimated that the graphite content of kish discarded by U.S. steel plants is more than sufficient to meet the total U.S. demand for flake graphite. That need is now filled by natural graphite from foreign sources. Kish was treated by a combination of screening and hydraulic classification to produce a concentrate containing greater than 70 pct graphite. Leaching of the concentrate with hydrochloric acid solution gave a graphite product with 95-pct purity. An optional secondary leaching operation with hydrofluoric acid produced graphite with a purity of 98 pet or greater. The flake size of graphite from kish ranged from 10 mesh down. Evaluation of test samples by industrial graphite users indicated that kish graphite is a suitable substitute for the natural material for most uses. A process flowsheet and material balance for pilot plant design are presented.

Jan 1, 2010

By Eugene H. Skinner

The U.S. Bureau of Mines conducted experiments on the use of lightweight concrete in the density range of 100 Ib/ft3 for liners in underground mines. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a second section constructed in a drift using an air-supported formwork. The lightweight concrete in the two underground test sections was placed using piston pumps and a slickline. Fiber reinforcement was added to the concrete in the mine sections without any apparent problems with either pumping or placement of the concrete. In another experiment, the Bureau and Hecla Mining Co., Mullan, rD, used lightweight concrete in the density range of 25 Iblfe to replace timber blocking in a raise preparation structure. Other experiments are described in which low-density, lightweight concrete blocks were produced for mine ventilation doors, stoppings, and barricades. Other mine uses reviewed include pillars and collapsing beams. An advantage of low-density concrete is that it will display up to 50% deformation at a constant yield stress. These hlllovative concepts in deformable concrete lining systems will aid mine operators by decreasing capital and maintenance costs, increasing the available space in underground haulageways, and providing productivity gains and improved resource recovery in the soft, caving, squeezing, or bursting grollnu conditions often found in deep mines.

Jan 1, 1989

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

By Francis C. Lincoln

"INTRODUCTION As part of a general investigation of the zinc-producing area of southwestern Wisconsin, the Bureau of Mines undertook a limited amount of exploratory drilling in the immediate vicinity of the New Dale Rundell mine, in the Mifflin District of Iowa County, Wisc.The work was carried out during the early part of 1945, at a time when all effort was being directed toward increasing production of metals important to the Nation's war program. Bureau of Mines engineers decided to conduct exploration at the New Dale Rundell mine after a preliminary study of available data showed a reasonable possibility of indicating an important deposit. Before the Bureau of Mines investigation, 50 holes had been drilled in the vicinity. Of this number, 18 encountered ore of minable grade. Subsequently the mine was developed and operated for a brief period; however, work was stopped before all of the ore disclosed by drilling had been mined. There appeared to be a correlation between the ore shown by the drilling in the New Dale Rundell mine and another disclosure some 1,500 feet to the northwest. The Bureau of Mines exploration was pinned to explore this possible correlation. Of the 7 holes drilled by the Bureau of Mines, 3 disclosed minable ore beyond the limits of previous drilling."

Aug 1, 1946

By R. Hogg, Y. Lee, D. E. Rannels

"Lee, Yu-Chen, Richard Hogg, and D. Eugene Rannels. Extracellular matrix synthesis by coal dust-exposed type II epithelial cells. Am. J. Physiol. 267 (Lung Cell. Mol. Physiol. 11): L365–L374, 1994.—Although integrity of the alveolar basement membrane may influence progression of lung injury induced by inhaled particulates, little is known about direct effects of coal dusts on the alveolar epithelium or its extracellu¬lar matrix (ECM). Effects of dust on synthesis of cell and ECM proteins by type II cells (T2P) was thus investigated. Three coal dusts (anthracite no. 867; bituminous no. 1451 and no. 1361) and mine dust MIT-3, of respirable size, were studied as a function of dose and time over 3 days of primary T2P culture. On day 1, 750 µg/ml of 867 were required to increase relative synthesis of ECM proteins (ECM/cell). MIT-3, 1451, and 1361 were without effect. By day 3, 867 or MIT-3 increased ECM/ cell 60-100% at 300 µg/ml; 1451 produced modest, dose-dependent stimulation, whereas 1361 remained without effect. None of the dusts caused significant cytotoxicity. The results show dose- and time-dependent effects of well-characterized coal and mine dusts to modify partitioning of newly synthesized proteins into the ECM and suggest that coal dust exposure may modulate structure or function of the subepithelial basement membrane.basement membrane; cell culture; inorganic dust; lung injury; extracellular matrix deposition; pulmonary epitheliumCHRONIC EXPOSURE to coal dust may be associated with development of pulmonary fibrosis and consequent loss of normal lung function (see Ref. 26 for review). Al¬though the pathways of inorganic dust-induced lung injury are recognized to involve an inflammatory re¬sponse, the underlying pathogenic mechanisms are not understood in detail. Acute and chronic responses to dust exposure involve a variety of interacting cells of the immune system, including macrophages, T cells, and B cells, along with pulmonary fibroblasts. These responses reflect direct effects of the dust particles, as well as indirect effects mediated by soluble factors, including cytokines and eicosanoids (see Ref. 41 for review).Studies of pulmonary macrophages and fibroblasts following silica exposure suggest that dust-induced damage at the airway surface may involve cellular injury through oxidant-mediated pathways. Coal dusts and related inorganic particulates can activate the alveolar macrophage (42) to produce fibronectin (15) and cytokines, such as interleukin-1 or tumor necrosis factor (4) and/or other soluble products which act locally (29) to cause acute cellular injury and to initiate the progression of fibrotic lung damage (16). Type I epithelial cells are typically more susceptible than type II cells to oxidant injury. Type I cell damage and subsequent death leads to denudation of the subepithelial basement membrane (2, 21) and can be associated with leakage of plasma constituents from the pulmonary vasculature into the alveolar compartment (13)."

Dec 1, 1995

By F. D. Stevenson

Thermodynamic properties of metal halides and, in particular, vapor pressures have become of great importance in recent years owing to increased application of chemical processing to extraction of metals from their ores. Vapor pressure data serve not only as a valuable source of latent heat of vaporization and fusion values but also differences in metal-halide vapor pressures often provide the basis for their separation by conventional mass transfer operations. This literature search was made to provide a ready reference to experimental vapor-pressure data of metal halides and oxyhalides. Results are reported in two main sections: (1) A tabulation of vapor- pressure references for each of the metal halides (listed by metal) for which actual experimental data are reported (table 1), and (2) a bibliography of the citations. Metal halides and oxyhalides are listed by chemical formula and chemical name, based on the stock4 system. To facilitate location of the references, a listing of the journal titles and their abbreviations follows the bibliography.

Jan 1, 1963

By R. E. Morgan

Two sizes of Pennsylvania anthracite were gasified in the new-type Lurgi pressure generator at the Dorsten, Germany, works of the Steinkohlengas, A. G. These tests demonstrated that Chestnut-size anthracite and a Rice-Buckwheat mixture containing 27 and 19 percent ash, respectively, could be gasified satisfactorily at an elevated pressure in a fixed bed with oxygen and steam. These coals were especially prepared to approximate a rough-cleaned coal and a washed and screened product. The operating data obtained from the two tests and materials requirements are summarized. A wide range of reactant ratios could not be tested, nor could optimum operating conditions be determined, as the generator was being used throughout the testing program, employing normal operating practices, to produce gas for the gas grid; and the most economical coal, steam, and oxygen ratios may not have been used. Comparative costs are presented of the raw materials required for producing a high-B.t.u. gas, based on the operational data obtained from these tests and, to some extent, on data extrapolated from laboratory experimentation. A flowsheet of a proposed process for producing a high-B.t.u. gas by Lurgi gasification, followed by methanation, is also included.

Jan 1, 1958

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By R. S. Fowkes

A study was made by the Bureau of Mines of the penetration of selected granular materials in an unconfined state by wedge-shaped tools having dimensions comparable with the dimensions of the particles composing the materials. The output force for larger particles fluctuated radically. A custom-designed integrator was used to obtain work as a function of depth of penetration in the form of smooth curves. The influence of wedge angle, depth of penetration, penetration rate, entry angle, compaction state, and particle size on the force required and the work performed was ascertained. Empirical equations describing force and work as a function of penetration were obtained for each set of experiments.

Jan 1, 1973

By D. Harrington

Although for many years considerable attention has been given to devising safe and efficient methods of using explosives, with some success, relatively little has been done to provide satisfactory storage facilities for them. This was known long before the present war began, but it was emphasized during the past 30 months? inspections of explosive magazines by employees of the Bureau of Mines in administration of the Federal Explosives Act of December 26, 1941. These inspections have revealed woeful in adequacy as well as definite hazards and the urgent need for obtaining better storage facilities either by remodeling old magazines or constructing ink new ones that would afford suitable protection for the contents against theft, fire, deterioration, and detonation. The purpose of this paper is to offer suggestions and to show by sketches and drawings some of the fundamental features of suitable magazines. Type of construction and available materials differ with different; localities, but the information herein contained can be applied to most magazines, whether already constructed or the construct: on of which is planned. It is hoped that this information will be helpful and will aid persons who are trying to provide suitable storage for explosives end detonators. It is also hoped that States and cities will be made aware of the unbelievable laxity practiced in storing explosives in the United States and will take some remedial action.

Jan 1, 1945

By Curtis D. Edgerton

The Pittsburgh Mine Map Repository of the Bureau of Mines serves as a basic reference file for the archival preservation of mine map data of mines east of the Mississippi River. About 22,000 of an estimated 500,000 available mine maps have been microfilmed A computerized index serves as the mechanism for retrieval of any microfilmed mine map. The operation, equipment, and index are described in the report.

Jan 1, 1974