Search Documents

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system or systems, thus disclosed. Of the several systems initially investigated and evaluated, four Showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

This section of Minerals and Materials analyzes the following three factors affecting the recent performance of the U.S. and world mineral industries: 1) the health of the U.S. and world economies, 2) the level of interest rates and 3) the performance of productivity in both the U.S. mineral industry and the general economy. While these indicators do not exhaust the possible critical factors, they represent an initial attempt to probe some of the considerations underlying the performance of the U.S. minerals and materials industry. The U.S. and World Economies It is essential to analyze the state of the U.S. and world economy because the demand for minerals and materials is a derived demand; that is, since minerals and materials are used in the productive process, the demand for them is a direct function of the demand for the finished products of which they are a basic input. Thus, the demand for minerals and materials is directly affected by changes in present and planned consumption and investment expenditures. The past two issues of this publication have highlighted the generally discouraging performance of the national and inter-national economies. Briefly, the world economy is in the third year of the first long recession in recent history where inflation rates have remained above 5 percent. With many countries either unable or unwilling to support domestic spending while inflation continues, there has been a growing tendency to institute trade-restrictive policies to support domestic demand. The resulting weakened demand conditions in exporting nations have had a direct effect on the mineral industry.

Jan 1, 1982

By K. Biswas, S. Iverson, S. J. Jung

Computer modeling of rock flow in ore passes is being investigated and compared using MSC Soft-ware’s Working Model 2D1 (WM2D) and Itasca Corp.’s Particle Flow Code in Two Dimensions (PFC2D). This work is being carried out by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health to determine the usefulness of computer modeling to improve ore pass design. The types of tests included pendulum tests to validate WM2D simulations and simulated single-rock drop tests in both WM2D and PFC2D to understand their contact models. Simulated rock impacts at the ore pass chute and the use of inclined ore passes and doglegs were investigated in both programs. A PFC2D simulation showed that dynamic loads at the chute gate were reduced significantly when a dogleg transition was used, and simulations in which the ore pass was inclined showed significant reductions in chute impact loads compared to simulations of a vertical ore pass. A released hang-up was simulated using PFC2D.

By M. D. Heresy, H. F. Coward

"Whenever a manometer has been used for recording explosion pressures it has been calibrated under a series of static pressures. Whether the readings taken during the rapidly changing pressures of an explosion (dynamic pressures) truly represent the actual pressures therefore is an open question. The authors had hoped to solve this problem by conducting the calibration with the aid of known pressures, applied at about the ammo rate as in an explosion, for example, by means of a cylinder and piston, the piston being driven in by an eccentric cam at a rate which would be determined accurately by the shape and rate of revolution of the cam. If the rate of compression were great enough, then the pressure in the cylinder (to which the manometer is attached) could be calculated from the laws of adiabatic changes of pressure and volume. It seems highly probably, however, from H. T. Tizard's observations on pressure changes in a cylinder during rapid compression (55) 4/ that there is much heat loss, therefore pressure loss, in the very small interval of time during compression; although Tizard was able to estimate the amount thereof, he did so only by relying on his nanometer, which is exactly the procedure that the authors challenge on the grounds that the manometer was not standardized under the conditions of its use. Hence the authors were driven from this scheme of calibration to another, namely, comparing records of ono and the same explosion taken simultaneously on several instruments of as varied a type as possible. If 2 of a number of instruments agree, perhaps both are accurate; if 3 agree, probably each of the 3 is accurate; if 4 agree, it is almost certain each of the 4 is accurate.There was a second objective in the present work. If the Bureau of Mines and the B.C.D. (British Coal Dust) manometers differ in their records, then from a sufficiently comprehensive series of experiments it may be possible to coordinate the extensive results already obtained at the American and British stations.Thirdly, it was hoped to learn which is the best available instrument for observing the pressures of coal-dust and as explosions and, if possible, to indicate means for improvement in manometry."

May 1, 1935

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By W. T. Wertman

LABORATORY research has been started at the Bureau of Mines Morgantown Petroleum Research Laboratory, Morgantown, Va., to investigate the possibilities thermal-recovery methods for producing crude oils of high API gravity found in oil reservoirs of the eastern United States. This bibliography on thermal methods of oil recovery was compiled as a part of the work. Crude oil discoveries to December 31, 1958, in the United States were estimated to exceed 270 billion barrels. Cumulative production of crude oil through 19.55 was about 60 billion barrels, and the American Petroleum Institute estimates that an additional 30.5 billion barrels are economically recoverable by present methods. On this basis, about two-thirds of the oil that has already been found can be classified as economically unrecoverable for lack of a satisfactory method. The rap icily rising costs of proving new deposit; of domestic petroleum, the lack of new discoveries of large oilfields in the united States, and I he growing demand for crude oil have caused an acceleration of research to develop new or improved methods fur producing "unrecoverable" oil in known reservoirs.

Jan 1, 1960

By Kenneth H. Johnston

For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meetings of the Kansas-Oklahoma Waterflood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1960 spring tour of four waterflooding projects in Greenwood County, Kans. (fig. 1). Three of the projects produce oil from the Bartlesville sand, and one produces from the Cattleman sand. The Bartlesville-sand floods have been in operation from 4 to 12 years and have produced about 3,910,000 barrels of waterflood oil from the injection of approximately 64,715,000 barrels of water, a cumulative water-injected to oil-produced ratio of 17 to 1. The Cattleman- sand flood, which has been operating for 3-1/2 years, has produced about 842,000 barrels of waterflood oil from the injection of approximately 9,305,000 barrels of water, a cumulative water-injected to oil-produced ratio of 11 to 1.

Jan 1, 1960

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By James Westfield

A brief résumé follows of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code fur Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous -coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reportin; to the Coal Mines Administrator any violations of the Federal Minis Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1960

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By R. V. Ramani, R. L. Grayson, R. L. Frantz, V. A. Marple, W. R. Myers, K. L. Rubow, Mutmansky. J. M., T. J. Stobbe

"An investigation of protocols for research performed from 1953 to 1988 on pneumoconioses (with emphasis on diseases related to coal and silica) was conducted in the Generic Mineral Technology Center for Respirable Dust. In addition, interviews were conducted with prominent U.S. medical researchers, aerosol scientists and engineers in government, industry, and universities to determine dust sources, dust preparation methods, laboratory protocols, and determinant variables related to in vitro and in vivo research and assess the comparability of results.Since the original report on the protocol project, additional research regarding free radical existence in freshly produced dust particles and the shape and contamination of particles generated for research purposes has further heightened scientists' concerns. As indicated by current research, fresher dust particles and those with more angular shapes may have a different level of reactivity in biological systems than do older or more rounded particles. Therefore, research on dust preparation methods for biomedical studies was undertaken and will be outlined here.Results of protocol review and interviews are summarized. Research on size reduction methods and their particle characteristics plus some recommendations concerning dust preparation methods and reporting in biomedical publications are also presented. Recent evidence indicates that these recommendations may be of importance in comparing and interpreting research results."

Nov 1, 1995

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By Albert L. Toenges, Louis A. Turnbull, EDWARD L. FISH, JOSEPH J. SHIELDS, James J. Dowd

The stripping of coal with mechanical. equipment has progressed since the introduction of the first steam-powered shovel for the retóval of overburden at a mine in Pittsburg, Kans., in 1877...From the smart steam-powered shovels with dippers of less than a cubic yard capacity, small digging radius, and shovels that required manual moving, the trend has been toward large-capacity machines. Steam as power has been replaced largely by electricity, gasoline, and Diesel fuel, and dipper capacity as great as 35 cubic yards has been attained. Shovels and drag lines are self-propelled and revolve through 360°. The cost of these large-capacity modern machines is great, and in order to assure the return of the investment during the life of the property the reserve of coal in the area to be mined must be large;" Many comparatively small areas of coal suitable for strip mining exist, but these areas probably could not be mined, profitably with this large equip- ment. Therefore, heavy equipment has not been used in small areas because of the high cost in place of this equipment, the time and Atpense required to transport the machines to the mine site, and the construction of power lines if the machines are electrical powered.. Scrapers and light excavating equipment ane mobile, and the investment cost is not high. These units have been used in sirring the coal in small areas. A study to determine the methods in, yogue, and economic considerations involved in the use of such equipment was undertaken, and the information obtained is discussed in this report.

Jan 1, 1947

By Edmund S. Leaver, R. S. Dean, T. L. Joseph

The metallurgy of manganese has developed along the lines of iron metal¬ lurgy. Enough high-grade ore has Been available so that by reduction with carbon it could be turned into an iron-ma.nga.nese alloy and a slag containing some 9 to 15 percent manganese. More siliceous ores have been smelted in the blast furnace to form iron-silicon-manganese alloys called spiegel. When lower-grade ores came in for serious consideration, which lias only been since l°l4, two types of processes received the most consideration — hydrometallurgical processes to produce a concentrate which could be smelted like the higher-grade ore and processes involving concentration of the manga¬ nese from manganiferous iron ores by preferential reduction of the iron (184)1. Special chapters in this bulletin are devoted to the production of ferro¬ manganese from ore, the hydrometallurgy cf manganese, and the Bureau of Mines modification of the preferential reduction process. Other methods of producing manganese alloys from low-grade or refractory ores have been suggested and may find future application. Manganese has a very high affinity for sulphur and is particularly adaptable to concentration by matte smelting. According to Betts (26), manganese silicate may be smelted with pyrite to give manganese sulphide and iron silicate. This method would be applicable to concentration of either the silicate or carbonate ores. The sulphide, once obtained, could be roasted to oxide and reduced in the usual way. Another possibility for the production of manganese from silicate ores involves their reduction by silicon or manganese silicides. Swedish Patent 52290, February 25, 1925. covers the reduction of a slag rich in manganese by silicon-manganese alloy containing more than 10 percent silicon, Joseph H. Brennan (38.) describes the concentration of manganese iron ores by partial reduction with silicon. Beckett (7,4,19) describes the reduction of manganese dioxide with a manganese silicide for the production of standard ferromanganese. Beckett gives as a typical alloy, manganese 64.4, silicon 24.6, and as a typi¬ cal ore, 5S.5O manganese as MnO^. The product of the reaction between these two is 80.11 percent manganese and 1.22 percent silicon.

May 1, 1934

By Lloyd Williams

1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sewanee, has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although same coal has been produced from them. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.

By Arthur C. McFarlan

There are two distinct coal fields in Kentucky-the Eastern field constituting a part of the Appalachian coal region and the Western field constituting the southern part of the Eastern Interior region. The outcrop pattern of the State is dominated by the Cincinnati arch. Coal-bearing Pennsylvanian strata occupy a low structural position on either flank, preserved thereby from erosion, which in the past has removed these same beds, though a much thinner succession, from the crest of the arch. General geological relationships are shown in figures 1 and 2. On April 13, 1750, Dr. Thomas Walker discovered the first coal recorded in Kentucky. He entered the State through Cumberland Gap (Cave Gap) and found coal a few miles north.

Jan 1, 1944

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.