Search Documents

By S. Y. Ezz

Report of discussion at February, 1971, IMM general meeting (Chairman : M. J. Cahalan, President) of a paper published in Transactions/ Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C226-C233 with contributions by Wild R. and Astier J. on fluidised bed reduction of iron ore fines

Dec 1, 1971

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

By B. H. Smith

"Most of the discoveries of nickel sulphide deposits in Western Australia have followed the search for gossans. The chances of further discoveries depend on improving our understanding of the cover of strongly leached and transported materials that obscure approximately 85% of the area of the Yilgarn Block that has nickel sulphide mineralization potential. The lateritic profiles that are observed on the Yilgarn Block today were formed over a period of more than 100 m.y. of warm and humid climates. This lateritized land surface has been preserved by induration during subsequent arid climates as well as by the structural stability of the Yilgarn Block.In geochemical surveys of lateritied terrain samples have to be taken from at least the saprolite zone usually by drilling so that confident predictions can be made of the significance of analytical data. Account must be taken of the mineralogy of samples, as well as the nature of the horizon of a laterite profile that is being sampled, owing to the concentrating effects on trace elements of Fe and Mn oxides.Multivariate techniques have been applied successfully to analytical data in gossan recognition when textural evidence is ambiguous. Pathfinder geochemistry has also been used in gossan recognition and the most significant recent advance has come from studies of platinum group metals in nickel sulphides and their dispersion during weathering."

Jan 1, 1984

By P. K. Kaiser, R. K. Brummer

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994. A risk-based decision-making procedure has been developed for selecting rockburst-resistant tunnel support in burst-prone mines. The method is based on a risk-cost-benefit analysis and uses support cost data, costs associated with the risk of support failure or excavation loss, costs associated with accidents, injuries and deaths, and the benefits achieved by installing rockburst-resistant support. It takes into account the risk of damage to the support systems due to rockbursts, potential loss of production and the need to rehabilitate in the event of a damaging rockburst. A practical example is provided to illustrate the principles involved in the decision process

Jun 17, 1905

By C G. Wall, T S. Daltaban

Three quarters of recent increases in world oil reserve estimates since 1990 have been attributed lo ‘better reservoir management' rather than to new discoveries. For the United Kingdom Continental Shelf (IJKCS), the Department of Trade and Industry (DTI) has on 2.2 bn barrels of extra oil protection through effective reservoir management of existing producing reservoirs. Past practise has been to manage petroleum exploitation on a departmental basis, with exploration assessing and ranking prospects, reservoir engineering assessing development plans and production facilities implementing plans. Any reservations necessary might involve restarting the project evaluation from scratch. Current practice is to manage an operation through asset management teams involving all disciplines. It is hoped that this approach will not only eliminate fruitless directions of effort, but the quality of work in each discipline will benefit from interaction. That is, the result of a team effort is greater than the sum of individual efforts. To date, this is most apparent with the interaction between geology, reservoir geophysics and reservoir engineering through reservoir characterization. This is the current area of greatest effort, with improved geophysical technology and computer power leading to more and more detailed and complex simulation models. The equally important interaction of reservoir engineering and production and facilities engineering applied to fields in decline has not yet achieved the prominence that it deserves. Establishing priorities in reservoir management requires the very critical evaluation of the relative value of objectives. The fact that something can be done (3-D seismic, 4-D seismic, multilateral wells, or three phase multi-layer well test analyses etc) is not a good reason for doing it. Reservoir management should he a study of value added versus cost for any activity possible or proposed. Both in the areas of reservoir data acquisition and of assessing opportunities in the period of production decline, it is likely that expert systems will need to be developed with the associated base of experience, understanding and know ledge. A n other area for the future is the elusive target of ‘enhanced ’ oil recovery, as distinct from ‘improved’ oil recovery. The most likely route forward here is the incessant scrutiny of reservoir regions and units within fields for their suitability for pilot schemes for advanced recovery techniques implemented at a favourable time. Finally, the reduction of costs, the maintenance of low. but viable rates of production and the threat of abandonment costs will increase reserves. An increase which may have appeared insignificant in the past is now more valuable.

Jan 11, 1996

By International geochemical

During the production of the Geochemical Atlas of Finland till samples were collected throughout Finland at a density of one sample per 300 km2. The material studied was the fine fraction of till (less than 0.06 mm). The geochemical mapping has shown that elements that are locally enriched in bedrock in the form of ore mineralisation are also enriched in a wide area of the surrounding till. These anomalous enrichments of ore elements take the form of rectangular or curvilinear zones that are some tens of kilometres wide and hundreds of kilometres long. The mineralised zones host ore deposits of different genetic types and can be termed "ore provinces". They stand out prominently on the geochemical maps and can be divided into sub-units of different chemical composition.

Jan 12, 1992

By Gibson J.

The writer hopes to prove that the economical tram is of even greater importance than, say, the economical engine, and as no difficult and involved calculations are required, and all the governing facts are simple and well known, the former is more easily attainable than the latter. In the first section of this paper the factors that determine the size and the construction of the tram are examined; whilst in the second section the road on which it runs is dealt with

Dec 1, 1916

By Fearnside W. G.

Further discussion at the Midland Institute of Mining, Civil, and Mechanical Engineers' general meeting held in Leeds, March 21st, 1916, with T. Beach, vice-president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p. 573 and discussion vol. L., p. 109 and 608, comprised a brief written contribution by Faulds A.

Dec 1, 1916

By J. A. Franklin, E. Broch, G. Walton

To make the best use of rock core, the mechanical character of the rock should be evaluated concurrently with conventional geological observations. The advent of simple techniques, such as the point load 'nutcracker' test, makes field logging of mechanical properties competitive with sampling and testing in the laboratory

Dec 1, 1971

By Mohammed Ali Shah, Martin Waller

The mining industry depends to a large extent on the availability of high performance equipment. For drilling this means a requirement for well engineered, reliable machines with mechanised handling and widespread utilisation of automatic control. Such machines enable performance optimisation of drilling operations and integration into a high productivity mining system. A review is presented of the current status of drilling technology as applied to the mining and minerals industry. This covers developments in: drill bit materials and design; drilling techniques; machine design; mechanisation; automation; and drilling control. It also covers the ways in which current and future mining methods and practices will influence the applications and demands placed on drilling activities. The probable impact of current research on the industry is discussed.

Jan 12, 1992

By W. Doherty, P. C. Lightfoot, V. A. Fedorenko, N. S. Gorbachev, V. I. Kunilov, A. J. Naldrett, Z. Johan

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. A model is presented which regards the Lower Talnakh- and Talnakh-type intrusions as part of the plumbing system for the overlying lavas. As magma ascended along the Noril'sk-Kharayelakh fault it was forced to spread out within sedimentary strata immediately beneath the obstruction of the accumulated volcanic sequence. Here it was severely depleted in chalcophile elements by sulphides, which were then trapped by their high density and remained behind in the main arteries to form the central, elongated zone of maximum thickness. Subsequent magma also lost Ni, Cu and PGE to the sulphides as it flowed through. The Lower Talnakh-type intrusions represent part of the plumbing system that became blocked at an early stage, before the influx of much mokulaevsky-type magma rich in chalcophile elements. The model accounts for the high metal content of the ores in comparison with the size of their associated intrusions, the extensive metamorphic aureoles, the chalcophile depletion of some overlying volcanic suites, the presence of the ore in near-surface intrusions rather than deep magma chambers, and the sulphur isotopic composition of the ore

Apr 1, 1995

By NA NA

Reports of discussion at sessions held in Keyworth, UK, on 22-23 April 1992.

Jan 12, 1992

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By M. Schwartz

Hosting copper, gold, oil and liquefied natural gas, the country is an interesting target for miners. However, remote locations in inhospitable, unusual and difficult terrain cause problems. The government has worked to create a Sovereign Wealth Fund to manage government surpluses from minerals and energy but PNG scores very low among many criteria, including land dispute resolution, as revealed by the 2014 Canadian Fraser Institute in its survey of senior mining personnel.

May 1, 2015

By C. E. Dunn

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Evidence is accumulating that reconnaissance-level biogeochemical sampling can provide valuable insight into the chemistry of the substrate. Problems such as seasonal variations in plant chemistry and the lack of a universal biogeochemical sample medium may be circumvented by adopting normalising procedures. The planet can be divided into a few climatic zones, each of which is characterised by one or two common plant genera. If it can be demonstrated that the chemical differences between certain species of a single genus are small - as is suggested by studies of boreal forests - it would seem feasible to apply biogeochemistry as a low-density geochemical mapping tool. The technique could prove particularly useful for assessing the substrate chemistry of areas of dense forest, rugged terrain and difficult access by employing airborne sampling of trees from helicopters

Jul 1, 1991

By P. Seppanen

Cemented fill was first introduced at the Keretti mine in 1952, but entailed high cement costs, the need for stope preparation, slimes handling, clean-up and maintenance, increased mine dewatering, segregation of fill and long setting times. In the 1970s research began into the use of iron blast-furnace slag as a binding agent and by 1989 Pyhasalmi, Vihanti, Keretti, Vammala and Enonkoski had saved US $11 000 000 by using slag binders instead of cement. Viscaria in Sweden and Tara in Ireland also use slag as 90-100% of total binder, although their backfilling methods vary. The main area of interest in slag research is determining the activation methods for initiating the binding reactions; it is also important to achieve other characteristics such as resistance to corrosion by sulphuric ion. New backfilling techniques developed during the 1980s included the use of high-density cemented tailings fill at Vammala and porous cemented rockfill at Enonkoski and Viscaria. Future developments focus on concepts such as integration of mining and milling with backfilling and the achievement of total underground disposal of wastes

Dec 1, 1995

By A. Hemami

In order to automate the operation of mechanical loaders it is essential to have a knowledge of the forces that act on the bucket and of the trajectory that the bucket should follow. A trajectory for the cutting edge of a bucket is derived from studies of the forces acting during the scooping phase. The proposed trajectory has a minimum energy consumption and is simple to automate. It is determined initially by setting to zero certain components of the resistive forces to the bucket motion which would otherwise result in unnecessary work and consequent energy wastage. The method for finding the appropriate trajectory is discussed on the basis of the properties of the material to be loaded and the loader size.

Jan 4, 1993

By K. M. Kinealy, A. R. Ramsden, D. H. French

A negative correlation exists between sphalerite composition and gold content when gold is transported as Au(HS)2(-); however, there are spatial and temporal differences within a single deposit. A previous model for the formation of volcanogenic massive-sulphide deposits within thermally intensifying and waning hydrothermal sytems in much the same way as is observed around modern sea-floor vents is supported. The results also emphasise that recognition of the mechanisms of gold transport in ancient deposits depends critically on an understanding of their mineralogy and stratigraphy

Jan 1, 1991

By Briggs H.

Initial discussion of the paper presented at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, included comments by Masterton J. (HM Inspector of Mines) and Sim J., and the author's reply

Dec 1, 1916

By A. L. W. Lips, T. J. R. Barclay, E. Rothery, S. H. White

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994 (originally entitled: The Broken Hill base metal deposit - a tectonically transported and modified basinal deposit within the Proterozoic Willyama fold and thrust belt). A regional structural study was undertaken which incorporated the role of shears. Their positions were identified from earlier mapping, from regional aeromagnetic data and by additional field work. Kinematic studies determined movement histories and petrological studies of the fault rocks formed within the shears identified the relationship between the movements and regional metamorphism. It was found that the shears formed a part of an earlier, major thrust event with transport from NW to SE and a later, minor one in the reverse direction. Neither had any significant effect on the mineralisation apart from local displacement, but the shuffling of the basin stratigraphy adds to the difficulty of recognising the original volcanic and sedimentary protoliths of the metamorphosed sequence. The mineralisation at Broken Hill mine is confined to a single recognisable thrust slice within a shear corridor. It is stratabound with locally transgressive remobilisation due to the high-temperature thrusting and some metasomatic alteration as a result of the retrograde shearing. This variation accounts for the different genetic models applied to the deposits in the past

Jun 17, 1905