Search Documents

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969

Recently, renewed interest in the recovery of uranium from leach solutions has necessitated a re-examination of the hydrometallurgy methods used for uranium in the 1960?s to 1970?s. A synthesizing overview of the lessons learned in those decades together with examination of recent developments in this area is warranted. This paper considers uranium recovery chemistry from acid and alkali leach solutions using solvent extraction and resin ion exchange, and provides information on circuit selection and configuration, equipment selection and design, as well as operational considerations. The unique thermodynamics of uranium solvent extraction are also presented and discussed.

Aug 1, 2010

By J. Koike

Mg alloys for structural application have attracted much attention. However, high process cost and poor mechanical reliability are major concerns upon expanding the application to a wider area. In order to break through these barriers, better ductility is desired at lower temperature. Plastic anisotropy and peculiar twin formation appear to play key roles in the deformation and fracture mechanisms of Mg alloys. In the paper, dislocation slip and twin formation are reviewed. The effects of crystallographic texture and grain size are discussed. The results suggest that a good control of microstructure and texture can improve ductility and mechanical reliability of Mg alloys.

Jan 1, 2006

By D. J. Sapsford

This paper details results from laboratory simulation of an innovative underground bioleaching process. The underground reactors are periodic flushed with recycled leachate to remove uranium that accumulates within the reactor water. This leaching cycle has been recreated within the laboratory. This study examines the influence of varying cycle protocol on uranium leaching. Protocol variants examined include variation of flushing frequency, flush volume, leachate recycle, nutrient solution (NPK) addition to reactors and Fe(III) sulphate addition to reactors. The presented data highlight the dramatic improvements in uranium recovery that might be achievable by varying the operating protocol for the actual underground reactors.

Aug 1, 2010

By I. Zhitomirsky, X. Pang

The outstanding thermal and chemical stability, excellent mechanical properties and biocompatibility of zirconia have made this material an important candidate for fabrication of advanced protective coatings on metals, graphite, carbon fibers and biomedical implants. Nanostructured polymer-ceramic composite films containing zirconia were synthesized on metallic substrates by combining cathodic electrosynthesis of inorganic particles with electrophoretic deposition of cationic polyelectrolytes. Thick crack-free oxide and composite coatings were obtained using this newly developed technique. The deposits were studied by thermogravimetric analysis, X-ray diffraction analysis, scanning electron microscopy and atomic force microscopy. The mechanisms of deposition are discussed.

Jan 1, 2004

By A. M. Hadian

The use of dolomite refractories in steel making and cement industries has advantages over other basic products particularly in countries where this type of refractories is produced. Due to existence of high-quality dolomite deposits in many regions of Iran, there is a good potential for producing dolomite refractories in the country. This study focuses on the effect of such additives as iron oxide and alumina on hydration resistance and density of Iranian dolomite. It was found that addition of Fe2O3 is more effective than Al2O3 on increasing density as well as resistance to hydration of dolomite.

Jan 1, 2004

By W. L. Stuewe

For the purpose of this paper I shall, in order to limit myself, define the words 'Maintenance' and 'Equipment' as follows: Maintenance shall mean the 'care of or 'the sustaining of equipment in as nearly perfect condition as possible. Equipment shall mean any item of a mechanical nature entering into the production of coal; it will be seen that unless one limits the use of this word it could take in administration as well as operative equipment, and include metal mines, mills and smelters, and manufacturing plants. In any industry the first consideration is the proper operation of all units entering into the production of the article manufactured or produced. I wish to quote here what a man, well known internationally in financial circles, told his operators at the time a large expansion programme was under consideration. His exact words were: "I do not care how much it is going to cost. What I want to know is how much it is going to cost to operate and maintain. It is the continuous drain for repairs that costs us the most money." The truth of this statement has been proved time and again, and many companies have found the cost of maintenance to be the balance between profit and loss-so much so that, in two instances with which the writer is familiar, the mechanical equipment was practically replaced throughout. I bring this point out here to emphasize the value and necessity of keeping abreast of the times, and obtaining maximum efficiency with the minimum outlay. Time is indeed money where delays occur due to defective or poorly kept equipment, and it is absolutely necessary to prevent machinery from becoming defective or inefficient.

Jan 1, 1930

By Douglas Lay

Attention has been drawn in the publications of the Department of Mines to the view that veins of two different ages occur in the Cariboo district, namely, those of Jura-Cretaceous age and those of pre" Mississippian age. It has been further pointed out that while there is doubtless a wide distribution of veins of pre-Mississippian age in and about the Barkerville and Stanley areas, and in the vicinity of Round Top mountain and Yank's peak, there is no such wide distribution of veins carrying gold values of commercial significance. Veins of the latter type discovered to date occur almost exclusively within one or other of two comparatively narrow zones, both trending northwest and southeast, the one extending from Island mountain co Round Top mountain, and the other from a point somewhat north of Stanley co Yank's peak. In addition, there is some evidence of a third zone trending northwest from Spanish mountain, at or near the contact of the pre-Cambrian and Mesozoic rocks. In short, all the evidence from prospecting and lode-mining operations to date indicates that values are mainly restricted co zones having marked directional distribution. Moreover, it can be demonstrated that the placer deposits resulting from the erosion of the pre-Mississippian veins have a similar directional distribution, allowance being made for modifications due to glaciation. The observations offered in this paper are of the nature of a generalization which seeks to explain certain anomalies both in the vein-mineralization and in the -important auriferous-pyrite replacement deposits in limestone which have recently been discovered. For the sake of brevity, the Island Mountain-Round Top Mountain zone will be referred to as Zone No. 1, and the Stanley-Yank's Peak zone as Zone No. 2.

Jan 1, 1936

Ni and samaria-doped ceria (Ni-SDC) cermet are desirable materials for making a solid oxide fuel cell anode working at intermediate temperature (800°C or lower) due to its good ionic/electronic conductivity at the reduced operating temperature. An advantage of the use of a Ni-SDC anode is the enlargement of the effective reaction zone in the interfacial area between the anode and the electrolyte. As a result of the mixed ionic/electronic conductivity of the anode, the electrode reaction rate is enhanced. Investigations into the properties of the ceria-based anode reveal that the performance of the anode is closely related to its microstructures, which are dependent on the composition and fabrication conditions of the ceramics. In this paper, a method for quantitative characterization and correlation of Ni-SDC cermet microstructures to the performance of an anode is investigated. A series of Ni-SDC anode samples are prepared by screen-printing (SP) and spin-coating (SC) techniques, and different microstructures of the samples are obtained through controlling the SP or SC conditions and the sintering temperature. Individual phases (Ni, SDC and pore) in the tri-phase boundary (TPB) microstructures in the electrode are differentiated and segmented from each other in optical and SEM images based on the differences in refractivity and atomic contrasts among the phases. The geometric properties of the segmented phases are characterized using image analysis methods, so that a quantitative skeleton illustrating the TPB microstructures of the Ni-SDC electrode is obtained. Statistical analysis of the distribution of the three phases in the TPB microstructures is performed and the relationship of the microstructures with the optimum electrode is interpreted in terms of the microstructure analysis data.

Jan 1, 2005

By C. Caners

One of the main uses of fossil fuels is in the transportation sector, leading to environmental consequences such as climate change. In order to move towards a more sustainable energy infrastructure, a transition must begin from fossil fuels to renewable fuels, derived from e.g. biomass. One means of facilitating this transition is to develop reforming technology that can extract hydrogen from a suitable fuel that is either fossil fuel or renewable in origin. The hydrogen would be feed to a 'fuel cell' engine that would power the car, truck or bus. One reforming technology that is attractive for automotive applications is autothermal reforming (ATR). Autothermal reforming is the combination of steam reforming and partial oxidation, whereby a portion of the fuel is combusted using a sub-stoichiometric amount of air, and the resulting thermal energy drives the more desirable steam reforming reaction. ATR is attractive for fast start-up, rapid load following and ease of control. ATR also has the benefit of smaller volume and fewer peripheral requirements as compared to other reforming technologies. Recently, a bench-scale gasoline autothermal reformer (ATR) was constructed and tested. This ATR employs a novel design, consisting of three concentric annuli in order to promote heat transfer from the partial oxidation reaction to the steam reforming reaction. Concurrently, a CFD based model (FLUENT) of the ATR that considers the geometric complexity of the reformer was validated. In spite of the use of simplified kinetics, the model predicted well the observed trends in temperature and overall performance. This paper will discuss the use of the model to improve the design of the ATR. The impact of various system parameters upon performance will be investigated along with alterations in the geometry of the ATR. The various tradeoffs in performance and system volume/size will be highlighted in the context of a fuel cell power system.

Jan 1, 2005

By G. H. K. Pearse

Sulphur is derived from both 'voluntary' and 'involuntary' production. The former category includes sulphur obtained from elemental sulphur deposits and from pyrite and gypsumanhydrite deposits. Sulphur in the latter category is produced by pollution abatement at fossil Juel plants and from treatment of metallic sulphides. Canada is the world's largest sulphur exporter and third largest producer. Main resources of Canadian sulphur are sulphurous fossil fuels, metallic sulphides and native sulphur. Only the first two sources have produced sulphur in Canada 10 date; the first source accounts for over 85% of total Canadian production. Future sulphur sources will be derived increasingly through pollution abatement and decreasingly through voluntary production.

Jan 1, 1984

By D. MacGREGOR, VERA TUREK

The St. Canul and Ste. Scholastique orthoquartzite sanrjstone deposits are located within the Potsdam Formation near Montreal. The sandstone lies on Precambrian basement and is Cam/3rian to Ordovician in age. The Potsdam Formation shows two distinct stages of development. One created a deepwater facies represented by impure, limey or shaley sandstone; the other produced a shallow facies composed of grey, highpurity sandstone. The shallow-water orthoquartzitic sandstone at St. Canul is being mined and beneficiated by lndusmin Limited. The operation manufactures a wide range of silica products and supplies industrial areas of Quebec and Ontario with material for the glass, foundry, silicon carbide and ceramic industries.

Jan 1, 1984

Cameco Corporation is in the process of revitalizing the Key Lake mill. As part of this process, the company is considering installing the Rabbit Lake style strong acid stripping in solvent extraction. This would lead to using hydrogen peroxide for uranium precipitation. The process currently employs ammonia stripping and ammonia precipitation. As part of the process evaluation, an indirect fired drier pilot plant test was conducted. This paper will discuss the results of that test work, including the relationships between the following: ? Drying temperature and product grade ? Drying temperature and product colour ? Drying temperature and product reactivity with water ? Drying temperature and energy input requirements ? Drying temperature and shipping costs

Aug 1, 2010

By Z. S. Abisheva

The Zhezkazgan copper sulfide ore deposit in Kazakhstan contains both rhenium and the rare osmium isotope "osmium-187" (187Os) in the high isotopic purity of 99.4 ± 0.2%. This isotope is believed to have originated as a result of the disintegration of one of the rhenium isotopes, according to the reaction: 187Re75 ?> 1870576 + B- + v~ (where B is a 13-particle, v~ is a 3-disintegration antineutrino). The distribution of osmium and rhenium in metallurgical byproducts produced during the recovery of copper from these ores has been studied and process flowsheets for the processing of rhenium and osmium-containing byproducts have been developed.

Jan 1, 2007

By Peter McBride

Human excellence in all areas of endeavour is acknowledged and recognized. Establishing role models and spreading the word on best practices helps broader audiences. For on-the-job safety, recognition awards are a component of successful programs. In Canada?s mining industry since 1941, the John T. Ryan Safety Trophies initiative has contributed to the sector?s improving record in this area. The much sought after and rich in history John T. Ryan trophies are recognized symbols of safety excellence in Canada. The effectiveness of the Ryan safety recognition program in Canada has led to its export to other mining countries seeking to improve their overall safety performance.

May 1, 2008

By L. V. Bell

"The gold deposits of the Caribou mine are representative of those of the Province of Nova Scotia as a whole. The ore shoots within the deposits, in common with those elsewhere within the Province, are associated usually with interruptions or irregularities in the broader and uniform fold structures. The structural factors localizing ore deposition as applied more specifically to the Caribou mine are demonstrated chiefly by the close relationship of the two principal ore shoots, known as the main orebody and the 'high-grade' vein, with a pitching drag fold developed in the southeast limb of the major northeast-southwest trending anticlinal fold or elongated dome that constitutes the primary structural feature of the Caribou gold district. It is of interest to note that the evidence indicates that this drag fold, in common with other folds subsidiary to the primary fold, formed as a result of movement similar in nature to that which caused the primary fold itself. Presumably, therefore, these folds are coincident in time.The property described here as the Caribou mine is an amalgamation of two adjacent properties formerly known as the Ross and the Nova Scotia Gold, but which since 1934 have been controlled and operated as a unit by The Consolidated Mining and Smelting Company of Canada, Limited. The Caribou mine is situated in the Caribou gold district about 45 miles to the northeast of the city of Halifax and about 6 miles to the north of the Moose River gold district.The history of mining at Caribou dates back to 1867. The first recorded gold production is for 1869. From 1869 to 1933 the gold produced from the mines of the Caribou district aggregated 47,249 oz. from 93,234 tons of ore treated. The grade of the ore on the basis of the gold actually recovered from the district would thus average 72 oz. gold a ton, which, as will be noted from the following, is precisely the grade of the ore treated from the Caribou mine during operations by The Consolidated Mining and Smelting Company. These operations commenced in September, 1934, and milling on a commercial basis was under way during 1938. Since that time production, apart from a short period in 1945 during which efforts were concentrated on development work, was continuous to early in 1947, when the mine closed down owing to exhaustion of the known orebodies. Gold produced from the Caribou mine by The Consolidated Mining and Smelting Company from September, 1934, to the close of 1946 aggregated 43,205 oz. from 90,754 tons of ore milled; the grade of ore treated averaged 0.50 oz. gold a ton. The indicated average grade of O.S oz. gold a ton for the ore of the Caribou district throughout its mining history ranks somewhat higher than the 0.37 oz. a ton average for the ore milled to date from the several gold districts throughout the Province as a whole according to the production statistics of the Provincial Department of Mines."

Jan 1, 1954

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By George Hope, Dave Green, Jacques McMullen

The Est Malartic mill has been treating massive sulphide, copper/gold ore from the Bousquet 2 mine since 1989. The need to minimize copper content in flotation tails which are leached for gold recovery and to produce a saleable copper concentrate led to the evaluation of Conventional, Column and HG flotation methods. The HG method was preferred and two full-scale cells were installed and operated over a two-year span. In 1992, it was decided to expand the mill capacity from 1500 tpd to 2500 tpd. A total of nine additional HG Tank Cells were installed to provide additional roughing and cleaning capacity. The expanded plant has been operating since June 1993.

Jan 1, 1994

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By A. Cadieux, J. -B. Pineault, C. Allaire

The temperature measurement of the molten metal in the aluminum transformation process is of prime importance. This is particularly the case for aluminum treatment furnaces, such as holding and melting furnaces. Such reverberatory type of furnaces involve a thermal gradient across the metal line which limits the life of conventional thermocouple protective ceramic shields, due to the action of locally induced thermal stresses. This paper presents a novel thermocouple assembly using a composite refractory protective shield allowing long term resistance to such above conditions. Example of results obtained from various tests in aluminum holding furnaces are presented. The results confirm the superiority of the novel thermocouple assembly, as compared to conventional thermocouple units.

Jan 1, 2004