Search Documents

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By R. S. Nichols

"During 1973 to 1978, Canadaka Mines Limited, a subsidiary of St. Joseph Explorations Ltd., undertook an extensive exploration and development program in the Cobalt area. This program resulted in the delineation of previously unknown stratigraphic units in the Archean volcanic sequence. During this time period, significant are controls related to area silver deposits were also identified.The Archean geology is comprised of a volcanic pile conformably overlain by sediments. The volcanics contain at least two felsic volcanic centres near the stratigraphic top of the pile. The bulk of the pile consists of mafic flows and interflow sediments. lnterflow sediments around silver are shoots contain mineralized halos of base metal sulphides. The halos exhibit lateral and vertical metal zoning with Cu, Pb and Zn mineralization decreasing away from an are shoot.Silver mineralization controls determined during the Canadaka program agree with the historically well established importance of Coleman sediments as well as Archean contacts for hosting silver deposits. The vertical extent of are shoots is typically 150to 250ft. A strong correlation was found to exist in the Cobalt area between Archean strike and the strike of are veins. Finally, al/ Cobalt area are deposits appear to be associated with a distinct volcanic pile at the top of a sequence of Archean flows."

Jan 1, 1988

By Garry Biles, Ken Major, Raj Anand

"Prime Resources Group Inc. (Prime) commenced the Eskay Creek Mine operations in 1994 in northern British Columbia. The ore from the underground mine is crushed and shipped to smelters in Japan and Canada. The nominal production rate is 300 tonnes per day.Before commencing the above operations, preliminary evaluations for the high grade gold mine had indicated that an extremely complex metallurgical and chemical process flowsheet would be required to recover the economic metals. Subsequent to the metallurgical testing program, Prime identified markets for the untreated ore and initiated underground mining and ore transportation operations.Prime recently identified lower grade ore zones, which are less economic or uneconomic to mine and ship directly to the smelters. Test programs were initiated to evaluate processes for upgrading the ore to a marketable product. In 1997, Prime will complete the engineering and construction of a 150 tonne per day flotation plant to concentrate the gold and silver values for the NEX and 109 zones. The mine will then, in addition to the direct shipping of the shippable ore, ship concentrate from the millable ore. This paper discusses the development and design of the flotation plant.IntroductionThe Eskay Creek Mine is located in north-western British Columbia approximately 83 km north-west of Stewart, B.C. as shown in the location map Figure 1. Access to the site is provided by a restricted access gravel road from Bob Quinn Lake junction of highway 37, a distance of about 59 km. The work force at the mine is based on a two-week rotation schedule. Employees are flown from as far away as Vancouver to Smithers by commercial airlines and then from Smithers to the Bob Quinn airstrip by local charter. During poor weather conditions, transportation to site is by vans that take about six hours to travel the 450 km road distance."

Jan 1, 1998

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates the prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed.

Jan 1, 1966

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates t he prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed

Feb 1, 1966

By Steven Dempsey

Overview What is Tubbing? A look at Cigar Lake Tubbing Design The Tubbing Installation Backwall Grouting

May 1, 2013

By J. E. Lee

"This paper describes the current practices and experiences, and discusses design parameters concerning slurry pumping at Inco Metals Company in the Sudbury District. It deals mainly with the long tailing and concentrate lines. Subject matter is arranged under the following headings: pumps, lines, instrumentation, system design, operation.IntroductionThe Inco Metals Company is the mining and processing section of INCO LIMITED. In the Ontario Division, it operates 13 mines, 5 mills, a smelter, an iron ore plant and 3 refineries, all engaged in the mining and recovery of nickel and copper. This paper describes the slurry pumping practices in the mills of the Ontario Division.The PumpsWe have in our Sudbury area mills most of the available types of slurry pumps, in sizes from one inch up to twelve inches, a total of about 400 pumps. The rubber-lined, horizontal shaft pump is; most numerous. However, for certain applications, the hard-metal pump is essential, and is becoming more popular for general mill service. Two types of vertical shaft pumps are used. There are a few diaphragm pumps on small thickeners, but the larger thickeners have centrifugal pumps either directly connected to the under-flow or with one pump handling several gravity underflows. We have not used piston or plunger pumps in our mills."

Jan 1, 1978

By S. Ghafarnejad Parto, Å. Rasmuson, A. Fredriksson, M. Mohammadi, K. M. Forsberg, J. Martinez De La Cruz

The present study aims at recovering rare earth elements (REE) in conjunction with the production of fertilizers from an apatite concentrate. Apatite is one of the REE rich minerals ending up in the tailings pond when Luossarvaara-Kiirunavaara AB (LKAB) in Sweden processes Malmberget’s iron ore deposit. Leaching with nitric acid, hydrochloric acid, and sulphuric acid respectively have been studied. The nitric acid route was chosen for further investigations and the optimum acid concentration for leaching of the REE were determined. The leached REE are recovered by solvent extraction using di-(2-ethylhexyl) phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid-mono-2-ethylhexyl ester (EHEHPA).

Jan 1, 2014

By Peter Godbehere, Christian Desroches, Viken Baboudjian

"Noranda Copper Smelting and Refining is a unit of Noranda Metallurgy Inc., comprising the Home smelter in Rouyn-Noranda, Quebec and the C.C.R. Refinery in Montreal East. The Home smelter provides custom smelting services for a wide variety of copper and precious metal bearing concentrates and recyclable materials, producing over 200 000 tonnes of anodes and 450 000 tonnes of sulphuric acid annually. The C.C.R. Refinery has an annual production of 360 000 tonnes of copper cathode, and is a major refiner of precious metals.Over the past twenty years, Noranda Copper has developed innovative processes and operating techniques to treat the ever increasing complexity of primary feed materials, while improving the quality of its final products, working conditions and reducing environmental emissions.This paper presents an overview of the operating practices of Noranda Copper with particular emphasis on the impact of impurities in the smelting and refining processes.IntroductionThe treatment of custom materials has been practiced by Noranda Copper since commencement of operations at the Home smelter in 1927 and the CCR refinery in 1931. Copper concentrates from a wide variety of regional, North American and overseas producers account for the bulk of the 800 000 tonnes treated annually, although recyclable and secondaries have increased in importance as feed sources in the past two decades. The geographical disadvantage of the Horne smelter compared with most custom smelters located on tidewater has provided an important incentive for Noranda Copper to develop the necessary technology and operating practices at its smelter and refinery to treat high value complex concentrates and other feeds containing significant concentrations of bismuth, antimony, arsenic, lead, tellurium, mercury, etc."

Jan 1, 1995

By Frank Ebbutt

Introduction The property of the Britannia Mining and Smelting Company, Limited, is situated on the east side of Howe sound, about six miles from its head. It is roughly thirty miles by water from Vancouver, one of the important ports of the Pacific and the industrial and financial centre of British Columbia. Howe sound is navigable for ocean-going vessels and Britannia Beach is a daily port of call for the commodious boats of the Union Steam-ship Company, sailing from Vancouver. Few mines are so ideally situated or have so many or varied natural advantages. Copper was first found on Britannia mountain in 1888, by Forbes, but it was not until 1898 that five claims were staked here by Oliver Furry, a trapper. It is from these claims that the major production during the past thirty years has come. In 1900 the Britannia Copper Syndicate was formed and development of the property was commenced. In 1903 the late Grant B. Schley obtained control, and through his efforts the Britannia Mining and Smelting Company was organized in 1908 as a subsidiary of the Howe Sound Company. Since that time, a persistent and progressive policy has been followed, which has resulted in a prolonged and profitable operation. The country in the immediate vicinity of the mine is marked by strong relief, with mountains rising abruptly from tide-water to elevations of 5,000 feet and more. Two broad transverse valleys deeply dissect the area. These are the valleys of Britannia creek and Furry creek. The region has under-gone prolonged and relatively recent glaciation. Over much of the surface there is deep overburden and dense vegetation. The geology of the mine and vicinity has been described in reports by S. J. Schofield (1), H. T. James (2), J. G. Barry, and others (3). The present writer is in accord with much of this literature on Britannia, but during recent years, extended observations made underground have shown that the 'quartz porphyry', or 'mine porphyry', of several of the earlier writers is not the host rock to the commercial mineralization; and he contends that the mineralization occurs in highly altered phases of a complex series of ruffs, flows, and pyroclastics and their autoclastic metamorphosed products.

Jan 1, 1935

By Ward E. Kilby, Bruce I. Mcclymont

"Data from the South Fork Pit Area of the Bullmoose deposit in northeastern British Columbia are used to demonstrate the usefulness of microcomputers to the on-site geologist. The technique utilizes a series of digital surf aces in the form of a network of points to define various geologic parameters such as seam positions, topography and coal quality characteristics. Manual digitizing, kriging and combinations of these techniques are used to calculate these digital surfaces, the best method depending upon the type and quality of the data in question. Digital surfaces, each modelling a specific feature when combined and manipulated with the computer form a powerful tool, the deposit model. The resultant model, containing all the surfaces, is used to examine seam and inter-seam thicknesses, deposit volumetrics, seam quality characteristics and the adequacy of sampling.IntroductionCoal deposit modelling using computer-based techniques has become routine. However, a geologist working in the field, without access to mainframe or minicomputer, ha s considerable difficulty implementing these procedures. However, microcomputers, which are portable and inexpensive can handle exploration data, perform various geological analyses, and produce deposit models virtually at the same time as the data is being collected. For the on-site geologist this means that quick access to the results of such modelling could point out inadequacies in deposit definition and trends in coal quality deserving investigation."

Jan 1, 1985

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By J. M. D. Wilson, W. Petruk, C. Coté

"The behaviour of minerals in the Mount Wright spiral circuit was investigated to find methods of improving iron oxide mineral liberation and recovery. The feeds, concentrates and tailings from rougher, cleaner and recleaner spirals in one mill line were sampled before and after the sizing screen openings were reduced from 2 mm to 1.6 mm. Sized fractions of each sample were analyzed with the MP-SEM-IPS image analysis system at CANMET to determine mineral quantities and liberation characteristics of the iron oxide minerals. Mass balance techniques were used to calculate stream recoveries of iron, silica, total iron oxide minerals, hema¬tite, goethite, quartz, ferromagnesian silicates, and liberated and locked total iron oxide minerals for each sieve fraction.The reduction of the sizing screen openings increased the ap¬parent liberation of the total iron oxide minerals in the screen undersize from 89% to 94% and raised the over-all iron recovery from 84.4% to 85.3%. Apparent liberation of iron oxide minerals in the cleaner sand also increased from 70% to 85%, but the – 75 µm fraction re¬mained the only fraction containing an acceptable amount of liber¬ated iron oxide minerals in each case. Due to limitations of spiral and grinding efficiency it is recommended that the cleaner sand be screened at 300 m, the +300 m fraction be reground, and the – 300 p.m fraction be rerouted to the rougher spirals.The amount of fine liberated iron oxide minerals (– 106 m) lost in the tailings was 46 TPH in mill line 3. This value represents 41 wt % of the free fine iron oxide minerals, or 7 wt % of the total iron oxide minerals in the spiral feed. Further work is needed to investigate the possibility of recovering this material by other methods.Middling iron particles (010 50%) and presumably free gangue in the size range –300+ 75 m tend to be recovered by spirals by entrapment."

Jan 1, 1990

By Nigel J. Cook

"Detailed mineralogical examination of gold-bearing rocks, ores, concentrates and other samples should be considered an integral part of any study of a deposit for which exploitation is being planned. Adequate mineralogical study, although time consuming and often costly, can significantly improve understanding of the mineralization, can help to optimize the results of any metallurgical testing and can be of great value in case of potential trouble-shooting. The advantages and disadvantages of various examination techniques are discussed with reference to a number oj mineralogical studies oj Canadian gold-bearing samples.IntroductionVarious authors, notably Gasparrini (1983), Harris (1989) and Henley (1990), have stressed that mineralogical study of gold ores is critical to successful and efficient beneficiation. Only in cases where diagnostic cyanide leach testing is successful can detailed mineralogical examination be disregarded. Such examination of gold-bearing rocks and metallurgical products is all too often neglected because the methods involved are believed to be time-consuming, costly, and may carry a considerable degree of inaccuracy. Commonly, bulk metallurgical testing is, carried out without prior or concurrent mineralogical examination, causing the results of the testwork to be difficult to interpret, or in some cases, misleading. This, in turn, may lead to> significant delays to the project at the feasibility stage or mean that understanding of the sample is limited, preventing the introduction of prudent modifications at a later stage if problems arise. Mineralogical studies may guide the successful implementation of a metallurgical test program."

Jan 1, 1990

By Young C. Kim

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. However, no formal framework for a proper analysis has existed to date. This paper summarizes the material contained in the Design Chapter Supplement (5-3) of the Pit Slope Manual. The supplement describes the results of the research effort in which a formal economic analysis framework was developed and tested through a case study. The case study results have demonstrated the practicality of the developed procedure and the availability of required data under "real-life" conditions.

Jan 1, 1979

By Magdy Ibrahim

Detailed as-built project schedules are necessary to close out construction projects, benchmarking, forecasting, dispute resolution, and improving cost estimates of future projects. Manual procedures for developments of as-built documentation is time consuming, involves numerous interfaces and human interventions. This paper presents computational framework that encompasses automated site data acquisition and generates schedule updates utilizing commercially available project scheduling software. The work is carried out collaboratively with a Hydro Quebec team. The site data is captured employing mobile computing using iPad® type computers and Wi-Fi. The information is directly compiled in a centralized database server. The synchronization tool is a bi-directional application and is used on servers to communicate with iPad® computers deployed onsite. The captured data is stored in Microsoft SQL® relation database that consists of 63 entities. Computer software application has been developed in Microsoft Visual Basic® (vb.net) environment for extracting the collected site data, linking the database to the as planned schedule, and generating the actual, also known as as-built schedule. The development can be utilized in automated progress reporting, evaluating future bids, generating master schedules and a wide range of efficient EVM applications.

Aug 1, 2013

By Mark Stephenson, Paul Henharen

"The objective in the mineral processing of primary ores is to liberate and effectively recover each individual economically viable diamond with minimal reduction in its potential value.There are three distinctive phases in diamond processing:Feed PreparationWhere the diamonds are liberated and waste material finer than the economically selected cut-off size is rejected. In this section we will discuss the various techniques utilised worldwide to effect feed preparation.Primary ProcessingWhere the diamonds are recovered into a high grade concentrate suitable for the more expensive and selective final recovery process. In this section we will discuss the development of primary processing from jigs and pans to the more current techniques utilised worldwide.Final RecoveryWhere there is selective rejection of waste particles until only diamonds remain. The diamonds may then be acidised prior to packing and marketing.Within these distinct phases a variety of unit processes have been utilised and this paper will discuss their relative merits, limitations and suitability in respect to the various stages of diamond project development from prospecting through to production.Basic capital and operating costs are compared for the autogenous milling route developed in the CIS and the crushing and scrubbing route utilised in the west."

Jan 1, 1994

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By Arthur Lieu

Outline Removal mechanisms of Se and Mo in the Key Lake Bulk Neutralization circuit Bulk circuit Detail process modification in the Key Lake BN circuit Process performance after commissioning Objective Legacy effects of Se and Mo from the historical operation of Key Lake mill were shown to have an negative effect on the regional biota in the downstream environment. The water treatment circuit was not designed to remove Se and Mo from the effluent. Reduce Se and Mo concentrations in final effluent under0.028 0.028 ppm ppm and 0.3 and ppm ppm(CNSC regulatory limits).(limits).??????

Nov 1, 2011

By D. M. Ward

"The uranium deposits upon which the Rabbit Lake project story is based are located at the eastern margin of the Athabasca Basin just west of Wollaston Lake in northern Saskatchewan. This paper provides a general review of the exploration history for the major deposits and the influence of an expanding geological data base, which served to guide the continuing exploration programs.A brief description of each of the deposits is provided in order of their discovery and with emphasis upon their relative geological and mineralogical characteristics.The Rabbit Lake and Eagle Point orebodies are monometallic uranium deposits localized by thrust faults within the Aphebian Wollaston Group. The Cof/ins Bay A-zone, B-zone, and D-zone are polymetaflic U, Ni, As, Co (Au , Ag) deposits located within the Helikian Athabasca Group at its unconformable contact with the underlying Wollaston Group. INTRODUCTIONThis paper demonstrates the importance of applying the accumulated geological knowledge, gained through the exploration, mining, and development process, to the ongoing success of exploration programs. To emphasize this point, the basic geology of each of the major Rabbit Lake area deposits will be presented in chronological order of their discovery and subsequent development. These depos its include Rabbit Lake, Collins Bay A-zone, B-zone, D-zone and Eagle Point. The geological descriptions are based primarily upon the detailed observations of many current and former geologist s employed by both Gulf Minerals Canada Limited and Eldorado Resources Limited. Much of the early historical data was obtained from Dr. E.E.N. Smith, formerly with Eldorado Resources Limited. Regional GeologyThe Rabbit Lake area which includes the Rabbit Lake, Collins Bay A-zone, B-zone, D-zone and Eagle Point deposit s, is located on the eastern edge of the Athabasca Basin close to the western shores of Wollaston Lake (Fig. I). The area is in the Churchill Province of the Canadian Shield within the Wollaston lithostructural domain, at the eastern edge of the Athabasca Group. The uranium deposits occur within both the Wollaston Group metasedimentary assemblage of probable early Aphebian age, and the diagenetic ally altered quartz sandstones and conglomerates of the Athabasca Group of Paleohelikian age. Both units unconformably overlie granitoid gneisses interlayered with metasediments and a graphitic iron formation all believed to be of Archean age. All uranium depo sits in the Rabbit Lake area occur in close proximity to the Paleohelikian - Aphebian or Paleohelikian - Archean unconformity."

Jan 1, 1989