Search Documents

By J. Sugai

Formability of extruded round AZ31 magnesium alloy tubes with different manganese concentrations was evaluated by performing bending tests and measuring strain along the length of the tubes during the bending process. It was found that an increase in the manganese content from 0.3 % to 0.7% did not exert any significant effect on the values of yield stress, elongation, or compression to fracture. However the hardness tended to increase and the UTS decreased. The compressive ductility was significantly lower than tensile ductility for all manganese concentrations. Consequently, the formability of tubes decreased, causing cracks in areas where compression strain occurred during bending. It was also found that a larger strain occurred in the latter half of the region along the length of tube between the clamp-end and the tube-positioning block. Within this region, alloy tubes with higher manganese concentrations, 0.5 and 0.7 %, there was a clear strain peak within the strain profile, while for the 0.3 % Mn alloy, a more uniform strain profile was exhibited, indicating a more uniform deformation. This was confirmed by microstructural analysis of the specimens.

Jan 1, 2006

By Wengui Su, Qi Zhang, Junce Wang, Zhijun Ma, Xingyuan Weng

"Mesoporous materials with large specific surface area, pore size, and pore volume have been widely used in many fields such as ion exchange, gas separation, adsorption, and catalysis. Mesoporous materials prepared using natural zeolite have the advantages of both acid and alkali resistance. In this work, mesoporous materials were prepared using natural zeolite as the starting material and diethylenetriamine (DETA) as a template. The resulting samples were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) and N2 adsorption-desorption experiments. The influence of the crystallization temperature and crystallization time on the specific surface area, pore volume, pore size, and morphology of the resulting mesoporous materials are also discussed. Our results show that for an increase in both the crystallization temperature and time, the average pore size first increases then decreases, while the specific surface area first decreases then increases. Based on this work, we concluded that the optimal crystallization temperature was 2003 and the optimal crystallization time was 60 h. These conditions gave an average pore size of 17.93 nm, a pore volume of 0.048 cm3g-1, and a specific surface area of 16.48 m2g-1.INTRODUCTIONMesoporous zeolite, as the name implies, is a highly porous crystalline zeolite. This material is of interest due to its high hydrothermal stability, its adsorption and diffusion properties for macromolecules, and its excellent selectivity and activity as a catalyst. In recent years, it has become a hot spot among research of porous catalytic materials and has been widely used in petroleum and natural gas processing, fine chemical processing, various adsorption and separation tasks, and other uses (Carvalho & Urquieta- Gonzalez, 2015; Teh, Triwahyono, Jalil, Mukti, Aziz, & Shishido, 2015)."

Jan 1, 2016

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By J. Etcheverry, E. Seguel, R. Díaz, F. Parada, R. Parra, E. Balladares

A thermodynamic and kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite during partial roasting of enargite-containing copper concentrates. The proposed mechanism involves solid-solid-gas and solid-gas reactions between chalcocite, pyrrhotite, gaseous sulfur and oxygen. The formation of bornite could be explained by a two-step reaction: the first one involving the formation of chalcopyrite by a reaction between Cu2S, FeS and gaseous sulfur, followed by a second step in which the newly formed chalcopyrite reacts with additional chalcocite to form bornite. Although thermodynamically the direct formation of bornite is more favorable than that of chalcopyrite, the lower diffusion kinetics of bornite formation could explain the preferential formation of chalcopyrite. If the reaction occurs with stoichiometric chalcocite and pyrrhotite in the presence of gaseous sulfur to form chalcopyrite, no bornite is formed, while for the stoichiometric reaction between chalcopyrite and chalcocite in the absence of sulfur, only bornite is formed. For the formation of magnetite and chalcopyrite the mechanism could involve the partial reaction of chalcocite and pyrrhotite in the presence of oxygen. The proposed model is thermodynamically consistent with the experimental results obtained in laboratory and pilot plant. INTRODUCTION The processing of high-arsenic copper concentrates with over 0.7 wt.-% arsenic by conventional smelting-converting normally require an additional arsenic removal step to reduce arsenic content to levels below 0.2–0.3%. One of these high-arsenic copper concentrates is the one produced by the Ministro Hales Division (DMH) of CODELCO, which has the typical chemical composition shown in Table 1. Enargite (Cu3AsS4), chalcocite (Cu2S) and pyrite (FeS2) are the main mineralogical species present in these concentrates, with over 75 wt.-%, as shown in Table 2. Partial or “neutral” roasting of these concentrates under controlled temperature and partial oxygen pressure conditions at 923–993K (650–720ºC) can remove up to 95% of the arsenic as As2S3 (As4S6), which has a high vapor pressure under these conditions, leaving a calcine with low residual arsenic. In copper concentrates, arsenic is present generally as enargite and arsenopyrite. This compounds as well as others such as pyrite and covelite, decompose readily above 770 K (500ºC), releasing, in addition to gaseous arsenic trisulfide, gaseous sulfur which by oxidizing to SO2 generates most of the heat required by the process.

Jan 1, 2019

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By N. P. Hristov, L. V. Kuzev

"A simulation study of the fill factor of a drum mill was conducted using two types of grinding media: balls and tetraballpebs. Each medium was composed of equal number of grinding bodies having equal weight but different shape. The difference was in the density of the two grinding media.Standard spherical grinding bodies (balls), which were used in practice, and equivalent (by weight) grinding bodies in the shape of spheroidal tetrahedrons (tetraballpebs) were studied. The simulation was conducted in a module of a 1.2 m diameter drum mill, whose length exceeded twice the diameter of the corresponding grinding body. The grinding balls had a few percent (3 to 6) higher fill factor than the grinding tetraballpebs in the same shell.Vertical sections of the grinding medium were taken across the studied shell module along its axis. They showed the location of each grinding body in the fill volume. Defects in the packing of the grinding bodies and the contacts between them and with the inner surface of the shell were also show. Differences in the contact points of the balls and the tetraballpebs were noted. For the tetraballpebs, we observed contacts both between the spherical surfaces and with the edges and vertices of the grinding bodies.The topography of the grinding media is shown visually.INTRODUCTIONThe grinding balls have been studied extensively. It is the traditional grinding medium in ore processing industry. The parameter characterising the grinding medium is its density. It is the mass of the grinding medium per unit of volume. The parameter may have a range of values. It depends on:• The physical properties of the material they are made of;• The shape of the grinding body;• The dimensions of the body;• Size distribution of the grinding bodies in the grinding media.In comminution, the fill factor of the mill shell is the process parameter that is representative of the grinding medium. Some publications have indicated the disadvantages of ball grinding. For example, Wu, Xiang, Glen, and Duan (2008) note in the analysis of the mechanism of grinding that the balls are not the best grinding media and disadvantages include among others:• Easy over-grinding resulting from the point contact between the balls;• Attrition surface is the smallest in the grinding media;• Poor selective exposure of minerals resulting from the accidental and often significantly more powerful impact on the feed;• The grinding efficiency drops as the fineness of grind is increased;In the Handbook of mineral processing, Polkin (1950) noted that the shape of the grinding bodies determines the volume of the void spaces therein and therefore the shape affects the grinding efficiency per unit of volume of the grinding medium."

Jan 1, 2016

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By C. J. Li, J. L. Feng

In the present study we focuses on developing the poroelasticity model that deals with adsorptioninduced permeability change mostly occurred in porous media constituted several phases such as coal. The underlying pressure induced by adsorption is obtained by Virial expansion form, which is substantially founded on statistical physics. The corresponding thermodynamic pressure applying on the pore surface is then used to detail the pore pressure and further to evaluate the macroscopic volumetric strain and the porosity. In the process of physical adsorption, the adsorbed phase is in thermodynamic equilibrium with the gas phase regardless of pore size, and the corresponding chemical potentials are all equal. The relationship between surface strain and volumetric strain is derived under infinitesimal deformation conditions to gain an explicit formulation of pore surface area with respect to volumetric strain and porosity. After the formulation of surface stress modified by the Langmuir isothermal adsorption is derived, the differential micromechanical constitutive equations of porous media are obtained. By supposing that the ratio of current permeability to initial is equal to the cubic ratio of current porosity to initial porosity, the differential equations for permeability change is consequently derived. The numerical simulations by the present model for permeability change of coal induced by adsorption of CO2 and CH4, respectively, are presented under confined stress conditions. The predictions from the model are good in agreement with the experimental data of sorption-induced permeability change of coals in the literature.

Jan 1, 2015

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By K. M. Sarkar

"In many plant trial s(1,2) it has been proven that very small amounts (10 to 20 ppm) of uranium dissolved in mine water can be effectively recovered by the use of ion exchange resins and this uranium recovery has many advantages. In this paper an economic analysis at different levels of uranium contamination and at different market prices of uranium are described.For this study an operating mine-mill complex with a sulphuric acid leach circuit, followed by solvent extraction (SX) process, is considered, where contaminated mine water is available in excess of process requirements. lt is further assumed that the sulphuric acid eluant containing uranium would be mixed with the mill pregnant liquor stream that proceeds to the SX plant for final uranium recovery.Recovery by Ion ExchangeMine water, in this study, is defined as the water coming from the underground mine, or mine pits, and the run-off water from stockpiles, mine shops, crushing plant , washdown areas, etc.In nature, uranium mainly occurs in two stages; reduced (tetravalent) and oxidized (hexavalent) . The oxidation of sulphides present in the orebody often causes the presence of S04- and acidity in mine water, and this acidic water readily dissolves U+6 part of the depo sit. The react ion between hexavalent uranium, which is dissolved in water as U02+ 2 cation and S04 producing uranyl sulph ate as,"

Jan 1, 1984

By Michel Masse

1. A battery-powered wireless mesh network for dynamic diesel machinery tracking and operating status monitoring. 2. A real-time ventilation model and fan speed optimizer. 3. An OPC server for information interchange. 4. OPC linkage to existing control infrastructure. 5. A Human Machine Interface (HMI) providing data archiving, trending and reporting. 6. Live MS-Excel to interrogate the simulation, controls and optimizer. 7. The battery-powered network mesh also provides SCADA functionality to route optimized setpointsto the fans and automated regulators not linked to PLCs.

Feb 1, 2008

By Robert B. Parsons

"This article is based on a paper presented by Jim Scott at the 1988 annual convention of the Prospectors and Developers Association of Canada. The paper suggests a number of factors that might be taken into account in negotiating royalty terms.IntroductionRoyal ties are a part of mining life in Canada. They are used by many kinds of individuals in many kind s of situations. Prospectors commonly take royalty interests back when they transfer claims to development companies. Mining companies disposing of undeveloped (or sometimes even developed) properties are often paid at least in part by royalties. Royalties are even used by institutional investors with no other connection with the resource industry.Such different royalty holders have different investment goals, different cash flow requirements, and different risk / return preferences. These differences have given rise to a number of different royalty type s. These types range from the simplest cents-per-ton royalty (where the operator pays a royalty at a fixed rate per ton milled) to net smelter return or ""NSR"" royalties (where the royalty is based on a percentage of the operator's NSR) all the way to net profit interest or ""NPI"" royalties (where the royalty is based on the operator's bottom-line net profit),The fundamental difference between the many royalty types is in the risk/ return relationship. The cents-per-ton royalty, for example, is relatively risk-free. Of the many economic factors which affect a mine, the only one which will affect the royalty holder is the amount of ore physically milled. On the other hand, the potential for significant gains under a cents-per-ton royalty is also very limited. The royalty holder will not share in any increases in the market price of the end product or any cost reductions achieved by the producer."

Jan 1, 1988

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

Concentrator Improvements -1990-1995Back to Basics ?pilot plant versus plant opportunities identified ?understand process fundamentals & baseline -1996-2000Point ?C?Projects ?strategy to improve global competitiveness ?structure implemented to generate & drive ideas ?capital investment for life of mine asset renewal - 2001-200?Six Sigma Methodologies ?emphasis on data, measurements & analyses ?dedicated, highly trained personnel on projects 1990-1995 Improvement Phase??Philosophy??back to basics?approach?understand what each piece equipment needed to do?understand reagents, control variables?confirm operating strategies ??probe, stabilize, institutionalize??test theories, confirm with lab and plant trials?process stability (equipment reliability, controls)?enhanced operator guidelines, operator training?focus on continuous improvement?optimize existing equipment capability?stop looking for ?magic?solutions 1990-1995 Improvement Phase??Technical?finer grind, same equipment?optimize media size/shape to grinding application?balanced available ball mill power to applications?lowered cyclone feed densities where possible?improved selectivity, same equipment?balanced available cells to applications?streamlined process (eliminate process steps)?added cleaning stages where required?understanding pulp/mineral surface chemistry?lowered flotation pulp densities 1990-1995 Improvement Phase??Effort?numerous studies to understand process?liberation and mineralogical characterization?pulp and mineral surface chemistry?flotation kinetics and entrainment?extensive internal and external manpower?Brunswick, Noranda Technology Centre?CanMet, AMTEL, MinnovEx, Lakefield Research, McGill University?small capital expenditure

May 1, 2002

By M. B. McClenaghan

"The Ontario Geological Survey completed a regional till sampling project between 1984 and 1988 in the Black River Matheson (BRiM) area of northeastern Ontario. The project was designed to aid mineral exploration in the area by documenting the Quaternary stratigraphy and by providing a database of till geochemistry. This paper summarizes the results from the sonic overburden drilling component of the BRiM project carried out in areas of thick drift (> 5 m). Results from till sampling in areas of thinner drift (<5 m) have been presented in a separate paper. Approximately 1100 till samples were collected from 225 sonic drill holes. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically and visible gold grains were recovered by panning.Gold and other multielement geochemical data were plotted using proportional symbols to highlight anomalous areas and to demonstrate how to evaluate and interpret a very large geochemical dataset. Thresholds for identifying anomalous concentrations of Au in till samples, defined using the 95th percentile, are 1500 ppb and 12 ppb for the heavy mineral and fine fractions, respectively. The heavy mineral fraction of older ti1ls and to a lesser extent, Matheson Till, display a number of significant gold anomalies in the study area, which in a few cases, are associated with base metal anomalies. The vertical position of gold anomalies in Matheson and older ti1ls varies from directly on bedrock to several meters above the bedrock surface and can provide information of relative ice transport distances."

Jan 1, 1994

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954

By Elisabeth Kolar, Rik Catthoor, Frederik H. Kriel, Rossen Sedev, Gareth Hatch, Army Research Laboratory, Craig Priest, Scott Middlemas

"This paper reports solvent extraction of rare earth elements (REEs) carried out using a microfluidic device and considers the REE loading limit of the organic phase under laminar flow. The microfluidic device contacts aqueous and organic phase streams for a precisely defined contact time (subsecond resolution) and then separates them for offline analysis. Experiments are reported examining the effect of contact time on extraction. We focus on three REEs: one ‘light’ (Nd), one ‘mid’ (Dy), and one ‘heavy’ (Yb) REE, which are extracted using Cyanex® 572. It appears that loading limits may be locally exceeded in the organic phase near to the liquid-liquid interface, where third phase deposits are observed. Third phase formation was also observed close to the liquid-liquid interface in two-dimensional confinement, showing similar third phase adsorption on glass plates. It is also shown that, under microfluidic flow, a typical first ‘split’ between heavy REEs and light REEs can be carried out without exceeding loading limits.INTRODUCTIONMicrofluidic solvent extraction has emerged as a useful tool for studying extraction of metals in a mineral processing context (Ciceri, Mason, Harvie, Perera, & Stevens, 2013; Ciceri, Perera, & Stevens, 2011; Kriel et al., 2015; Mason, Ciceri, Harvie, Perera, & Stevens, 2013; Priest, Zhou, Klink, Sedev, & Ralston, 2012; Priest et al., 2011). The main advantages are the extremely well-defined and tunable flow behaviour, large surface-to-volume ratios, short contact times, and minimisation of sample and reagent amounts. Two main flow configurations have been studied to date: droplet-based and co-flowing streambased extraction. In the former, droplets are formed at a microchannel junction (usually a T-junction or flow-focusing junction) and flow downstream as plugs or ‘free’ droplets. In our case, stream-based extraction, the chip is a plate (often glass) with embedded microchannels (i.e. with cross-sections of tens of micrometres) that carry the aqueous and organic phases in contact without forming droplets. Thus, these chips play the role of a mixer in a conventional mixer-settler and phase separation takes place by branching the streams or collection in a vessel at the chip outlet. Stream-based extraction requires stable streams that are usually supported by a particular channel geometry (e.g. guide structure or small ‘pillars’) or surface chemistry, and flow parallel bounded by the liquid-liquid interface(Aota, Nonaka, Hibara, & Kitamori, 2006; Hibara et al., 2005; Hibara et al., 2002). Phases are disengaged downstream at a Y-junction, which is a qualitative difference between microfluidic and bulk extractions."

Jan 1, 2016

By R. N. W. DiLabio

"In a continuing program of mapping glacial dispersal trains, near-surface till samples were collected down-ice from a copper-silver-gold prospect at Onaman River, Ontario, and down-ice from the past-producing gold district at Oldham, Nova Scotia. The program is designed to aid exploration by illustrating glacial dispersal from various types of known occurrences and by identifying postglacial processes that control drift composition at a detailed scale.Native gold was mined at Oldham from arsenopyrite-bearing saddle reef quartz veins in a dome in Early Paleozoic slates of the Meguma Group. Gold abundances greater than 10 ppb in till form a dispersal train at least 1900 m long. Gold abundances between 40 and 100 ppb occur in clusters up to 600 m down-ice from gold-bearing bedrock. Anomalous arsenic abundances in till form a broad train 1100 m long that is significantly different in shape from the gold train.At Onaman River, subeconomic amounts of Cu-Ag-Au occur in quartz lenses in Archean mafic volcanic rocks. A dispersal train defined by the distribution of mineralized boulders and increased abundances of Cu, Ag and Zn in till extends 600 m down-ice from mineralized bedrock. Gold abundances between 10 and 70 ppb do not define this dispersal train, but occur instead in clusters 300 to 600 m down-ice from mineralized bedrock. In vertical sections in the upper 2 m of copper-rich till, Au abundances vary sympathetically with Ag and Cu levels; however, there seems to be no preferential site of Au enrichment in the mineral portion of the soil profile.Several of the mineralized boulders at Onaman River are richer in Au and Ag than the mineralized bedrock from which they were derived. Although some of the high Au and Ag assays were caused by biased sampling of sulphide-rich portions of the boulders, many were caused by leaching of sulphide minerals from 'the boulders, which left a limonitic boxwork that is enriched in Au and Ag. A few of the Au-rich boulders may have been derived from an unknown bedrock source."

Jan 1, 1982