Search Documents

By J. Yue

The particle breakage kinetics, product size and size distribution, as well as grinding limit for quartz suspensions in a horizontal stirred mill are investigated. Results of grinding studies on quartz suspensions in a horizontal stirred mill confirm "first-order" particle breakage rates. A comparison of equation fits reveal that the product size distribution from stirred mill is best represented by the Rosin-Rammler equation when compared to the Gaudin-Shuhmann equation, but results fit poorly as particle size below five microns. A method of determining breakage rates versus particle size is demonstrated which shows that the 10% top size fraction is most appropriate for the determination of specific breakage rates. The method is used to demonstrate the relationship between particle breakage rate and particle size. As the feed particle size becomes smaller, the size reduction ratio decreases and approaches a grinding limit which depends on the effective stresses created in the mill.

May 1, 2004

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By J. Karonen, M. Tiihonen, J. Guentner, L. Haavanlammi, Outotec GmbH, E. Kolehmainen

"Rare earth elements have obtained significant attention during the last few years due to predicted increase in their demand. Several projects worldwide are at pre-feasibility or feasibility stage aiming to commence production. Deposits of rare earth elements are typically complex and multi-metallic of nature. This means that production processes are often also complex and therefore, various metallurgical unit processes are needed. Outotec’s equipment and technology portfolio is very comprehensive and includes hydrometallurgical and pyrometallurgical apparatus and processes applicable to the efficient exploitation of rare earth deposits. Outotec has gained useful experience relevant to the processing of rare earths through several assignments including those for Alkane Resources Ltd. (Dubbo Zirconia Project), Greenland Minerals and Energy Ltd (Kvanefjeld Project), Frontier Rare Earths Limited (Zandkopsdrift project), Tantalus Rare Earths AG (Madagascar), Quest Rare Metals (Strange Lake project) and Orbite Aluminae Inc. (HPA project). The hydrometallurgical test work of two process flowsheets is presented in the paper. A roasting or acid baking step is common to several proposed rare earth projects. In the past, rotary kilns have been used, but Outotec has developed a new process concept to handle the rare earth material in fluid bed reactors. The basis for this development is long experience in fluid bed technology of Outotec in Germany. One advantage of fluid bed roasting is the higher throughput per unit. In combination with the roasting and baking, Outotec offers the gas cleaning and acid plant and provides a complete and closed concept.INTRODUCTIONRecovery of rare earth elements (REE) has obtained significant attention during recent years. It has been estimated that their demand will be boosted because of their need in many technology areas. REE can be utilized in magnets, batteries, displays, catalysts, optical devices etc. (Jordens, Cheng, & Waters, 2013; Zhang & Edwards, 2013). The production of REE is focused in China, which means that production outside of China is very scarce. However, there are multiple active development projects worldwide working towards production of REE containing products outside of China (Chen, 2011)."

Jan 1, 2016

By D. Bouchard, J. Langlais, A. Lemieux, N. Andrade

A concerted effort between Akan International Limited and the National Research Council of Canada (NRC) has been initiated to develop a liquid-based slurrymaking process, dubbed SEED (Swirled Enthalpy Equilibration Device) for semi-solid forming. The technology is presently entering the industrial and commercial stages, and will be used by the first customers at the end of 2006. Semi-solid processing of aluminium alloys offers many advantages in fabricating economically near-net-shape parts of superior quality. The SEED process helps to overcome problems experienced with thixocasting and especially the high cost of feedstock. The SEED process involves two main steps: 1) heat extraction to achieve a desired liquid/solid mixture, and 2) drainage of an excess liquid to produce a self-supporting semi-solid slug that is formed under pressure. The heat transfer plays an important role (enthalpy equilibrium) during the manufacture of the semi-solid slurry and its analysis is briefly described. The semisolid material is obtained using different processing times and initial conditions. The impact on the solid fraction distribution and the morphological evolution of the microstructure is presented. The influence of the SEED processing parameters (slurry preparation) and the resulting mechanical properties for the alloy A356 are also reported.

Jan 1, 2006

By M. Phylli Bray

"Mining has the reputation of being a very ""macho"" industry. Recently, wider educational opportunities for women in nontraditional occupations and changes in mine technology have combined to make mining a viable career choice for women also. To benefit from this new resource, the mining industry faces the challenge of developing a different work environment from the one now burdened with sexism. Management supported initiatives are needed to facilitate such a transformation. The same rethinking of gender attitudes might also be extended to mining women in their traditional role as ""wife of"". The assumption that the male worker's wife is an unpaid adjunct is being questioned. It is suggested that women's separate concerns both as helpmate and as part of the mining workforce should be considered when planning for mining into the 21st century.IntroductionI must confess that, during the preparation of this paper, there have been many moments when I questioned my temerity. After all, I am not male, I am not an engineer, and I have never had a position in mine management. But as the wife of a mining engineer and a long-time resident of Northern Ontario mining towns, I do have an interest in the mining industry. This interest has had little to do with the technical and management aspects of the industry. Instead my research has been concerned with the impact the mining industry has on the people involved, particularly women, whether directly as employees or indirectly as wives. As I look toward the 21st century, I believe that the whole question of gender relations in the mining industry is one of the critical management issues smouldering below the surface."

Jan 1, 1995

By Jan Nemcik

Among other products steel mesh has been used successfully for many years to support strata and minimise loose material from falling into the mine opening. Installation of steel mesh has proven to be difficult to automate and many other products, such as Thin Spray-on Liners (TSL), have been proposed as a replacement. Ideally, the mechanical properties of these products should be superior to those of the steel mesh, however, most TSL trialled in mines to date have been weak and in addition have had slow cure times, as a result none of these materials can seriously compete with steel mesh. Now a new polymer product that cures in seconds and forms a stiff strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong. To enable selection of a suitable polymer material for roadway skin reinforcement several numerical models were constructed to investigate the role of interface roughness and the influence of polymer stiffness on load transfer along the rock-polymer interface. Laboratory tests indicate that the shear adhesion of the rock-polymer interface can be substantial while the tensile adhesion can be much lower. The models indicate that the natural stone roughness and surface waviness plays a major role in shear adhesion while the elastic properties of polymer liner can significantly influence the polymer ability to resist fracture opening.

Oct 1, 2009

By I. Silin, M. Stapelmann, H. Wotruba, K. M. Hahn, C. Gerold, J. Katzmarzyk

New deposits are often characterized as low-grade and complex ore bodies. To date, processing of fine grained ore deposits implies complex processing routes with high energy consumption. For that reason, the investigation of dry grinding, e.g. with vertical roller mills (VRM), is an approach to save energy reserves. It is already proven that dry grinding can influence subsequent processing steps. In terms of flotation, the surface characteristics of the minerals are crucial for a successful flotation process, e.g. the sufficient adhesion of mineral particles and air bubbles. Wet grinding results in different surface properties of the product entering the conditioning stage than dry grinding, which has direct influences on the subsequent flotation process. To investigate the consequences for flotation, processing of a copper sulfide ore containing chalcopyrite and bornite was investigated, including grinding and rougher flotation. The effects of wet tumbling mill and dry VRM grinding on the degree of liberation of valuable minerals are characterized using mineral liberation analysis by scanning electron microscopy. The obtained flotation results, as well as the recorded flotation parameters such as dissolved oxygen, oxidation reduction potential and conductivity are presented and discussed. INTRODUCTION Copper production is mainly connected to porphyry copper deposits as main source for copper sulfides such as chalcopyrite and bornite. State-of-the-art processing of these deposits is already established worldwide for decades, combining crushing, fine grinding and subsequent flotation with rougher, cleaner and scavenger stages (del Villar, Desbiens, & Maldonado, Bouchard, 2010). While the demand for copper is increasing, copper grades of the deposits are decreasing and the remaining ore bodies have more complex mineralogy and finer particle size distribution. This implies processing routes with high water and – due to the liberation of fine grained valuable minerals – high energy consumption by fine grinding. One of the main energy consumers in processing plants is the grinding section, which accounts for more than 50% of the energy consumption in processing plants and even 4% of the worldwide energy consumption (Jeswiet, & Szekeres, 2016). Therefore, dry fine grinding alternatives are applied to enhance the overall energy consumption of mineral processing plants: high pressure grinding rolls (HPGR) and vertical roller mills (VRM).

Jan 1, 2019

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By P. Taskinen, A. Jokilaakso

The Flash Smelting Process for copper and nickel production has been one of the most successful new metallurgical process developments in the 20th century. The experimental data from laboratory scale investigations of studies has produced information and insight into the reaction mechanisms and kinetics of the flash reactions of copper concentrates. Advanced computer models coupling chemical reactions with a Computational Fluid Dynamics (CFD) software became possible with the development of commercial CFD software together with increased computing power. Currently, there are both experimental and CFD modelling, including also CFD–DEM coupling (Discrete Element Method), studies ongoing for investigating the kinetics of matte – slag reactions in the flash smelting furnace (FSF) settler. The ultimate goal of the modelling work is to develop a comprehensive FSF model for studying the behavior of changing raw materials, both primary and secondary, and distribution of their elements between the matte, slag, and gas phases. The use of User-Defined-Functions (UDF) is one way to digitalize metallurgical knowledge and experimental information to be used for supporting process experts and development of artificial intelligence applications in metallurgy. In this paper, a review of the development of the FSF reaction shaft modelling and experimental investigations, and the current work for the settler reactions’ experiments and modelling are presented. INTRODUCTION The Outotec Flash Smelting process (Bryk, Ryselin, Honkasalo, & Malmström 1958) has been used in the copper and nickel industry for 70 years with continuous support from experimental investigations by many research groups in academia, among others Jorgensen and Segnit (1977); Jokilaakso, Suominen, Taskinen and Lilius (1991), Chaubal and Sohn (1986), Kim and Themelis (1986), and in industry Mäkinen and Jåfs (1982); Kojo, Lahtinen and Miettinen (2009); Tuominen, Pienimäki and Fagerlund (2016). It has been developed also for pyrite and lead smelting (Asteljoki, Sulanto & Talonen, 1984). A schematic illustration of the FSF and other main parts of the process is depicted in Figure 1. Also, two and three dimensional physical water or gas models have extensively been used in product and process development (Lilja & Rajainmäki 1995). During the recent decades, computer based models have increasingly been adopted in the FSF research and development (Ahokainen & Jokilaakso, 1998); Ahokainen, Jokilaakso, Taskinen & Kytö, 2006; Hahn & Sohn, 1990; Jorgensen & Elliot, 1992; Zhou, Zhou, Chen & Mao, 2014; White, Haywood, Ranasinghe & Chen, 2015) to name a few, but also in supporting engineering and sales of the technology (Miettinen 2017). Even though the reactions of the sulfidic concentrate particles have been included in the reaction shaft modelling, the complete FSF model with both gas-solid/drop and molten slag/matte drop has so far been and still is too demanding for today’s computer hardware.

Jan 1, 2019

By F. Osmond, R. Kelly

"Malcolm Knowles, the famous adult educator once wrote: ""What a challenge we in human resources development face if we are to avoid the obsolescence of our workforce. I can foresee this challenge requiring that we reconceptualize (...) and redefine the role of HRD, away from that of managing the logistics of conducting training activities to that of managing a system of learning resources"".The context in which this was written surrounds the subject of adult education and the need for business and industry to change its approach to the treatment of adults as learners. In explaining what 'managing a system of learning resources' means, Knowles refers to line supervisors and managers as the most ubiquitous resources for day-in and day-out employee development. In many organizations training has been largely a staff rather than line responsibility. Even where trainers reported to line management, it was still seen as a staff function performed by a few specialists.This change referred to by Knowles places a much heavier responsibility on line supervisors and managers for the development of their personnel than has traditionally been the case. Managing that change - handing over the responsibility to the line organization - is the supreme challenge for the HRD function.Just why is this change necessary? Because too often, the learner does not effectively use on the job what he or she learned in the classroom. In fact, learners often discard new methods and revert to the older ways. The reason training does not stick is that the systems for training and work management are most often separate entities and while one may support the other, they need to be a single integrated system in order to ensure the transfer to the job effectiveness of training and some real value for the training dollars.Because much training can be wasted, steps have to be taken to ensure that it fulfills its intended purpose. The effective and continuing application of knowledge and skills that learners acquire can only be realized when line supervisors and managers are at the centre of the training system.This paper describes how such a systemis being developed at the Iron Ore Company of Canada (IOC) as a functional training program is introduced. The following text provides background information on the IOC - who they are and where they are located, a definition of functional training, an evaluation of the suitability of this approach for adults in industry, a description of how the program is being implemented at IOC and some observations that have been made as this change is experienced."

Jan 1, 1995

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

By M Reza Afshar

In this work a mathematical model was developed to study the effect of electromagnetic force on the magnesium melt containing nonmetallic inclusion in an electrical isolated channel. The electromagnetic force exerted on the inclusion induced by DC current field was calculated. A three dimensional turbulent flow equations were solved numerically to compute the velocity field within the channel. On the basis of computed velocity and magnetic fields, the trajectories of inclusions were calculated using the equations of motion for inclusions. Parametric studies were carried out to evaluate the effect of various parameters such as current density, channel diameter and particle density on the removal efficiency of inclusions from magnesium melts.

Jan 1, 2004

By L. I. Kiss, S. Perron, S. Poncsák, A. Perron

Aluminium industry has an increasing interest in the diminution of the energy consumption of the Hall-Heroult process by the reduction of the anode bottom covering with gas. Electrically isolating carbon-dioxide bubbles, produced at the anode, increase the ohmic resistance of the cell. As the gas production rate is determined by the applied current density, anode covering can be decreased only by a faster evacuation of the gas from the inter-electrode space. Among others, the inclination and curvature of the anode bottom promotes the release of the bubbles and thus decreases the mean value of the covering. Indeed, anode, insert in the molten cryolite bath has a square shape with horizontal bottom. However, inhomogeneous anode consumption, electro-erosion, bath circulation and the inclination of the bath-metal interface modify this shape gradually during electrolysis. Anode bottoms become inclined with rounded comers. This concentrates the gas generation to the center zone of the anode. As the bubble layer cannot be observed directly because of the hostile environment and the opacity of the bath, real scale air-water systems are used to study the impact of the anode geometry on the anode covering and the bubble induced flow. However, the physical properties of such a system are different than that we can found in the real cells. A simulator using the Lagrangian description of the bubble layer has been built and presented in earlier papers. This tool was used to investigate the effect of the anode inclination on gas covering and bath velocity, for both C02-cryolite and air-water system. Results obtained for the second system were compared to experimental data .

Jan 1, 2006

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By M. Takebayashi, M. Shingu, H. Nagai, T. Nakai, S. Asano

The Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. (SMM) is located in the coastal zone of Saijo City and Niihama City, Ehime Prefecture, Japan. The refinery has been producing copper, sulfuric acid, and precious metals such as gold, silver, and PGMs. Previously, the process of precious metals recovery was a combination of pyrometallurgy and an electro-refining process with the conventional cupellation for around 400 years. However, this process had some major problems such as non-efficient recovery of valuable metals, high environmental risk by pyrometallurgy, high cost for maintenance of equipment and so on. In order to solve these problems, a thorough hydrometallurgical process for precious metals refining using chlorine leaching technology was originated and developed by Sumitomo and thereafter commercialized in 2004 at Toyo Copper Smelter and Refinery. This new process enabled shorter-term recovery of gold and manpower saving, and occupational safety and working conditions have also been improved. Superiority over the existing hydrometallurgical processes was also confirmed, for example by the achievement of 99.99% pure silver production without an electro-refining process. This paper summarizes the hydrometallurgical technologies for precious metals recovery such as chlorine leaching of copper anode slime for silver recovery, solvent extraction (SX) for gold recovery, and ion exchange (IX) for PGMs recovery. It also presents a unique silver purification process. INTRODUCTION Sumitomo Metal Mining Co., Ltd. (SMM) produces copper, precious metals and rare metals as by-products at the Toyo Copper Smelter and Refinery, and nickel and cobalt at the Niihama Nickel Refinery. Precious metals contained in nickel ore are also separated and refined at the Toyo Refinery after concentration. SMM has been refining precious metals using the pyrometallurgical method. In recent years, we have revamped the separation and refining process of precious metals dramatically by making use of advanced hydrometallurgical and engineering technology developed in the company. In this paper, we introduce the history of development and techniques of this process, and also introduce in detail the technologies of gold refining, PGMs recovery, selenium recovery, and silver refining which have been particularly difficult to achieve.

Jan 1, 2019

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By Simon C. Dominy

"There are two main issues stemming from Vallée’s (2002) comments on Dominy et al. (2001b). First, he raises the importance of quality assurance/quality control (QA/QC) during resource estimation programs, and second, he indicates that the resolution and understanding of continuity (grade and geological) issues are paramount in the classification of resources. In particular, continuity is critical at the boundary between the Inferred and Indicated Mineral Resource categories. The original contribution agrees with the importance of these points, and the principal author offers the following discussion and clarification. Further comment is also provided on the reporting of grade uncertainty through grade ranges.It is worth remembering that vein-gold deposits (e.g., shear-zone, lode-gold, mesothermal types etc.), particularly those containing coarse gold particles (e.g., >100 µm), generally show large variations in grade and an erratic grade distribution. In most cases, diamond drilling is a good measure of geological continuity (depending on drill spacing), but a poor measure of grade and its distribution. High-nugget effect deposits rank among the most difficult deposit types in terms of producing an accurate and precise resource estimate, and clearly represent a distinct deposit type."

Jan 1, 2002

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016