Search Documents

By Roger St. C. Smart, Paul Weber, Joan E. Thomas, William M. Skinner, Warwick Stewart, Stuart Miller

For mine sites affected by acid rock drainage (ARD) or with a potential future ARD issue, the prime consideration is not only the classification of different waste rock as potentially acid forming or non acid forming but also the peak acid (and metal) release rates and expected ARD duration during which effective ARD management and acid neutralisation capacity (ANC) are required. Methods for assessment of this ANC (e.g., Sobek tests) are already available but can be unreliable in ARD containing significant proportions of framboidal pyrite or iron carbonates. The measurement of negative ANC values and the release of S to solution showed that significant sulfide oxidation may occur prior to and during testing in samples containing reactive (particularly framboidal) pyrite resulting in serious underestimation of the original ANC. A simple methodology with dissolution in Ar-purged water before ANC testing, removing ferrous salts, and sulfate assay after ANC testing corrects these effects. Results also showed that a significant lag period (up to 432 h) may be needed for complete hydrolysis of Fe associated with the standard Sobek ANC testing of, for instance, siderite. Hence, the ANC of iron carbonates is usually significantly overestimated. By filtering and the addition of H202 until there was no subsequent pH drop (due to Fe hydrolysis reactions), followed by back titration to pH 7.0, the ANC for siderite was similar to the ANC determined after 432 h lag by the Modified Sobek ANC test and to the mineralogical carbonate ANCcarb determined by calculation based on electron probe micro-analysis. A chemical ANC calculation, based on neutralising cations released to solution, has provided a method to quantify the short-term ANC of carbonates and silicates in simple mixed mineral assemblages and waste rock samples. Results showed that silicate ANC can be more important in short-term neutralisation than carbonate ANC in low carbonate samples. In the longer-term, decreasing sulfate and metal loads with increasing pH values suggests that eventually sulfide acidity generation rates will match the longer-term inherent acid neutralisation rates of the sample derived from silicates. A kinetic ANC measurement for silicates, after steady state dissolution is reached, that indicates the number of hydrogen ions neutralised/m2/yr has been developed. These values can be used in estimates of the net acid production profile from wastes with low (and decreasing) pyrite content after the short-term ANC is exhausted.

Jan 1, 2004

By D. G. Dixon

A novel technology for leaching copper from primary copper concentrates has been developed at UBC. This patented technology takes advantage of the galvanic couple between pyrite and chalcopyrite to ensure rapid and complete oxidation of chalcopyrite under mild conditions in acidic iron sulfate solution, without the need for microbes, ultrafine grinding, or chemical additives such as chloride, nitrate, or surfactants. Copper recoveries of 98% or greater can be achieved at 80°C under atmospheric conditions in as little as 4 hours of residence time. The process is selective for chalcopyrite over pyrite, generates near-quantitative levels of elemental sulfur, and is fully compatible with conventional solvent extraction and electrowinning of LME Grade A copper cathodes. In this paper, the fundamentals of the Galvanox ? process are reviewed, and selected results of batch leaching tests on various concentrate samples are presented and discussed.

Jan 1, 2007

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

By Jonathan Tsang, Ali Merati, Jonathan Beddoes

Due to economic factors, many aircraft in service today have been operating for more than 30 years even though they were initially designed with a service life of 20 years. Improved damage management models are therefore needed for use in life prediction and management of the aging fleets of aircraft. Currently, the generally accepted procedure in fatigue life prediction methodologies is to back calculate the equivalent initial flaw size (EIFS) using established long crack growth data. However, it was observed from studies carried out at the National Research Council Canada that nucleation and short crack growth constitute up to -95% of the fatigue life. As a result, it seems that the significance of the short crack regime has been underestimated and must be further investigated and fully understood before an accurate holistic life prediction methodology can be realized. Unlike long cracks, local microstructural features such as grain boundary, grain size, inter-particle spacing, and texture play dominant roles in the behavior of short cracks. An extensive study has been carried out to evaluate different crack detection and monitoring techniques in the short crack regime for AA2024-T3. The results will be presented in detail.

Jan 1, 2004

By S. Brophy

Controlled Short Circuit ? Metal Inert Gas (CSC-MIG) welding is a process that can be referred as a "Cold Welding" technology. The CSC process is based on accurate control of the welding wire position, thus the mandatory requirement for the automation of the process. One of the main advantages of the CSC-MIG process is the rapid solidification of the deposited material, resulting in weldments displaying low porosity contents, and enabling the joining of thin sheet materials. These characteristics render this process an ideal one for freeforming of components, where rapid solidification would be efficacious. This presentation will focus on the progress made towards the freeforming of Al-based components in the NAIN laboratory at McGill University. The relationship between the filler metal used, freeforming (deposition) parameters, resulting microstructure and mechanical properties will be presented.

Jan 1, 2011

By Lou Covello

Bow Valley Industries Limited i conducting an on-going exploration program for gold in Archean, turbidite-hosted iron formations near the Lupin mine on Contwoyto Lake, orthwe t Territorie . Exploration philosophy and practice are modelled on the Lupin deposit where 70% of the gold occurs within laminated pyrrhotitechert. sulphide facie iron formation. Thi i intimately associated with barren to low-grade silicate facie iron formation which i enclosed by predominantly argillaceou meta ediment . This type of mineralization i amenable to exploration through an integrated program of geological and geophy ical surveying, consisting of the following: i) Geological urvey both regional and local to outline area of turbidites and a ociated iron formation. Structural and tratigraphic trends documented during this phase are useful in determining eventual grid configurations. Grids are then mapped and ampled at 1:2000 cale. ii) Magnetometer and gradiometer urvey at the ame scale define strongly magnetic diabase dyke and erratically magnetic portions of iron formation. iii) VLF-EM survey are u eful in outlining conductive trend invariably as ociated with sulphidic or graphitic phase of iron formation. iv) Geological updating and ampling of iron fom1ation based on the geophysical su rveys. This is necessary for the production of a final geologic map and a an adjunct to drill target election. In problematic instances self-potential urveys have documented the pre ence of non-conductive sulphide accumulations, and horizontal loop EM surveys have been used to determine conductor geometry and quality. Target selection is based on a synthesis of the information from all of the above surveys with the results of no single survey being critical to drill decisions. The program is designed to provide first-pass, detailed , cost-effective ground coverage of large areas of highly prospective geology.

Jan 1, 1986

By C. Kuehmann, B. Tufts

QuesTek Innovations has applied its Materials by Design® methodology to computationally design a new ultra high-strength corrosion resistant steel. Ferriurn® S53 eliminates the need for toxic cadmium coatings currently used on conventional steels in landing gear systems. S53 has the strength of 300M steel, and corrosion resistance similar to 15-5PH stainless steel. S53's corrosion resistance improves stress corrosion cracking resistance and reduces susceptibility to hydrogen embrittlement, improving component reliability and providing an opportunity for extended overhaul and repair intervals. Ultimate tensile stress is 1965 to 2000MPa. S53 was designed to be mechanically equivalent to 300M, with the key addition of intrinsic corrosion resistance. Alloy design, microstructural characterization, and mechanical properties are discussed herein.

Jan 1, 2006

By Chigova. Terence

In 2008, Anglo installed the Modular IntelliMine® System at its Kleinkopje Mine (AKK). As part of this deployment, Anglo also used the Change Management Consulting Service offered by Modular to ensure a successful installation. This paper outlines the benefits that AKK has realized through the deployment of the system, including a 15% improvement in tonne/kilometers per hour (TKPH). The mine benefited from the improvements provided by the system almost immediately by utilizing change management to more effectively integrate IntelliMine technology into their processes. This case study includes details about the deployed system, the implementation of change management, and recommendations to ensure success in future projects.

May 1, 2010

By M. H. Allan

SASKATCHEWAN POWER CORPORATION is a Provincial Crown Corporation responsible for the production transmission and distribution of electric power and natural gas in the Province of Saskatchewan. Through the electric power responsibility, we became interested in the coal reserves in Saskatchewan, which, although still somewhat of an "orphan fuel" in the early and mid 1950's, gave the promise of providing a low-cost source of energy for electric generation. Coal in Saskatchewan, a lignite with an "as-received" heating value of from 5000 to 6500 Btu's per lb and up to 40% moisture, was first recorded in 1853 . By the end of the 19th century, many small mines were in operation in the Estevan, Coronach and Shaunavon areas supplying local inhabitants with a cheap source of heat. These small mines, some of them prosperous, some of them not, continued operation right up to the late 1940's, when oil replaced coal in the market place. The year 1930, however, saw the introduction of the new technique of strip mining in the Estevan area. This technique revolutionized coal mining. It was now possible to use large machinery to uncover the coal and cast the overburden to one side instead of burrowing through thin seams of coal varying from 2 to 10 feet thick. The overburden cast aside by these large mechanical shovels, or later draglines, created heaps of spoil which at that time, during the depression, were a sure sign of prosperity and the welcome news that people had jobs. By the late 1940's, coal production had dropped off, but the spoil piles remained and were now labelled by some as "scars on the landscape", even though there had been some natural succession of grasses. In addition, some people had planted trees in experimental plots and even some aerial seeding had been done.

Jan 1, 1978

By Laxman (Lucky) Amaratunga, Hisham Madi

Final disposal of mine wastewater neutralization sludge continues to be one of more pressing problems in the mining industry. The disposal of mining and metallurgical waste products into underground reduces the environment impact and improves the safety of the mining operation and the economics of the enterprise. This current research focuses on an investigation of utilization of mine wastewater neutralization sludge obtained from Kidd Creek Mine site, as a supplementary material for their proposed deep mine pastefill system. Their proposed pastefill consist of combination of rock aggregate in a matrix of imported sand and tailings with binder (Portland cement + Slag cement). Pastefill mixes containing various percentages of the waste sludge 0 (control mix), 1, 2, 3, and 5% by weight as replacement to the fine sand were prepared and tested with different percentages of binder. Hypothesis behind this approach is to study the behavior of sludge as replacement of sand in matrix as well as its ability to act as a binder. Compressive strength, percentage of sludge, binder dosage, slump, water to cement ratio, percentage of solid, and curing time are being observed. The results indicated that sludge can be incorporated into the pastefill and enhance its strength without compromising the pastefill quality and integrity.

Jan 1, 2004

By Ferenc Molnár, David H. Watkinson

Abstract - Cu-Ni-PGE footwall ore deposits were studied in the McCreedy East and Whistle mines along the North Range, and the Lindsley and Little Stobie mines along the South Range of the Sudbury Igneous Complex. The footwall ores in these localities differ from typical magmatic Fe-Ni-Cu- PGE deposits in the Sudbury mining camp: they have higher Cu/Ni ratios, higher PGE content, veinlike appearance and ubiquitous association of ore with hydrous silicates. Results of comparative fluid inclusion petrography and microthermometry of footwall ores indicate that high temperatures (300°C to 480°C) and heavy-metal rich saline (up to about 40 NaCl equivalent wt% salinity) fluids were associated with the formation of the PGE-rich footwall ores at moderately high pressures (around 2 kbars). However, several, possibly independent fluid circulation stages were also found at the different localities and there also are differences in detailed characteristics for ore-forming fluids especially comparing data from the North Range and the South Range. Thus, in addition to the high temperature and salinity of fluids, there are local variations in the nature of hydrothermal processes. These differences may be related to the diverse origin of fluids (magmatic, metamorphic, and formational brines) and their differing extents of interaction with the compositionally different footwall lithologies.

Jan 1, 2001

By D. L. Johnston

"The avenues and degree of participation by aboriginals in the Canadian minerals industry have changed significantly during the thirty years of the author's career in that industry.The typical 1950s cycle of mineral industry involvement of a local non-Europeanized aboriginal was as an individual employee. The employment relationship would begin with the best of intentions by both parties of permanence and terminate when the pioneering employee was unable to reconcile the attendance behaviour required by the employer and the social-sharing behaviour demanded by family and friends.Cominco Ltd. has been a mine operator and developer in the North since the 1920s. Cominco's early experiences with employment of non-Europeanized natives at the Con Mine in Yellowknife, Northwest Territories from 1938 to 1986 was a negative experience from both the employee and employer ends. A series of classic failures in employment of individual aboriginals was a large part of the history. A few Metis or natives from other areas were the permanent aboriginal employees at Con (2010). Racial prejudice was overt on the street in Yellowknife and, it can be assumed, in the workplace, as well.The history of aboriginal employment at the Pine Point, Northwest Territories operation (1964 to 1988) was somewhat better but also frustrating. The mine was equidistant (80 km) from the Dene communities of the Hay River Indian Reserve and Fort Resolution, both on Great Slave Lake. Despite a large aboriginal presence and many well-intentioned efforts, employment of aboriginals at Pine Point never got much beyond ten per cent. These would have been half local and half northern prairie aboriginals. One continuing success story was the railcar loading and covering crew led by Ed McKay, a local aboriginal. This predominantly aboriginal crew did its own recruiting and several are on Cominco pension."

Jan 1, 1995

By D. Harris, G. Ye, G. Oprea, J. Rigby, T. Troczynski

Sintering and ceramic bonding in refractory castables take place mainly in the binding system during the first heat-up and in service. Consequently the strength and the corrosion resistance of the hot face layer depend on the sintering ability of the complex mix of ceramic powders constituting the binding system. As a result, the use of nano- sized reactive powders in the binding system mixes would activate the sintering and enhance the ceramic matrix formation at temperatures below 1300°C. Our work presents the experimental data on sintering behavior of binding systems containing magnesium aluminate and alumina nano-powders in the temperature range of 800-1450°C. The results indicated that a ceramic matrix, similar to high temperature fired bricks, could be generated after firing at the relatively low temperatures available in the non-ferrous smelting furnaces.

Jan 1, 2004

By Y. Hanada

Electrorefining at higher current density is desirable due to the increase in productivity attained without expanding the plant size. However, increasing the current density in common commercial practice causes problems such as anode passivation, dendritic deposition, cathode impurities and energy consumption. In general, agitation of the electrolyte is effective in suppressing these problems. To apply the agitation to commercial practice effectively, the method of agitation is important. One possible method is agitation by gas injection. In this study, fluid motion characteristics with gas injection between electrodes were investigated using a water model. Flow patterns were observed and fluid velocity was measured using a particle tracking method. It was found that the time-averaged velocity near the electrode walls was of the order of 0.1 m/s in the conditions. The flow was highly turbulent. The turbulent component of velocity was the same order as the time-averaged velocity. The mass transfer coefficient between the wall and fluid doubled when the effect of turbulent intensity was taken into account. The effects of gas injection on the electrolysis behaviour at high current density were discussed in terms of the mass transfer. It is suggested that gas injection could suppress the problems at high current density.

Jan 1, 2007

By Takahiko Okura, Chiharu Tokoro, Shunta Shibuya

Copper concentrates bearing arsenic as enargite (Cu3AsS4) or tennantite (Cu12As4S13) have disadvantage on copper smelting environmentally and economically, so those concentrates should be treated decently. In this paper, some experiments of arsenic removal from several kinds of copper concentrates by heat treatment in an inert atmosphere were discussed. In this study, several samples in which arsenic contents varied 0.18 to 8.3 wt % were heated to the temperature range of 400 °C to 700 °C under argon gas flow during 1 hour. The heat residues and volatilized materials (V.M.) were analyzed by XRD, XRF, ICP-AES, XAFS and MLA to analyze residual concentration of arsenic and residual mineral composition. Experimental results showed that arsenic removal from copper concentrates advanced in 2 steps; at the temperature range of 500 ° C to 550 °C and of 550 °C to 650 °C, respectively. MLA analysis showed that a few of arsenic in enargite was removed by 550 °C heating and a majority of it was still combined with copper and sulfur as tennantite. On the other hand, arsenic in tennantite was removed almost completely by 650 °C heating. Furthermore, a particular type of arsenic mineral, such as Cobaltite (CoAsS) still remained after heating at 700 °C.

Jan 1, 2014

By Jamel Sgaoula

During 1998 COGEMA Resources Inc. announced that operations at the Cluff Lake mine will be suspended indefinitely by the end of year 2000 as a result of deteriorating uranium market conditions. To remain profitable, Cluff Lake mine started an aggressive cost reduction program. A cost reduction team was formed to look for ways to lower production costs. The focus of this team was to screen all areas and to come up with ideas to improve the economy of the mine and ensure the viability of the operations over the remaining three years of operations. Among the areas where significant savings were achieved are: (1) replacement of portion of cement with fly ash in backfill; (2) backfill optimization; and (3) new shotcrete plant installation on site for bulk in-house shotcrete production. This paper details the research work carried out by Cluff Lake mine on these projects and results of its application.

May 1, 2001

By Kernaghan Webb

Organization of Presentation ?Genesis, Premise, Hypothesis ?Background ?Methodology ?Key research questions ?Research Team to Study Kinross Maricunga ?Research Milestones ?Chilean context ?Chilean Legal Framework ?Kinross Gold the basics, CR approach, Maricunga ?Issues, Perspectives ?Concluding remarks

May 1, 2010

By Xiaoxing Hu, Guibing Zheng, Yangge Zhu, Xingrong Zhang

"In China, more than 90 percent of titanium resources are reserved in vanadic titano-magnetite deposits. In this type of ore, the same elements such as Ti, Fe, Ca, Mg exist on surface of both ilmenite and titanaugite (the gangue mineral) because of isomorphism, which makes selective flotation difficult. Therefore, how to enlarge the floatability difference between these two minerals has always been a research emphasis and still needs to be studied further. In this paper, the pre-treatment methods using ultrasonic wave were proposed. The results indicate that ultrasonic treatment shows beneficial effect to enlarge the floatability difference, and the effect will be strengthened by extending the ultrasonic treatment time or increasing the ultrasonic power. The mechanism was investigated through infrared spectroscopic (FT-IR) analysis. Collector interacts with Ca and Mg which results in titanaugite flotation, after ultrasonic treatment, the dissolution of Ca and Mg is intensified, which leads to the lack of active points on mineral surface, so the floatability of titanaugite is depressed. Meanwhile, collector mainly interacts with Fe which results in ilmenite flotation, and the present of ultrasonic might promote its oxidation (Fe2+ to Fe3+), so the floatability of ilmenite after sonication is increased.INTRODUCTIONUltrasonic is the sound wave with frequency of 2 × 10-4 Hz~2 × 10-9Hz. Since the first International Symposium of Sonochemistry in 1986, the application of ultrasonic wave is more and more extensive. In researches about mining and metallurgy, various investigators have shown that intensive acoustic fields can modify the state of a mineral, leading to chemical or dispersive effects. Generally, the effect of ultrasonic vibration depends upon the nature of the mineral and also the way ultrasonic wave is applied (Celik, 1989; Ozkan, 2002). In addition, ultrasonic treatment usually plays roles of removal of reagents adsorbed layer from minerals and emulsification of flotation reagents when it is used in flotation (Nicol, Engel, & Teh, 1986; Slaczka, 1987; Djendova & Mehandj, 1992; Farmer, Collings, & Jameson, 2000; Gurpinar, Sonmez, & Bozkurt, 2004)."

Jan 1, 2016

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007