Search Documents

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974

By G. W. H. Norman

INTEREST in the mineral possibilities (gold, copper) of northern Quebec, north of the Quebec-Cochrane branch of the Canadian National railway, has centred for many years in the Chibougamau district (see Figure 1). Since 1934, however, promising gold discoveries in the Rose Lake-Florence River section, 115 miles southwest of Chibougamau lake, have widened the interest, and prospectors have examined other parts of the country between Chibougamau lake and Bell river and the surrounding districts. The object of this paper is to !resent an outline of the geology, and to describe the mineral deposits, o part of this region, or, more specifically, of the part embraced by the Opawica-Chibougamau and Waswanipi map-areas(l), which include the districts about Chibougamau lake and Rose lake-Florence river, where mineral deposits are now in course of development either by surface or underground work. Early discoveries, developments, and explorations in the Chibougamau district are well summarized in the report of the Chibougamau Commission, published in 1911(2). The Commission discredited previous optimistic accounts of mineral discoveries in the area, made initially in 1903, but at the same time they expressed the opinion that, from a geological standpoint, the district promised a reward to diligent and intelligent prospecting. Their general conclusion-that prospecting in the area was not then (1911) commercially advisable in view of its inaccessibility and other handicaps shifted interest from the district until, some years later, valuable discoveries were made in the Rouyn area, and aircraft widened the field of successful exploration. During the past ten years or so, considerable energy has been spent in promoting the development of the district. The net result has been the discovery of a number of prospects, the majority of which have been explored only by trenching and, in most cases, diamond drilling.

Jan 1, 1936

By E. M. Yates, H. M. Hamilton

"For the assent of any new mining project it is essential to determine a realistic value of revenue from the sale of concentrates.A description of the market factors influencing the concentrate terms will be presented along with a detailed review of historical terms of a smelter contract for zinc concentrates. OverviewFor the assessment of any new mining project it is essential todetermine a realistic value of revenue from the sale of concentrates.This applies at all stages of assessment through to the final feasibilitystudy. In forecasting revenue for a zinc mine the followingfactors must be considered:(a) mill recovery and zinc concentrate grade;(b) metal price forecast for all payable metals;(c) smelter terms; and(d) other selling costs.Normally, data from test work are used to determine mill recovery and concentrate grade.Market forecasting, and indeed all economic prediction is an inexact science and probably will always remain so. We have our econometric models our input/output models and a lot of other tools. But they are of no help in predicting the unpredictable. OPEC's huge increase in the price of oil was certainly the most dramatic example of this. It had a tremendous effect on the cost of producing most products world wide and on the price of these products. Any forecasts made prior to the OPEC action were obviously proven wrong."

Jan 1, 1994

By Leonard A. Wolff

"The 1980sfor the mining industry can be characterized as the survival of the fittest. High interest rates, low commodity prices, foreign subsidized competition and decreasing ore grades have contributed to a streamlining of the domestic mining industry in the United States, leading to the shutdown of operations or large cutback of work forces. The purpose of this paper is to look at the impact of a layoff on the employees of what was once a major uranium producer in south central Wyoming, twenty months after the final layoff and mine shutdown. INTRODUCTIONDecember 19, 1985, was the date of the final of three successive layoffs over a two-month period, leading to the complete shutdown of Petrotomics Company, a subsidiary of Getty Minerals Company. The final shutdown was due to a combination of depressed U3O8 prices and the takeover of Getty Oil Company by Texaco in January 1984.The layoffs affected 104 employees and included mine personnel, mill personnel and staff. Both hourly and salary workers were involved. The operation was considered non-union, however, a few mill hourly employees were unionized. At the completion of the layoffs. only a handful of employees remained for administrative and miscellaneous functions.For Getty employees, the terms of the merger agreement provided a generous level of separation benefits. The terms that were insisted upon by Mr. Petersen, Chairman of the Board for Getty Oil, stipulated that employees receive one month of severance pay, for each full calendar year of employment up to a maximum of two year's pay. This was the forerunner of what is now commonly known as the ""tin parachute”. All but the union employees of Petrotomics received these separation benefits. Union employees were covered by their separate, less generous, contract.Much of the literature that has been published in recent months has centred around the effects of layoffs on remaining employees, or the psychological effects on the severed employee. This study will emphasize the economic impact and ramifications due to a layoff, using the Petrotomics employees as a case example."

Jan 1, 1989

By T. A. Postolski, A. J. Sinclair

"Abstract- Two examples are used to describe how geological features impact on the development of semi-variogram models to be used for geostatistical resource/reserve estimation of porphyry-type deposits. In the Main zone of the Huckleberry porphyry copper deposit, mineralization is concentrated in fracture zones localized in volcanic rocks, along the eastern and southern margins of a granitic stock. Mineralized volcanic rocks can be subdivided into three separate domains, each with its own preferred direction of mineralization that is reflected in contoured Cu diagrams and semivariograms.The East zone at Huckleberry deposit, spatially distinct from the Main zone, is controlled by a fracture zone elongate roughly east-westerly and bounded on the south by a major fault (easterly striking and steeply dipping) across which there is a dramatic drop in grades. The eastern part of the East zone appears to be coaxial with a large intrusive body; the western part contains a small, elongate dike-like intrusion. Contoured Cu values for many levels suggest that the principal direction of geological elongation of the east and west domains of the East zone differs significantly. Independently derived semi-variogram models for each domain are different and reflect this difference in trend.In both Main and East zones of the Huckleberry deposit, block estimates by ordinary kriging are significantly different using a domain-specific semi-variogram model than using a deposit-general semi-variogram model. The domain-specific estimates are deemed better because they are based on local controls of mineralization and have less conditional bias than those generated by the depositgeneral semi-variogram model."

Jan 1, 1998

Superconductivity, New Mexico and Mining? ? High Temperature Superconducting cables made from ?nickel tape? ? Testing on U.S. power grid ? 25 year time horizon Purpose Create awareness about the successful application of energy management systems at a Northern Ontario mine site.

May 1, 2008

By Denni Nikols

"Planning for coal beneficiation in the electric utility industry is relatively complex, involving the coordination of experts and specialists in a broad range of fields, as well as compliance with a wide variety of government regulations.This paper examines the role of the planner, reviews possible benefits of coal beneficiation, identifies potential problems and illustrates a typical planning schedule.The steps involved in the planning process are:Step I-Bench- and pilot- washability studyStep 2- Wash plant designStep 3- Power plant and boiler designStep 4-Mine designStep 5-Major environmental and technical problems to address.IntroductionElectrical utilities and coal have a long and intimate relationship . Cleaned coal is becoming an increasingly popular fuel with the utilities for a variety of reasons. Generally, the greatest impetus to burn a cleaned or prepared coal fuel comes from the need to control airborne pollutants.Long-range planning is a standard practice for electric utilities, forecasts of demand must be made well into the future. Since the lead time required to provide new facilities is often as long as 10 years and the cost very high , planning becomes an important task.For a utility that owns and directs the operation of its coal mines, the mine planning or fuel acquisition planning takes on the magnitude of other corporate planning functions. It is from this perspective that a utility would view coal preparation. Except for the interaction of a coal-fi red plant on the actual mine design the planning considerations o f a beneficiating facility for a captive mine or a contract raw coal supply are about the same. Because TransAlta Utilities is currently supplied from captive mines, this discussion will tend to focus in that direction.It is the role of a planner to plan. This is easy to say but it is not always easy to do. Often we are working within a context that resembles the geological time scale. Frequently the objectives are not clearly defined when we begin and ultimately our plans are tested in the waters of government regulations and cost benefit analyses .Planning for beneficiation of Plains coal, or any coal, provides just such a test. The planner's role in this endeavour requires a wide vision. While parts of the process may be amenable to classical methods of project scheduling, the broad range of subjects and interaction of seemingly unrelated tasks is sure to obscure some of the considerations that must be made. Therefore, the planner's chief role is coordinating the work of many experts and specialists toward the final objective.Among the specialists are combustion , geo technical, mining, civil , and mineral processing engineers , geologists, hydrogeologists, soil, and reclamation experts to list a few.When one considers coal beneficiation, the planning part o f that consideration is probably more complex than any other single engineering function. Due to the company's location in the Alberta Plains and the proximity o f the mine to the thermal generating station, this paper will tend to emphasize that situation.Beneficiation may offer some advantages over run-of-mine coal to the power plant opeator. Some of these advantages are: removal of a contaminant, power plant efficiency gains , lower plant capital costs (for new plants), possible lower mining costs."

Jan 1, 1984

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By Somchet Vongpaisal

This paper presents the R&D results on the development of a new knowledge-based system for predicting stope instability and associated unplanned dilution in deep underground mining operations. A new prototype was developed based on databases generated from 3D non-linear elasto-plastic finite element stress analysis, heuristic rules, and case histories. This prototype aims to assist mine operators to make decisions on strategic mine planning and feasibility in a quick and efficient manner thereby minimizing risk on ground failure and optimizing mining costs.

Jun 1, 2012

By Jacek Paraszczak

As the deposits located closer to the surface are getting depleted, more and more Canadian mines produce ore from considerable depths. Deep mining represents a number of serious challenges including high rock temperature. Conventional diesel powered loadhaul- dump machines and trucks so widely used in metal mines constitute an additional source of heat and noxious gases. Due to this, they have a substantial adverse impact on a quantity of fresh air required and a cost of ventilation, particularly since the mines have to meet more and more stringent regulations in this respect. In this context, the paper examines possible alternatives for diesel powered equipment, both these commercially available as those at the stages of prototypes or under development. They are reviewed with regards to their principles, required infrastructure, stage of technology development and its progress. The questions of their flexibility, practicality and economic viability are also addressed. Following the above a potential for their implementation and possible benefits (if any) in the conditions of deep Canadian mines is discussed. The paper concludes with short to medium term predictions concerning the most promising drive alternatives for vehicles destined to operate in deep metal mines.

Feb 1, 2008

By S. Kaushik

The control room in a mineral processing plant has become increasingly complicated with complex unit operations coupled with rapidly evolving systems of sensors and control. Even with significant automation, human intervention is required to counter various scenarios that play out every day. A typical control room operator must monitor over 300 individual points of data in order to ensure the safe and efficient operation of the plant. At the same time, the experience of the workforce is decreasing as operators retire and the new generation enters the concentrators. Global competition for skilled operators continues to be strong and the opportunity to apprentice has diminished. The challenge is to provide a skill foundation for the operators so that they can be effective in the concentrator in a timely and safe manner. Progressively, the industry is turning to dynamic simulation tied into the control system. The simulator environment operates behind the control system to emulate the plant operation, reacting as the plant would when a change is made. The operator drives the process, with realistic feedback, which enables learning in a safe environment. This paper will take the reader through a green-field case study and discuss the effectiveness of integrating an operator training simulator (OTS) on the operator’s learning curve.

Jan 1, 2014

By Robert B. Parsons

"There is a widespread concern that certain of Finance Minister Michael Wilson's Tax Reform proposals will likely lead to a significant decline in flow through funding after 1988. This does not bode well for the junior exploration sector, which relies heavily on flow-through to finance exploration programs. The exploration industry is actively pursuing various solutions to the problems posed by Tax Reform, in order to ensure that flow-through has a future.IntroductionWhile the proposals contained in Finance Minister Michael Wilson's Tax Reform White Paper may not be as far-reaching as some people had expected, nevertheless the combination of the existing tax rules and proposed new rules offers sufficient complexity to keep pencils sharpened for many months. After having had an opportunity to study Tax Reform since June 18, 1987, the sharpened pencils are suggesting that the White Paper is not without its shortcomings and pitfalls. Insofar as the mineral exploration industry is affected, there is widespread concern that adoption of certain Tax Reform proposals could spell near disaster for mineral exploration in Canada. More specifically, there seems to be a consensus among the industry, as well as some federal and provincial government officials, that the announced phase-out of the ""mining exploration depletion allowance"" (MEDA) would reduce the appeal of flow-through shares to the point where only a fraction of exploration funding would be financed in the future by flow-through."

Jan 1, 1987

By Peter Babik

"Cable TV networks are extensively used throughout Canada for TV signal distribution. Mobile/portable radio communications are also used extensively throughout all sectors of industry. There are numerous manufacturer supplying these industries with a wide variety of equipment and accessories.IAL's underground radio communications system combines the techniques of cable TV and mobile radio to produce a flexible communications system with most of the advantages of both systems. Standard off-the-shelf mobile, portable, base-station and repeater equipment can be used. The equipment may need modification to be customized to particular end user requirements, but does not require a complete new unit redesign. Likewise, the cable TV distribution equipment is off the-shelf, with some items requiring modification for underground system application.Radio communications can be provided wherever the cable system is extended. Where traffic or type of activity warrants it, multiple radio channels can be provided on the same cable. Certain radio channels could also be used with data channels for control or supervision of remote equipment or environmental conditions. In addition, the same cable can be used to distribute or monitor signals from remote TV cameras in selected or dangerous areas. The system can be interfaced to a telephone system, if required, to provide extended communications to above-ground workshops, offices, medical stations or even hospitals and other emergency services.IntroductionReliable communications among personnel throughout an underground mine area have long been the dream and goal of various mine operations personnel. The system to be described was designed to meet this objective."

Jan 1, 1983

By N. Fukatsu

The recent development of galvanic cell-type hydrogen sensor for molten copper was outlined. The principle of the sensing mechanism, the fundamental structure of the sensor, and its performance as a process control device are discussed based on experimental work undertaken by the authors. Besides sensors based on usual perovskite-type proton conducting oxide, those using magnesium-doped alpha alumina, which was recently known as a proton conductor, were investigated and the results at the laboratory scale are reported. Considering the excellent sensitivity at high temperature and the stability to the disturbance from the attendant oxygen activity, magnesium-doped alpha alumina was regarded to be a superior material for the sensors used for such purposes.

Jan 1, 2007

By M. Matsuda

The Hitachi refinery of Nikko Smelting & Refining Co. Ltd. began its electrolytic copper refining operations in 1911. In December 2002, the refinery changed its operation scheme by introducing the ISA permanent cathode technology for the first time in Japan. The change resulted in higher productivity, better cathode quality, and lower operational costs. The operation has been continuously improved to reach a 20% higher production capacity than the original one. For the electrolyte purification process, the Hitachi refinery has developed a new process for removing impurities. The process involves As, Sb and Bi adsorption from the electrolyte by means of chelating and ion exchange resin. The new resin process will achieve higher efficiency in removing impurity.

Jan 1, 2007

By Edward R. T. Tiekink

Metal complexes continue to find therapeutic applications for the treatment of a wide variety of human ailments. Amongst these, gold(I) thiolates are used to treat rheutmatoid arthritis but, usually in combination with other treatment or as a last resort. New therapeutic uses of gold, both as gold(I) and gold(III), are being sought, including against cancer, the focus of the present contribution. It will be demonstrated that certain gold(I) complexes show exciting cytotoxicity profiles, rivalling those of cisplatin and standard chemotherapeutic agents. More importantly, anti-tumour activity is demonstrated in vivo, albeit in a mouse model. The presentation will give a brief overview of ?metals in medicine? with a focus on gold and will summarise some recent advances in the development of goldbased anti-tumour agents.

Oct 1, 2003

By V. Vekris

A diverse patent portfolio and an effective intellectual property strategy are vital in today’s small business world. Not only does a diverse patent portfolio enable a company to secure a monopoly within the market, it greatly increases the value of a company’s intangible assets and keeps competitors at bay. An overview of the patenting process as it pertains specifically to the materials science-related start-ups will be given, together with a summary of some general patenting strategies and a review of some patenting errors to be avoided, such as premature disclosure of the invention to the public. Additionally, a review of new “green technology” initiatives recently adopted by Patent Offices around the world is also provided. These initiatives are expected to greatly benefit patent applicants in the fields of metallurgy and mining, where research efforts are often directed to environmentally-friendly products and processes. INTRODUCTION Patents are playing an increasingly significant role in the business world. A diverse patent portfolio can enable a company to secure a monopoly within the market, which can provide a competitive advantage over competitors. At the same time, patent portfolio of any size can greatly contribute to the total value of a company’s intangible assets. As an example, Nortel entertained bids in 2011 for its portfolio of about 4000 patents, a large portion of which were directed to 3G- and 4G-mobile communication technologies. The portfolio was eventually sold for $4.5 billion to a consortium including Apple, EMC, Ericsson, Microsoft, Research in Motion, and Sony. Copper mining, and indeed the global mining industry as a whole, is facing challenges. Ore deposits are increasingly low grade, complex, and deeper in the ground, rendering copper mining operations more difficult and costly. Production costs are increasing. According to one study, the cost of producing copper has increased by an average of 10% per year since 2005 (Cantallopts, 2017). To illustrate, the cost of producing a pound of copper in 2005 was 90 cents, but had increased to 217 cents by 2014.

Jan 1, 2019

By Jeremy Breker

Cameco aligns its social and environmental responsibilities with its vision, mission and values. Environmental Leadership is established as a corporate objective that emphasizes the triple-bottom-line and a systematic approach to understanding environmental, social and economic issues, risks and opportunities. These are ingrained in the project culture, systems and processes and used to influence solutions derived by the project teams to achieve Cameco's objectives. This paper traces the organizational objectives from the early stages of a project through to implementation and turn over to Operations. A case study is used to demonstrate how an asset is influenced by Cameco?s strategy.

Aug 1, 2010

By M. D. Gerst

The degree to which copper will continue to be in an integral part of the world economy in the future will depend largely on the dynamics of global economic development, the primary and secondary copper resource stock, technological change, and potential environmental constraints. We have characterized the copper cycle of 1994 for all of Earth's regions and for the planet itself (T. Graedel et al., Environmental Science & Technology, 38, 1242-1252, 2004) and recently updated that cycle to year 2000. In this paper, we compare various features of the 1994 and 2000 cycles. The three largest-using regions, Asia, Europe, and North America, all increased their absolute rate of copper use between 1994 and 2000, and all increased the per-capita rate of copper use as well. Globally, the use of copper increased by about 32%, from 11.7 to 15.3 million metric tons, while population increased by only 8%. Various changes are seen in scrap trade, finished products trade, and other parameters of the cycle. We conclude by considering how the rates of technological change and growth in demand, especially in Asia, may influence the copper cycle in the years ahead.

Jan 1, 2007

By Joseph J. Poveromo

The blast furnace today continues as the primary production method of hot metal in large-scale steel production. The blast furnace process has been the target of repeated attempts to replace it with various process options, including direct reduction and coke-free smelting reduction. While these new technologies are being adopted in appropriate niches, the blast furnace has responded to the challenge by being amenable to continuous improvement. I will review the role of the blast furnace, major developmental and improvement trends, and then list the current important issues in ironmaking. I will outline the challenges to be faced by the blast furnace to maintain its position as the primary hot metal production process. The material presented here is an update of earlier presentations made in Stockholm, Sweden, 1996, Duluth, 1998 and Chicago, 2000.

May 1, 2003