Search Documents

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet 'below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By H. A. Kramer

The Flin Flon mine is at present hoisting 5,000 tons of ore daily. In 1943, a peak production of 6,188 tons daily was maintained. Before discussing secondary blasting, it is felt that a short review of stoping procedure will be of value. A list of papers dealing with various phases of the mining operation is appended. Stoping Practice Stopes vary in width from 30 to 150 feet, in length from 200 to 450 feet, and in height from 200 to 500 feet. A typical stope would be 300 feet long, 300 feet high, and 90 feet wide. The dip of the orebodies varies from 60° to vertical, with an average of 82°. The ore is heavy, having a specific gravity of 4. Both sub-level benching and radial drilling are practised. Blast-hole diamond drills are responsible for 85 per cent of the total production. Two sizes of hole are drilled at present, 11 7 6 -inch and 1%-inch. For bench drilling, the burden on the 1 7/16-inch hole is six feet, with holes on 8-foot staggered centres; in radial drilling, the burden is six feet, with nine feet between the toes. The burden on the l 5/8-inch hole is eight feet with holes on 11-foot centres, or 13 feet on the toe of fanned holes. Holes are blasted with two No. 8 instantaneous electric caps per hole, using 403 Polar Forcite. A powder charge of 0.15 pounds per ton is used, with a tonnage factor of 5 and 6.4 per foot drilled for the two sizes. Two rows of holes are blasted together. Fragmentation is satisfactory with the above drilling pattern and powder charge. However, some overbreak and fall-off locally results in oversize material. It is estimated that, after primary breaking, 75 per cent of the ore will pass through the grizzly openings and 15 per cent will pass the draw points, leaving 10 per cent that must be broken further to pass the draw points.

Jan 1, 1946

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By E. H. Mulligan

THE ERRINGTON B-I mine is located on the Errington orebody of Steep Rock Iron Mines, Limited, at Steep Rock Lake, Ontario. In 1946, this orebody entered the shipping lists of the Lake Superior iron ranges as an open-pit operation. During the period 1946 through 1953, the mine produced a total of 9,000,000 tons of iron ?ore. In 1950, as the mine approached the economic limits for open-pit operations, ground was broken for an underground development to exploit the deposit at depth. The mine is designed for an ultimate production of 1,500,000 tons per year by the block-caving system of mining. The initial shaft is 1,200 feet deep and will produce or-e from the 700 and the 900 levels. The 1,100 level will be used as a drainage level and as a haulageway for waste rock, which is hoisted to surface by skip. Ore from the two production levels moves by a system of ?ore passes to a crushing plant located below the 900 horizon and is hoisted from this point to surface by conveyor belt. At the present time, all material handling on the levels is by tramming, but as tram distances increase conveyor haulage will probably be installed. The initial stage of the Errington B-1 development is expected to produce 6,000,000 tons of ore over a period of four years. The second stage will require deepening of the shaft and development of lowe1? production levels. The conveyor hoisting plant will be extended to serve these new levels. We visualize the mining of this orebcdy down to 2,500 feet by these methods.

Jan 1, 1956

By T. Loos

The Norddeutsche Affinerie operates an Outokumpu-Flash-Furnace as a smelting unit. The pyrometallurgical slag cleaning process is based on the slag reduction and settling in the electric furnace. Since 1972 when the slag cleaning furnace was built the throughput could be increased fourfold. However, an extensive optimisation effort is required in order to keep the copper loss low. A parameter study with a neuronal network model based on real process data was conducted to identify parameters impacting on the copper loss in the slag. It could be demonstrated that the main parameters responsible for copper loss in the final slag are fixed parameters of the flash furnace. For a better understanding of the copper loss in the electric furnace microscopic analyses of the slag structure and viscosity measurements were performed. Based on these results the reduction and settling of the copper containing droplets could be increased in both pilot plant studies and industrial scale. 4

Jan 1, 2007

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d'Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016

By R. A. L. Drew, G. Mendoza-Suarez, J. Filipi, R. Vintila, J. A. Kozinski

Economics and environmental considerations along with the increasing demand of hydrogen encourage development of novel technologies such as plasma processing of hydrocarbons and thermal cracking of natural gas. Plasma discharges, either in thermal or non-thermal regimes are expected to allow low temperature and fuel flexible on-site hydrogen generation. The main drawback of thermal plasma reformers is the high-energy consumption resulting from high-temperature operation. On the other hand, non-thermal plasma, generated by dielectric barrier discharge (DBD), is able to simulate the chemical reactions employing much lower energies than those required by thermal treatment processes. The non-thermal plasma process allows for instance, a direct conversion of methane into hydrogen and carbon black with no CO2 release. The focus of this research was on the GHG-free method of H2 generation in compact non-thermal plasma reactors using low, medium and high permittivity dielectric ceramics. A stable, non-thermal plasma was generated by placing a dielectric ceramic between two electrodes with a 25 thou gap and applying an alternating current of 1-5kHz and voltages of 4-8kV. In order to ensure energetic efficient plasmas, experiments were conducted to analyze the behaviour of different permittivity ceramics. It was found that the dielectric properties of a ceramic, when used in a DBD reactor, have a strong influence on the discharge characteristics, which in turn influence the power consumption. Higher dielectric constant resulted in higher conversion rates of methane (higher yield of hydrogen and carbon). At the same time, the mechanical properties of the dielectric material, which are closely associated with its processability, influenced its resistance to electron bombardment, as well as thermal and mechanical damage. Therefore a reliable ceramic should have good dielectric properties, in addition to good thermo-mechanical stability.

Jan 1, 2004

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By Engineering Staff

In 1958, the Iron Ore Company of Canada decided to proceed with the Carol Project. The ore deposits in the area are part of the highly metamorphosed southern zone of the Labrador Trough. They lie along the shore of W a bush lake, in the western part of Newfoundland-Labrador, 190 miles north of Sept-Iles. The project is designed to mine, by open-pit methods, 17,200,000 long tons of crude ore, grading 37 per cent iron, per year. This ore will be beneficiated to produce 7,000,000 long tons of concentrate, grading 66 per cent iron, of which 5,500,000 long tons will be pelletized. Production is scheduled to commence this summer. Initially, ore will be taken from 45-foot benches in the Smallwood mine, using jet-piercing production drills and large-scale blasting with "slurry" explosives. Four 13-yard electric shovels will muck the broken ore into 100-ton trailer trucks. The trailers will be hauled to two 2,000-ton loading pockets, which feed the ore into 100-ton railcars. Four ore trains, each comprised

Jan 1, 1962

By Roméo Roussin

"The yearly production from the Asbestos Hill pit is 1,550,000 tons of asbestos ore, with a yield varying between 18 and 20 % . The orebody was exposed at the top of a hill, and initial production started without having to remove any overburden. The projected ratio of barren rock to ore, based on the present orebody, was 2 to 1. However, as it was necessary to push back the upper benches, this ratio has changed to 3 to 1. The final pit will be 2,300 feet long by 1,000 feet at the longest and widest points. The final depth will be 680 ft. A pit slope stability study was carried out and an average wall angle of 60-70 degrees must be maintained. Preshearing of final pit limits will produce good wall stability. Permanent access ramps will be 60 ft wide, with an 8 % maximum grade. Geological conditions and the low rock temperature are the major causes of the operation's drilling and blasting problems."

Jan 1, 1976

By D. Newman

"This paper discusses the author’s work on international law norms of consultation with Indigenous communities and examines unexpected corporate stakeholder impacts on these norms. Customary international law, which governs the area, does not traditionally refer to corporate conduct. This paper surveys several sources on developing international law on consultation obligations; it also discusses the impacts these norms can have on corporate stakeholders in the mining industry. Finally, it asks how interactions of corporate stakeholders in this area can indirectly impact future law and suggests implications for different business models in the mining sector.RÉSUMÉ Le présent article traite du travail de l’auteur sur les normes de consultation avec les communautés autochtones contenues dans le droit international et examine les impacts inattendus des parties prenantes sur ces normes. Le droit coutumier international, qui gouverne ce domaine, ne réfère traditionnellement pas à la conduite des sociétés. L’article analyse plusieurs sources traitant du développement de nouvelles lois internationales sur l’obligation de consulter; il traite aussi des impacts que ces normes peuvent avoir sur les parties prenantes dans l’industrie minière. Finalement, il pose la question à savoir comment les interactions des parties prenantes dans ce domaine peuvent avoir un impact indirect sur les lois futures et il suggère des implications pour divers modèles d’affaires dans le secteur minier."

Jan 1, 2015

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967

"The asbestos mining industry in the Eastern Townships of Quebec has early recognized the undesirable side-effects associated with mineral production, such as air pollution, noise and unsightly waste dumps. In order to efficiently achieve the industry's aim of eliminating or minimizing these objectionable features of mining, all of the asbestos producers in Quebec interchange information, knowledge and design dealing with the environmental control measures through the Environmental Committee of the Quebec Asbestos Mining Association.The paper describes what has been done and what is planned for the future in the various problem areas, such as control of dust emitted during the open-pit drilling operation, control of dryer stack emissions, control of the environment in ore, fibre and tailings handling operations, rehabilitation of the countryside covered by waste dumps, and many others."

Jan 1, 1971

By P. E. Cavanagh

"The Davis tube test has been used for many years as a laboratory method for determining the magnetic iron re-coverable from a magnetite iron orebody. This paper de-scribes a method for determining the recoverable iron from ores of the Labrador Trough type, with the usua1 flow sheet utilizing spirals followed by magnetic separation.The mechanical structure of a metamorphosed iron ore, resulting from recrystallization over long periods of time, is the basis for the laboratory method developed. Similarities between the structures of such recrystallized ores and the structure of annealed and recrystallized steel are noted.A laboratory technique to determine the size of the different grains of gangue and iron ore minerals is de-scribed and the application of this information to arrive at recommended grinding techniques and flow sheets is demonstrated. The use of the method to determine recoverable iron in such ores is compared to actual iron recovery in the pilot-plant and commercial concentrations of the same ore.The use of a specified lower limit of recoverable iron as determined by this method, in order to design open-pit limits, achieves practical results when compared to designing a pit based on an arbitrary lower limit of total soluble iron. The Ungava Iron Ore deposits are used in giving an example of the resulting pit design changes."

Jan 1, 1968