Search Documents

By Shuai-Jun Li, Xia-Ting Feng, Xian-Jie Hao

"The anisotropy of rock is of great importance to the rock engineering. To investigate the anisotropic character of slate, the rock samples of slate under different confining pressures and bedding plane angles was conducted on the MTS. The results indicated that the relationship between bedding plane angle and elasticity modulus, friction angle, cohesion and strength was shown as U pattern. The minimum value of them is located from 30°to 45°.In addition, the elasticity modulus and Poisson's ratio increase with the increasing confining pressure. The slate behaves brittle failure both in the uniaxial and triaxial compression. The failure pattern of uniaxial compression is generally tension failure, and triaxial test usually shows shear failure. The failure angle decrease with the increasing of confining pressure.INTRODUCTIONThe anisotropy of rock is that loading in different orientations the rock has different mechanical properties. The anisotropic property of rock is always an important problem in rock engineering (Hoek E. & Brown E. T., 1980). J. C. Jaeger (1960) first presented that transverse strength criterion for sliding fracture on joint surface. Later he revised rock parameters to anisotropy empirically for isotropic Mohr- Coulomb criterion. His main idea is revising cohesion according to loading direction (J. C. Jaeger, 1971). Then, many scholars study a lot on transverse strength criterion. E. Z. Lajtai (1969) considered the influence of connecting rate in all directions in joint groups for shear strength in intact rock; R. Mclamore and K. E. Gray (1967) referenced the theory of J. C. Jaeger. They not only revised cohesion also revised friction coefficient. Y. M. Tien (2000, 2001) made further study on the influence of connecting rate in joint group to transverse strength. R. Nova (1980) studied on the variation of strength when rock specimens in triaxial pressure and complex stress paths. O. Cazacu(1998) put forwards a new anisotropic strength criterion for analyzing rock strength. S. Pietruszczak(2000) introduced fabric tensor for characterizing inner seismic structure and he built an anisotropic strength criterion containing the invariants of stress tensor and seismic fabric tensor."

Jan 1, 2015

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By Roy O. Ifill, W. Charle Cooper, Alan H. Clark

"Queen’s UniversityIn representative, run-of-mine samples from the Panel and New Quirke mines of the Elliot Lake uranium district, Ontario, brannerite, ametamict uranous titanate, occurs in microscopic grain-aggregates which display wide variations, both in textural habit and in the relative proportions of brannerite, titania polymorphs and/or “uraniferous titania”. As is widely documented, much of the brannerite occurs as trellis-like arrays of laths and needles pseudomorphing rutile oranatase. In some cases, the laths and needles are cemented by coffinite. Brannerite, with an average composition of (U0.629Th0.039Ca0.20)(Ti2.199Fe0.13)O69contains =3 wt% Th and is distinctly Ti-rich relative to the ideal composition, UTi2O6. Much of the Si reporting consistently in electron microprobe analyses (between 1 wt%and 5 wt%) is tentatively attributed to contamination by the quartz-sericite matrix, and a minor proportion is attributed to the presence of coffinite intergrowths. “Uraniferous titania” (average par-tial composition by weight: 10.8% U, 0.3% Th,32.9% Ti) is considered to represent an intermediate stage in the conversion of titania to brannerite.The leaching behaviour of brannerite in its different modes of occurrence was studied qualitatively by the rotating-disc (polished section) method in H2SO4and HCl solutions at 25° to70°C. Redox potential was not measured. The progress of the dissolution of the individual brannerite crystallites and grain-aggregates was monitored by optical and scanning electron microscopes. Regardless of its morphology and texture (laths or needles, reticulate or blocky),brannerite is not readily leachable. Regardless of the process conditions, the rate-controlling step appears to be the initial leach-pit formation. These pits expand radially through the aggregate as leaching proceeds. This dissolution mode is independent of the relative amounts of brannerite and titania, i.e. the type of grain-aggregate. Secondary coffinite intergrowths are readily leachable and enhance the overall leaching kinetics of brannerite by accelerating leach-pit formation. These data provide, for the first time, information on the controls on the leaching of the uraniferous phases which dominate the lower-grade ores in the Elliot Lake district."

Jan 1, 1996

By Gwenaële Petit, Ulan Massimkhanov, Gilles Joubert

For its Zuuvch Ovoo uranium deposit in Mongolia, Badrakh Energy (partly owned by Orano Mining) is working on the prefeasibility study for exploitation by ISR (in situ recovery). As part of this project, Orano built a 2-cell (each cell is constituted of one producer well located in the center and surrounded by six injection wells in an hexagonal pattern) and a processing pilot plant that will be used to demonstrate the operability and economic viability of an ISR process. Another main objective of this pilot trial is to demonstrate the ability of Orano’s modeling tools to predict the ore behavior under given leaching conditions. To model uranium production by ISR, Orano uses HYTEC, a reactive transport computational software, which was adapted for its existing operation in Kazakhstan (Katco) to predict uranium recovery and reagent usage based on operating conditions. In order to perform similar simulations for this new deposit, Orano engaged in a comprehensive program including ore sampling, detailed characterization, and metallurgical testwork. The mineralogical conclusions were used to prepare a simplified geochemistry for the ore, in particular carbonate and reactive clay grades, uranium mineralization and penalizing elements such as pyrite. Then, bottle roll leach tests were used to characterize dissolution kinetics for smectite clays. Eventually, column leach test results such as pH, free acid, and uranium recovery were modeled on HYTEC to improve the fit of some of the dissolution kinetic parameters. Parameters fitted using metallurgical test work results will now be used as inputs for predictive model at the pilot scale, in order to anticipate operational results and help with operating decisions for production ramp up.

Jan 1, 2020

By A. B. Walker

The effects of the injection of dry limestone additives into boilers for the sorption of sulphur dioxide have been studied in pilot and full-scale systems. The effects of such injections on boiler mass particulate emissions as well as collectability characteristics of the fly ash and reaction products are presented. Implications of the effects on the design and economics of particulate collectors, in particular electrostatic precipitators, are discussed.

Jan 1, 1971

By C. Yanqui

"Discontinuum Mechanics is based on two foundations: the idealization of the internal structure of substances, and the principle of the arithmetic mean value. For a linear discontinuum, the methods of Crystallography are used to describe their structure, in which nodes stands for the position of the homologous points such as molecules, grains, or any other motif. The principle of the mean value states that the value of any discrete function at a node is equal to the arithmetic average of the values of this function at the neighboring nodes. This principle leads to an elliptical linear differential equation of the second order, with coefficients given by the statistical second moments of the Cartesian components of the metric vector. As long as those coefficients are components of a symmetric second-order tensor, there are three mutually perpendicular directions, in which the variances reach their extreme values and the covariances are zero, showing that the mean value principle transforms the discontinuum into a statistically equivalent orthotropic continuum.The application of Discontinuum Mechanics to linear rock masses is simple and direct. It is sufficient to define the motif as the plane of geological discontinuity, and the metric vector as the normal vector to this plane, whose magnitude is the spacing between two consecutive planes belonging to the same set of discontinuities. Furthermore, heterogeneities of rock masses can be also included in this description by substituting the plane of discontinuity by a zone of weakness. In this way, the magnitude of the normal vector results from the product of the spacing and the RQD or the RMR. In going further in this theory, at least three conclusions show up. First, in the evaluation of rock masses, it is necessary to determine the orientation, spacing, and RMR for each set of discontinuities. Second, the conventional method of finding the principal families from the contours of equal concentration of poles on the stereographic projection excluding the spacing does not have any physical meaning. Third, any problem of rock mechanics can be solved in a rigorous and reliable way by integrating the differential equation of the mean value."

Jan 1, 2015

By J. Fournier, D. Fortin, F. Robichaud

Since milling began in 1988, the Laronde mill has been expanded several times, the most recent, increasing the milling rate from 5 000 to 7 000 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails in order to cope with high silver/gold ratio associated with the discovery of the Penna shaft. Since the commissioning of the Merrill-Crowe refinery in 2000, several modification and expansion projects were performed to reduce health and safety hazards. Remarkably, several of these improvements have contributed at increasing productivity and Net Smelter Return of the refinery while reducing worker's injuries. In 2004, the refinery was audited to evaluate and quantify the circuit performance. Metallurgical and mechanical operating conditions of the refinery are now understood and areas for further improvements are well defined. This paper describes some of the factors that have contributed to this improvement and describes how ergonomics and recovery can further be improved.

Jan 1, 2005

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By R. W. Diamond

PUBLIC debts, and the policies guiding public finance in Canada today, are in such a state that every intelligent citizen should be familiar with them, and should be concerned about them. None of you have robe reminded that taxes have already risen to a point where they both annoy and hurt you, but they should also alarm you; alarm you, not so much because of the taxation, but because of the mounting expenditures represented by that taxation. I have no hesitation, therefore, in presenting a paper dealing with public finance at a meeting of the Mining Institute, since all present are concerned,. both as individuals and as representatives of the industry. Moreover, it is important that engineers, particularly, should become better acquainted with the interlocking relationships of economics, public finance, government, and technology. While I am neither an economist, a tax expert, nor a chartered accountant, I shall try to tell you, from my viewpoint as an engineer and an interested voter, the story of public finance in Canada today and of certain causes and effects, and I shall venture certain conclusions. In doing so I may merit criticism by experts, but I will risk this in the hope that sufficient interest will be stimulated in the subject to persuade you, as individuals and as groups, to advance, or to institute, your own studies in public finance, and in turn to interest others. I hope that some of the ideas which will be expressed, or which may develop, will bear fruit. I fully realize that several eminently qualified men have spoken on this subject during recent months, and that many authoritative articles have been written. However, I approach it with confidence, because I propose speaking to you not as an authority, bur as one of you, having similar interests and similar engineering knowledge, who only a few months ago became particularly interested in the subject, studied it, and who now sets before you a summary of his findings, with the conviction that the situation is so serious that constructive planning and constructive action by all thinking citizens are imperative.

Jan 1, 1939

By P. A. Tichauer

Arbitration is a flexible method for dispute resolution that gives control to the disputing parties while still maintaining a clear and well-structured decision making process. It responds to the desires of the parties for a resolution that is fair, binding and enforceable and is guided more by pragmatism, efficiency, effectiveness and equality than by a need to comply with the legal procedures and practices of any single country or jurisdiction. Arbitration is particularly well suited for the resolution of disputes pertaining to international commercial agreements which are often present in the metallurgical sector. This paper provides a simplified outline of the features and advantages of arbitration as well as commentary regarding certain prerequisites in order for arbitration to be binding and enforceable.

Jan 1, 2015

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By W. A. Green

To those who may not be familiar with the history and organization of the Flin Flon mining property from the rime of its examination and option by the Harry Payne Whitney interests until the present start of operations by the Hudson Bay Mining and Smelting Company, Limited, this paper may give a better understanding of the property. More technical discussions are being presented to you by the men most closely connected with the various operations of the property. Location The Flin Flon mine is situated along the boundary line between the Provinces of Manitoba and Saskatchewan at approximately. 54° 45? north latitude, but largely in Manitoba. Prior to the advent of the railway, the property was quite isolated. The summer route was over a course of some 175 miles, consisting of a 125-mile boat trip from The Pas, first up the Saskatchewan river, then across Cumberland and Sturgeon lakes to Sturgeon? Landing. From Sturgeon Landing, a .16-mile portage was necessary to Camp 2 on lake Athapapaskow. From Camp 2 the route consisted of a canoe trip of 32 miles across lake Athapapaskow, up the northwest arm of Schist lake, then up Ross creek to the Company's docks, and finally a 2-mile walk to the property. The winter route was just under 100 miles in length, the difference being due to the fact that a more direct route could be followed over the frozen lakes. It went up the Saskatchewan river for a short distance above The Pas and then, leaving the river, the road followed Reeder, Rocky, and Sturgeon lakes to Sturgeon Landing, and from there over the same route as the summer one, only across the frozen lakes.

Jan 1, 1930

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

Numerous data in the literature confirm that the chemical composition and consumption of grinding media influence electrochemical properties of flotation suspension as well as effectiveness and selectivity of upgrading processes. During a milling process, attrition of grinding media is observed. Depending on the susceptibility to abrasion, the grinding media influence, to a different extent, the redox potential, pH as well as flotation efficiency. As a result, different upgradeability of sulfide minerals is observed. The paper presents laboratory scale flotation results, obtained for the copper sulfide ore from Polkowice Region of KGHM Polska Miedz S.A. in Poland ground in the presence of forged steel, highchrome iron and stainless steel as the grinding media. The investigated flotation feed contained 36 g/t (ppm) of silver and 1.86 % of copper. Several flotation tests were conducted using fixed amount of frother and a mixture of sodium ethyl and isobutyl xanthates as the collector at three different doses of 75, 100 and 125 g/t. A comparison of the obtained results confirmed that the application of grinding media with different chemical compositions influenced the electrochemical properties of the suspension and recovery of silver and copper in the final concentrate. The highest values of redox potential were observed for the stainless steel as the grinding medium. Moreover, in the presence of this type of grinding media, regardless of the collector dosage, the best silver upgrading was observed. For the forged and high-chrome iron media, the recovery of silver depended on the collector dosage. It is indicated that higher levels of the redox potential, together with smaller amount of iron released from the grinding medium, improve the flotation of the silver-bearing mineral compounds from the copper sulfide ore.

Jan 1, 2016

By Y. Jiang, B. Li, R. Liu

"In this study, laboratory flow tests were conducted on 2-D artificial rock fracture network models containing a single intersection constituted by two inlet and two outlet branches. Three models with different intersecting angles of 60°, 90° and 120° were tested using both dye solution and distilled water. Constant flow rates were imposed on one inlet, and the flow patterns in the fracture intersections were captured by using a CCD camera. The test results were compared with the predictions made by numerical simulations that solved the Navier-Stokes equations. The results revealed that when Reynolds number (Re) is as low as less than 1, the intersecting angle has negligible influence on the flow rate of each branch and the flow patterns within a fracture intersection. As the interesting angle ? and Re (e.g., from 10 to 200) change, the normalized flow rates of different outlet branches change significantly, due to the inertial effect of fluid flow. These changes could be represented by a series of mathematical expressions involving Re and ?, which could be applied to fracture network models to improve their prediction accuracy on hydraulic properties (e.g., permeability and breakthrough curves of particles) of rock masses. INTRODUCTIONCoupled stress, flow, heat and mass transport are the corner stone subjects for many geoscience and geo-engineering disciplines, such as geological disposal of radioactive waste and geothermal energy exploitation. Many outstanding issues need to be investigated to enhance the knowledge on these subjects, and specifically more in-depth research in testing and modeling of the fluid flow in fractured rock masses is needed. In recent years, discrete fracture network (DFN) models have been extensively used to study the fluid flow and mass transport behaviors of fractured rock masses (e.g., Min et al., 2004; Zhao et al., 2011). In these models, each fracture is usually represented by a parallel-plate model, in which fluid flow exactly follows the cubic law. Therefore, comparative flow rate in each outlet branch of an intersection in these models only depends on its aperture. In reality, due to the surface roughness of fractures, the magnitude of mechanical aperture is usually larger than that of the hydraulic aperture of each fracture (Li et al., 2008; Xiong et al., 2011), and abundant flow patterns could exist in an intersection, influenced by its geometry, varying with changing Reynolds number (Re) (Kosakoswski & Berkowitz, 1999). Recent studies have also revealed that different mixing patterns might exist at a fracture intersection, bounded between streamline routing model and complete mixing model, that determine the final distribution of solutes in fractured rock masses (Johnson and Brown, 2001; Park et al., 2001). Numerical simulation has been the principal method adopted in previous studies, and the studies conducting flow tests on intersected fractures are less reported (Wilson & Witherspoon, 1976; Johnson and Brown, 2001). In this study, laboratory flow tests and numerical simulations by solving the Navier-Stokes equations were conducted on 2-D models containing a single intersection constituted by two inlet and two outlet branches, intersected at different angles. The main objective is to study the influence of intersecting angle on the flow behavior of the intersected fractures and the variations of flow patterns and fluid redistribution in each model along with the changes of the Re and the intersecting angle ?. The influence of surface roughness was not considered."

Jan 1, 2015

By J. R. Kish, J. Dabrowski

"The susceptibility to intergranular corrosion modes is a major technical issue preventing widespread utilization of higher strength welded AA7xxx extruded beam profiles, in the peak-aged T6 condition, in automotive bumper assemblies. A study was undertaken to evaluate the relative exfoliation corrosion resistance (ASTM G85-A2) as a function of joint design parameters, namely the base alloy composition, heat-treated condition and beam orientation after exposure to a cyclic acidified salt spray test. This paper documents the major findings extracted from this study.INTRODUCTIONBumper systems play a predominant role in the passive safety of an automobile, since they are one of the main structures for absorbing the collision energy in the event of an automobile crash. Heattreatable AA6xxx-series (Al-Mg-Si) and AA7xxx-series (Al-Zn-Mg) Al alloys, with relatively high strength, toughness, energy absorption, weldability and formability, make it possible to design costcompetitive bumper systems to crush in a controlled fashion. In this context, Cu-lean AA7xxx extrusions, such as AA7003 and AA7108, which exhibit higher strength than AA6xxx extrusion, such as AA6082, represent an attractive light weight material from which to fabricate bumper assemblies (Clausen et al., 2000; Pedersen et al., 2008; Chen et al., 2009).Arc welding is a key joining process for AA7xxx alloys within the transportation industry. A major technological issue preventing widespread utilization of arc-welded AA7xxx joints is the susceptibility to severe localized corrosion (Kent, 1970, Reboul et al., 1985; Holroyd et al., 1987). It generally occurs as exfoliation corrosion within a heat affected zone (HAZ) a few millimeters from the weld bead, or a type of stress corrosion cracking (weld-toe cracking), which initiates at the weld toe and propagates into the interfacial region between the weld bead and the HAZ (so called “white zone”). In addition to the micro-galvanic cell activity induced by the intermetallic compound constituent and strengthening particles present, there is strong evidence that macro-galvanic cell activity between the weld bead and base AA7xxx alloy may be playing a controlling role. Electrochemical profiles taken across fusion welded joints, in cross-section, during exposure to saline solutions suggest that a significant potential difference exists across the AA7xxx arc-welded joint (Shumaker et al., 1967; Grauer and Wiedmer, 1980; Tuck, 1985, Onoro and Ranninger, 1993). These studies consistently show that the HAZ and base alloy are more electronegative with respect to the weld bead (arc-welded with AA5xxx filler wire). Despite this initial important work, the majority of the recent corrosion research effort on welded AA7xxx alloys has focused on the performance of friction stir welds (Lumsden et al., 1999; Wadeson et al., 2006; Hatamleh et al., 2009)."

Jan 1, 2012

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011