Search Documents

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By Steven D. Botts

The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd. , is a $2.3 billion copper/zinc project, located in the Ancash Department in Perú. The project consists of an open pit mine, a 70,000 ton per day concentrator, a 302 Km. long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 million tonnes per year of copper and zinc concentrates over a 23-year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world. This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28th, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14th, 2001 by Peruvian president Alejandro Toledo. The construction stage of the project generated 8,000 direct jobs, with a peak of 10,000 employees, and 30,000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals; around 30% of whom came from the department of Ancash where the deposit is located. Approximately 5,800 indirect jobs will be generated from the project. Independent sources state that Antamina will increase the Peruvian mining exports by 30% and Peruvian GDP by 1.4% within its first year of full operation in 2002. Since winning the privatization bid for the project in 1996, the company has implemented a successful approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company?s environmental program. Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues, and as a result, has set new standards in Perú for environmental and community management, and sustainable development.

May 1, 2002

By M. Mbonimpa

Field experimental cells were constructed in 2007 to assess the performance of different cover scenarios for the reclamation of the Parc 1 tailings disposal facility at the Westwood-Doyon Mine site (Abitibi, Quebec). Three configurations of cover with capillary barrier effects (CCBEs) with different thicknesses and material types for the moisture retention layer (MRL) were studied. MRL with 80 cm till, 40 cm till, and 40 cm clayey silt were used for cell nos. 2, 3, and 5, respectively. The capillary barrier layer (CBL) and drainage and protection layer (DPL) of the CCBE consisted of 30 cm gravel. A reference cell without cover was also constructed to compare the geochemical performance of the CCBEs. Due to an unexpected flooding in the leachate exit area of the cells in spring 2008, the cell instrumentation for hydrogeotechnical monitoring was postponed to spring 2009. Changes with time in volumetric water content, suction, soil oxygen concentration, and temperature were measured at different depths. This paper presents and discusses preliminary results obtained from spring 2009 to autumn 2010. In all cases, the degree of saturation Sr is lower in the CBL than in the MRL, indicating the presence of capillary barrier effects at the interface of these layers. Cell nos. 2 and 5 showed hydrogeotechnical behavior typical of an effective CCBE, with Sr maintained above 85% in the MRL and lower than 30?50% in the DPL and CBL. Based on the obtained results, and as expected, MRL thickness and the type of construction material used appear to affect the hydrogeotechnical behavior of the CCBE. Oxygen concentration profiles through the CCBEs were used to estimate the oxygen flux, and results indicate that cell nos. 2 and 3 performed better than cell no. 3. CCBE performance is currently being investigated using the geochemical monitoring data.

Aug 1, 2013

By Karen Munro

Importance of Aquatic Studies for Mining ?Aquatic habitat is usually the first area where a mine interacts with the ?real world? outside the mine footprint ?Water management is a key consideration for a mine?Effects on the aquatic environment often extend to wildlife and human uses ?There is a lot of regulatory focus on issues of water quality, fish and fish habitat

May 1, 2011

By A. Bowles

The process of accumulative roll bonding (ARB) has been applied to wrought magnesium alloy AZ31. Accumulative roll bonding results in severe plastic deformation of sheet material. In AZ31, this process leads to the refinement of the microstructure by dynamic recrystallization. The refinement of the microstructure results in an improvement in mechanical properties with potential for producing materials for superplastic forming. In this work AZ31 was bonded with up to 64 layers and the potential of roll cladding with aluminium was also investigated. The development of microstructure and the mechanical properties are reported here.

Jan 1, 2006

By Kuwauchi. Y., M. Barati

Recycling of dust using a rotary hearth furnace (RHF) has gained considerable attention in the past two decades for the sustainable production of steel with less environmental impact. In order to further promote the recycling of electric arc furnace dust and carbonaceous wastes using the RHF process, a mathematical model was developed to predict the reaction behaviour of dust-reductant composites. The reduction kinetics of zinc and iron oxides as well as the volatilization behaviour of volatile matter in the reluctant were considered. The modeling approach and some preliminary results are presented in this article.

Jan 1, 2011

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

By M. E. Holter

"Five main lignite seams occur in the Tertiary Ravenscrag Formation in the Eastevan area, at depths of 100 feet or less. They are named, in ascending order: the Boundary, Estevan, Souris, Roche Percee and Short Creek seams. A total sequence of approximately 250 feet is represented by the coal beds and interstratified clays, silts and sands. Strata dip to the southeast at 25 feet per mile or less and trike northeast. Large areas underlain by coal seams at shallow depths are delineated. Reserve calculations are dependent on detailed information on seam thicknesses and feasible stripmining depths. The stratigraphically higher seams are thinner on the average than lower seams and this, together with the increase in elastic size fractions in higher strata, suggests a retreat of a Tertiary marine margin to the south during the closing depositional history of coal seams and associated strata."

Jan 1, 1972

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation's greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d'Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By T. H. Patching, D. F. Coates

The Sub-Committee on Rock Classification, Canadian Advisory Committee on Rock Mechanics, has evolved a classification of rocks which should prove useful in studies of rock mechanics. Considered in two stages -actual rock substance and rock mass -the five-point classification involves the geological name of the rock, the rock strength and rock deformation, and, in the second stage, the gross homogeneity of the rock mass and the formation continuity.

Jan 1, 1968

By T. Grammatikopoulos, K. Gibbs, H. De Souza, C. Gunning

The mineralogy of any ore body is a key factor in defining ore zones and predicting minerals/metals behaviour during processing. The determination of forms of gold, defined as the different chemical states in which gold is encountered in ore deposits, is critical. The most commonly known form is that of gold minerals and alloys, while other forms of gold have been collectively described in the literature as submicroscopic gold (i.e., less than 1 µm in diameter). Gold mining operations generally deal with very low-grade ores, in the order of a few g/t, in which gold displays complex mineralogy. These difficulties complicate the mineralogical studies and pose challenges for processing and recovering the gold. A comprehensive understanding of the chemical forms of gold is necessary to define gold mineralization and optimize gold metallurgy. SGS Canada Inc. has been using QEMSCANTM and a Tescan automated SEM that are automated mineralogical techniques that provide vast amounts of data for microscopic Au. The data in conjunction with other physical and chemical methods provide a comprehensive delineation of the ore composition and behaviour.

Jan 1, 2011

By Grant Small, Jessica Kinal, Christopher J. Greet

"The conversion from an electrochemically reactive grinding media (forged steel) to a more electrochemically inert alloy (high chrome white iron) not only reduces the wear rate of the grinding media, but also has an impact on the grinding chemistry. Typically the grinding chemistry becomes more oxidising, with less reducing Eh values and more dissolved oxygen in the pulp. There is also a decrease in the EDTA extractable iron, which is an indication of the change in the media corrosion. These changes are indicative of alterations in the surface chemistry of the minerals that the operator is trying to separate. For porphyry copper ores the changes in the pulp and surface chemistry not only affect the copper sulphide minerals, but also impact the iron sulphides (i.e. pyrite and pyrrhotite). Generally, with more oxidising pulp chemical conditions during grinding there is an increase in the oxidation of the iron sulphides which renders their surfaces hydrophilic, thereby depressing flotation. This leads to improved selectivity for copper sulphides against iron sulphides.INTRODUCTIONPorphyry copper deposits are the dominant source of copper that is mined today to satisfy global demand. These style of deposits typically contain one percent copper mostly as chalcopyrite, but may contain other copper bearing minerals (for example, bornite, chalcocite, azurite, malachite), small quantities of pyrite and quartz. Porphyry copper deposits also contain economically significant quantities of gold, silver and molybdenum. Interestingly, the majority of the world’s porphyry copper deposits are concentrated along tectonic plate boundaries (Figure 1)."

Jan 1, 2016

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By A. Mitura

The paper presents the initial investigation of possible energetic applications of chosen wastes from groups: 06, 03, 05 and 01, including coal slimes being secondary product of hard coal processing. These categories of wastes are catalogued according to the polish law, where 06 ? wastes from production, preparation, purchasing and application of products of non-organic chemistry; 03 ? wastes from wood processing and from plates and furniture, celluloid mass, paper and card board production; 13 ? oil wastes and wastes from liquid fuels; 01 ? wastes produced by searching, extracting, physical and chemical processing of ores and other mineral raw materials. The change of combustion heat value was evaluated in produced energetic mixtures containing these types of wastes together with the change of their individual components. All combinations of ingredients were taken into consideration giving 256 various mixtures, from which 36 were selected to investigation. This allowed the performance of statistical factor analysis. For such prepared materials the application of regressive method was proposed in purpose of calculating combustion heat value and then the comparison of empirically determined and theoretically calculated heat values was performed. The change of regressive coefficients can be determined by the nature of Hess law (eq. 1) what was investigated and the attempt of its explication and validation was done.

Aug 1, 2013

By C. H. Stockwell

THE Eastern Townships of Quebec have been the chief Canadian source of chromite. Production, however, has never been large and, except for a period of steady but small output between 1894 and 1909, mining has been active only in war time. The known deposits are too small or too low grade to compete with overseas sources in normal times. During the last war, shipping difficulties and a greatly increased demand in the United States resulted in high prices and a ready market for low-.grade material. The Quebec chromite industry flourished and played an important part in relieving the wartime shortage. Shipments in 1918 .amounted to 15,600 tons of crude ore and 6,400 tons of concentrates. At the outbreak of the present war it was natural to turn again to the Quebec field as a possible source of this strategic mineral. Some of the old properties have since been opened by private and government money and some new deposits have been found. Total mill capacity is 750 tons per day, as compared with 200 to 300 tons in 1918. During 1940, 1941, and 1942, about 85 chromite deposits were examined by the Geological Survey in a belt 100 miles long and up to 7 miles wide. A part of this belt, about 35 miles long, in which the geological features ?were not well known, was mapped on a scale of 1/2; mile to an inch.? Small ..areas around some of the deposits were mapped in detail, on scales of 20 to 200 feet to an inch. Some geophysical work was done but did not result in the discovery of ore. Prospecting by stripping and trenching was then undertaken and chromite ore was uncovered at several localities. The above work was done by the writer and by J. W. Ambrose, who has kindly contributed his results for incorporation in this paper. Y. O. Fortier actd as assistant in the geological work and, in 1942, was in charge of a sub-party engaged in geological mapping. The author is indebted to H. C. Cooke and J. W. Ambrose for reading the original manuscript and for offering many helpful suggestions for its improvement.

Jan 1, 1944

By F. T. Manns, G. Harper

"The Swayze gold mine is an Archean vein deposit in northern Ontario. The veins are superimposed on a conjugate joint system and are contained within an anastomosing alteration envelope in a metadiorite body. Reserves were estimated on the basis of fire assays of channel samples and car load samples from underground mine openings, surface and underground diamond drilling and surface trenching. A semi-variogram constructed from channel samples along one of the drifts yielded a horizontal, regionalized influence of approximately 9.0 m. Common industry practice has been to use 6.1 m for similar deposits in Ontario. Proven ore was defined from underground openings. The maximum extrapolation distance for proven ore along strike and dip from a data point is taken to be 6.1 m. Probable ore is extrapolated 7.6 m from a data point in a mine opening or from a drill intersection. Possible mineralization is based on geological continuity one-half the distance to a neighbouring data point.The mineral inventory estimate of 1.45 million tonnes at a grade of4.8 g Au/tonne gives an excellent outline of the geology of the deposit. The deposit contains 313 000 tonnes of ore reservesat a fully diluted grade of6.9 g Au/tonne. These figures include dilution for several reasons: (I) a 2.1 m mining width is used rather than the more typical 1.5 m width to allow for over break because of the shallow dip of some vein zones; (2) over break is allowed for adjacent to major unmineralized dykes; and (3) grams of gold are deleted from estimates to allow for the mining of unavoidable minor dykes.A personal computer with off-the-shelf software was used to compile 712 geologically defined ore blocks and sort them into a number of revealing categories. The computer was used to perform grade sensitivity tests, as well as to evaluate depth potential. Hopefully, the reiterative aspect of the method has randomized the errors and helped to cancel their effects."

Jan 1, 1987

By Michael L. Free

The hydrometallurgy curriculum for undergraduate students at the University of Utah has evolved to contain a variety of tools to help students understand and apply hydrometallurgy in a context that has industrial relevance. In order for students to perform as engineers in an industrial hydrometallurgy setting, they need to understand thermodynamic and kinetic fundamentals and be able to apply these fundamentals to extraction, concentration, and recovery applications. Students must also understand related environmental, economic, and assessment issues in hydrometallurgy and be able to work with others. In order to meet these needs, the hydrometallurgy curriculum includes a variety of relevant subject information, on-line resources, laboratory experiences, and team work opportunities to help prepare students for careers involving hydrometallurgy. The development and use of these resources will be discussed in this paper.

Jan 1, 2014

By C. Jay Hodgson, P. J. MacGeehan, T. Sanders

"The orebodies of the Campbell and Dickenson mines are localized within an anomalously fissile and deformed zone that transects the eastern margin of a dominantly mafic volcanic complex close to its contact with a synchronously formed sedimentary basin containing clastic and chemical sedimentary rocks. The ore zones are mainly quartz-carbonate fissure veins and siliceous replacement zones formed during deformation and metamorphism, although there are some syn-volcanic exhalative ore zones in the mines. On a regional scale, the volcanic rocks have been affected by syn-volcanic spilitic alteration which has involved the leaching of Fe, Mg, Au and As from, and the addition of Na and variable amounts of Si to bleached zones enveloping primary permeable structures in the rocks. The leached constituents were deposited on the contemporaneous sea floor as iron-rich chemical sedimentary rocks. Although this alteration is not closely related, spatially, to the ore zones, it is characteristic of the general environment, and may serve to distinguish gold-prospective from gold-barren areas on a mining-camp scale.Closely associated spatially with gold deposits is a zone of feldspar-destructive alteration within which the volcanic rocks are characteristically feldspar-free, enriched in As, Au and to a variable degree in Si, and depleted in Na, Ca and to a variable degree in Mg, Fe and K. The alteration zone is also characterized by abundant, variably transposed, small quartz-dolomite to ferrodolomite veinlets formed during deformation and metamorphism, and includes, but extends outside of, the anomalously fissile zone hosting the orebodies. The alteration zone is interpreted to have formed syn-volcanically within the upper part of a major submarine hydrothermal discharge zone."

Jan 1, 1982

By D. A. Pirttinen

The promotion of improved coal quality for thermal generation can benefit our national economy. The construction of electric generating facilities in Canada is expanding at a rapid rate to satisfy the demands of a rising population and new uses for electrical energy. With remaining economic water power resources in the process of development, generation from thermal sources continues to grow. The increase in thermal capability has been somewhat arrested by a de-pressed economy, widening of inter-provincial and state transmission networks and decisions to exploit certain water resources before high capital investment is further in-creased by rising construction costs. The introduction of extra high volt-age transmission lines will further delay thermal generation planning, but in due course, when the effects of restrictive factors have been dissipated, steam-electric generation from fossil fuels will rise to considerable proportions. In time, nuclear sources will contribute a growing share to thermal power, but, it is doubtful if nuclear participation will ever displace conventional fuels for steam rising, unless it can be adapted to operate efficiently for variable outputs in peaking service. It appears certain that fossil fueled

Jan 1, 1961