Search Documents

By Robin N. Adair

Abstract -The Halfmile Lake stratiform volcanogenic massive-sulfide deposit consists of pyrrhotite­ rich breccia-matrix sulfides and pyrite-pyrrhotite-rich layered sulfides that form a laterally continuous sheet stratigraphically underlain by an extensive pyrrhotite-chalcopyrite-quartz stringer zone. Mineralization is hosted by a sequence of felsic pyroclastics and volcanic-derived, fine-grained metasediments. The proportion of volcanic to sedimentary rocks indicates increasing vent proximity from southwest to northeast across the deposit area. Fine- to medium-grained felsic pyroclastics and roughly equal amounts of fine-grained metasediments comprise the stratigraphic footwall to the mineralization. Quartz-feldspar porphyritic bodies cut this sequence and may have provided the heat source for exhalite activity. Felsic tuffs, locally crystal-rich, and lesser amounts of metasedimentary rocks make up the immediate stratigraphie hanging wall. This sequence is stratigraphically overlain and locally interfmgered with matie volcanics that contain substantial proportions of felsic fragments. Deposition of sulfides post-dated the beginning of felsic volcanism, which places the deposit in the middle of the Lower Tetagouche Group. Compositions of the volcanic rocks range from basait to rhyolite and exhibit sub-alkaline affinities. Strongly overprinted whole-rock, trace-element, and REE geochemical signatures resulting from mineralizing hydrothermal activity confirm the genetic relationship be­tween the stringer zone and the mineralized sheet. Large-scale D1 folding has overturned the entire sequence. D1 thrust faults and related sheath-like folds have profoundly affected sulfide distribution. D2 is manifested by a penetrative S2 foliation, and D3 is represented by large-scale open folds.

Jan 1, 1992

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Abstract-Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed surficial mapping and sampling programs in the Separation Lake area of northwestern Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of surficial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these surficial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t) values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sulfide mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from surficial samples was compared with that of in situ material. Gahnite from the peraluminous rareelement granite and pegmatite overlapped very well with surficial gahnite of Group 1. Gahnite from volcanogenic massive sulfide mineralization and Sedex-type mineralization overlapped well with surficial gahnite of Group 2. These results suggest that determination of gahnite composition in indicator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By J. C. Marchand, M. A. Berube

"L&apos;objectif principal recherché lors du broyage d &apos;un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d&apos;obtenir un produit de broyage d&apos;une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n&apos;entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu&apos;à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d&apos;analyse d&apos;images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s&apos;avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l&apos;on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d&apos;autres applications, et il permet de plus une grande souplesse d&apos;utilisation puisque l&apos;on a qu&apos;à construire des algorithmes de mesure et de calcul en fonction de l&apos;objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d&apos;illustrer la technique."

Jan 1, 1983

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed sur?cial mapping and sampling programs in the Separation Lake area of north-western Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of sur?cial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these sur?cial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t)values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sul?de mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from sur?cial samples was compared with that of in situ material. Gahnite from the peraluminous rare-element granite and pegmatite overlapped very well with sur?cial gahnite of Group 1. Gahnite from volcanogenic massive sul?de mineralization and Sedex-type mineralization overlapped well with sur?cial gahnite of Group 2. These results suggest that determination of gahnite composition in indi-cator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

Why A Friction Hoist? B EFORE discussing the equipment, it would be instructive to review the factors that influenced the management of Opemiska Cop-per Mines to purchase a friction hoist rather than a conventional double drum hoist. The mine required that 250 tons per hour be hoisted from a depth of 2,100 feet. They also specified that the top speed should not exceed 1800 feet per minute. Eight ton capacity skips in balance and a maxi-mum hoisting speed of 1725 feet per minute would meet the required <Output on a duty cycle as follows: Loading time Creep away from loading pocket Accelerate (at 2.5 ft/sec2) 10 seconds 5 seconds 11.5 seconds Full speed run Decelerate (at 2.5 ft/sec2) Creep into dump Cycle time Trips per hour Tons per hour 72 seconds 11.5 seconds 5 seconds 115 seconds 31 31x8 = 248

Jan 1, 1962

By A. S. Bayne

THIS paper will present a review of the mining operations of one of Canada&apos;s most lately established gold mining districts (1). The history of the Little Long Lac and Sturgeon River areas is interesting in view of the fact that, although they have long been the scene of a certain amount of mining activity, they remained little more than an uninhabited wilderness until 1933, since which time ten producing gold mines and mills have been established in permanent operation, eight of these having entered production since the beginning of 1937. As complete a background as possible will be given concerning the major influences having a bearing upon living and economic conditions in the mining communities. The object, here, is to show the diversity of problems which demand the attention of the operator starting up and operating a new mine in present times, and to indicate the ways in which these problems are successfully met in this district. A description of the power facilities and plant equipment will be followed by a summary of the problems encountered and methods applied in exploration and development. This is to aid in forming a background showing the circumstances which influence the mining methods and costs of the various operations. The paper will conclude with a description of the mining methods used and the costs of the operations, including summarized analyses of the stoping methods and mining conditions. The various phases of operation will be dealt with separately, in so far as this is possible, in order to present clearly the salient features. It is necessary, however, that the reader bear completely and constantly in mind the fact that in actual operations these phases arc, to a large extent, intimately related and greatly affect each other, as well as being, in turn, affected by other circumstances beyond the control of the operator. A few of these circumstances are: capital available during the development period and early stages of productive operation; strength of rock comprising the ore and its boundary walls; grade, size, shape, and location of ore-bodies; and many other natural items which must be carefully weighed in relation to the details of operation.

Jan 1, 1940

By A. F. Sirianni

The Peace River iron ore deposit represents the sole source of raw material for an integrated steel industry in Alberta. The ore has proved refractory to beneficiation by a number of techniques. A selective oil-phase agglomeration technique is described. Medium-grade concentrates, analyzing 48-53% Fe and 10-14% SiO2 were obtained with recoveries of about 75% of the total iron. These results appear to represent the optimum possible for this ore body.

Jan 1, 1977

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level position is then calculated from these pressure readings using an equation which includes the bulk density in the froth and bubbling zones. The precision with which the level is detected depends on how well these density values represent both zones. The calculation of these bulk densities from theoretical considerations is not possible and, therefore, the practice is to estimate them by calibration. Unfortunately, the calibration parameters often do not report the level with an acceptable accuracy. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the bubbling and froth zones. This probe can be used to detect the position of the interface to an accuracy of± 5 cm. The probe can be used while the column is in operation, which allows the on-line calibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 min diameter) are described.

Jan 1, 1989

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By Roger M. Jones

This paper comments on developments in bulk shipping which will be of direct interest to those who are considering the shipment of dry bulk minerals out of Nova Scotia by water. Various conveying systems, and the slurry system of loading, are considered, and the role of deep water ports as a catalyst to other industries is stressed.

Jan 1, 1971

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability. The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employes to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed."

Jan 1, 2002

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By A. M. S. Hussein, B. E. Rogers

Progressively more stringent emission limits and advances in regulations and enforcement have made air compliance more difficult for metallurgical facilities. This has historically required improved collection and treatment of stack sources. Fugitive emission reductions are now increasingly required to achieve compliance. Typically small in magnitude, fugitive emissions have a disproportionate impact on ground level concentrations, can be visible to the public and can influence workplace health and safety. Moreover, these emissions are complex, as they are spread over multiple sources, distance and time and are affected by various activities and conditions. As such it is difficult to find, define and monitor these emissions and their impacts. This difficulty translates to the design of emission reduction measures and operational requirements. This paper presents an overview or ‘heuristic’ of fugitive emissions management for compliance in existing operations. This includes aspects such as the impact of regulations on project scope, approaches to developing a comprehensive emission inventory, considerations for solution development and the plant’s role in sustaining compliance once achieved. Case studies are presented to demonstrate how portions of this approach have been applied.

Jan 1, 2015

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation&apos;s largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR&apos;s Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET&apos;s file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

Surfaces forces have been measured between gold sphere and gold-coated glass plate in xanthate solutions using an atomic force microscope (AFM). The measurements conducted in potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) solutions showed long-range hydrophobic forces, with the force curves showing no evidence for nanonubbles on the surface. The strongest hydrophobic force was measured at contact angle of 94° with a decay length of 23 nm. The hydrophobic force became weaker at higher concentrations and after a long immersion time, which may be attributed to the xanthate species adsorbed on top of the first mono layer. The hydrophobic force became stronger when the residual xanthate solution is displaced by pure water, indicating that hydrophobic force becomes the strongest in pure water.

Jan 1, 2009

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015