Search Documents

By Martin Kesting

The world wide growth dynamics and the continuously growing demand for energy, results in increasing energy prices. Looking from this point, the efficient exploitation of fossil fuel deposits has become a more important factor to the production of energy raw materials than ever before. This shall be reached by an increase of the automation degree of the bucket wheel excavator in the open pit mining as well as a quality increase of the entire mining process chain. A further optimization of this operation can only be achieved by gathering additional information about the input parameters. The earlier and more exact the description of the input parameter, the greater the effectiveness of the entire process chain. To address this major issue, the RWE Power AG assigned the Institute for Transportation and Automation Technology with the research project "SIMT, Sensory Identification of Material Type and Detection of the Interfaces" [Kes07]. Presently, the control of the bucket wheel excavator is carried out manually by the operator, as well as the visual identification of the different geological layers and the energy raw materials. In this paper, a sensor-system is introduced, which was developed in order to transfer the manual material identification and detection of interfaces into an automatic online procedure. A special challenge and the main focus of this contribution is the integration of this sensor system into a bucket of the bucket wheel excavator. For measuring procedures where direct contact with the in situ material is necessary, the sensor has to be integrated into the bucket. Since direct contact with the material is not necessary, it can be integrated next to the bucket wheel. The results of a preliminary study show that although there is a broad spectrum of sensor technologies for material and interface identification, only a few are suitable for an application in on-line measuring at the bucket wheel excavator. Taking into consideration the demands on the sensor technology, the studies carried out and comparable applications of individual sensor technologies which have already taken place in practice, the integration of the following measuring systems have been realized: ground penetrating radar / reflection measurements, geo electric, resistance geo electric technology. The solution developed in the research project offers for the first time the direct integration of sensor systems into the bucket of a bucket wheel excavator. It will now be possible to test other measurement methods and sensors, not only for the ones already mentioned. As an example the integration of a triaxial accelerometer to measure the solid borne sound and vibrations concerning the cutting of different materials will be shown.

Oct 1, 2009

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By Craig Naudé

"An enhanced gravity concentrator was installed in conjunction with an Intensive Leach Reactor at the Sadiola plant in Mali last year and commissioned in Dec 2007.There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every 10% of gold recovered by gravity, there was a corresponding 0.1% to 1% additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall 4% gain in plant recovery.With total gold recovery of 12% in the gravity section, grades are increased from 3.54g/t in the gravity feed to an average of 2 600g/t in the concentrator feed to the in-line reactor. The recovery of gold in the in-line reactor is in excess of 98.5%.This paper discusses the background to the project, the laboratory testwork prior to the equipment selection, the operational results of the system, as well as the benefits of the future application of high mass yield centrifugal concentrators in base metals, sulphides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONBesides picking nuggets off the ground or out of riverbeds, gravity concentration is arguably one of the oldest methods of recovering gold. In circa 6000BC people discovered that gold can be found behind the rocks and in depressions of creek beds. By placing rocks in a stretch of channel with the proper slope the first sluice is built, probably around 4,000 BC, and this method is still practiced today."

Jan 1, 2009

By T. K. Dichmann, J. A. Finch

"Microflotation, laboratory batch, and in-plant minicell continuous tests were conducted to determine if copper ions not only activate sphalerite but also depress pyrite when the minerals are together. Microflotation tests showed that pyrite recovery increased with addition of copper ions in the pH range of 5-10 when alone, but decreased when sphalerite was also present. Batch flotation tests (Red Dog ore) showed that upon addition of copper, pyrite recovery decreased significantly. The continuous tests (Louvicourt Mine) confirmed this and indicated that with excess copper pyrite recovery can increase. The results suggest there is competition for copper and xanthate in favour of sphalerite. To take advantage of this competition it may be necessary to control the sequence and rate of copper, collector, and lime addition. INTRODUCTIONFlotation, in common with all physical separations, is an imperfect process that results in misplacement of minerals. One source of this imperfection is accidental activation by contaminating metal ions. An important practical example is the misplacement of pyrite to zinc concentrates. Flotation of sphalerite generally requires activation by copper ions, added as copper sulphate. Copper ions are also used to activate pyrite [l] hence there is the suspicion that accidental activation contributes to the recovery of pyrite (Py) with the sphalerite (Sp). However, recent literature has shown that copper ions may make Py less floatable if Sp is also present. Xu et al. [2] conducted continuous minicell tests in-plant at Kidd Creek Operations (division of Falconbridge Ltd.) and showed that while the addition of copper sulphate improved zinc/iron selectivity, it did so as much by reducing the recovery of pyrite as increasing zinc recovery (Figure 1)."

Jan 1, 2000

By Robert B. Parsons

"Canada's mining industry has reason to celebrate the federal government's budget which was tabled on February 26, 1986. The budget contains an important proposal to improve the flowthrough share rules by effectively eliminating the investor's liability to third parties. This proposed rule change and other important budget proposals are the subject of this month's edition of Tax Notes. IntroductionWhile Finance Minister Michael Wilson's February 26, 1986 budget received a mixed reaction from business and labour leaders, the budget was mainly ""good news"" for the mining industry. A long-standing bugaboo in the flow-through share rules will be cleared up, a permanent set of rules will be installed for the tax treatment of Northern allowances, and limited partnerships will apparently be able to continue to serve a useful role in financing exploration programs. Flow-Through SharesThe present rules which apply to an investment in flow-through shares are structured in such a way that the relevant Canadian exploration expense (""CEE"") must be incurred by the investor, and not by the issuing corporation. Obviously, in the case of most flow-through share issues, this requirement that the investor incur the CEE poses a practical problem-the investor typically does not have the expertise or organization to incur the CEE. As a result, an integral part of most flowthrough arrangements is an agreement whereby the investor appoints another party (usually the issuing corporation) as his agent to spend the flow-through funds on CEE on his behalf. Although the issuing corporation might consequently be the party which actually spends the flow-through share funds on CEE, nevertheless the legal structure is such that the investor is the ""principal"" who is incurring the CEE. As such, the investor is legally responsible for any third-party claims with respect to the exploration program. Third-party liability might arise, for example, in the case of property damage, personal injury, environmental infractions, and so on."

Jan 1, 1986

By Jesse L. Duke

Outline ?Understanding the context ?The Business, political, social and legal environment ?Recipes for Success (three Ps) ?Develop effective Partnerships/relationships ?Plan carefully ?Actively Manage the ?Process? Business Environment ?Nunavut?Impressive mineral potential ?Emerging diamond industry ?Dominated by Juniors ?NWT ?Maturing Diamond industry ?Emerging oil and gas industry ?Yukon ?Alaska Highway Pipeline ?Junior-dominated exploration and development ?Growing acknowledgement in Canada of the importance of northern resources ?Shift of thinking: north-south infrastructure (vs. East-west)

May 1, 2006

By Patrick J. Williams, Peter J. Pollard

"Abstract - Enigmatic hydrothermal vein/breccia/replacement Cu-Au deposits with magnetite and/or hematite are well-represented in Australian 1850 Ma to 1500 Ma terrains and associated with different-aged synorogenic intrusions in the Tennant Creek Block (ca. 1850 Ma); the Gawler-Curnamona region (1640 Ma to 1590 Ma); and the Cloncurry district (Mount Isa Eastern Fold Belt, 1540 Ma to 1500 Ma with a possible earlier event at ca. 1600 Ma). No deposits are known to be coeval with various 1780 Ma to 1610 Ma anorogenic intrusions. Deposits are hosted by many different rock-types with varying metamorphic grade including granites and various supracrustal rocks. Depth of mineralization varied from many kilometers in semiductile crust (e.g., Cloncurry deposits) to very shallow (e.g., Olympic Dam). Ore deposition near Cloncurry occurred in brittle-ductile shear zones from geochemically variable and complex, CO2-rich, 300°C to 500°C, high salinity fluids with magmatic stable isotopic signatures. Recently published studies of a giant granitoid-hosted magnetite vein complex at the Lightning Creek prospect (>1000 Mt magnetite) suggest it is a product of internal differentiation and endogenous Fe and Cu-rich hydrous-carbonic fluid phase generation within a quartz monzodiorite-monzogranite intrusion. Coupled with other field relationships, this points to a possible genetic relationship with intermediate (55 to 65 wt% SiO2) members of an alkaline and partly shoshonitic granitoid supersuite which appears to have both mantle and crustal source components from ?Nd evidence. In constrast, main-phase mineralization at Olympic Dam in the Gawler Craton is distinguished by hematite-phyllosilicate alteration and chalcopyrite-bornite-chalcocite zoning, reflecting fluid mixing in a high level (<250°C) system with a probable large component of meteoric water. Early high-temperature parageneses and fluid inclusions imply that the extensive hematitic breccias overprinted an older magnetite system which may have had similarities with those at Lightning Creek and Ernest Henry in the Cloncurry district.Deposits of this family are inherently difficult to find and evaluate as even within a single district, there is no reliable relationship between the location of ore and any specific combination of geophysical characteristics. Diverse alteration assemblages, geochemistry and physical characteristics suggest the deposits reflect the interaction of multi-sourced fluids with different host rocks in a wide range of geological environments. Recent discoveries and research in the Cloncurry district have extended the range of deposit models available and aid the development of a rudimentary classification in which economic and exploration characteristics can be linked to variations in the mechanisms and environments of ore formation."

Jan 1, 2001

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine&apos;s central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine &apos;s central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month&apos;s power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which &apos;complete the cycle&apos; of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By D. Laguitton, D. Hodouin, V. K. Gupta, R. Spring

"The CANMET SPOC project aims at inducing progress in process evaluation and optimization by developing user oriented software based on state-of-the-art theory. The present work is the result of a joint effort by CANMET, Noranda Mines and Université Laval to develop two computer packages: one (RTD) to calculate the residence time distribution that best describes the material transport through the mill, the other (FINDBS) to estimate the rate of breakage and distribution function of the population balance model in a ball mill. The RTD package can handle data from various experimental methods (impulse or complex tracer feed, with or without recycling, etc...). The FINDBS package provides options for the functional description oj both model parameters Band S. The full detail of the methods and programs appears in a users guide. The program capabilities and several sample runs are presented.IntroductionSimulation of mineral dressing operations by computer has been largely contained within academic and research circles and has not yet gained a status of routine practice in the ore and coal industries. It is however a matter of time before process simulators are available on every process engineer&apos;s desk to assist process optimization tasks, flowsheet design and professional training. The CANMET SPOC project (Simulated Processing of Ore and Coal) was initiated in 1980 to assist the Canadian industry in integrating computer-based methodology for process evaluation and optimization(1). Software development, documentation and transfer is one of the main priorities of the project which will mature in 1985 by releasing a complete package of manuals and programs covering sampling, material balance computation, unit modelling, flowsheet simulation and optimization . This paper is a condensed description of a typical project element in its 1982-1983 state of development. The required methodology for ball-mill modelling and simulation was consolidated an d merged to other project elements during a joint study under contract financed by CANMET and Noranda Mines Ltd . The first part of the study dealt with documenting experimental methods and software for ball-mill computer simulation. Université Laval GRAAIM (Goupe de Recherche en Automatistion Appliquée à l&apos;Industrie Minérale) acted as sub-contractor for this part of the study(16,17). A second part dealt with applying the model calibration techniques to a large industrial data base and is reported elsewhere(2,18,19)."

Jan 1, 1984

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By Bruce Mennie

PT Freeport Indonesia (PTFI) operates copper and gold mining operations in a mountainous area of the Mimika regency, near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. The mining and concentrating operations typically produce 240,000 metric tonnes per day of Copper and Gold ore from the combined mining of an 80,000 tonne per day (ore) block cave operation (DOZ Mine) and a 160,000 tonne per day (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open pit mine will be complete in 2016 at which time PTFI?s operations will convert to Underground. Mining operations will transition from today?s mixed surface and underground operation to full underground mining over the next 6 years. This paper reviews the history of Redpath?s relationship with PTFI, beginning with a raiseboring contract in 1981 and evolving into vertical and horizontal development contracts of up to 37,700 equivalent metres of lateral development and 4,000 metres of vertical development in 2011. An overview of the current operations (PTFI?s Grasberg Open Pit and DOZ Underground Mines) and transition period (challenges for the transition from current to future underground mines) is presented with details of development of common underground infrastructure and future mines; Big Gossan Mine, DMLZ Mine, Grasberg Block Cave Mine, and the Kucing Liar Mine.

Oct 1, 2010

By Robert S. MacPhail, Chilombo Henry, Arnold Kabamba, David Mukelebai, Suresh Thirunagari, Bukali Victor, Yoram Kapai, Chomba Leonard, Kanna Amarasingham

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate. Developed by Charles Tennant & Co (Canada) Ltd and has shown improved collection properties over SIPX for sulphide minerals flotation. Improvement of recoveries, grades, faster kinetics, lower dosages, high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31. Recent plant trial carried out in the copper circuit at one of the largest copper mine in Zambia shown over US $ 2.00 Million annual improvement on the bottom line over SIPX at current copper prices. Data produced also showed superior grade and recoveries from rougher concentrates that previously had not been attainable with other reagents effectively. Flex 31 has also shown positive outcomes with zinc, Copper/Zinc, arsenopyrite and copper/molybdenum ores.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthate, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by the research division of Charles Tennant & Company (Canada) Limited has produced a chemically enhanced SIPX. This product has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The product was named “FLEX 31”."

Jan 1, 2016

By M. Sturzenegger

This paper documents a field survey using long-range terrestrial digital photogrammetry at the Palabora open-pit mine, South Africa, for multi-scale characterization of rock mass discontinuities. Stereomodels covering the entire mine were generated based on photographs taken from a distance of 1600m across the pit, using a series of f=20-400mm lenses. Details on the methodology used and its accuracy are discussed. Preliminary results on discontinuity orientation, persistence and intensity are presented, highlighting the effect of observation scale. The potential uses of long-range terrestrial digital photogrammetry in open-pit mine and large natural rock slope environments is emphasized. The use of an f=400mm lens from distances larger than 1.5km may represent an important step forward in the geotechnical characterization of inaccessible remote rock faces.

May 1, 2009

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 45 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the US and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Nov 1, 2011

By Michael Harley, E. Guy Charlesworth

"Abstract - Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim&apos;s Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim&apos;s Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By David M. R. Stone

Underground mining in the gold industry is gaining popularity in Nevada, and with it the use of cemented rockfill is becoming mainstream. Even with today?s high metal prices, however, mining companies are very sensitive to the margins they realize, and are constantly looking for ways to reduce costs or improve efficiencies. Given that the backfill is one of the largest cost centers in underground mining, mines are constantly under pressure to reduce backfill costs. This paper will present an overview of the factors that impact cemented rockfill quality in Nevada mines based on the authors many years of consulting experience. Cemented rockfill quality can be linked directly to binder consumption, hence programs aimed at improving quality generally result in lower binder costs, better performance in the fill (hence less dilution), and improved safety. The paper will conclude with the key elements of a comprehensive program of backfill quality assessments and backfill QA programs. Comparative laboratory and minesite data from a number of operating and proposed mines will be presented.

May 1, 2007

By D. P. McDonald

"IntroductionTHE PURPOSE of this paper is to present .a summary of the evidence given before the Petroleum and Natural Gas Conservation Board in support of applications to it for permits to export natural gas from Alberta.I will attempt to be objective in my statements, despite the fact that my main interest in the hearings before the Board was to advance the interests of my own clients, the Westcoast Transmission Company, Limited.The hearing of the export applications •commenced before the Board in January, 1950, with the .application of the Westcoast Transmission Company. Joint hearings were commenced in September, 1950, and completed on December 14th, 1951. The Board heard evidence in support of six applications for export, one application to build a gathering system in Alberta, and three interveners, the .latter being the City of Calgary, the local gas companies, .and the coal interests, including both operators of coal mines and the Unions.The evidence comprised better than 8,400 pages, over two million words, and occupied 92 days before the Board.The Interest in Natural GasThe natural gas industry is one of the newer industries. It is not yet twenty years •old. In the United States, the expansion •of pipeline facilities has been phenomenal in the last fifteen years, and particularly in the last three years, when a total of over two billion dollars was invested in pipeline facilities. There are approximately 250,000 miles of gas transmission pipelines in the United States at this time, with additional lines constantly being pressed."

Jan 1, 1952