Search Documents

By Floyd JM, Bultitude-Paul J

The development of a process for the extraction of antimony from materials produced by Greenbushes Tin Limited has been carried out based on theoretical and laboratory studies. The materials treated have included concentrates of tantalite and cassiterite containing antimony at levels ranging from 0.3% to 2%. Roasting under controlled atmospheres is required to stabilise Sb203 rather than the low vapour pressure metal or higher oxide. Sulphidising additives such as pyrite, pyrrhotite or sulphur give enhanced antimony removal from tantalite and cassiterite at roasting temperatures of 900¦ to 1100¦C. Substantial elimination of antimony to levels of 0.1% or less was Achieved.

Jan 1, 1986

By Shoobridge PH

Operating difficulties during 1977 with the Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at their Cockle Creek zinc-lead smelter were found to be caused by premature softening of sinter in the upper shaft of the furnace. This soft- ening was shown to be a consequence of raw materials and operating policies which led to unusually high levels of both lead and silica in a sinter of low basicity. A programme of softening tests and micro-examination of a range of sinters established that premature softening occurred when lead and silica increased to the point where a lead-calcium silicate with a low lime content became the major continuous phase in the sinter. This information was used to define a range of compositions which kept the softening temperature acceptably high for furnace operations.

Jan 1, 1978

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Freeman N

A microcomputer based control system has been developed and implemented at ZC Mines (now Pasminco Mining). The control system maximises throughput at a product size set point while maintaining a "safe" cyclone underflow and mill operating pulp density.To characterise mill and cyclone operation over a range of ore types, 60 circuit surveys were carried out by ZC Mines personnel over a period of four months. The data for each test were model fitted to check for data consistency and to accurately estimate circulating loads.The model fitted results were combined with instrument readings (including in-stream analysis probe assays) and the data checked for ability to predict key variables such as product size and underflow density from measurable inputs.In the resulting control scheme, panicle size and underflow density are not monitored directly, but are predicted by regression equation models based on directly measured variables. The tonnage control loop uses a dynamic model to maximise responsiveness.The system provides a data log output to an mM compatible personal computer at programmable intervals. Comparative data logging over a period demonstrates substantially smoothed circuit performance.The grinding control system was originally implemented using Fischer and Porter micro-DCI controllers. The program has also been implemented on a distributed control system using a sequence oriented programming language.

Jan 1, 1990

By Toivanen R-M, Leinonen O, Pekkarinen H

This paper presents developments in designing an integrated mine control system at Kemi mine. The aim of this paper is to present the general structure of the system and to outline some features of the process control strategies. The results o

Jan 1, 1998

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

Supergene nickel sulphide ore mined currently by Agnew Mining Company is at times partially oxidised to sulphate. The resulting soluble nickel, and calcium and magnesium in mill water, are shown to act as depressants in flotation. The depressant effect is favourably selective in that violarite, the main nickel mineral, is less affected than pyrrhotite. Nickel recovery, however, is adversely affected, probably through reduced flotation of complex sulphides. Soda ash consumption is increased markedly by the presence of the cations as shown by operating data and pulp titration tests. A significant increase in concentrate grade, from 9% to 14% Ni, was achieved late in 1981. One of the changes in plant practice which contributed to this improvement was the addition of soda ash to mill feed rather than to flotation feed as before. It is shown by laboratory tests that this reduced the depressant effects of the cations, thereby improving recovery at the expense of rougher selectivity, or equivalently, increasing concentrate grade at constant recovery. The selective depressant effect cannot be exploited until scavenger recovery is improved and a scavenger concentrate regrind-retreat äcircuit is implemented. Development is

Jan 1, 1978

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993

By X Ling, M Barati, E Moosavi-Khoonsari

In the pyrometallurgical process of secondary lead recycling, a desulfurising agent, such as Na2CO3 is added to minimise the emissions of sulfur into the atmosphere, while silica is introduced into the smelter as a fluxing material. Subsequently, a significant amount of Na2O and SiO2 remains in the downstream reverberatory furnace and blast furnace slags. However, there is limited understanding of the thermodynamic behaviour of silicate-based lead slags rich in Na2O, posing challenges in accurately determining the optimal condition for targeted metal recovery and final slag composition. In this work, the equilibrium phase relations of the PbO-Na2O-SiO2 system in the primary phase field of Na2SiO3 are studied from 800 to 1000°C via equilibration-quenching method. Samples with different compositions were prepared and held in platinum capsules in air at these temperatures to reach equilibrium. The equilibrated samples were subsequently quenched and the phase compositions were measured by electron probe microanalysis (EPMA). The results were then compared to those of previous studies and any discrepancies were resolved.

Jun 19, 2024

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

By Keele R. A

The Cambrian structure in the Mt Read Volcanics was produced by four deformational events: obduction of forearc-derived mafic/ultramalic complexes in the early Middle Cambrian, a middle Middle Cambrian extensional phase related to the post-collisional Mt Read volcanism and VHMS mineralisation, Middle Cambrian E-W folding, and Late Cambrian N-S folding and basin inversion. The major phase of VHMS mineralisation in western Tasmania is restricted to the very brief period of extensional tectonics within the middle Middle Cambrian. Within this period a N-S graben was produced with a complex series of transfer zones, largely striking E-W. Most VHMS mineralisation is restricted to the top of massive volcanic successions, with several mines close to Cambrian transfer structures. Many of the transfer structures continued to be active until the Devonian. The later compressional Cambrian events are not significant in localising orc formation. Within the Rosebery mine a complex pattern of minor Cambrian normal faults has a second order control on the distribution of the mineralisation.

Jan 1, 1997

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

By J Hadjigeorgiou

Narrow vein mining, as most types of mining, faces important geotechnical challenges. The specificity of geotechnical challenges in narrow vein mines stems from the nature of the deposits, which are often inclined, discordant and found within fractured rock or faults or in shear zones within country rock. This complicates the construction of representative geomechanical models and limits the applicability of several engineering design tools. Furthermore, in certain cases, the severity of encountered geotechnical problems is considerably greater in narrow vein than in wider orebodies. This paper provides an overview of geotechnical and other challenges in narrow vein mines with a focus on how these are currently addressed. Of particular concern is the use of manual labour working close to the mining face where there is greater exposure to geomechanical hazards. This review concludes with a particular emphasis on understanding the limitations of commonly used engineering tools and techniques to address geotechnical problems in narrow vein mines.CITATION:Hadjigeorgiou, J, 2012. Geotechnical challenges in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By N Power, A D. Costar

There has been significant growth in mining and energy exploration in South Australia, which has identified new major potential opportunities. This sector generates significant economic value to the state and their support remains a priority for the state government. The delivery of this economic and associated community value to the state is dependent on the mining and energy sector being able to access reliable water supplies.The vast majority of priority areas for the mining and energy sectors are located in areas that have traditionally been of low priority from a water-use perspective and hence, data and knowledge levels are generally low.Recent studies have identified a potential increase in demand for water in the mining and energy sector for potential developments from approximately 40 GL to over 170 GL over the next ten years. The studies found that water and water infrastructure is the second highest proportion of planned infrastructure capital investment by resource companies. The South Australian GovernmentÆs Plan for Accelerating Exploration (PACE) initiative (PACE 2020), also identifies addressing the issues of location, use and management of South AustraliaÆs water resources as a key priority for the growth of the mining and energy sector.The Department of Environment, Water and Natural Resources (DEWNR) has developed the facilitating long-term outback water solution (FLOWS) initiative. DEWNR is currently undertaking a suite of programs to provide groundwater information at the regional scale to better target water supply options for mining and energy developments and community water supplies.The Goyder Institute for Water Research has leveraged significant research investment of $3 M to develop methodologies to interpret airborne geophysics to map groundwater sources.The FLOWS Initiative will provide key content for the PACE Water Program and will also assist in the development of water supplies for remote far north communities by identifying alternate groundwater sources to improve water supply security.This paper will discuss how developing an appropriate science and knowledge base will encourage and secure development where appropriate, enable prudent decision-making and policies regarding water allocation, accounting and licensing, whilst ensuring the protection of environmental assets.CITATION:Power, N and Costar, A D, 2013. Finding long-term outback water solutions, in Proceedings Water in Mining 2013 , pp 191-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Singh RN

Monolithic packing systems have gained in popularity as a gate side packing method. However, there has been no detailed investigation to assess their underground strength behaviour. This work includes the laboratory and in situ investigation for strength behaviour determined on various monolithic packing materials namely Tekpak-XX, Hydropak-20, Hydropak-30, Astrapak-3R, Flashpak, Thyssen pack and Aquablends. A simple technique for assessing the pack strength was developed at the laboratory by using a penetrometer, of which penetration resistance can be directly correlated with the uniaxial strength of the pack. The in situ strength investigations were made on core samples obtained from three pipes inserted inside the pack, while the penetration test were made on the pack surface. The in situ results indicated that the packing material develops an inconsistent strength on various part of the pack which was mainly related to an inadequate mixing of grouts inside the pack.

Jan 1, 1992

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986

The non-renewable energy resources of Queensland comprise coal, petroleum (oil and gas), oil shale and uranium. Coal is widely distributed., and has been developed extensively both for export and for use within the State. Proven reserves total 5 390 million tonnes recoverable of coking coal and 5 580 million tonnes recoverable of non-coking; very large resources particularly of non-coking coal are still to be quantified by further drilling. Annual production is of the order of 20 million tonnes of coking coal, principally for export, and 6 million tonnes of non-coking, mainly for power generation within the State. Petroleum resources are meagre in com- parison with those of coal. Initial recover- able reserves of liquids (mainly in the now substantially depleted Moonie Oil Field) totalled only 4.2 million m3. Initial recover- able reserves of gas (mainly in the western Surat and Bowen Basins) totalled 7 800 million m3. Annual production is of the order of 64 thousand m3 of liquids for refining in Bris- bane, and 268 million m3 of gas mainly for production of fertiliser and for industrial and domestic heating, in Brisbane. Prospects are fair for the discovery of additional reserves. Two deposits of oil shale are potentially of economic significance. The Rundle deposit at The Narrows in central Queensland has the

Jan 1, 1979

By Denby B

The ever increasing demand on land use has led to large areas of land being considered for development, which because of past mining activities are covered by substantial depths of fill materials. This paper examines the problem faced with the development of land infilled with open cast mining backfill, in predicting the behaviour of the fill upon development. To be able to design foundations suitable to withstand the movements that occur within open cast backfills or design a backfilling operation that produces land suitable for a proposed after development, a means of predicting backfill settlement is required. Factors critical to this prediction are the timing of backfilling operations, the compactive state of the backfill and the inundation of the backfill. The analysis of a considerable quantity of data collected from the monitoring of backfilling operations and backfill movement at a range of open cast coal sites located within the UK has given the authors a better understanding of how open cast backfills behave in terms of long-term creep settlement, collapse settlement and how these are effected by backfill scheduling. This knowledge has been encoded into a program running under Microsoft Windows that enables a user to make settlement predictions for a point, a given section or area or for the whole site. Differential settlements, critical to any development design, can also be determined between any two points taking into consideration the heterogeneous nature of open cast backfills. The program was tested with data from an open cast coal site in the UK. Compaction monitoring during the placement of the backfill material enabled a model of the backfill to be constructed taking into account backfill properties and scheduling. This model, taken as input into the program, enabled future backfill settlement predictions to be made. A comparison is given between these results and actual settlements obtained from a short-term settlement monitoring scheme.

Jan 1, 1995

The application of reinforcement techniques to enhance the stability of underground coal mine roadways subject to high stresses is discussed. Research conducted in the Illawarra Coal Measures has been aimed to delineate the factors which influence the behaviour of rock above roadways and the performance of the reinforcement placed. Design considerations for the reinforcement of mine roadways in the Bulli coal are based on a quantification of the rock response together with a reinforcement strategy to enhance the structural integrity of the roof strata.

Jan 1, 1986