Search Documents

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

By John K. Hammes, Stanley D. Michaelson

Generally, the mining costs reported for the large open-pit operations in the United States and South America lie within the range of $0.20 to $0.30 per ton of material moved. (These operations have strip- ping ratios ranging from 1.5 to 4.0.) Productivities for the larger North American properties are in excess of 200 tons of material per man shift, while those for the South American operations are less than 200 tons per man shift. The most significant variations in cost are in the categories of haulage and general mine cost. Haulage costs vary, as expected, according to the mine elevation, pit profile, crusher location, and accessibility of a dump area, and general cost variations depend largely on the overhead cost items included in this category. Drilling and Blasting Practice The majority of open-pit copper mine production drilling is performed by rotary drills. Hole diameter varies from 6 in. to 12 in., with 9-in. holes being most common, and penetration rates vary from 35 ft to 60 ft per hour.

Jan 1, 1968

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

By E. C. Carris

THE particular field of application of machines utilizing air cur¬rents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful com¬mercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the Ameri¬can Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Heyl and Patterson oscillating table, 199.7. 4. "Stump Air-Flow," pulsating air jig, 19391. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAN TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corpora¬tion, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943

By J. G. Faller, L. P. Skolnick

The distribution of cobalt and vanadium over non-equivalent crystallographic sites in C14-type Zr(VCo), alloys has been investigated. An anomalous X-ray scattering technique developed by Skolnick, Kondo. and lavine7 by which the separation in the scattering factors of two similar atoms can be enhanced was employed. Six alloys spanning the pseudobinary section ZrV1.6Co0.4-ZrVO.6CO1.4 at 10pct steps showed a nonrandom compositionally dependent distribution. Specifically, at high vanadium content cobalt preferentially occupied sites of type (6h) and vanadium, sites of type (2a; at low vanadium content the reverse was observed. In addition to the distribution fraction the structural parameters x and z were obtained. There was no significant deviation of these parameters from those obtained in the ideal C14 structure. Certain suggestions are made to account for the observed nonrandomness in the distribution of atoms on the two types of sites. INTERMETALLIC compounds of formula AB2 iso-morphous with MgCu2, MgZn2, and MgNi2 are known as Laves phases. Because Laves phases exhibit high symmetry and coordination numbers, the highest possible for an AB2-type compound,1 they are among the most frequently observed compounds in nature. In recent years interest has centered about the purely transition metal Laves phases2-' in efforts to understand the function of atomic size and electronic structure in the formation of these compounds. It has been observed that pseudobinary Laves phase systems often show a variation of structure across the phase diagram. Such a system is the ZrV2-ZrCo2 in which the structure varies from cubic MgCu2 to hexagonal MgZn2 to cubic MgCu2.4 Some understanding about the conditions under which the second modification is stable can perhaps be gained by studying the distribution of cobalt and vanadium atoms on lattice sites in the MgZn2 modification of the system ZrV2-ZrCo2. In both the MgZn2 and MgNi2-types there exist nonequivalent positions open to occupancy by the B element, whereas in the MgCu2 prototype all sites are equivalent. Skolnick, Kondo, and La-vine7 have developed an anomalous scattering technique suitable for this type of investigation. Whereas the influence of size on the formation of a Laves phase is well recognized, no substantial evidence has been put forth in support of the size ratio dependence of a particular prototype. Berry and Raynor8 suggested that RA /RB ratio does indeed affect the type of structure that is chosen, MgZn2 compounds tending to cluster about 1.225 while MgCu2 compounds were found at larger deviations from this ratio. Dwight,3 however, from a study of 164 Laves phases does not believe this generalization to be justified. Electronic effects are certain to play a part in the stability of Laves phases in general and in the choice of a structure type in particular. For example, size along would favor the formation of Laves compounds of Ti, Zr, Hf, Ta, or Nb as the A element with nickel or copper as the B element. The absence of such is attributed to an unfavorable electron : atom ratio by Elliott and rostoker.4 Early experiments of Laves and witte9 with pseudobinary and pseudoternary systems of the three prototypes established the dependence of crystal structure upon electron: atom ratios. They observed that the MgCu2 structure dissolved elements of higher valency until the electron: atom ratio of =1.8 was reached; the MgZn2 likewise dissolved elements of lower valency replacing zinc. witte,6 from calculations of the electron : atom volumes of Brillouin Zones, obtained limits of stability for the prototypes MgCu2 and MgZn2. Elliott and Rostoker4 used these limits with considerable success in the all-transition element Laves phases they investigated. According to witte,6 compounds between the electron :atom ratios of 1.80 and 2.32 were of the MgZn2 type; those above and below exhibited the MgCu2-type structure. On the basis of these limits and an assumed valency of zirconium based upon the near tetra-valence of titanium, Elliott and Rostoker obtained valencies for the first transition series elements. For the Laves phases with which this investigation is concerned, ZrV2 and ZrCo2, the authors calculated electron :atom ratios of 2.54 and 1.56, respectively. These ratios are for the MgCu2-type structure and straddle the stability band of the MgZn2 modification. One could, therefore, predict that a pseudobinary system ZrV2-ZrCo2 should pass through the MgZn2 modification in traversing the composition diagram from one end to the other. Implicit in this assumption is a smooth change of the electron: atom ratio from 2'54 to 1.56. MOSS10 states that his finding the low temperature structure of ZrCr2 to be C15 instead of C14 alters greatly Elliott's valency of zirconium and hence the assumed valencies of the other metals. Such a quantitative correlation of structure with electron : atom

Jan 1, 1963

By AIME AIME

WITH a brilliance undimmed by hard times, the annual dinner on Wednesday evening, Feb. 17, was a complete success. More than 600 members, friends and ladies gathered early and filled the anterooms of the grand ballroom of the Commodore Hotel, while the president's reception was in progress, and then at the sound of the gong and with the music of the orchestra, rising above the happy din of conversation thronged to their seats at the tables. Following the "potage Ambassadeur"-probably to eliminate a very real hazard-the usual toy balloons appeared and a gay and lively scene, punctuated by multitudinous explosions, ensued, as the hundreds, of variously colored spheres bounced yon and hither until their gaseous existence was ended on the glowing end of a cigar or cigarette. On the speakers' dais sat C. E. Beecher, Chairman Petroleum Division; J. Vipond Davies, representative of A. I. M. E. on the Alfred Noble Prize Committee; Corbin T. Eddy, Alfred Noble Prize recipient; A.' S. Tuttle, Vice-president American Society of Civil Engineers; W. C. Mendenhall, Director U. S. Geological Survey; George C. Bateman, representing the Canadian Institute of Mining and Metallurgy; Paul D. Merica, Institute of Metals lecturer and Chairman James Douglas Medal Committee; Champion Herbert Mathewson, James Douglas Medalist; Robert E. Tally; retiring President; G. Temple Bridgman, toast-master; Scott Turner, incoming President; F. W. Bradley, William Lawrence Saunders Medalist; Fred Searls, Jr., Chairman William Lawrence Saunders Gold Medal Committee; Arthur Notman, President Mining and Metallurgical Society of. America; Robert J. Grant, Director U. S. Mint; Landon F. Strobel, Chairman New York Section; Howard Scott, recipient of Robert W. Hunt Prize; George. B. Waterhouse, Chairman Robert W. Hunt Prize Committee; F. M. Becket, Chairman Iron and Steel Division; Ora E. Clark, recipient of the J. E. Johnson, Jr., Award; Richard Peters, Jr., Chairman J. E. Johnson, Jr., Award Committee; E. C. Bain, Howe Lecturer; Sam Tour, Chairman Institute of Metals Division; and H. Foster Bain, Chairman. Charles F. 'Band Foundation Committee. ' Each was heartily applauded when introduced by Mr. Bridgman, as was Mrs. Tally, who also made a bow. The toastmaster made graceful reference in introducing Mr. Strobel, to the large part the latter had taken in planning the meeting.

Jan 1, 1932

By Alexander Anderson

TABLES showing the drift and inclination of wells surveyed in the years 1924 to 28' and in the year 1929' have already been published. Each of these tables included a little over 1,000,000 ft. of rotary hole. In the year 1930 the table -shown-in . Fig. 1, comprising, the results of surveys .of 1,030,344 ft. of hole and representing 11,642 individual survey readings, was compiled. For that purpose we selected 'I only wells that had been drilled in California during that year. The footage of Fig. 1 differs from the two earlier tables in that the wells were all drilled in the year 1930. In the earlier tables, the footage shown was surveyed in the years designated, but some of the wells were drilled in earlier years.

Jan 1, 1931

By A. A. Berk

LAGGING technology and the slow spread of information have been the chief obstacles to widespread participation in minimizing the industrial pollution load. These obstacles can be conquered by fact finding and applied research. There are three aspects to the problem of water-borne mineral waste: to minimize the amount being thrown away, to select a predisposal treatment, and to use the products or dispose of them. It is often possible to minimize the waste by making very minor changes in the process that produces it. For example, a manufacturer of automobile bumpers greatly reduced the dragout 'from a plating bath by modifying the design and position of two boltholes.' A plater of automobile hubcaps installed a drainage bar and decreased the loss of chrome-plating solution to the rinse water by about 80 pct.' The mill at a western mine found it possible to discard 60 to 70 pct of an ore with minimum treatment," so that the processing effort could be concentrated on a high-graded slime, with significant reduction in costs and improvement in recovery. The possibilities for waste reduction through process changes are limited only by the imagination. A recent patent points out the advantages of using No. 1 fuel oil instead of water in wet-process cement making;& the fuel oil presumably has better properties than water for this purpose and is said to be almost com'pletely recovered or utilized, so that there is no waterborne waste. Recycling to reduce wastes and improve process economy is very well illustrated in vanadium and uranium recoveries from relatively low grade ore. Ores containing 6 pct calcium carbonate were found to give poor vanadium recovery by the salt-roasting process because the vanadium was converted to water-insoluble calcium vanadate. Following the salt-roasting process, sulfuric acid was used to leach the uranium. Enough calcium sulfate was formed

Jan 1, 1958

By E. A. Breitenbach

A computer program has been developed to afford rapid and complete quantitative log analysis for exploration and production decisions. The computation consists of automatic selection of tops and bottoms of porous intervals from the digitized data, and then point-by-point calculations within each selected interval. Nearly all log types can be analyzed. This paper presents the calculation techniques found to be appticable to machine evaluation and gives examples of their use. INTRODUCTION As the quantitative interpretation of well logs entails repetitive use of charts and equations, it is natural that digital computer programs would be written. A Universal Log Interpretation Computer Program (ULICP) has been developed to afiord rapid and complete analysis for exploration and production decisions. Application of this program enables the log analyst to: (I) apply rapid quantitative log analysis for exploration and production decisions on either a field, a well or on a single zone basis; (2) apply concepts of interpretation requiring detailed numerical analysis; (3) analyze all porous intervals on each log, rather than a few selected zones, and complete the analysis in less time than previously required. Computations are reported for every digitized point in each zone; (4) use empirical techniques applicable to a given area as an integral part of the computation; (5) experiment with the empirical coefficients and exponents in the interpretation equations to find the best possible solution; and (6) automatically plot both the original and computed data to scales analogous to the field prints. The primary utility of a log interpretation program stems from its ability to do an overwhelming amount of work with very little man-power. If a calculation procedure or thought process can be formalized to the extent that step-by-step logic can be written, a computer program can be developed that follows this logic. The major question is one of economics. A feasibility study of the costs for such a program indicates that digital processing is economical primarily as a means of increasing the productivity of the log analyst. In effect, the probability of missing productive intervals in any well, because of a lack of time to do detailed calculations, is greatly reduced. The nucleus of ULICP is programmed to compute large sections of a suite of logs by selecting zones automatically and then performing all pertinent computations on a data point by data point basis within each zone.'.' An entire suite of logs can be processed in this manner with very little manual intervention. Sufficient programming logic is available so that each log analyst can request computations pertinent to his area. These requests are made by simple additions or deletions of information on the input header cards. Hence, the log analyst is always in complete control of the computation process. The evaluation of a suite of logs requires pre-editing, digitization, computation, presentation of results and interpretation. Work by the log analyst is reqilired only in pre-editing and interpretation. Thus, he is allowed more time for comprehensive interpretation, rather than calculation. For continuity, the discussion of ULICP is organized sequentially: pre-editing, digitization, computation and presentation of results. DISCUSSION PRE-EDITING The extent of pre-editing prior to computation is dependent on the format of the original data. For analog prints, it requires inspection, correlation and editing of the logs, plus the entering of required data an special forms. For digitized data such as magnetic tape field recordings, only the special forms are necessary. The process for analog prints will be given here. The inspection and correlation process involves the selection of sections for digitization and the correlation of the traces to a common depth. To decrease the cost of digitization, traces that exhibit large variations in shale formations can be redrawn to a non-zero baseline. The next step is to enter all pertinent data on the input header cards. The header cards presently used for ULICP are presented as Figs. 1 through 6. Cards 1, 2, 3 and 4 (Fig. 1) are defined as the Main Header Cards. They describe the particular well for output identification and give basic information. Cards 5 through 15 (Figs. 2 through 6) are defined as the Block Header Cards. As such, they define the log types and the interpretation parameters for the block of data immediately following. Cards 1 through 10 are required for every computer run. Cards 11 through 14 pertain only to nuclear logs. Card 11 is required if any nuclear log is supplied, and cards 12 through 14 are required only when gamma-ray, density or neutron log data, respectively, are supplied. Card 15 (Fig. 6) must be supplied when cross-plot calculations are required. Either two- or three-component

Jan 1, 1967

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By MERLE HOWARD GUISE

WHEN I was a boy I walked into Fairbanks in 1905. I was but a soft chechako, and arrived with blisters covering my feet, as a result of "mushing" the 400-mile trail on foot. Because of them, the display windows of the trading posts were first to catch my eye-dog and horse collars, harness and sled parts! And because of my enthusiasm for things adventurous, I looked long upon the prospectors' gold pans, shovels, rifles, camp equipment, and what not. Today those windows are filled with motor car accessories, tires and repair parts; yes, even thermos bottles and vacuum cleaners! There were many chance meetings with little parties of prospectors in my youth, and it always set my blood to tingling. Sometimes it was a 70-year-old sun-baked son of the Arizona desert, wrangling his stubborn, faithful jenny away from some outfitting store, at others a shovel-ended poling b0at in northern Canada, \vith the partners and the dogs towing upstream along the bank, or an old sourdough, with tug-rope around neck and hand on the spruce sapling gee-pole, mushing along behind his two or three old, plodding malamutes, dragging a little Yukon sled piled high with rusty sheet-iron stove, pick and shovel, cross-cut saw and axe, rifle, bales of dog salmon, and other paraphernalia. These meetings envisioned the panning of old creek beds and draws in the search for as yet undiscovered pay-channels; they meant the toughest kind of work sinking a hole to bedrock in some far-away valley of promise; they suggested wood fires to thaw the frozen muck and gravel and crude windlass and hand-made tub to hoist the water and the mud; but loudest of all they spoke of Adventure.

Jan 1, 1929

By Carle R. Hayward

ATHOUGH there are signs of improvement in the lead industry, conditions are still far from what we have been accustomed to call normal. There has been little to stim¬ulate research and those responsible for the finances of the companies have been inclined to discourage expenditures except where need was urgent or the prospect for immediate returns bright. In spite of this fact, improvements have been developed here and there which will be available as business conditions become adjusted. No publicity is allowed at present. The rising price of silver has had a tendency to increase the production of lead from argentiferous ores but the greatest interest continues to be in the secondary field. Practically all lead plants situated near large centers of population are treating scrap materials, particularly battery plates, the quantity of which is increasing with the improvement in automobile sales.

Jan 1, 1936

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn's for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962

By M. P. Tixier, A. Poupon, M. E. Loy

Simple qualitative methods are explained for identifying those shaly sands in a well that are most likely to contain oil. A need for more precise measurement of the variables that enter shaly sand analysis is indicated. Field examples are given to illustrate the methods. A theoretical discussion of the quantitative interpretation of shaly sands is given as a basis for discussion and as a guide for the future. While not generally capable of practical application at the present time because of the lack of sufficient accuracy of the electric log data, these methods may become more feasible in the future as the result of the improved logging methods now being introduced. INTRODUCTION Experience has shown that for porous formations containing only a negligible amount of clayey material, reliable information on the fluid saturation and porosity of the reservoir rocks can usually be derived from the electrical logs. The interpretation is based on empirical formulae relating the true resistivity of a porous formation to its lithologic character, to the resistivity of the interstitial water, and to the proportions of water and hydrocarbons in the pores.' If the resistivity of the interstitial water is not known, its approximate value can be derived from the SP curve.2,3 The porosity can usually be determined to a good approximation from a MicroLog, or a MicroLaterolog.4,5 When the reservoir rocks contain an appreciable percentage of clayey material, an additional factor is introduced into the analysis. In a clean formation, the matrix is an electrical insulator, so that the ability of the formation to conduct current is due only to the conductivity of the electrolytes in the pores; in a shaly formation, the shale constitutes a part of the rock matrix able to conduct current, and influences the resistivity of the formation. On the other hand, the spontaneous emf's and the circulation of the SP currents are also responsive to the presence of the shaly material. All other factors being the same, the deflection of the SP curve opposite a shaly permeable formation is smaller than the deflection which would be observed if the formation were clean. The effects of the presence of shale on the resistivity and on the SP curves in a shaly formation are functions of the amount, of the specific resistivity, and of the geometrical distribution of the shaly material within the formation. The presence of shale therefore constitutes an important complication in electrical log interpretation. It is easy to realize, for example, that the presence of a large amount of clayey material in a sand may have such a predominant effect that the resistivity of the sand will not change very much, whether the pores are entirely filled with connate water, or contain a high saturation of hydrocarbons. Important research projects have been undertaken to investigate the influence of shales and to find a way to allow for this influence in the interpretation of a log. The problem of the SP in shaly sands was analyzed mathematically by H. G. Doll"' for the case of sands with shale laminations. Formulae expressing the resistivity of shaly formations were proposed by Patnode and Wyllie8 and de Witte.9 Other quite interesting theoretical and experimental results have been published by various authors.l0,ll,12,l3,14 The purpose of the present paper is to discuss an approach to electrical log interpretation in shaly sands. This approach is based partly on some of the theoretical and experimental data available in the literature and partly on observations made on actual field logs. Comparatively simple methods for qualitative and semi-quantitative analysis are described. These methods depend principally upon information provided by the electrical logs.

Jan 1, 1955

By W. R. Webb, M. O. Peterson

WHEN men drive haulage equipment ranging up to 22 tons in an open pit operation, they must live with the realization that their safety is dependent upon the machines they drive and how well they operate them. The hazards inherent in their jobs must be recognized, met, and defeated. It comprises a never ending struggle toward perfection-an almost un- obtainable goal. The Jones & Laughlin Benson Mines, at Adirondack State Park in New York, created a safety program which resulted in only one three day lost time accident from April 1948 to April 1952. At the very start of the program, management of the open-pit operation recognized the hazards existing at Benson. The program was designed to meet each danger. With a knowledge of the problem faced, the process of minimizing each facet was planned along lines of maintenance of equipment and training of personnel. Its success is evident. In the ever-present struggle, care and maintenance of machines and application of experience to new equipment design are mainstays. Truck Haulage Benson produced 2.9 million tons of crude iron ore and 1.6 million tons of waste in 1951. To do the job, truck mileage reached 500,000 miles. The tremendous mileage emphasized to safety planners, the fact that the more work done, the greater the possibility of risk in haulage operations. Instrumenting the aim of the safest equipment possible is a methodical servicing program. Like other segments of the drive, the servicing program is based on greater production with fewer accidents. Every truck is serviced at least once per eight-hr shift. Examination includes inspecting and tightening wheel studs, checking tires, steering apparatus, lights, brakes, wipers, heaters, fire extinguishers, and refueling. A running history of the equipment's operating life is kept in the form of service and maintenance records. Machine operators are constantly on the alert for malfunctioning of units. At the first sign of trouble the truck is returned to the garage for exchange. No truck functioning incorrectly is kept on the line, regardless of its shift check schedule. The program resulted in a reduction of the number of costly overhauls and cut down the number of haulage accidents. Miscellaneous Mobile Equipment Auxiliary units, operating within the pit, have presented definite safety problems. The highest accident rate in the pit occurred on trucks carrying water and bits to the churn mills. The weight and awkwardness of bits and drill stems, combined with remote delivery points were direct causes of numerous accidents. Here, the problem has been one of equipment handling, rather than haulage. All air compressors for secondary drilling are truck mounted, facilitating mobility. In addition to making it easier to move the equipment, truck mounting has eliminated many of the hazards connected with relocating machinery. By making air compressors independent of other units, drilling operations have been speeded up considerably. Unseen rocks in the path of moving vehicles are a constant source of tire damage. At Benson the problem has been met by supplying each loading crew with a bulldozer for cleanup operations. The pitman directs the dozer operation, and when truck drivers back into loading areas, he serves as an extra set of eyes. Modern Truck Garage Provides Drive-Through Service Simplicity is the essence of any preventative maintenance program. At Benson, a modern garage, with a drive-through service bay simplifies servicing. Shift inspection of the 22-ton haulage units is accomplished with minimum delay and maximum thoroughness. Major repair work and periodic overhauls are done in the repair section of the truck garage. Crane facilities for handling heavy assemblies ease the job and add to the safety factor. Other mobile machinery,

Jan 1, 1952

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.' Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

By AIME AIME

INSTITUTE members attending the Annual Meeting in New York who want to see one of the mining engineers' newest aids, photoelastic stress analysis, are due for an interesting afternoon on Thursday, Feb. 15, when open house: will be held at the Columbia University mining laboratory. Information as to the direction and distribution off stresses in mine structures, which has been developed by Professor Bucky, associate professor at the Columbia School of Mines, and David Sinclair, research assistant, is useful in the design of pillars and in the placing of openings relative to working places such as gangways and haulage levels.: This work has been sponsored during the last ten years by the Engineering Foundation.. It is fully reported in T. P. No. 1140.

Jan 1, 1940

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962