Search Documents

By Robert Ammon

THE purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator, at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 nun. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5-mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0mm. 9. Remarks on the inner feel cone. In the following pages all overflows, are given in quartz dimensions; i.e., by a 0.75-mm. overflow 'is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm.

Jan 8, 1913

By A. R. Troiano, W. J. Barnett

The existence of a grain size stabilization effect on martensitic type reactions as shown by Scheill in an iron-29 pct nickel alloy and by Troiano and Tokich2 in cobalt prompted a review of other martensitic reactions to determine if this stabilization effect is characteristic of all martensite type reactions. Preliminary work has shown this effect to be present both in the gamma —+ epsilon transformation in an iron-20 pct manganese alloy and the martensite transformation of SAE 4140 and 3 pct Cr-O.40 pct steels. No appreciable effect was found in an SAE 2340 steel. The M, temperature for the gamma —+ epsilon transformation was lowered from 380°F to about room temperature by varying the annealing treatment following cold work as shown in Table I. The effect of austenitic grain size on the M, of three steels is shown in Table 2. M, was deter- mined by the conventional quench-temper method of Greninger and Troiano. In a single crystal the change in external shape concomitant with the homogeneous shear mechanism of the martensite transformation can take place unhindered. In a polycrystalline specimen a restraint of these changes must occur at the grain boundaries. Therefore, the smaller the grain size the greater the shear strain energy necessary for the formation of a martensite crystal. The degree of lowering of M, due to the reduction of grain size is much greater when the change in crystal structure involves only a small energy change, such as face-centered cubic —+ close packed hexagonal (that is, CO and Fe-20 pct manganese alloy). The maximum lowering of M, observed in the steels investigated was 50°F with a change in the ASTM austenitic grain size of 1-2 to 8-9. In comparison, the crystal structure change face-centered cubic —+ body-centered tetragonal involves a considerable energy change. There is little doubt that with much finer grain sizes the increased grain boundary restraint would greatly enhance this stabilization effect. The implications of this phenomenon are multifold. Undoubtedly. under certain conditions it offers a method of stabilizing high temperature phases for room temperature

Jan 1, 1949

INTRODUCTION It has been impossible for the student, the practicing engineer, and the geologist to find all of the essential elements of mineral appraisal and mineral economic analysis in a single text. Indeed, the most recent texts on mine evaluation are over 20 years old. Many of the basic principles of mine sampling and evaluation have not changed over the ensuing years, but with the advent of the digital computer the entire scope of mineral evaluation has been expanded to encompass superior techniques that heretofore were not possible when using manual methods. The old manual methods for ore reserve computations and the techniques for assignment of area of influence to drill-hole samples are now as antiquated as the Model-T Ford. With the computer making possible solutions that had not been practicable in terms of time and effort, it is important for the practicing explorationist and mining engineer to understand many of the new concepts and principles that can be applied with the resolving power of the computer. Many practicing mineral industry professionals have been disappointed by certain computer programs and thus have some reservations about computers being able to solve their very real problems. Often the gap between the practicing engineer and the ivory tower theoretician applying modern computer techniques is too broad to be bridged with scattered, fragmented publications. PURPOSE AND SCOPE OF TEXT It is the intent of this book to update and to unify a great many scattered reference works used in the mineral industry today. The ensuing pages are addressed both to the professional already working in the mineral industry who needs information on computerized methods as well as to the serious student seeking to grasp the fundamentals and modern techniques of mineral appraisal and feasibility. These techniques are based on sound mathematical principles and theory, with the computer as a tool-but a very essential tool-for the solution of the problems involved. The computer can be of value only if it is programmed by those having sufficient expertise to use its inherent problem-solving capability, and the output is interpreted by those who are sufficiently acquainted with its operation to understand the data it produces. In the pages that follow the author intends to outline in considerable detail all the essen-

Jan 1, 1980

By W. S. Steele

Vermiculite is a nonmetallic mineral of the mica family, probably related to biotite mica. Its occurrence has been noted at numerous places in the United States and in some foreign countries, but it can be said that vermiculite is of only moderately wide distribution. A laboratory and field survey of over 60 deposits in the United States by F. 1;. Schundler & Co., of Joliet, Ill., indicates that the purest deposit represented in this survey is on the property of the Zonolite Company at Libby, Montana The Zonolite Company is commercially active and the vermiculite it produces is sold as Zonolite. Hereafter, in this report, the word "Zonolite " will be used to designate the vermiculite produced by the Zonolite Company. Values given herein to Zonolite are peculiar to the vermiculite produced from the Zonolite Company's deposits. References to " vermicullite," are to he interpreted as covering the broad field covered by the Schundler survey. Composition and Characteristics of Vermiculite Vermiculite is an aluminum-nmgnesium silicate. The following typical analysis is published by the United States Bureau of Standards: silica, 41 per cent; iron oxide, 7; aluminum oxide, 18; magnesium oxide, 21; calcium oxide, 1; alkalis (sodium and potassium), 1; moisture, 11. Vermiculite breaks down into platelike formation in crushing and grinding operations. Its cleavage is basal. Crude, screened, dry Zonolit,e weighs between 80 and 90 Ib. per cubic foot; its specific gravity is 2.8 and its specific heat is approximately 2. The fusion point of Zonolit'e is 2462" F. Crude vermiculite contains between 7 and 9 per cent of chemically combined moisture. The instantaneous introduction of crude Zonolite into an expansion furnace at a temperature of between 1800" and 2000" F. transforms the combined moisture into steam, which in an effort to liberate itself forces all explosive expansion of the platelike crude material

Jan 1, 1934

By James A. Clem

Approximately 2000 years ago, the Lord admonished the scribes (lawyers) and pharisees (religious leaders of that time) that they had paid the tithe but had omitted the weightier matters of law, judgment, mercy, and faith. (Matt. 23:23) I want to talk about "The Weightier Matters of Law." In a situation where big government is trying to have an effect on even small details of a work activity, otherwise simple situations become complex. Regulations are written to such detail that constant compliance with strict interpretations can be a nightmare-not to mention off the target of the intended purpose for the regulation. One soon recognizes the onerous characteristics of federal statutes. Another admonition the Lord gave those lawyers and pharisees back then was that they tended to strain at a gnat and swallow a camel! He meant that the pharisees were given to devoting themselves to the strict interpretation of law by writing hundreds of subrules or interpretation to law. In doing so they eventually lost sight of the original purpose of the law. I think they were being told, keep the law-but don't neglect to humanize it Keep it simple Recognize the purpose of why the law. "Mix in" a common sense approach. Someone once said, "Common sense is instinct -enough of it is genius." Today, as 2000 years ago, we need more "genius" displayed by legislators in considering the weightier matters of law. First of all true legislature genius calls for a declarative statement about the purpose of the statute and a fair, objective analysis of the ground rules by which it will be implemented. In the Health & Safety Act of 1969, the "findings and purpose" as set forth in Section 2 do define its purpose. I believe most of us affected can be in accord with the reasons advanced for the legislation. However, beyond those well-intentioned few paragraphs, we very quickly run into trouble. Congress complicated the simplicity of the statement of purpose by mandating government intervention into areas that cannot be effectively legislated, nor even should be legislated. The Act provided for broad gaged regulation which is unnecessary, inappropriate, and tremendously costly. Frankly, it detracts from a constructive, cooperative effort by the parties involved. These are strong negatives which characterize inappropriate legislation. Appropriate legislation and subsequent regulation, which is realistically conceived and practically enforced must be born of an honest desire for improvement, based on a working knowledge of common problems which are thoughtfully analyzed. Then the legislation must be written in clear concise language so that there can be little or no doubt as to its literal meaning and intent. To be practically enforced, it must be understood by all who will enforce it and by all who are subject to it. That is to say, an effective law or standard cannot be fixed or inflexible so that it cannot be tempered in human judgment. There must be an elasticity in the statute to provide for consideration of all of the relevant facts of a given situation. Such elasticity makes the compliance effort as meaningful as it can be for the time and dollars invested. Meaningful compliance requires room for common sense. Today, we in business along with our associates in government and labor, urgently need to pause, and assess our current situation. The problems arising from the 1969 Act have been intensified through the Mine Safety & Health Act of 1977. After reading the "findings and purpose" of this legislation, and by process of elimination, we should all clearly see what is and is not the purpose of the Act. 1) It is not to turn the management of private industry over to government. 2) It is not to impair the efficient operation of business. 3) It is not to reduce productivity and profits. 4) It is not to reduce national unemployment. 5) It is not to perpetuate the bureaucracy. 6) It is not to increase the tax burden on an already overburdened people. 7) It is not to increase our balance of payments deficit. 9) It is not to replace management/labor relations in working together to solve problems.

Jan 1, 1981

By L. F. Mondolfo, B. E. Sundquist

The undercooling associated with the nucleation of the secondary phase from the liquid by the solid primary phase was studied in sixty binary alloys by means of a hot-stage microscope. It was found that in a system of a and ß, a usually nucleates ß at low undercoolings, but ß does not nucleate a, except possibly at undercoolings approaching homogeneous nucleation. This behavior can be explained in terms of relative interfacial energies and shows that crystallographic disregistry is only a minor factor in heterogeneous nucleation from metallic liquids. PREVIOUS experimental work1-6 on nucleation of solids from liquids has shown that normally nucleation is heterogeneous, and that small solid particles present in the liquid are responsible for the nucleation. These experiments and the theory that has evolved from them have made apparent that there is a "characteristic undercooling" associated with the nucleation of the solid from a given liquid by a given impurity. Little is known, however, about the chemical and structural relationships between the nucleating agent and nucleated solid that control the effectiveness of the nucleating agent in catalyzing the nucleation, as measured by the required undercooling. A review of the literature has yielded seventeen undercoolingsL-6 for the nucleation of solid from liquid metals by "known" nucleating agents. All values come from experiments in which the metal studied was divided into a number of particles (10 to 300 pin diam.) much larger than the number of extraneous impurity particles so as to obtain a large number of particles free of foreign nucleating catalysts. Known nucleating agents are then introduced by coating the droplets with particles or a thin film of the catalyst. Six of the seventeen undercooling values referred to cases where, for various reasons, the identity of the nucleating species was not at all certain. Another six cases involved nucleating agents with a crystal structure that was not known. Four other cases involved undercoolings listed as greater than or equal to undercoolings which were very likely those for homogeneous nucleation. One investigation3 involved adding to droplets powdered oxides, carbides, and so forth that were doubtlessly covered with adsorbed oxide or nitride films. The highly variable nature of these films resulted in highly variable undercooling (as was also found in preliminary work in this investigation). It is apparent that the information on heterogeneous nucleation in liquid metals is too limited to give rise to any definite conclusions on the nature of the catalytic process. With these problems in mind a new method was

Jan 1, 1962

By A. H. Redfield

BITUMENS have been defined by Abraham1 as substances of variable color, hardness, and volatility; composed principally of 'saturated hydrocarbons, substantially free from oxygenated bodies, sometimes associated with mineral matter; the nonmineral constituents being fusible and largely soluble in carbon disulphide. The principal bituminous substances other than petroleums known to commerce are: (1) native asphaltites, such as gilsonite, grahamite, and glance pitch, distinguished by their hardness and relatively high fusing point; (2) native asphaltic pyrobitumens, such as wurtzilite, distinguished by their infusibility and comparative insolubility in carbon disulphide; (3) mineral waxes, such as ozokerite, distinguished by their high content of crystallizable paraffins; (4) native asphalts, containing varying amouqts of mineral matter, distinguished by the comparative absence of crystallizable paraffins; and (5) bituminous residues obtained from the distillation of petroleum. GILSONITE Gilsonite, a black native asphaltite 98 to 99.9 pct pure, characterized by a hardness of 2 (Mohs), a specific gravity of 1.01 to 1.10, and melting point of 230° to 400°F (K and S), is mined commercially only in northeastern Utah. It occurs in parallel, almost vertical veins, from a few inches to 18 ft wide and 8 to 30 miles long, that cut across the Tertiary limestone and shale of the broad Uinta Basin. The bitumen is believed to have been distilled by heat from oily material in the underlying Green River shale. At the Rainbow mine of the American Gilsonite CO.,† the gilsonite, formerly extracted in an opencut by a system of slopes and benches, is now mined by shafts and horizontal drifts. Little timbering is required. The mining methods of the Raven Mining Co., Chicago, and of the American Asphalt Association and the Utah Gilsonite Co., both of

Jan 1, 1949

By Nathaniel Arbiter, Norman L. Weiss

Factors now accelerating the trend to larger concentrators and larger equipment units are reviewed. After almost 40 years of stability with unit sizes less than 100 cu ft, 200 and 300-cu-ft flotation-cell units are now operating and a 500-cu-ft machine is being built. The design of these cells is considered, as is the design and operation of flotation circuits against the background of the need to achieve greater process efficiency while holding down operating and investment costs. Particular attention is paid to the scale-up problem. With the newer cells having five to ten times higher unit capacities, the advantages resulting from this in sampling, mill operation nnd control, testing and plant layout are indicated, as well as the broad direction for changes in the overall design of 50,000 to 100,000-tpd concentrators. A comparison is given of the available larger cells of U.S. manufacture with analysis of differences and similarities. After almost 60 years of application in this country, froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups, the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign, the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency. and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum—to mention only the most important metals occurring in the U.S. as sulfides- must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000-tpd milling rate on copper ores. Table 1' shows the trend in copper ore grades in U.S. in recent years. Table 2' shows the projected annual growth rate of consumption 1966-1985. A study by one of the authors 25 years ago showed that of 32 copper mills in North America with more than 100-tpd capacity, only eight had capacities exceeding 10,000 tpd. The average for these eight was 25,000 tpd. These included the three giants of that day, Magna, Arthur, and Morenci; the other five averaged a little over 10,000 tpd. Today instead of the eight mills with capacities exceeding 10,000-tpd capacity we have 25, and the mill with less than 1000-tpd capacity is fast becoming extinct. Much less range is found in lead and zinc mills, which are still generally small except for the few with over 1000-tpd capacity in Missouri, Utah, and Idaho, and a few zinc ore mills in the same size category. Molybdenum and potash operations are the fastest growers in North America today, but when one considers the projected increase in consumption of copper together with the projected decrease in grade of ore (3% annually), he can foresee that copper ore milling will soon lead the list. Technological improvements to meet the challenge of lower-grade ores have taken the wholly predictable path toward bigger equipment. In mining, shovels, draglines, scrapers, and trucks have led the way; in ore processing, we have seen a rapid increase in size of grinding mills, flotation cells, and pumps. Twenty-five years ago, for example, the 10-ft-diam ball mills treating 2000 tpd at Morenci were considered the giants, but today some grinding mills in similar service have five times that capacity. The specific matters to be dealt with in this paper are 1) the underlying principles that affect flotation-machine design, and the conditions required to produce

Jan 1, 1971

By L. F. Bryant, J. P. Hirth, R. Speiser

The surface, gain boundary, and twin boundary energies, as well as the surface diffusion coefficient, of cobalt were determined from tests at 1354°C in pure hydrogen. A value of 1970 ergs per sq cm was calculated for the surface energy, using the zero creep method. It was possible to measure the creep strains at room temperature because the phase transformation was accompanied by negligible irreversible strain and no kinking. Established techniques based on interference microscopy were used to obtain values for the other three properties. The gain boundary and twin boundary energies were 650 ad 12.7 ergs per sq cm, respectively, while a value of 2.75 x l0 sq cm per sec was determined for the surface dufusion coefficient. In the course of a general study of cobalt and cobalt-base alloys, information was required about the surface energy of cobalt. Hence, the present program was undertaken to measure the interfacial free energy, or, briefly, the surface energy, of the solid-vapor interface of cobalt. The microcreep method was selected for this measurement because other surface properties could also be determined from the accompanying thermal grooving at grain boundaries and twin boundaries. A brief summary of the methods for determining the various surface properties follows. At very high temperatures and under applied stresses too small to initiate slip, small-diameter wires will change in length by the process of diffu-sional creep described by Herring.1 The wires acquire the familiar bamboo structure and increase or decrease in length in direct proportion to the net force on the specimen. For a specimen experiencing a zero creep rate, the applied load, wo, necessary to offset the effects of the surface energy, y,, and grain boundary energy, y b, is given by the relation: where r is the wire radius and n is the number of grains per unit length of wire. The first results obtained from wire specimens were reported by Udin, Shaler, and Wulff.' udin3 later corrected these results for the effect of grain boundary energy. The grain boundary energy is determined from measurements of the dihedral angle 8 of the groove which develops by thermal etching at the grain boundary-free surface junction. For an equilibrium configuration: Measurements of the angle 8 can be made on the creep specimens4'5 or on sheet material, as was done in this investigation by a method employing interference microscopy.= If the vapor pressure is low, the rate at which grain boundary grooves widen is determined primarily by surface diffusion and, to a lesser extent, by bulk diffusion. The surface diffusion coefficient, D,, is obtained from interferometric measurements of the groove width as a function of the annealing time, t. As predicted by Mullins~ and verified by experiment, the distance, w,, between the maxima of the humps formed on either side of the grain boundary increases in proportion to if grooving proceeds by surface diffusion alone. For this case: where fl is the atomic volume and n is the number of atoms per square centimeter of surface. When volume diffusion also contributes to the widening, the surface diffusion contribution can be extracted from the data by the method described by Mullins and shewmon.8 Where a pair of twin boundaries intersects a free surface, a groove with an included angle of A + B (using the groove figure and notations of Robertson and shewmong) forms by thermal etching at one twin boundary-free surface junction. If the "torque terms", i.e., the terms in the Herring10 equations describing the orientation dependence of the surface energy, are sufficiently large, an "inverted groove" with an included angle of 360 deg-A'-B' develops at the other intersection. The angles A + B and A' + B' are measured interferometrically. When the angle, , between the twinning plane and the macroscopic surface plane is near 90 deg, the twin boundary energy is calculated from the relation: 1) EXPERIMENTAL TECHNIQUES Five-mil-diam wire containing 56 parts per million impurities was used for making ten creep specimens. These specimens had about 15 mm gage lengths with appended loops of wire and carried loads (the specimen weight below the midpoint of the gage length) ranging from 3.7 to 149.8 mg. The wires were hung inside a can made from 99.6 pct pure cobalt sheet. Beneath the wires were placed small specimens of 20-mil-thick, 99.9982 pct pure cobalt sheet from which the relative twin boundary and grain boundary energies and the surface diffusion coefficient were measured. All the specimens were annealed at a temperature of 1354" i 3°C which is 92 pct of the absolute melting point of cobalt. The furnace atmosphere was 99.9 pct pure hydrogen that was purified further by a Deoxo catalytic unit, magnesium perchlorate, and a liquid-nitrogen cold trap. As a precautionary measure the gas was then passed through titanium alloy turnings which were heated to 280" to 420°C and replaced after every test period. The hydrogen was maintained at a

Jan 1, 1969

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By Joel H. Watkins

The terms kaolin, china clay, ball clay, and paper clay are more or less loosely and interchangeably applied to a large class of white-burning clays. These clays are made up chiefly of hydrous amorphous (colloidal) aluminum silicates with variable amounts of free silica and other impurities in small quantities. Occasionally also the term kaolinite is wrongly applied to a white-burning clay, for kaolinite is a mineral of definite chemical composition and definite crystalline form which occurs but sparingly in nature. It is not the purpose of this paper, however, to define or classify clays, or to enter into a discussion of the chemistry of clays. It is rather a general description of the occurrence and methods of mining of a kindred group of clays, and a discussion of their future economic aspect. In the Southern Appalachian States, the mining of white-burning clays has in recent years become an important industry. Although these clays are of several distinct types, which occur in as many localities under different geologic conditions, they are for the most part primarily of the same origin. They are essentially the same in elementary constituents, and are largely consumed in the game industrial arts. From the standpoint of a mining engineer, therefore, and for convenience in comparison and correlation, it should be interesting to discuss them under one heading. Kinds of Clay The most important types of clay which are now being actively mined in the Southern Appalachian States and with which this paper is particularly concerned are the North Carolina, Virginia, and Georgia kaolins or china clays (residual); the South Carolina and Georgia kaolins or paper clays (sedimentary); and the Florida and Tennessee plastic kaolins or ball clays (sedimentary). Other varieties which are interesting but which are as yet of little importance are the pocket deposits of white clay in Augusta County, Virginia, the bauxitic kaolins of Tennessee,

Jan 1, 1915

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.' The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.' The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

By Warren H. Westphal

For mining and exploration, and indeed the entire mineral industry, the first century of AIME has ended with far more problems than it began. Paradoxically, most of these problems have arisen not because, the industry has been unsuccessful, but rather because it has succeeded too well. Whatever the public demand for minerals over the past 100 years, it has somehow been met-and met at a price well within the public's ability to pay for the products. But as AIME moves into its second century, the past successes of mining and exploration are beginning to levy a tax on the future. Prospectors have already found most of the rich and ready ores, and miners have dug them out. New mineral assets grow progressively harder to come by, and as they do, the need for them grows inversely more pressing. How and where and at what cost can adequate supplies be found? How and at what cost can they be mined from heretofore inaccessible recesses deep underground and under the seas-or from vast surface tonnages containing only minor values? And once they are found or won, how can these assets be husbanded for generations to come? How also can they be extracted without injury to the land, air and water on which we and our successors must depend? And what constructive use can be made of the incidental materials now treated merely as wastes-sometimes at great expense?

Jan 1, 1971

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.1 This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material in. which the crystals here dealt with were grown was made from 1/8-in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, ass nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. MEASUREMENTS The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, ?, from one direction of the wire axis, and an azimuth or longitude, [ø], from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most. of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

Jan 1, 1928

By W. H. Brandt

THERE has been much progress in the last two decades in understanding the hardenability of steel. Roughly, the progress has been along two lines, which may be designated as empirical and fundamental. This empirical work has progressed to the point where steels may be manufactured to the desired characteristics quite closely and heat-treatment and application problems can be approached with considerable confidence. Particularly noteworthy among the empirical work is that of Grossmann,12 who has given formulas for calculating hardenability as a function of composition, and the establishment of the isothermal transformation curve by Davenport and Bain.13 The latter does not fall entirely in the class of an empirical study, for while it provides a means of presenting a tremendous amount of empirical data in the form of a single curve, it also outlines clearly the problems that face the fundamental investigator. The isothermal transformation curve shows clearly that the phenomena occurring in the neighborhood of the knee of the curve are those that limit the hardenability of steel. Above the knee of the curve, the product of decomposition of austenite is lamellar pearlite and fundamental progress has consisted chiefly of a detailed study of structure and formation of pearlite, largely at the hands of Mehl and his collaborators.1-5 They have shown that formation of pearlite proceeds by a process of nucleation and growth and they measured both the nucleation and growth rate. However, there is still a wide gap between our empirical knowledge and fundamental knowledge, owing largely to the fact that there is no satisfactory theory of nucleation rate or of growth rate. This paper is being written in an attempt to fill in a small part of the gap. A method was presented recently14 for calculating the velocity of edgewise growth of pearlite using an expression for the carbon concentration that satisfies the diffusion equation. The edgewise velocity of pearlite growth in a plain carbon eutectoid steel was calculated, using linear extrapolations of the ferrite and cementite solubilities. While the results are in fairly good agreement with the experimental facts, the calculated velocity of edgewise growth is smaller at 600°C. than G, the radial growth velocity of pearlite nodules, whereas one would expect it to be larger. In this paper the calculation will be repeated using a new extrapolation for the ferrite solubility, which gives better agreement between G and V, the calculated velocity of edgewise growth. A calculation will also be made of the effect of carbon content on velocity of edgewise growth, and the problems of calculating the effects of other alloying elements on growth rates will be discussed. It will be assumed that the mechanism of pearlite growth, established by Mehl and

Jan 1, 1945

By Juanito C. Fernandez

INTRODUCTION The Philippines is endowed with mineral resources, much of which still remains unexploited. The country's known reserves, at least for the major mineral commodities, have increased every decade since the first major discoveries more than 80 years ago. Mining, therefore, naturally evolved as one of the pioneer industries and has ever since been a major factor in economic development. The Philippines has entered a new era in mineral resources development and management. One significant feature of this era is the degree to which the government is involved with the industry. In recent years, the state has increasingly encouraged the private sector to carry out detailed exploration aided by governmental contributions through extensive geological and geophysical surveys, fundamental researches and even indirect financial assistance in some specific areas. Significant changes in mineral resources development policies were brought about with the promulgation of Presidential Decree 463 or the Mineral Resources Development Decree of 1974. The Decree provides for a more rational system of administration and disposition of mineral lands to promote mineral resource exploration and exploitation. Various forms of incentives are provided. Foreign entities are allowed to participate in development through service contracts with leaseholders or with the government in the case of reserved areas. The thrust in mineral resources development has been focused on the base metals which as envisioned would provide the foundation for sound economic development. In recent years, however, major strides have been made to promote the exploitation of the non-traditionally produced commodities especially the non-metals. Development likewise point to the growing determination of the government and the private sector to expand benefits from mining. This is evident in efforts to promote downstream processing operations and to encourage investments in exploration, exploitation and mineral processing ventures. The integrated mineral resources development plan, therefore, proposes the vertical integration of mining extraction activities with the processing requirements of the metal-based manufacturing industries. While mining activities shall continue to be carved out by the private sector, the government shall influence the industry's direction by establishing legitimate goals to maximize benefits through an integrated approach giving due consideration to environmental protection and resource needs of future generations. STATUS OF MINERAL RESOURCES DEVELOPMENT Extent of Exploration Application of modem exploration tools and concepts complemented by intense infusion of foreign technology and rapid development of indigenous expertise have enabled the government jointly with the private sector to geologically explore vast grounds and to expand the country's known mineral resources. Approximately 93% of the country's total land area of 30 million hectares have been geologically mapped on at least 1:250,000 scale. Of the 93% total coverage, roughly 37.54% or 11.07 million hectares have been done on scales of 1:10,000 to 1:50,000 as shown in Figure I. Only 3.07% of the total coverage have been surveyed in detail. Land gravity surveys have been undertaken on over 45% of the total, while some 77,300 line km. of aeromagnetic surveys have been flown over 110,000 sq. km. of land area. Processing of data is almost complete. Total magnetic intensity and IGRF-corrected maps are available. Geological interpretation utilizing Landsat MSS imagery and low altitude aerial photography augmented by ground truthing have been undertaken in several large areas with very encouraging results. Beach and offshore mineral surveys were initiated in 1977 and have covered substantial areas in northwest and southeast Luzon and northeastern Mindanao. Highly promising areas for detrital magnetite, chromite, gold and some heavy minerals including ilmenite and titanium have been identified. In the petroleum sector, two offshore oilfields are currently producing from Miocene limestone reefs in Northwestern Palawan. Another field from the same area will be on stream in mid-1982.

Jan 1, 1982

By T. A. Lang

For permanent structure underground, where rock is not competent, support usually consists of concrete or reinforced concrete. However, temporary supports in the form of timber or steel are often needed during construc-tion. Although the history of rock bolting is relatively short—50 years— their use has become widespread in general engineering construction as well as mining. This profusely illustrated and detailed study covers a broad range in the field of rock belting: from the behavior of rock and bolts including rock properties, masses, and structure; mathematical formulae for rock bolt applications; through analysis of various operations and descriptions of the bolts themselves. Rock construction is one of the oldest of the engineering arts and its origin is lost in antiquity. From the days when early man decided that he wanted to improve the natural caves which he was using for shelter and protection or made a river crossing by placing rocks to form a ford or causeway, we have had structures made of rock. It is not too much to say that rock in situ as a structural material forms part of every major engineering undertaking. Rock bolting is one means whereby the inherently good characteristics of rock in situ are preserved and used to the best advantage and the bad characteristics ameliorated. In many cases the latter are accentuated by construction processes used. Rock bolting, as with other rock construction techniques, is only just beginning to emerge from being an art. Consequently, its theory and practice is still more descriptive than mathematical. ROCK BOLTING In underground excavations, where the rock is not competent, support is provided. For the permanent structure, this generally consists of concrete or reinforced concrete. However, support may be needed during construction before the concrete can be placed, and conventionally this consists of timber or steel support in the form of ribs, struts, and lagging. Alternatively, rock bolts may be used. Although their use dates back over 50 years, it is only in recent years that rock bolts have become widely used, not only in mining but in general engineering construction. A rock bolt is a steel bar which is inserted in a hole drilled in rock. The end away from the rock face has a device which permits it to be firmly an- chored in the hole and the projecting end is fitted with a plate which bears against the rock surface. The bolt is placed in tension between the anchor and the plate, thereby exerting a compressive force on the rock. The essential feature of a rock bolt is that it is placed in tension. This distinguishes it from anchor bars which are grouted into holes in rock, but which are not prestressed. The difference between an anchor bar and a rock bolt when the rock bolt is grouted in is analogous to the difference between the reinforcement in ordinary reinforced concrete and in prestressed reinforced concrete. The view that rock bolts only pin or nail blocks or slabs of rock which are loose to the sounder rock behind them is erroneous. Rock bolts are useful for this purpose and have been so used for a long time. However, the term rock bolting, as used here, means the designed use of rock bolts to reinforce and develop the rock around an excavation into a structural entity which can competently play its part in a structure such as a powerhouse or a mine installation. Rock bolts behave quite differently than steel ribs. They can be installed at the working face directly after blasting and within a short space of time can be exerting a stabilizing pressure on the loosened rock surface. This early installation not only partially restores loosened blocks of rock to their original unloosened positions, but also it prevents the gradual relaxation or loosening of the decompression zone behind the new rock face. In contrast, steel ribs generally use timber blocks, wedges, and lagging between the ribs and the irregular rock surface. The timber is relatively compressible, and loosened blocks of rock must move outwards an appreciable distance before any load builds up on the steel ribs. Also, the ribs may settle as the foot blocks and foundation become compressed. Hence, it may take several days or weeks before the rock has moved sufficiently to make the steel ribs carry an effective load.

Jan 1, 1961

By T. Egleston

The manufacture of charcoal in kilns was declared many years ago, after a series of experiments made in poorly constructed furnaces, to be unprofitable, and the subject is dismissed by most writers with the remark that in order to use the method economically the products of distillation, both liquid and gaseous, must be collected. It is asserted with truth that the number of kilns required for a large production of iron would be so great that it is doubtful whether any works would be justified in making the necessary outlay for their constructiou, but it can also be asserted with equal truth that for any such production in a given locality the use of charcoal as fuel would be eqnally unjustifiable. It appears to have been forgotten that there were other manufactures besides iron in which large amounts of charcoal were used, but these consumers seen] to have been guided entirely by the results of the experiments of the iron men, who necessarily made the largest qnantity of it. Some authors speak in a doubtful way of the quality of the charcoal produced, and a few concede that with great care good charcoal can he made in kilns, but that most of the workmen do not like kiln 'charcoal. This is the real secret of the opposition to this method of manufacture. Most of these objections were written when charcoal was the most important fuel used by the iron manufacturer, and when what was a largeproduction of iron for several furnaces was less than that produced by a single modern one, in localities where other fuels can be had. Almost all that has been written on the subject related to the use of the fuel for the manufacture of iron in the blast furnace, where very peculiar properties are required, and where the qnantity produced is limited by the height of the furnace, and this in turn by the crushing resistance of the charcoal. A large production was, therefore, only possible when the best and hardest woods were used. Of all these objections there is not a single one which is not eqnally applicable to any method of charcoal manufacture, whether it be meilers, pits, or furnaces. Until recently, therefore, the manufacturers of charcoal iron

Jan 1, 1880

By R. E. H. Pomeroy

The statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Mc Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. % in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5" B., flashing in open test at 199" F. The oil is heated to about 200" F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 Ib. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-08. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and " dog houses" to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent. The draft at the firing end of the furnace is 0.18 in. of water. At the throat or in the uptake above the "verb" the draft is about 1 in.

Jan 1, 1915

By Oliver Bowles

Two striking events marked the year 1871-the establishment of the A.I.M.E. and the beginning of the portland cement industry, the most spectacular of all the nonmetallics in its development. Just as David Saylor's first portland cement, made in a little mill at Allentown, Pa., in that year was the forerunner of a mighty industry, the products of which in 1942 were made in 155 plants scattered throughout the country (having attained a value of nearly $300,000,000), so the Institute from its small beginning has attained a membership of many thousands, likewise decentralized into a series of individual sections of wide geographical distribution. Concurrent with the establishment of the Institute was also the invention of the steam drill, followed by the compressed-air drill about 1904. These mechanical drills were so immeasurably in advance of the hand drill and hammer used previously that quarrying and mining of present-day magnitude could never have been attained without them. Some outstanding occurrences have marked this eventful three quarters of a century. The concrete age, with its enormous demands for cement, aggregates and steel, is of primary importance. Of interest also is the shift of fertilizers from the organic to the mineral field. Nitrates, primarily obtained

Jan 1, 1947