Search Documents

By S. A. Spachner

An analysis of the powder patterns of the omega transition phase in three binary titanium alloys containing 8 pct Cr, 13 pet Mo, and 15 pet V, respectively, showed that all could be indexed on an orthorhombic unit cell. The unit-cell dimensions were all quite similar. There is evidence for the occurrence of more than one transition phase in Ti-Cr and Ti-V alloys. FOLLOWING the discovery of a new brittle phase in certain titanium-chromium alloys by Frost, Parris, Hirsch, Doig, and Schwartz,' named ? by these investigators, much interest has developed concerning the identification of alloy systems in which this phase exists, kinetics of the transformation in such systems, and the crystal structure of the ? phases appearing. Omega has been found in alloys of titanium-manganese, titanium-molybdenum, titanium-iron,' and titanium-vanadium.' In the present work, a study was made of the powder patterns of the ? phase occurring in alloys of Ti-8Cr, Ti-13Mo and Ti-15V in an effort to obtain a basis of comparison for ? phases appearing in these different alloys. Comparison of Alloys for ?-Phases Two hundred mesh powders of Ti-8Cr, Ti-13Mo and Ti-15V were prepared. A portion of powder sufficient for three x-ray powder specimens was placed in a Vycor tube, evacuated to less than 0.1 µ pressure, filled with argon, and sealed. The tubes were then heated to 900°C, held at this temperature for 30 min, and water-quenched. Following this transformation to the ß phase, the specimens were quenched in lead or solder pots, held at the desired temperature for varying lengths of time and water-quenched. The heat-treatments used and the phases identified are listed in Table I. The intermediate water quench was used in lieu of direct downquenching from 900°C to the bath temperature desired to circumvent the possibility of transformation of the powder specimen from ß to (ß + a) while it was being moved from the homog-enization furnace to the lead bath. To check the possibility that upquenching to the bath temperature might bring into play a different mechanism than downquenching to this temperature, resistivity measurements were compared on Ti-8Cr rod specimens which were transformed isothermally at 400°C by downquenching from the solution-treatment temperature and those which were transformed at 400" C by upquenching ß specimens from room temperature. The results are shown in Fig. 1. No difference in transformation mechanism was noted. It soon became apparent that sufficiently detailed Debye-Scherrer photograms of the ? phase in the alloys which were to be used could not be obtained by the use of copper radiation. Although satisfactory photograms of ß and ß + a phases were obtained with this radiation, the ? phase appeared to exhibit mild fluorescence, making interplanar spacing computation virtually impossible. Molybdenum radiation appeared to offer promise in cutting down this fluorescent effect, the mass absorption of titanium for molybdenum radiation being 23.7 in contrast to 204 for copper radiation. The reduction in the accuracy in determining the location of the photo-gram lines caused by the shorter wave length of molybdenum characteristic radiation did not appear to be a significant factor. Utilizing a camera of 57.3 mm radius, best results were obtained for exposure times ranging between 30 and 40 hr. Tube potential

Jan 1, 1959

Abbott, Argyle Campbell 1209 Sherwin Ave, Chicago, ILL. '29 Almstrom, Adne A., Student, Met. Engrg, Washington State College Pullman, Wash. '29 Ankedinoff, N., School of Mines, Univ. of Utah Salt Lake City, Utah. '30 Apter, Robert F., Student, McGill Univ Montreal, Que., Canada. '30 Bailey, Donald G 798 1/2 Kensington Rd., Los Angeles, Cal. '29 Baker, Kenneth B., Met, Aluminum Co. of America Pittsburgh, Pa. '29 Barger, Thomas, Student, Univ of North Dakota Grand Forks, N D '23 Bartholomees, Geo. C Box 304, Bonne Terre, Mo. '29 Bates, Walter, Student, Univ. of Utah, School of Mines . Salt Lake City, Utah '30 Bobb. Russell V. . 16 College Ave., Houghton, Mich. '29 Boswell, John C., Stripping Asst, Fairbanks Exploration Co Fairbanks, Alaska '29 Brandenburg, E. C., Student, Univ of Kentucky 112 Church St, Lexington, Ky '29 Brannen, John, Chemist, Assay Office, Consolidated Min & Smelt Co. of Canada, Ltd , Tadanac, B. C , Canada '29

Jan 1, 1923

By R. G. Schaal

The Magma Mine at Superior, Arizona had an unimpressive beginning as a. worked out silver mine that was purchased in 1910 for $130,000 and then incorporated into the Magma Copper Company which has been continuously mining the deposit since 1915. Copper is the principal metal produced. However, zinc, gold, silver and iron have also contributed to the total metal product. Prior to 1973, the production rate of 1500 tons per day was maintained by hoisting 4 and 5 ton pay-loads at speeds up to 1100 FPM through four small hoisting shafts. The hoists used included 8' and 7' diameter double drum, double clutched doc. and a.c. motor driven geared units built as early as 1917. One old timer that did yoeman's service for many years was an 8' Bollen Pulley with a.c. geared drive that utilized an endless rope system with mechanical grip and release mechanism built into the pulley's throat. Primary power for all of these old production hoists was 25 Hertz. Exploration that was completed in 1967 developed a reserve of 10 Million tons of 5 per cent copper which was sufficient to justify new capital expenditures for enlargement of productive facilities to 3300 tons per day. To reach the new reserves a 22' I.D. concrete lined vertical shaft was sunk to an initial depth of 48431. A 12 ½ diameter adit was bored from the mill side of the mountain to intercept the shaft at a point about 1100' below the collar. This 9200' long adit provides the right-of-way for the mine to mill railway and egress for heavy supplies from rail head as well as a conduit for potable water, electric power, compressed air and mine drainage. Mine operating levels begin 3582' below collar and thereafter have been cut at 100' vertical intervals. Skip loading stations have been installed 4282' and 46821 below collar with an in-shaft skip dump station located 800' below collar. This provides for 4500 tons of storage above the mine to mill train loading station located 1100' below collar. Ore and waste are moved horizontally from stope chutes and drift headings by rail haulage to transfer raises which channel all material to the two mentioned skip loading stations. The 22' diameter shaft crossection is arranged with the two skip compartments on the south side separated from the manway and utility compartments by the cage compartment. The cage counterweight operates in a portion of the southwest quadrant of the shaft. The hoisting plant consists of two conventional Nordberg double drum, single clutch, geared, d.c. motor driven units that are identical except for the drives and automatic controls. The drums are 15' diameter x 105" face with LeBus grooving for 2-1/8" diameter wire rope wound in three layers. Mechanical design emp1o::ed is the same as has been used for the past twenty- five years. One drum is attached to the main shaft by 2 large bolted integral shaft flenge. The loose drum is engaged by a 4-arm positive tooth clutch meshing with radially cut teeth of the clutch ring which is bolted to the drum. The drums are one-piece steel plate weldments having a finished weight of 60 tons each and are mounted upon a 36" diameter shaft that also weighs 60 tons. With the addition of brake rings, clutch, bull gear and rope, the total dead weight adds up to nearly 250 tons that is supported by just three double row spherical roller pillow block bearings. There is no bearing between the drums. All pinion shafts as veil as all head sheave journals are supported in the same type of antifriction bearings.

Jan 1, 1975

By J. H. Swisher, E. O. Fuchs

Rate equations were derived to describe the kinetics of internal oxidation of cylinders and spheres. The derived equations for cylinders were checked experimentally by means of sub scale thickness and electrical conductivity measurements on Cu-Cr alloy wires. The properties of the internally oxidized samples were examined with conductivity applications in mind. It was possible to produce uniform dispersions of Cr2O3 in copper with an initial chromium content as high as 3 wt pct. While electrical conductivities only a few pct less than that of OFHC copper were obtained, the Cr2Os particle size and spacing were too large for effective dispersion hardening. T.HE process of internal oxidation has been used widely in basic studies of the permeability of gases in metals. In a review article, Rapp1 has discussed the principles of internal oxidation in considerable detail. From a technological standpoint, internal oxidation is often considered undesirable, since it is a means by which inclusions can be introduced into an otherwise clean material. Another important aspect of internal oxidation is its use as a means of dispersion hardening a material. Broutman and Krock2 discuss this and other methods for making dispersion hardened alloys. The only internally oxidized material known to the authors which is commercially available is a Cu-BeO alloy.3'4 This alloy is made from Cu-Be alloy powder, using a so-called Rhines pack. It has a tensile strength of 80,000 psi and retains its strength at relatively high temperatures. The objectives of the present study were to derive rate equations for the internal oxidation of cylinders and spheres, to check the derived equations for cylinders experimentally, and to examine the structure and properties of internally oxidized Cu-Cr alloys. The Cu-Cr system was chosen for this study because uniform dispersions are obtainable at high alloy contents, which is a desirable characteristic in dispersion hardened materials. RATE EQUATIONS FOR VARIOUS GEOMETRIES A number of authors5--9 have derived equations to describe internal oxidation kinetics. These derivations differ somewhat in mathematical assumptions and approximations, and all except one of the derivations deal exclusively with the internal oxidation of plates. The exception is a brief treatment of cylindrical and spherical geometries given by Meijering and Druy-vesteyn9 as a part of a comprehensive paper on the general subject of internal oxidation. These authors did not obtain rate data to check their derivations, although they did show that the hardness profile across an internally oxidized sample is directly related to the rate of interface movement. For cylindrical and spherical geometries, a quasi-steady-state approximation is needed to circumvent mathematical complications in obtaining a solution to the basic differential equations. In using this approximation, we consider the concentration gradient of dissolved oxygen in the internally oxidized zone or sub-scale to be the same as the gradient which would be present if there were no movement of the subscale interface. The steady-state approximation introduces an error of about 1 pct in computing the rate of internal oxidation of an Fe-1.0 pct Mn alloy plate, if the present method is compared to the more exact method of Wagner.7'10 The details of the derivations of the rate equations for cylinders and spheres are given in the Appendix, and only the results of these derivations are given below. The final equations obtained by Meijering and Druyvesteyn9 can be shown to be equivalent to our Eqs. [1] and [2], although the two approaches are somewhat different. Cylindrical Geometry. [2] where r1 is the outer radius of the cylinder or sphere, cm, r2 is the radius of the unreacted core, cm, see Fig. l(a), D is the diffusion coefficient of oxygen in copper, cm2 per sec, %O is the concentration of dissolved oxygen at the surface of the specimen, wt pct, %Cr is the initial chromium concentration in the alloy, wt pct, and t is the reaction time, sec. Plate Geometry. The analogous rate equation for a plate has been derived previously for internal oxidation of Fe-Al alloys.8'11 For Cu-Cr alloys, we may write the same equation as follows: [3] where r1 is the half-thickness of the plate, cm, and r2 is the distance from the mid-plane to the subscale intherate is An analysis of Eqs. [1], [2], and [3] shows that for a plate the rate is completely parabolic. The initial

Jan 1, 1970

By J. C. Allen, E. V. Herring

CHILE EXPLORATION CO's. oxide plant at Chuquicamata, the largest of its kind, started in 1915 with initial operations at the rate of 10,000 tons of ore per day. Anaconda Copper Mining Co. acquired the controlling interest in 1923 and in the next few years modernized the plant and mine, extending operations to a nominal capacity of 490 million lb of electrolytic copper yearly by 1942. Plant production averaging 495.7 million lb of copper per year was maintained for the eight-year period extending from 1941 to 1948 inclusive. During the World War II production reached its highest level when in 1944 the output was 531.8 million lb. The maximum production for any one month was 49.6 million lb, achieved in May 1947. E. A. Cappelen Smith, consulting metallurgist for M. Guggenheim's Sons, worked out the first process for the treatment of Chuquicamata copper oxide ore about 1913, and directed a staff of 20 young engineers operating a pilot plant at Perth Amboy, N. J., on three shifts for an entire year. The copper is extracted from the oxide ore by a hydro-metallurgical treatment described in detail by T. A. Campbell in AIME Transactions, Vol. 106, Copper Metallurgy, 1933. The Oxide Plant is divided into five main operations as follows: (1) Crushing, (2) Leaching, including dechloridizing and sulphur dioxide treatment, (3) Tailing disposal, (4) Electrolytic precipitation, (5) Smelting and melting. Crushing The present Primary Crushing Plant has been in operation 25 years, during which time 4,342,112 cars of 70 tons net capacity have passed through the dumpers. The ore as received from the mine is frequently blocky and up to 5 feet in section. It is reduced to 9-in. size by two 60-in. gyratory crushers, and transported to the east and west ore bins by 60-in. conveyors. In the secondary crushing operation the ore is first reduced to 2 to 3-in. size by five standard 7-ft cone crushers and two No. 10 gyratories. This product is then reduced to 3/8-in. size by fifty-two 48-in. vertical Symons disc crushers and is transported by belt conveyors to the loading bridges from which it is charged° into the leaching vats. Conveyor belt No. 14 which serves the eight vats in the east section of the leaching plant has transported over 125 million tons of ore, which is a record for any type of conveyor. This 60-in. belt travels at a speed of 600 fpm and carries loads up to 5500 tons per hr. Leaching The ore is leached in 14 vats, averaging 13,500 short tons net capacity each. These vats are lined with a natural mastic which adequately resists the sulphuric acid leaching solutions. The leaching process as presently conducted comprises soaking the ore with successive volumes of leaching solution and spent electrolyte and withdrawing successive volumes of enriched solution from the vat to a total of approximately 3.2 million gal. The first 1.6 million gal of this volume withdrawn is called strong solution and contains about 35 parts of copper per 1000. The balance of 1.6 million gal subsequently withdrawn is stored in a

Jan 1, 1952

By M. T. Hepworth, A. K. Stewart

Iron containing 0.1 pct A1 and -0.9 pct P by weight was internally oxidized in the temperature range 900° to 1300° C, where the bcc structure is stabilized by phosphorous. By measuring the depth of penetration of oxygen with time in an internally oxidized zone for an imposed surface oxygen potential, oxygen permeability was determined. The dgfusion coefficient of oxygen in iron was then calculated using known solubility data, yielding the expression: where Do is the diffusion coefficient of oxygen in bcc iron in sq cm per sec and T is temperature in OK. RECENTLY Hepworth, Smith, and Turkdoganl measured the diffusivity of oxygen in bcc iron and reported the temperature dependence of diffusivity from data determined in the a, and 6 temperature ranges. Subsequently Swisher and Turkdogan' have measured the diffusivity of oxygen in fcc iron. Internal oxidation techniques were employed by these investigators and in this current study. The analysis of this technique is developed by wagner3 (presented in English by Hauffe4 and Rapp 5). In this present study bcc iron stabilized by phosphorous was used to determine oxygen diffusivity in the temperature range 900° to 1300°C. Meijerin 6 has studied oxygen permeability in this temperature range using bcc iron stabilized with 5 pct Sn. Other inves- tigators who have studied oxygen permeability in bcc iron at other temperatures are Schenck et al., 7 Bohen-kamp and Engell, 8 and Bradford. EXPERIMENTAL Electrolytic iron of 99.99 pct purity was alloyed to contain 0.897 pct P and 0.093 pct Al. The maximum weight percent phosphorous required to stabilize bcc iron between 910" and 1392°C is 0.51 pct as determined by Haughton,10 0.42 pct by Roquet and jegaden," and 0.58 pct by vogel,12 with the latter value preferred by Hansen.13 Microprobe analysis indicated that there was no segregation of the phosphorous either before or after permeability studies; therefore, the quantity of phosphorous added was assumed to be sufficient to stabilize the bcc structure. Furthermore, the permeability results of studies on this alloy agreed substantially with interpolated values from previous data on bcc iron.' An ingot of the Fe-P-A1 alloy was hot-rolled to a l-in.-thick slab. Specimens were machined to dimensions: 13/8 by $ by 1/4 in. The experimental apparatus and procedure used have been described before.' A constant oxygen potential was established by passing argon and hydrogen through a column of oxalic acid dihydrate, which has a water vapor pressure which is well-known as a function of temperature. Slab specimens were exposed to a gas mixture sufficiently lean in oxygen to prevent the formation of a surface oxide for predetermined temperature for selected times. The specimens were then quenched, sectioned, and examined metallo-graphically. All quenched specimens were iron-plated to provide protection from the outside sample edge during polishing. Fig. 1 shows a typical microstruc-ture for a specimen oxidized at 953°C for 48.00 hr at a water vapor-to-hydrogen pressure ratio of 0.20. DISCUSSION AND RESULTS The following equation was derived by Hepworth et al.' from Wagner's kinetic expressions for internal oxidation:

Jan 1, 1969

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine miles across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker's observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40° to 45° southeast.

Jan 1, 1873

By J. A. Heskett

NEW ZEALAND is dependent on the outside world for its ferro goods, yet it can boast of at least two well-defined iron-ore deposits; namely, Para Para limonite, 3 Fe203 + 21120 also found as lower hydrated oxides, and Taranaki iron-sand, a combined magnetite and ilmenite, 2FeO + 2Fe203 + FeO + Ti02. The former is of massive variety and the FIG. 1.-VIEW OF WORKS SHOWING IRON-SAND DEPOSITS, ALSO WHARF AND BREAK¬WATER IN THE DISTANCE. latter granular and mixed with various proportions of fine shell and siliceous sand well water-worn. This latter deposit forms the greater portion of the beach sands of the west coast of the North Island of New Zealand. It is so fine that the whole of a sample passed through a sieve of 40 meshes to the inch. The ilmenite cannot be detected by the microscope, as in the titaniferous ores of the Adirondacks, nor can it be magnetically separated, as in the titaniferous ore of Natashkwan, Canada. To all appearances it is a chemical compound of the double oxides of iron and titanium and not a mechanical mixture, as is the ore of the Adirondack deposits.

Jan 8, 1920

By AIME AIME

THE autumn is the time that nearly all the special groups within the broad field of the Institute's activitives chose for their own special meetings. The big annual meeting in New York in February has its own special advantages, but to realize them involves sacrificing others. A meeting of a smaller group with the subjects brought up for discussion much more closely limited to a single field of interest has some advantages that a big general meeting cannot possibly have. And so the custom has gradually developed of having these smaller meetings in the autumn, at con¬venient places, so the men will not have to travel too far from the job to be present. Sometimes the meetings have for their field of interest a single phase of mineral technology, and are called divisional, and at other times they cover a diversity of topics that are locally important in that geographical area, and are then called regional meetings. Of the five meetings to be held this fall, four are divisional and one regional. Two of the divisional meetings are to be held in the same place at the same time, but with programs so arranged that they do not conflict.

Jan 1, 1930

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine milt",3 across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker's observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40' to 45' southeast

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

KNOWLEDGE of the isothermal transformation behavior and the TTT chart method of graphically summarizing such information has been of invaluable aid to the ferrous metallurgist in understanding and developing heat treatments intended to provide specific mechanical properties. It is to be expected that similar lines of study directed to titanium-base alloys will be as profitable. This paper summarizes, on conventional TTT charts, the isothermal transformation products and pertinent reaction rate data for binary alloys of titanium containing 1, 3, 5, 7, 9, and 11 pct Mo, respectively. The results so presented were derived from metal-lographic examination. Some X-ray diffraction work was done to clarify certain points of question. Ti-Mo System To the authors' k.nowledge, TTT charts have only been used to describe the reaction rates of eutectoidal decompositions. It would seem that the kinetics of decomposition of any unstable solid solution might be conveniently described in this manner. The equilibrium diagram of the Ti-Mo system' is shown in Fig. 1. The similarity with the Fe-Ni system will be recognized. Additions of molybdenum serve to stabilize the /3 phase to increasingly lower temperatures. The solubility of molybdenum in the a phase is restricted to less than 1 pct at 600°C. Under normal conditions. a homogeneous ,8 structure quenched to a, temperature in the a f & field will reject a of invariant composition. The rate at which this occurs depends on the degree of undercooling and the degree of supersaturation of /3. The structural character of the rejected phase may also be expected to be related to the undercooling. Materials and Experimental Methods A sponge titanium was used which has a nominal impurity content as reported in Table I. The nominal composition of the molybdenum used is also included. The alloys were prepared in 150 g melts by arc melting in an evacuated water-cooled copper crucible of the type reported in an earlier paper.' The pancake-type ingots were forged to 1/4x1/4 in. bars and homogenized for 24 hr at 1000°C in evacuated Vycor bulbs. Specimens Vi in. thick were cut from these bars for heat treatment. The heat treatment cycles followed an invariant procedure. The specimens were soaked at 1000°C for 20 min under a helium protective atmosphere prior to quenching into a lead bath held at a temperature corresponding to a chosen degree of undercooling. After a prescribed period of time at this temperature, the specimen was removed and water quenched. A series of specimens so treated for progressively longer periods served to establish the times for initiation and completion of the decomposition of the /3 phase at a particular temperature. Although heat treatment of unprotected specimens in a lead bath does permit surface contamination by lead diffusion, this method is necessary to insure sufficiently rapid quenching rates. As long as the bath treatments were of less than 1 hr duration. the contaminated surface was not unduly deep and could be removed without excessive grinding. Metal-lographically, the contaminated zone could be readily distinguished from the pure binary alloy. Transformation Characteristics of Ti-Mo Alloys Metallographic examination showed that a supersaturated p phase may decompose by one of two processes. Alloys containing 1 to 9 pct Mo, when quenched in water from the homogeneous /3 field,

Jan 1, 1953

By H. R. Banks

The Sullivan concentrator has completed 20 years of operation. During this period a considerable amount of data has been accumulated concerning the characteristics of several types of flotation machines in their application to the problem of the differential separation of the lead sulphide, zinc sulphide and, in more recent times, iron sulphide, in the ore from the Sullivan mine. It is the author's intention to sketch briefly experiences encountered when the several types of flotation machines were introduced into the flow. Original Flotation Equipment and Ore The original flotation equipment consisted of four 18-cell lead-roughing machines, whose concentrate was cleaned in an 8-cell and recleaned in a similar 8-cell machine. Zinc concentration was carried out in four 18-cell machines. One 8-cell zinc re-treatment machine received the reground zinc middling. The 168 cells handled some 3000 tons of original daily feed. These cells were of the standard Minerals Separation type, equipped with 24-in. impellers. Spindles were driven through geared line shaft at a speed of 255 r.P.m. The impellers were the 45' type, except for the last three cells of the zinc-rougher machines, which were of sub-aeration type, with full bottom shroud and half shroud for the top side of the impellers. Four-pound air was introduced. This recognition of the benefit of intensified flotation operation for "gleaning" was an important phase in the early operation and will be discussed further on in this paper. Sullivan ore during this period is described as a finely disseminated mixture of four sulphides, totaling go per cent made up of 13.6 per cent galena, 14.4 per cent mar-matite, I per cent pyrite and 61 per cent pyrrhotite. The specific gravity of the ore was approximately 4.4. There has been a gradual change in the ore content. The 10 per cent of nonsulphide constituents has increased to between IS and 20 per cent and all three sulphides have dropped somewhat. Added equipment and changing technique have made possible the treatment of 8000 tons per day of mill feed instead of the 3000 originally handled. Special Features of Flotation at Sullivan Sullivan flotation differs greatly from customary practice. The very heavy return of lead rougher middling and lead cleaner tailing, totaling at times 125 per cent of the new feed tonnage, has been the subject of much investigation. The practice is still employed. This operating condition is mentioned because it is the author's belief that the in-

Jan 1, 1947

By H. R. Banks

The Sullivan concentrator has completed 20 years of operation. During this period a considerable amount of data has been accumulated concerning the characteristics of several types of flotation machines in their application to the problem of the differential separation of the lead sulphide, zinc sulphide and, in more recent times, iron sulphide, in the ore from the Sullivan mine. It is the author's intention to sketch briefly experiences encountered when the several types of flotation machines were introduced into the flow. Original Flotation Equipment and Ore The original flotation equipment consisted of four 18-cell lead-roughing machines, whose concentrate was cleaned in an 8-cell and recleaned in a similar 8-cell machine. Zinc concentration was carried out in four 18-cell machines. One 8-cell zinc re-treatment machine received the reground zinc middling. The 168 cells handled some 3000 tons of original daily feed. These cells were of the standard Minerals Separation type, equipped with 24-in. impellers. Spindles were driven through geared line shaft at a speed of 255 r.P.m. The impellers were the 45' type, except for the last three cells of the zinc-rougher machines, which were of sub-aeration type, with full bottom shroud and half shroud for the top side of the impellers. Four-pound air was introduced. This recognition of the benefit of intensified flotation operation for "gleaning" was an important phase in the early operation and will be discussed further on in this paper. Sullivan ore during this period is described as a finely disseminated mixture of four sulphides, totaling go per cent made up of 13.6 per cent galena, 14.4 per cent mar-matite, I per cent pyrite and 61 per cent pyrrhotite. The specific gravity of the ore was approximately 4.4. There has been a gradual change in the ore content. The 10 per cent of nonsulphide constituents has increased to between IS and 20 per cent and all three sulphides have dropped somewhat. Added equipment and changing technique have made possible the treatment of 8000 tons per day of mill feed instead of the 3000 originally handled. Special Features of Flotation at Sullivan Sullivan flotation differs greatly from customary practice. The very heavy return of lead rougher middling and lead cleaner tailing, totaling at times 125 per cent of the new feed tonnage, has been the subject of much investigation. The practice is still employed. This operating condition is mentioned because it is the author's belief that the in-

Jan 1, 1947

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By J. Brian Eby

The Gulf Coast area of Louisiana enjoyed a particularly active and profitable year in 1939. Fifteen new producing structures were located and approximately sixty new producing sand horizons in old fields were opened in that period of time. The most important new discoveries are the Eola field, Avoyelles Parish, and the Paradis, St. Charles Parish. The Eola strike was indicated during December 1938, but the well was not placed on production until January 1939. Eola is particularly important because it was the first discovery of oil in a commercial quantity in the Wilcox formation in that area. Sid Richardson, of Ft. Worth, Texas, drilled the first well on the Haas Investment Company's property, which encountered the producing sand at a little below 8500 ft. Within the year 48 wells were drilled, 42 being commercial producers and 6 dry holes. The second most favorable discovery was the Paradis field, which was discovered by The Texas Company's Louisiana Land and Exploration Company's Paradis No. 1 well, in St. Charles Parish, just west of New Orleans. Detailed information concerning this field has not yet been made available but it is reported that the oil sand is as much as 175 ft. thick. The initial production indicated was 1750 bbl. daily and reports suggest a very large structure. In Calcasieu Parish the Humble Oil and Refining Company's Edge-wood Land No. 1 discovered gas in the Oligocene at a total depth of 7042 ft., in the Perkins area. Although two additional dry holes have been drilled in this prospect, it is still believed to have some merit. A new discovery is credited to Cameron Parish with the finding of Miocene oil in the Superior Oil Company's State No. 1 well in Grand Lake. The Chalkley field, Cameron Parish, is credited as a 1938 discovery but was largely developed in 1939 into one of the more important new fields. During the year 13 wells were drilled, 8 being oil wells and 5 dry holes. The oil is found in the Oligocene at depths of approximately 9000 feet.

Jan 1, 1940

By J. Brian Eby

The Gulf Coast area of Louisiana enjoyed a particularly active and profitable year in 1939. Fifteen new producing structures were located and approximately sixty new producing sand horizons in old fields were opened in that period of time. The most important new discoveries are the Eola field, Avoyelles Parish, and the Paradis, St. Charles Parish. The Eola strike was indicated during December 1938, but the well was not placed on production until January 1939. Eola is particularly important because it was the first discovery of oil in a commercial quantity in the Wilcox formation in that area. Sid Richardson, of Ft. Worth, Texas, drilled the first well on the Haas Investment Company's property, which encountered the producing sand at a little below 8500 ft. Within the year 48 wells were drilled, 42 being commercial producers and 6 dry holes. The second most favorable discovery was the Paradis field, which was discovered by The Texas Company's Louisiana Land and Exploration Company's Paradis No. 1 well, in St. Charles Parish, just west of New Orleans. Detailed information concerning this field has not yet been made available but it is reported that the oil sand is as much as 175 ft. thick. The initial production indicated was 1750 bbl. daily and reports suggest a very large structure. In Calcasieu Parish the Humble Oil and Refining Company's Edge-wood Land No. 1 discovered gas in the Oligocene at a total depth of 7042 ft., in the Perkins area. Although two additional dry holes have been drilled in this prospect, it is still believed to have some merit. A new discovery is credited to Cameron Parish with the finding of Miocene oil in the Superior Oil Company's State No. 1 well in Grand Lake. The Chalkley field, Cameron Parish, is credited as a 1938 discovery but was largely developed in 1939 into one of the more important new fields. During the year 13 wells were drilled, 8 being oil wells and 5 dry holes. The oil is found in the Oligocene at depths of approximately 9000 feet.

Jan 1, 1940

By N. E. Norman, R. Stier

The mining industry is continually seeking out new and better underground mining techniques. One of the most recent-also, perhaps, the most significant-of the new concepts in underground mining is the use of mechanical rock-boring machines. And one of the problems that concerns us all in this matter is the cost of mechanical rock tunneling. To help answer the oft-quoted question "What will it cost me?" the following pages deal with the operating costs of so-called "medium to medium hard rock" boring machines-i.e., those designed to meet the drilling requirements in 8000 psi to 25,000 psi rock. A few machines are capable of drilling hard rock above 25,000 psi, but the economics of mechanical tunneling in rock that hard is limited at the present time. [ ] For mechanical rock tunneling, there are five main cost factors influencing the expense: Capital Investment, Cutters, Labor, Power Requirements, and Maintenance. These factors give us a good basic picture of the cost of excavation, although muck handling, erecting supports, and other costs directly related to conventional tunneling and mechanical boring enter into the final picture.

Jan 6, 1967

By N. A. Zeigler

GRaphitization phenomena occurring in solid cast iron have principally been studied from the angle of the reactions taking place during annealing of white castings in the manufacturing of malleable iron. The selected bibliography at the end of this paper presents the high spots of the published information in this field. Graph-itization of gray iron upon reheating has received much less attention, primarily because only on rare occasions is this material subjected to any kind of industrial heat-treating. Moreovcr, articles made from gray iron are seldom used commercially at temperatures when any graphitization can take place. When used in such conditions, it is assumed that the articles can be replaced at frequent intervals, which can be afforded because of the low cost of gray iron. However, there is at least one commercial process in which articles made from gray iron, during their manufacturing processing, are subjectcd to rather high temperatures; that is, manufacturing of cast-iron enamelware, which is glazed at about 1600° to 1700°F. (870' to 930°C.) From practical experience, it has been found that one of the convenient and economical compositions of gray iron suitable for enameling is, in round figures, as follows: Si, 2.50 per cent; Mn, 0.35; S, 0.07; P, 0.80; T.C., 3.35; C.C., 0.70. Since this iron usually is cast into thin-walled sections, the percentage of com- bined carbon in it is relatively high. Upon heating in the enameling furnaces, this combined carbon graphitizes, which causes permanent dimensional changes of the articles. Obviously, from practical considerations, it is desirable to maintain these dimensional changes as constant as possible. In the course of experimentation with this iron, two series of experimental heats were prepared in which the manganese to sulphur ratio of the standard cupola metal was offset by ladle additions of: (I) progressively larger amounts of sulphur, and (2) progressively larger amounts of manganese. Each one of these ladle charges was cast into experimental plates 8 by 4 in. and about 5/16 in. thick. All told, 13 ladle charges were thus treated. All of them are listed in Table I, together with their chemical analyses. It may be noted that the manganese to sulphur ratio in these samples ranges between 1.2 and 30.2. Every one of these compositions was subjected to thermal allalysis, using an automatic, self-recording differential dila-tometer. The specimens used in this instrument are 50 mm. long and 4 mm. in diameter. During the dilatometer cycle they are kept under a vacuum of about 3 microns. Each one of them was subjected to a thermal cycle by heating it to I830°F. (1000°C.) in 3 hr. and cooling to room temperaturc in 5 hr. Figs. I, 2 and 3 present three automatically recorded dilatometer curves for irons: Serial No. I (normal composition), Serial No. 6 (high sulphur), and Serial No. 13 (high manganese). All three of these figures are

Jan 1, 1945

By E. H. Edwards, J. Washburn, E. R. Parker

The mechanism of strain hardening was discussed in connection with some recent observations on the stress-induced motion of dislocation boundaries and on the simple shear deformation of zinc, cadmium, and copper crystals. THE nature of work hardening accompanying plastic deformation of metals has long been the subject of speculation. As early as 1925, Becker' suggested a thermodynamic process to explain slip based on the statistical probability for the occurrence of local glide steps. The theory that plastic glide was due to the presence of lattice defects known as dislocations was first introduced in 1934 by Taylor: and Orowan, and Polanyi.4 Taylor presented a rather complete analysis of the behavior and interaction of dislocations. He assumed a certain type of stress field to be associated with a single dislocation, and postulated that work hardening would result from plastic flow in two ways. First, dislocations following one another across a slip plane might encounter a barrier which would impede their movement, thereby gradually diminishing and eventually stopping plastic flow on that plane. The second mechanism involved the concept of dislocations traveling in opposite directions on nearby planes attracting one another to form a meta-stable lattice. The interaction of dislocations in such an array was shown to be large enough to require an increase in stress before plastic flow would continue. Kochendorfer5,6 extended the concept of work hardening involving a back stress due to an accumulation of like dislocations on a slip plane. He suggested that the formation of a new dislocation is hindered by those dislocations already present. The hardening resulting from the interaction of newly forming dislocations with bound dislocations was designated as "formative hardening," and indicated to be the only type of hardening necessarily connected with the slip process. In another detailed picture of work hardening, Mott and Nabarro7 assumed that sufficient dislocations are primarily present in the crystal as a consequence of growth irregularities (mosaic structure) to initiate slip. Work hardening resulted from the interaction of migrating dislocations with localized internal stresses produced during deformation. More recently, however, Mott8 as modified his treatment to include the generation of dislocations at Frank-Read sources and he accounts for the hardening by the formation of sessile dislocations. It has been widely accepted that metals of hexagonal structure, usually possessing only one set of glide planes, exhibit mechanical behavior markedly different from those having cubic structures. However, the differences in behavior of the two classes may be less fundamental than suggested. Rohm and Kochendorfer9 have shown that a single crystal of aluminum subjected to approximately simple shear gives the type of stress-strain curve associated with the hexagonal metals. Similar behavior has been demonstrated for gold and silver crystals by Andrade and Henderson.'" Thus when glide in cubic metals is restricted to one plane, the strain hardening characteristics closely resemble those of the hexagonal metals. It would appear, therefore, that an investigation of some of the strain hardening properties of single crystals sheared in simple glide might provide a more complete understanding of the phenomenon of work hardening. This report relates a number of recent observations made on single crystals of copper, zinc, and cadmium tested in simple shear. In addition, pertinent observations of effects accompanying stress-induced movement of dislocation boundaries are reported. Experimental Procedure and Results Details of the production and advantages of the type of single-crystal shear specimen employed for the following tests have been presented in a previous publication.n The method of testing makes

Jan 1, 1954