Search Documents

By FRANK RIEBERS

IN DISCUSSING the selection of a geophysical method, much of what the writer will say is applicable to any of the various methods and to their use in prospecting, whether for oil or for other minerals. Specifically, the writer's subject is the problem, particularly pressing on the Pacific Coast, of checking the rising cost of the discovery of new fields by the proper employment of geophysical methods. Table I was prepared from statistics published by the California State Milling Bureau. The writer selected five of the largest a:ld most active companies operating in California, segregated the number of wild-

Jan 1, 1930

By Persifor Frazer

The following notes on the Whopper and adjoining mines in the Gunnison district of Colorado mere made in the spring of this year. The time chosen for the author to visit the region was, unfortunately, the most unfavorable of an exceptionably unfavorable year. About the middle of May all the hill slopes, which at this period of the pear are generally covered with pasture, were thickly covered with snow. The unusually large precipitation of this Tear caused loacal mountain torrents at every few hundred feet, which wore away the oft foothills into gulches, gouged great chasms out of the roads, and transformed miles of usually dry soil into dangerous quagmires. Travel was totally interrupted for weeks, except on horseback or afoot, and even then with great difficulty and some danger. The Whopper mine is situated on the Whopper Mountain, about two miles from the headwaters of Rock Creek, and on the right hank of that stream. The Whopper Creek flows into Rock Creek horn the east, and, by a precipitous descent, offers excellent facilities for its utilization as a source of power. This stream, which pours past the picturesque Whopper Cabin about thirty tons of water a minute, has a fall of 100 feet in 400 yards, and is said to be a stream of some size, even at the seasons of the year when drought prevails. The Whopper claim extends down the hill a distance of about 250 feet to its intersection with the Whopper Creek (on the other side of which is a small tunnel on its extension called the "Teller") and over the steep hill northwest to the limits of the claim about 1250 feet. The part of the mountain in which this mine is situated is remarkable for its splendid forest, the spruce, fir, and quaking asp covering the mountain-sides with a green growth of valuable timber. The distance from Gothic City to this mine is about eight miles along the valleys of East River and Rock Creek, and on the divide which separates them. The elevation of Gothic City is given from the engineer's notes as 9500 feet above sea-level, and the mean of several observations with a Beck watch-barometer made the elevation of Whopper Cabin (which is about fifteen feet above the floor of the Whopper upper tunnel) about 1260 feet above Skiles's Cabin in Gothic City. The record of this instrument must, how-

Jan 1, 1881

By Persifor Frazer

THE following notes on the Whopper and adjoining mines in the Gunnison district of Colorado were made in the spring of this year. The time chosen for the author to visit the region was, unfortunately, the most unfavorable of an exceptionably unfavorable year. About the middle of May all the hill slopes, which at this period of the year are generally covered with pasture, were thickly covered with snow. The unusually large precipitation of this year caused local mountain torrents at every few hundred feet, which wore away the soft foothills into gulches, gouged great chasms out of the roads, and transformed miles of usually dry soil into dangerous quagmires. Travel was totally interrupted for weeks, except on horseback or afoot, and even then with great difficulty and some danger. The Whopper mine is situated on the Whopper Mountain, about two miles from the headwaters of Rock Creek, and on the right bank of that stream. The Whopper Creek flows into Rock Creek from the east, and, by a precipitous descent, offers excellent facilities for its utilization as a source of power. This stream, which pours past the picturesque Whopper Cabin .about thirty tons of water a minute, has a fall of 100 feet in 400 yards, and is said to be a stream of some size, even at the seasons of the year when-drought prevails. The Whopper claim extends down the bill a distance of about 250 feet to its intersection with the Whopper Creek (on the other side of which is a small tunnel on its extension called the "Teller ") and over the steep hill northwest to the limits of the claim about 1250 feet. The part of the mountain in which this mine is situated is remarkable for its splendid forest, the spruce, fir, and quaking asp covering the mountain-sides with a green growth of valuable timber. The distance from Gothic City to this mine is about eight miles along the valleys of East River and Rock Creek, and on the divide which separates them. The elevation of Gothic City is given from the engineer's notes as 9500 feet above sea-level, and the mean of several observations with a Beck watch-barometer made the elevation of Whopper Cabin (which is about fifteen feet above the floor of the Whopper upper tunnel) about 1250 feet above Skiles's Cabin in Gothic City. The record of this instrument must, how-

Jan 1, 1881

By M. G. Corson

THE theory of hardening by interference with slip which has been so clearly developed by Jeffries and his co-workers requires that an alloy to be amenable to age or heat hardening should contain among its components some that will stay in solid solution at high temperatures and precipitate as a secondary phase on cooling. This secondary phase may be either a more or less pure individual element (chromium in the case of copper, anti-mony in the case of lead), or some intermetallic com-pound. Those cases of hardening which depend on the precipitation of a compound are not only the most frequent, but are also far superior in the efficiency of hardening obtained. However, the slip interference theory as stated in its most general form is not sufficient to foretell new cases of this type of hardening and also will not explain some phenomena of a more intricate nature. It is not sufficient that a secondary phase might be absorbed by the main one at high temperatures and precipitated at the lower ones. The kinetics of this precipitation and the accompanying. physical phenomena of dimensional changes play independent and highly important parts. These kinetics, while not yet sufficiently studied to he formulated in the shape of physicochemical equations, might find their expression-in a qualitative systema-tization of the phenomena of precipitation according to two different viewpoints. To begin with, we encounter the question as to the velocities of the precipitation and of the growth of the phase precipitated. To harden a metal in an efficient manner we must be able to control the precipitation on one hand and also to bring the total of the secondary phase to such a number and size of the particles pre-cipitated as, will produce a desirable hardening effect under commercially feasible conditions of. age or heat hardening. From this viewpoint six different cases may be dis-cerned.

Jan 7, 1928

By P. H. Dudley

When we see the magnificent passenger-trains of from 8 to 12 coaches, drawn by locomotives weighing from 100 to 110 tons, at speeds of from 50 to 60 miles per hour between terminals, to make a schedule of 45 miles per hour, and freighttrains of from 50 to 75 cars of 60,000 pounds capacity, drawn by one locomotive, it is hard to realize that it lacks a few months of fifteen years since my pioneer 5-inch 80-pound rail for the United States was laid by the New York Central aid Hudson River Railroad Co., in July, 1884, on the Harlem line. Shorter passenger-trains, of from 4 to 5 coaches, are run much faster, notably the Empire State Express, the schedule of which for the 440 miles between New York and Buffalo requires 53.3 miles per hour, calling for a running-speed, for much of the time, of from 65 to 75 miles per hour, while higher speeds are very common. On other railroads laid with my 5 1/8-inch 80-pound rail, speeds of from 60 to 75 miles per hour obtain in daily practice. On many of the important railroads east of the Mississippi high speeds of from 60 to 70 miles per hour are part of the daily service. So many instances of speeds of 90, and even 100, miles per hour have been recorded that they must be considered as likely to occur on important lines, and provision must be made for them in the track. Solid mail-trains of from 6 to 8 cars are run from New York to Chicago, 1000 miles, in twenty-four hours; and, commeneing with the present year, shorter trains are running from Chicago to San Francisco, 2000 miles, in three and one-half days. In the freight-service equally important progress has been

Jan 1, 1900

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

By John B. Porter

Within the last year or so, a great deal has been heard about Southern iron ; even the Eastern markets have felt the effect of the cheap Alabama ores and coals, and public attention has again been drawn to what is now getting to be an old story—the great mineral wealth of the South. The following paper is based on a report prepared several years ago for a special purpose; but since then, through association with Mr. C. B. Going in a large analytical practice and as chemists to the Queen and Crescent Railway, I have had opportunity to increase my material so greatly that the present paper is really a completely different work. I am under very great obligation to Mr. Going, without whose assistance my work would have been very incomplete, and have also been materially assisted by Mr. F. P. Dewey, of Washington, and a host of gentlemen connected with the railroads and furnaces of the South. The arrangement of this paper is not all that could be desired. Some localities of importance are very poorly represented, both in the description and the tables of analyses. This, however, was in most instances unavoidable, as the study has been done ill the intervals of professional work. I have visited almost all the localities described, and, in all cases possible, have taken my own samples, and have made careful per-

Jan 1, 1887

By J. P. Hammond, C. J. McHargue

THERE have been no publications on the wire texture, on the cold-rolled sheet texture, nor on the recrystallized sheet texture of vanadium. Since it has a body-centered cubic structure, it would be expected to show strongly preferred orientations such as are found in iron&apos; and molybdenum.&apos; The wire textures of body-centered cubic iron,3 tungsten," molybdenum,5 antalum,6 iobium,6 and brass6 have been found to have [110] directions lying parallel to the wire axis. Wires of iron,&apos; containing 1.95 pct V or 1.95 pct Si,7 and steel8 retain their texture upon recrystallization. Molybdenum9 and tungsttln&apos; wires retain their texture after recrystallization at low temperatures. A [loo] recrystallization texture has been reported for mo1ybdenum9 and for a Fe-Ni alloy (53 atomic pct Ni).10 The cold-rolled sheet texture for iron,&apos; mild steel," and molybdenum chiefly one in which the [110] directions lie parallel to the rolling direction and the (100) planes lie parallel to the rolling plane with a deviation from this position chiefly about the rolling direction as an axis. This paper presents the cold-rolled and the re-crystallized wire textures, and the cold-rolled and the recrystallized sheet textures for vanadium. The results show that the textures in vanadium are not significantly different from those reported for other body-centered cubic metals. The vanadium used in this investigation was the so-called "ductile" vanadium which has a nominal composition within the following limits:12 0, 0.05 to 0.12 pct; H, 0.001 to 0.004; N, 0.02 to 0.04; C, 0.03 to 0.07; and V, 99.8 to 99.9. The wires were formed by rolling annealed rods of 0.280 in. diam to 0.028 in., a reduction in diameter of 90 pct. The wires were then electrolytically etched to 0.005 in. diam and used as such for specimens. Annealed sheet was reduced 95 pct in thickness from 0.100 to 0.005 in. with a two-high, 4-in. diam mill using reductions no greater than 10 pct per pass. In order to avoid temperature effects, the sheet was allowed to cool between passes. X-ray specimens were made in the form of posts from the sheet. The sheet was mounted in a fixture and the edges were polished using metallographic technique. Each edge was alternately polished and etched during the last stages in order that all worked material would be removed. These post specimens were approximately square in cross-section. The specimens to be recrystallized were wrapped in tantalum foil, sealed in evacuated quartz tubes, and annealed at 1600°F. The X-ray data were obtained from transmission shots made with a 0.030 in. pinhole camera, and molybdenum radiation with a zirconium filter inserted between the specimen and film. The grain size was sufficiently small in both the cold-worked and recrystallized material to give satisfactory results with the specimens stationary. In order for the wire texture to be determined, transmission X-ray patterns were taken with the

Jan 1, 1953

By C. E. McCarthy, A. George Stern, Stanley J. Green

THE national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of I9I4-I8 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. WYOMINGITE DEPOSIT For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the southwestern part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world&apos;s largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, I2; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the wyomingite has a potash content averaging slightly higher than eleven per cent K20. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1944

By George Young

DURING the spring of 1910 I visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and, even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. The principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories.

Jan 2, 1916

By Richard P. Rothwell

IN the pear 1881, I visited San Domingo, in the interest of French capitalists, to examine and report upon certain "concessions" of gold-bearing gravel and quartz veins, on the Isabella and Jaina rivers and their tributaries. This district is periodically reported to he extraordinarily rich, and there is oast around it the glamour of the mysterious shipments of gold, credited, in romance and in more or less romantic history, to Columbus and the Spaniards of the fifteenth and sixteenth centuries. Since considerable sums of money and several valuable lives have been lost in the unsuccessful search for its profitable mines, it seems desirable to place on record Borne of the information collected concerning the value of these famous gold fields, with the hope of facilitating the work of those who may hereafter be called on to investigate these claims, and of preventing the unnecessary waste of capital. It is needless to add that the capitalists for whom my investigations were made abandoned the enterprise they had in view,although no doubt similar schemes will be brought forward many times in the future, as they have been in the past, under the fervent advocacy of too sanguine enthusiasts. Since the time of the Spanish occupation of the Island of San Domingo, in 1497, when Columbus Found the natives wearing ornaments of gold, more or less of the precious metal has been obtained annually by washing the gold-bearing sands of several of its streams. It is said that during the Spanish domination, when the native Indians were held in the most abject servitude, a certain amount of gold was required of each one as the rault of his labor. Uuder this

Jan 1, 1882

By Fred Hale

OWING to the large area included in the Yellow Pine mining district, and the-varied nature of its mineral deposits, a detailed geological description of the district could be covered only in an extensive monograph. This paper is intended as a description of the most prominent geologic features only with special reference to those of economic importance. The first mention of the district was in 1903 by J. E. Spurr,1 who briefly describes the structural geology of the Spring Mountain range. In 1906, H. F. Bain2 briefly described the Potosi mine. James J. Hill,3 of the United States Geological Survey, visited the district for a brief period in 1912, the result of which is an excellent reconnaissance report, covering the district in some detail but necessarily with brevity. Since that time, articles covering special features of the district have appeared in the technical press, including some by the writer, and a notable description of the Boss mine, by Adolph Knopf,4 appeared in 1915. Development of the district during the past few years has progressed so rapidly and with so many notable discoveries, particularly with reference to the rare metals, that a further description at this time may prove of interest. The writer&apos;s acquaintance with the district is based on 7 years&apos; continuous residence in the vicinity, beginning with the spring of 1910.

Jan 2, 1918

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

By Albert Sauveur

As THE years go by, names of distinguished metallurgists will be added to the list of Henry Marion Howe lecturers, and now and then an illustrious one, for to be chosen to deliver the Howe lecture will be, I do not hesitate to predict, a highly coveted honor. I pray, therefore, your indulgence, if I confess to a feeling of gratification in having been appointed the first of these lecturers. It does not follow, however, that I am losing all sense of proportion and that I have an exaggerated idea of the little I have been able to contribute to our knowledge of iron and steel. Indeed, I fully realize how small were my claims to so great a distinction. I realize, also, that those entrusted with the task of selecting a lecturer were actuated, in coming to a decision, by their knowledge of the long and intimate friendship that had existed between the leader we have lost and myself. For their generous impulse, I thank them from the bottom of my heart; and with becoming modesty, I take up my task as the first Henry Marion Howe lecturer. It would be pleasant and indeed most appropriate to devote this entire lecture to a eulogy of Henry Marion Howe and his work, but how short the time for so large an undertaking and how inadequate my qualifications! On Aug. 28, Sept. 4, 11, and 18, 1875, a series of articles appeared in the Engineering & Mining Journal entitled "What is Steel?" With one exception, these constitute the first professional paper of Henry Marion Howe. That was nearly fifty years ago, three years after graduating from Harvard University. He was then but twenty-seven years old and already his keenly inquisitive mind was actively at work. There is a touch of romance in this young metallurgist who, on entering his. scientific career, destined to be so brilliant and so fruitful, on the very threshold of it, seems to have selected as his motto "What is Steel?" Like a knight-errant of science, he started on his quest for an answer to that question, a quest which was to last forty-seven years and which death only brought to an end. And while thus engaged how many wonderful messages we received from him, each one bringing us nearer to the goal! How illuminating, inspiring and encouraging were those messages! How well-equipped he was to wrench from nature some of the secrets she so jealously guards! How broad his learning and how clear his

Jan 5, 1924

By T. Egleston

The importance of condensing the gases which escape from furnaces so as to save both the fine particles of ore carried off mechanically and those which are volatilized, has for a long time occupied the serious attention of metallurgists in all parts of the world. It was my good fortune during the last summer to visit the lead and silver works at Ems, near Coblentz on the Rhine, and through the politeness of Mr. Freudenberg, general director of the works, to study in detail their methods of condensation, and to receive from him the important results which have been obtained through a series of experiments lasting over a number of years. I have thought, that these results would be of great interest to the members of the Institute and to other metallurgists in the United States, and I have, therefore, with the assistance of Mr. Freudenberg, prepared a careful, detailed description of the construction of the flues, as well as an account of the various experiments which have been made with them, and the conclusions arrived at as the result of these experiments. It may be said, in general, that the reason why so little attention has been paid in the metallurgical works of the United States to the collection of flue-dust, is that we are not generally aware of the large amount of material carried off by the gases. This is owing partly to the fact that little or no attention is paid to the subject, and also to the fact that the assays, which are almost invariably made in the dry way, show a result so much below the real contents

Jan 1, 1883

By H. H. Waller, C. H. Brehaut

At the Jeffrey mine of Canadian Johns-Manville Co. in Asbestos, Que., automatic batched concrete from surface is placed underground pneumatically for distances of 2500 ft directly into forms or to a second placer for greater distances, through 6-in. pipe of high carbon steel. The use of Celite C-4-C in addition to the usual aggregates achieves greater compressive strengths, lowers cost, reduces segregation, and improves workability and placeability results. Each year 25,000 cu yd of concrete are placed without interrupting production and development work in the mine, making possible a cheaper concrete that can be poured wherever and whenever it is needed. In about 90 pct of the underground openings in the Jeffrey mine concrete is necessary to preserve them in their original sizes and shapes for production. In the remaining 5 pct, the greater portion is united with or without steel support. When large quantities of concrete were forecast for underground use at the Jeffrey mine, preliminary and first hand information regarding pneumatic placing was acquired from articles by Bernhardt and Swanson and visits to their respective mines.

Apr 1, 1956

By George J. Bancroft

Western Australia (often popularly called Westralia) comprises all of the Australian continent west of the 129th meridian. The latest census, that of 1895, gives it a population of 101,235 persons. It includes within its bouiidaries 975,920 square miles. About half the colony lies within the tropics. The climate varies but slightly, considering the vastuess of&apos; the area. The interior is dry and hot, and subject to very sudden changes. The coasts are warm, and the rainfall abundant, varying from 20 to 40 inches per annum. Perth is the capital and principal town, having a population of 20,000. Fremantle (pop. 9000), distant 12 miles, is the port of Perth, but because it is out of the track of the mail steamers, the mail and passengers are landed at Albany (pop. 3000) on St. George&apos;s Sound. A railroad, 338 miles long, connects Pert11 with Albany, and the running time of trains is about fifteen hours. Kalgoorlie is only about 200 miles from the coast at the little village of Esperance; but to reach Kalgoorlie one must land at Albany, travel to Northam, within 66 miles of Perth, and then east at an acute angle 325 miles to Kalgoorlie; in all about 600 miles. From Perth a railroad also runs to the Murchison gold-fields by way of Mingenew, Mnllewa and Yalgoo, to Cue. A branch goes down to the port of Geraldton. The government operates all the railroads and telegraph lines, and has been very energetic, all things considered, in extending them into the gold-fields. As to the accommodations afforded by the railroads, the less said the better. The comforts of travel are conspicuous by their absence. Of the 975,920 square miles of Westralia, the government, in its magnificent way, cleclares 256,060 to be gold-bearing. There are the Kimberley fields in the north, of 47,000 square miles; the Pilbarra on the northwest coast, of 45,600 square

Jan 1, 1899

Falconbridge Nickel, the one-time subsidiary that grew up to swallow its own parent, Ventures Limited, in 1962, is not about to be left behind by rising nickel consumption. At a cost of several hundred million dollars, this Canadian firm has undertaken a series of new projects that will not only ensure its present share of the market, but also lead it into new areas of the nickel business. Although Falconbridge Nickel Mines Ltd. was not formed until 1928, it actually had its start in 1917- 18 with the discovery of a large, good grade nickel- copper deposit in Falconbridge, near Sudbury, Ontario. However, due to several factors, financing could not be obtained and the orebody lay fallow. It was not until 1928, when the Thayer Lindsley interests bought the property from the original owner, that it was developed.

Jan 10, 1968

John S. Kennedy, Chamhersburg, Pa. (communication to the Secretary): The washing-plant described by Mr. Johnson is a good illustration of the advantages derived from a well-designed and care-

Jan 1, 1895

By S. F. Emmons

There is, in the southern part of the State of Illinois, a series of deposits of fluorspar and galena in which the former mineral occurs on a scale of magnitude unequalled, so far as I know, in any other part of the world. In June, 1891, 1 had an opportunity of visiting the region of their principal development, near Rosiclare, Hardin county, Ill., and examined such of the mines in the vicinity as were accessible at that time. A very large proportion of the mining shafts that had been sunk in this region were unfortunately abandoned for the time being, and full of water. Moreover, detailed maps of the region are unattainable, no surveys having been made there, apparently, since the original land-surveys&apos; of the early part of the century. In spite of these disadvantages I was enabled, in the few days at my disposal, to ascertain with sufficient accuracy certain facts not hitherto published with regard to these deposits, which seem worthy the attention of the members of the Institute. Before proceeding to a description of the deposits in question, I will give a brief abstract of the little historical and geological information hearing directly or indirectly upon them, which I have been able to find in existing publications. Historical. That the mineral was known to the Indians, is proved by the discovery, in some of the pre-historic mounds of the region,* of fluorspar, shaped into ornaments. The earliest scientific mention of its occurrence is found in the first volume of the American Journal of Science (1818+), which describes specimens obtained in the vicinity of Shawneetown by Mr. Joseph Baldwin. Similar notices appear in the same journal in 1820 and 1821, but without mention of the exact locality. They remark on the fetid odor which characterizes the mineral and its association with galena. Schoolcraft, as early as 1819, note: the occurrence of fluate of

Jan 1, 1893