Search Documents

By J. K. Whyatt

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that. within the scope of this study, the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard. However, much work will be required to make good on this promise.

Jan 1, 1998

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By N. P. Kripakov

The U.S. Bureau of Mines (USBM) is conducting research to develop a practical computer-based tool that will allow coal mine planners to anticipate rock mass behavior surrounding mine entries prior to actual mining. More specifically, this tool estimates to what degree and extent the immediate roof and floor strata and the coal pillar ribs surrounding an opening will weaken or fail for a given set of mining parameters. The technical approach couples together two numerical techniques: the boundary-element method and the finite-element method to allow for an approximate three-dimensional simulation of actual mining situations. Outputs from plan-view, linear-elastic, boundary-element models executed at different mining stages are used as input to a detailed, section-view, finite-element model to estimate the degree and extent of failure expected to occur around the periphery of an entry system. Using a pseudo-elastic approach. elastic rock mass properties are continually updated as different zones are predicted to fail. The procedure is relatively easy to use and is being set up to work interactively with the user who will not be expected to be a computer expert. Inputs include easily understood parameters obtainable from the field and rock mechanics laboratories. Examples of computer-generated output from generic sample models representing typical mining situations are presented and results discussed.

Jan 1, 1994

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By J. S. Oram

Maltby Colliery, operated by RJB Mining (UK) Ltd is successfully mining the Parkgate seam in Yorkshire at a depth of 1000m using longwall retreat. Extraction in the Parkgate seam is influenced by interaction from previous workings in the Swallow Wood Seam 160m above. The paper describes in-situ stress measurements and simple gate road convergence measurements carried out to assess the extent of the interactive influence. The stress measurements, obtained using the stress relief overcore technique, were carried out from a maingate development roadway in an area where the stress redistribution under an overlying pillar and adjacent panel goat could be measured. The measured vertical stress distribution confirmed a significant interactive influence with high imposed vertical stresses under the overlying panel edges. Simple roadway convergence monitoring stations established in the gateroads of a retreating panel and in the development gateroads of the adjacent panel, confirmed higher rates of roadway deformation relating to overlying panel edges and pillars, particularly in the areas where a vertical stress window developed during panel retreat. In addition to highlighting a close relationship between closure rate and the measured vertical stresses, the convergence monitoring proved valuable in establishing characteristic deformation behaviour under specific interactive influences and also in defining the optimum location, extent and time of installation u£ additional roadway support and reinforcement. The information from the measurement programme has enabled the Mine Management to gain a better understanding of the interactive influences on roadway behaviour and was instrumental in designing the layout of panels in an area of the North East district of the mine where previous experience had indicated the combined influence of high interactive stresses and weak roof lithology resulted in difficult strata conditions both at development and on panel retreat. The planned location of panels and gateroads took into account both mining operational considerations and the need to avoid potentially high risk interaction zones as highlighted from analysis of the monitoring results. To obtain additional data on parameters influencing roadway deformation, extended roadway convergence monitoring has been established.

Jan 1, 1997

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Bob J. MacDonald

The Cape Breton Development Corporation is a federally owned Crown corporation in Canada that operates two coal mines the Prince and Phalen Colliery in the Province of Nova Scotia. Retreat longwall mining was first introduced to the shallower workings (I 80m) of Prince Colliery in the early 1980's. Phalen Colliery started longwall retreating in 1987 and since that time has extracted twelve panels. In 1993 there had been a total of eight longwalls varying in widths from 140-230m mined in Phalen Colliery that is on the Phalen Seam. Up to this point there were only minor ground control problems on the faces except for one of the earlier longwalls that was mining a split seam. There is some interaction on Phalen workings from remnant structures in the overlying Lingan and No. 26 Collieries which worked the Harbour Seam. Induced abutments loads along pillar edges have been observed and resulted in poor face conditions when mining the Phalen Seam. The ninth panel, 6 East was the first panel to suffer a major roof fall from the First Major Weighting. This was also the first panel to undermine a paleo sandstone river channel named the Lower Sandstone Unit (LSU). For the first time in Phalen's history subsequent longwalls began to experience periodic weighting events. The 6 East panel suffered a number of periodic weightings and on two occasions had to use foam cement to fill the cavities that resulted. On the next east side panel, 7 East, there were numerous periodic weighting events, but interestingly there was no significant First Major Weighting. 7 East was the first 260m wide panel and all others were 230m or less. This longwall was 3,400m long and began producing in December of 1994 and was still cutting coal in May of 1997. There were five significant roof fall events on this panel, three of which required foam cement to fill the cavities. Of these three the interruption to production varied from four days to seven months. There were definite precursors to each of the weightings including: 1) an increase in audible noise (termed bumping) on the face, 2) supports went rapidly into yield, 3) roof convergence increased, 4) water percolated from the face roof strata, and 5) severe spalling of the coal occurred resulting in increased tip to face distance. Longwall face weightings are a result of geomechanical factors and cannot be avoided However, the loss of roof control is a different matter and highly subjective to operational procedures. The causes of weightings, their magnitude and impact on the mining at Phalen have been investigated. The following factors have been identified as relevant to these occurrences. 1. The influence of pillars in the overlying Harbour Seam workings. 2. Location of the LSU relative to the Phalen Seam. 3. Thickness of the LSU. 4. Pressure arch effect from the adjacent gobs. 5. Poor operational practices on the longwall including: a) slow rate of retreat; b) inadequate supply of pump pressure to the hydraulic supports; c) premature yielding of the yield valves; and d) poor face alignment practices. This paper will review the events that took place on the 7 East longwall and show that the Lower Sandstone Unit is the primary cause of the weightings. However, other factors contributed to the loss of roof control and the formation of the roof cavities.

Jan 1, 1997

By E. Hosca

Alternative tailgate loading conditions due to conventional and conventional/yield pillar combinations were evaluated to define roof loading. In order to isolate different loading situations, the tailgate entry was considered as part of the roof-pillar-floor system, which is controlled largely by the structural integrity of each member. A data bank of case studies was compiled, which contains details of roof and floor lithology, structure, support, and mining data, including any failure modes. The range of loading conditions that any tailgate can be subjected to was identified to form the basis of numerical modeling. Numerical modeling was then conducted on tailgate openings to determine roof, floor, and rib responses, including failure modes to a variety of loading conditions. Trends developed from the numerical modeling were modified using field data to form the basis for support evaluation and application. The effects of support were modeled numerically to determine optimum load capacity and points of application for reducing the potential for entry failure.

Jan 1, 1994

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

By Dale S. Preece

In 1975 Congress passed the Energy Conservation Act to establish a U. S. Strategic Petroleum Reserve (SPR) with a capacity of 750 million barrels of crude oil. The most economic storage medium was determined to be salt caverns leached in salt domes in Louisiana and Texas. Salt caverns existed at several sites when the reserve was created. These were obtained by the U. S. Department of Energy (DOE) and used to initiate SPR oil storage. In order to meet the storage capacity approved by Congress, new caverns also had to be leached. To support the resulting design effort, finite element computer program have been used to determine the creep closure and structural stability of salt caverns. Using site specific material properties including creep models, elastic moduli and fracture data, the finite element analyses have replaced earlier empirical approaches to cavern design. This report presents results of such finite element analyses to determine the best cavern roof shape and the minium pillar to dimeter ratio. , P/D. These numerical predictions indicate that the current cavern design is safe.

Jan 1, 1984

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

By Peter Hayes

Moonee Colliery operates a longwall extraction system in the Great Northern seam of the Newcastle Coal Measures, approximately 100km north of Sydney, NSW. In the initial mine area of longwall blocks1-4a, the Great Northern seam is overlain by a massive conglomerate approximately 35m in thickness. Unanticipated sudden, blocky caving of this material has produced windblasts with associated velocities of 100m/sec and over-pressures of 35kPa. Although these events have not resulted in fatality, the potential safety risk to face personnel was such that the mine was threatened with closure. The development of a Windblast Management Plan to minimise the exposure to windblasts, a Micro-seismic Management flan to predict caving events, and the use of hydraulic fracturing to generate caving on demand, have all contributed to the salvation of the mine. Prior to the introduction of hydraulic fracturing, falls were highly variable and ranged in goaf area from 2000m2 to 30,000m2 with an average of around 7.000m2. Hydraulic fracturing has introduced consistent and far less variable falls, planned as averaging around 5000m2 and all accompanied by microseismic warning, Moonee Colliery is believed to he the only operation in the world using real-time microseismic warning and using hydrofracturing as a day-to-day operational process. These processes have enabled it to return to financial viability in an environment of strict procedural control, whilst ongoing efforts are made to optimise and enhance these systems. Moonee's story is a case study of the successful application of research and development work to the economics of a mine.

Jan 1, 2000

By E. Bane Kroeger

Rib failure is a hazard that has resulted in many injuries and fatalities in underground coal mines, especially in soft coal seams. Conventional rib control methods including rib boarding, shotcreting. steel meshing and geogridding, are fairly expensive and time consuming to install. Some methods, such as rib boarding, have met with marginal success at controlling rib failure. Under this research, the Rib Strap System (RSS) introduced by Dr. Chugh in 1999, was modified and new components were added. Both bench scale and full size prototypes were tested in the labs at SIUC to determine the best materials for fabrication and easier methods for assembly and installation. This laboratory research has developed new methods of securing the strap ends to smaller rib hoards, a new device to post-tension two straps together, and a technique for replacing straps without having to drill new rib bolts or for retrofitting straps to rib hoards that are already in place. The method used to secure the strap end to rib boards developed during bench-scale testing was dubbed the wrapped staple technique. It is very simple, requiring only 10-15 staples, with the end of a strap secured to a rib board in about 45 seconds. Several different prototype designs for a new device to join the strap ends together and tension the strap were fabricated and tested in the labs at SIUC. The device, dubbed the rib strap buckle, was very easy to install and held the straps firmly. One specific buckle design worked extremely well during testing and exceeded all expectations. The laboratory research also developed a method of replacing a damaged rib strap that can also be used to add rib straps to existing rib boards. The technique uses nails, spacer blocks, and band clamps to secure the new board and strap. This technique was developed to allow one person to replace a strap using only a hammer and screwdriver, negating the need to drill and install a new rib bolt using mine equipment such as a roof bolter or scoop. In addition to the technical feasibility, the cost of materials for the rib strap system was compared to the rib boarding method currently being used at a mine in the Illinois Basin. The mine is using 20 rib boards on each pillar at cost of about $223.60. The costs for the rib strap system depend on the materials chosen for fabrication but for the base case, were about $97 per pillar.

Jan 1, 2004

By Krzysztof Tajdus

In Europe, horizontal strain is a primary parameter for estimating building hazard resistance. Other measured indices, like curvature, are less important, since in most cases of European excavation depths are very large (about 1,000 m (328 ft)) and, in such circumstances, curvature influence decreases. Therefore, a proper description of horizontal displacement (and strain) in the scope of minimizing influence is essential. This article presents a development of European methods of horizontal displacement and horizontal strain calculations, as well as current solutions in this respect.

Jan 1, 2011

By Jisheng Han

Interaction effect exists when two or more neighboring seams are mined. The mining activity in one seam causes stress redistribution and strata movement in both the roof and floor. When the thickness of interburden between two neighboring seams is small, some hazardous situations like roof cutters, roof falls, floor heave and rib spalling in one seam may be encountered due to the effect of the mining activity in the other seam. An investigation about roof cutters, roof falls and floor heave was conducted in a West Virginia mine to study the interaction of multi-seam mining. The mine is mining the Sewickley Seam, which is about 90 ft above the Pittsburgh Seam which was mined in the 1960's using room and pillar method. The roof falls and other stability anomalies of entries observed underground in the Sewickley Seam were found closely related to the location of barrier pillars and gas well pillars left in the Pittsburgh Seam. Then numerical modeling was carried out to check the interaction between these two seams of mining. It was found through the modeling results that in the areas where pillaring operation was conducted in the Pittsburgh Seam, the stress concentrated less in the Sewickley Seam while near the edge of the gas well pillars and barrier pillars, high stress concentration was observed. It was concluded that under the geological conditions of the study mine, the entries stability would be affected by the lower seam mining activity, especially above or around the edges of pillars.

Jan 1, 2005

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982