Search Documents

By W. C. Brice

Minnesota's mineral resources are widespread and diverse (Figure 1). In addition to the nation's largest iron and manganese reserves, the state contains sizeable vanadium, copper, and nickel resources. Recently it has been determined that the proterozoic unconformities in Minnesota have a favorable potential for uranium deposits. Finally, major potential exists in Minnesota's archean greenstone belts for gold, silver, and copper-zinc massive sulfides. Many of the state's mineral resources have been found in environmentally sensitive areas. This is not surprising since the natural forces associated with the formation of mineral deposits are often the same processes that create unusual landforms. For example, much of the state's copper-nickel is found within and adjoining the Boundary Waters Canoe Area (BWCA) and Lake Superior. The history of mineral development on the Mesabi Iron Range has also created culturally sensitive areas. Early iron mining development required the workers to live close to their jobs, and mine wastes were dumped as near the mine as possible. Few, if any, foresaw the time when taconite would be economic to mine. Therefore, it is not unusual to find valuable taconite resources located under towns and waste dumps on the Mesabi Iron Range.

Jan 1, 1980

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation' or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By Thomas Hard

A description is given of a new facility processing blast furnace slag into a high quality cementitious material to be used as an ingredient in concrete for general construction purposes. A brief history of the process is given, followed by a detailed discussion of the water granulation system and the methods used to transport and dewater the granulate. Environmental advantages of handling slag away from the blast furnace by water granulation are included.

Jan 1, 1983

By D. W. Rierson

Svedala has a ported kiln process, designed specifically for the direct reduction of pelletized or natural lump iron ores. The process is called ACCAR. This ported kiln technology has been coupled with Svedala's GRATE-KILN System, for iron ore pelletizing, into the GRATE-CAR System for the reduction of fine grained ore concentrates through the steps of agglomeration, induration and reduction in a single production line. Additional applications of the GRATE-CAR System include: the recovery, agglomeration and reduction of steelmill waste oxide fines and the use of minus 6mm size natural lump ores to produce a highly metallized pellet agglomerate. Svedala conducts tests to confirm certain operating parameters through process simulations of the GRATE-CAR process. These tests are conducted at Svedala's Process Research and Test Center, Oak Creek, Wisconsin. Svedala also assesses issues of process variables, heat transfer, equipment sizing, retention time and endothermic demand associated with iron ore reduction using natural gas or coal as the reductant. The purpose of this paper is to present the GRATE-CAR processing concepts, the commercial production line and the testing procedures associated with investigating potential raw materials.

Jan 1, 1997

By Roberto L. Romero

The dressing of Bolivian tin ores has been done up to the present by classical. gravity methods, taking advantage of the high specific gravity of cassiterite compared with that of the accompanying gangue. For this purpose, jigs and shaking tables are used in the treatment of the various size fractions in which the ore is classified. Bolivian ores are mainly of the vein type and, to obtain a reasonable separation, crushing and several stages of grinding are necessary during the process to substantially liberate the cassiterite from the gangue. Gravity processes for cassiterite are effective for sizes down to 200 mesh. Below this size the efficiency of the gravity methods falls off very rapidly with increasing fineness of the mineral grains. The conventional treatment for this material is desliming followed by tabling on shaking tables various other types of machines have been designed for the gravity treatment of these fine particles but they have had limited success. Bolivian ores contain an appreciable amount of minus 200 mesh material constituted by "primary fines" caning from the mine itself, and "secondary fines" originated during the crushing and grinding necessary for liberation of the difficulty in the treatment of these fine particles is one of the causes why the recovery of tin in concentrates is only of around 50% in the mines owned by Corporacidn Minera de Bolivia, the State owned enterprise. The average figure for other Bolivian mines is

Jan 1, 1971

By K. C. Shaver

The Sloan Ranch kimberlite complex is located approximately 130 km north-northwest of Denver in the Precambrian core of the northern Colorado Front Range (Figure 1). A Devonian age for the complex is suggested by the fossil assemblages in limestone xenoliths (Chronic and others, 1969), and by paleomagnetism of the kimberlite (E. E. Larson, personal communication, 1986). The presence of diamond was first reported in rocks from the Sloan diatreme by McCallum and Mabarak (1976). Prior to this time, the distinctive- appearing host rock of the Sloan diamonds had been quarried for use as terrazzo stone; examples may be seen in the floors of the airports in Cheyenne and Laramie, Wyoming. The Minerals Division of The Superior Oil Company obtained a lease on the Sloan property in 1980. During the next four years Superior built and fine-tuned a highly efficient diamond recovery facility, explored and tested the Sloan deposit, and used Sloan as a site for testing numerous exploration techniques for future use in a continuing exploration program in the Colorado-Wyoming kimberlite province. The Sloan property was ultimately determined to be sub- economic, but the lessons learned there have been very helpful in subsequent exploration efforts.

Jan 1, 1987

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By John A. L. Campbell

Although there has been an increased interest in the electrokinetic properties of coal (1) research on the subject is still in an early stage of development (2,3,4,5,6,7) To the author's knowledge, no electrokinetic studies have been made on coal lithotypes - particularly anthracite lithotypes. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods, It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published (8). The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results, however, the results are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation.

Jan 1, 1969

By C. D. Atkinson

The past few years have seen a much greater concern about air pollution in this country. This concern has led to increased legislation restricting the discharge of many substances such as sulfur dioxide and particulate matter to the atmosphere. In the future, it is anticipated the present permissible emission levels will be lowered. Current and impending restrictions on the emission of sulfur dioxide have brought out the fact that there is a shortage of available low-sulfur fuel for power plants and industrial use which promises to have an economic impact on the nation's energy picture (1) The Pittsburg & Midway Coal Mining Co., under the sponsorship of the Office of Coal Research, has developed a process to produce a fuel capable of meeting the energy requirements of this nation (2) The process is called "The Pittsburg & Midway Solvent Refined Coal Process". The principle product from the process is Solvent Refined Coal which is an ashless, low-sulfur fuel with 16,000 BTU per pound regardless of the rank coal from which it is produced. The product can be burned as either a solid or a liquid fuel. The process appears to be economically more attractive than other methods of alleviating the pollution problems of this nation. In addition to reducing the air pollution caused by stack gases, the product produced is potentially useful as a source of electrode coke and electrode binder pitch, as a gas turbine fuel, in the production of metallurigical coke and pavement asphalt, and as the first step in the overall process to produce distillate fuels and pipeline gas (3).

Jan 1, 1973

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By X. Li, J. C. Stankus, J. Ma, H. Chen

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult, because a slope will transverse through many types of strata. Over the last few years, Keystone Mining Services LLC, an affiliate company of the Jennmar Corporation, has developed a new methodology designated the “Stress, geologic and support design system (SGS).” The method analyzes the stress, geology and support design for a mine slope. The method has been successfully applied in various new slopes across the United States, and ground control plans developed using SGS methodology has helped coal companies successfully pass review and/or hearings by state and federal regulatory agencies. With a case application in the U.S. Midwest, this paper details and demonstrates the main concepts of the methodology, including (1) analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) primary and supplemental support design; (3) long-term support design in the form of steel square sets or arches and (4) validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By Robert L. Bates

In this paper I use the term "industrial minerals" in its broad general sense, and I distinguish two main groups. The first consists of the bulk materials, characterized by low unit price, nearness of deposits to markets, relatively simple methods of extraction and processing, and a tendency to be closely related to the construction industries. The second group includes those materials valued for exceptional purity, or for some special property such as hardness, immunity to acids, or dielectric strength. These materials are produced in smaller amounts, at high unit values, from deposits notably restricted in. distribution; and they require more or less sophisticated methods of production and beneficiation. The applications of this second group are not closely tied to any particular part of the economy. From the way in which the commodity committees of the Industrial Minerals Division are set up, I take it that the chief interest of most members is with the first group of materials mentioned above. Hence this paper will deal mainly, though not exclusively, with such bulk commodities as sand and gravel, clay, and stone. The first word in the title of the paper also requires brief explanation. It is here given a threefold interpretation. First is the role of the industrial minerals themselves in industry; this would probably be taken as the conventional meaning of the title* The second is the role of the industrial-mineral producers as citizens of the community. The third is what may be called the scientific role of these producers.

Jan 1, 1964

By L. P. Meade

The particular impact of imported industrial minerals varies within the Industry and is dependent upon many diverse factors. In a similar way, the impact on individuals has been varied and the degree of impact will depend partially on the individual's ability to handle change. Just as many corporations are adjusting their marketing strategy and production methods to compensate for imported mineral products; individual managers, mining engineers and geologists are making adjustments to their own personal job marketing techniques and on-the-job operating procedures. Modifying the degree of impact for both industry and individuals depends upon the ability to adapt.

Jan 1, 1988

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By Wi11iam M. Leaders

Uranium Recovery Corporation was incorporated in the State of Florida in 1968 for the sole purpose of developing a method to economically recover uranium from Florida phosphoric acid. The preliminary laboratory work culminated in the demonstration of the process to United Nuclear Corporation in the spring of 1971. This was quickly followed by a pilot plant program to identify any unusual problems such as those arising from the day-to-day variation which occurs in a fertilizer phosphoric acid plant production system. After two years of pilot plant operation, United Nuclear Corporation purchased controlling interest in Uranium Recovery Corporation and committed several million dollars to the design and construction of the first commercial plant for this purpose in the State of Florida, or anywhere else in the United States, for that matter. After many start-up problems were resolved at the production plant located at the W. R. Grace fertilizer complex near Bartow, sustained production began March, 1971, and has continued to date. We still have some problems to solve but are currently producing sufficient uranium to make shipments to the UF6 converters for preparation of Florida uranium for use in nuclear power plant fuel materials.

Jan 1, 1978

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982