Search Documents

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By Oscar H. Lentz

During 1960, the controversy over percentage depletion reached the level of debate between presidential candidates. Nixon took the position that he would not tamper with the status quo in this matter. Kennedy took the position that he was willing to take a fresh look at the issues involved. Kennedy's position appears to have been based upon two premises: (1) new sources of federal revenue may be needed; and (2) current depletion rates, even if sound in principle, may be too high and, therefore, inequitable. The latter premise constitutes the basis for the claims that depletion allowances are simply "loopholes" of tax avoidance. Very probably the controversy over percentage depletion will remain in the political limelight during most of the coming decade. It is quite possible that the current depletion rates, at least those for oil and gas, will be reduced during this period. The aim of this paper is to isolate the complex causes of this mounting opposition to percentage depletion.

Jan 1, 1961

By R. D. Williams

Several hydrometallurgical leach processes have been recently proposed for the recovery of copper from copper concentrates. These include the Cymet Process of Cypress Metallurgical Processes Corporation, the Arbiter Process of the Anaconda Company, and the Treadwell Process of Treadwell Engineering company(1). These processes and similar processes for recovery of other minerals, have several phenomenological similarities which make their quantitative description difficult at best. These include (a) the presence of more than one phase, (b) non-uniform mineralization of the feed concentrate, (c) surface and diffusional effects, and (d) a particle size distribution which varies with time. Semi-theoretical, rather than purely empirical, treatment of such processes in their developmental stages will result in a better understanding of the physico-chemical mechanisms in effect. This, in turn, will allow reliable process designs to be made on reasonable time scales for reasonable development costs. Once a production unit is built, such an approach will provide straightforward methods for process control and optimization. A research and development effort to determine criteria and procedures for semi- theoretically characterizing such mineral leach recovery processes has been initiated in a joint venture by the Arizona Bureau of Mines and the College of Mines at the University of Arizona. This group has as its task the mathematical characterization of hydrometallurgical leach recovery processes using semi- theoretical mechanisms for the underlying phenomena. The resulting models are experimentally verified and parameterized on the laboratory scale in such a way that they can be utilized with similarity criteria to provide reliable scaleup to production designs. This discussion will be centered around the elements of such an approach and how they fit together.

Jan 1, 1975

By W. H. Renison

This paper will discuss the operation and maintenance of Molycorp's Quests Mine ore conveyor system. The 1.2 m wide, steel cable-reinforced conveyor belts are capable of transporting 1089 kt/h of ore over a belt line distance of 3124 m with a vertical rise of 518 m. A portion of the conveyor runs in a 2057 m long underground decline on a 10° slope. Six 448 kW motors power the main 1.2 m wide belts.

Jan 1, 1984

By R. W. Draves

Planning and testing in advance of the mining operation are essential. This advance work can involve physical and chemical analysis of overburden cores, field test plots, green- house studies or any of a multitude of other baseline data collection activities. This paper presents the results of Central and South West's field test plots and how they relate to topsoil substitution. Besides the obvious need for testing in advance of mining, there are the inevitable regulatory requirements. Quoting from the office of Surface Mining Regulations concerning topsoil substitution: 216.22(e) TOPSOIL SUBSTITUTE AND SUPPLEMENTS -Selected overburden materials may be substituted for or used as a supplement to topsoil if the office determines that the resulting soil medium is equal to or more suitable for sustaining revegetation than is the available topsoil and the substitute material is the best available to support revegetation.

Jan 1, 1985

By R. G. Reddy

Solid state reduction of roast movat chromite ore with carbon was carried out as a function of C/FeO ratio and temperature in the range 800°C to 900°C by thermogravimetry analysis (TGA). A two stage mechanism, (1) the reduction of FeO present in Roast Movat with carbon monoxide; and (2) the regeneration of CO by the oxidation of carbon with CO2 was proposed. The rate controlling step is the carbon oxidation reaction. A kinetic equation, that of random nucleation, was proposed. The activation energy for the reduction was determined to be 55800 J/mole and is compared to those activation energies determined for other chromite ores.

Jan 1, 1998

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade by the late 1990s, longwall mine output accounted for 40% of all underground output in the U.S. and today longwall mines account for approximately 50% of coal produced underground in the United states. A 51% increase in average shift production rates has occurred over the last 15 years. this increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust presents an ongoing challenge for coal mine operators the National Institute for Occupational safety and Health (NIOSH) conducted a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify the dust levels generated by major sources on the longwall section and to identify different control technologies in use today substantial reductions in dust levels were realized at sampling locations on the face when compared with ongwall surveys conducted in the 1990s results from the underground dust surveys and current longwall dust control technology and operating practices will be discussed. Mining Engineering, 2011, Vol. 63, No. 9, pp. 74-80. Official publication of the society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By Sean Cassady, Jason Liu, Sanja Zlatanic, Taehyun Moon, Chris Devery

"For the Hollywood International Airport Runway Expansion Project at Fort Lauderdale, Florida, the structural fire durability analysis was completed for a series of tunnels formed by roadway and railroad cells located under the runway structure. A systematic design approach was developed to mitigate structural damage during a fire event and arrive at a practical method to structural fire engineering that is compliant to NFPA 502. To ensure the NFPA 502 requirements are satisfied, the performance based approach was implemented and the engineering analyses were performed for the adopted design fire event. The analyses considered the facility’s unique features including its fire safety systems to determine applicable design fire curves for structural durability analyses. The paper also outlines the process of defining the project specific fire curves for a specific design fire scenario and summarizes the results of heat transfer and structural fire durability analyses. This approach was aimed to assist the owner and Authority Having Jurisdiction to achieve practical decisions to the tunnel facility fireproofing.INTRODUCTIONFort Lauderdale–Hollywood International Airport (FLL) in Broward County, Florida is a major hub facility serving more than 23 million passengers annually. As part of the Airport Expansion Program, the South Runway (9R-27L) Expansion project aimed to meet ever increasing service demands via an increase to runway lengths. This necessitated the placement of one of the reconstructed runways on bridge structures over the existing U.S. Route 1 (US 1), a major north–south U.S. Highway that serves the East Coast of the United States, and the Florida East Coast (FEC) Railway, thus effectively creating multiple tunnel cells beneath the subject runway. For this project, HNTB suggested a tunnel fire damage mitigation system that would protect the runway major structural elements from the design fire event that may happen within the tunnel cells. This paper addresses the issues related to the fire event originating within the tunnel encompassing the US1 highway only, and deals with requirements of NFPA 502 [5] exclusively. Therefore, while approaching the structural fire protection issues for the specific tunnel cells beneath the runway structure, the requirements of the American National Standard NFPA 502 (Standard for Road Tunnels, Bridges, and Other Limited Access Highways, 2008 edition) were followed. Per this standard, regardless of tunnel length, all primary structural concrete and steel elements shall be protected in order to:"

Jan 1, 2016

A kinetic model for leaching of various metals with different lixiviants in a batch system has been developed. Material balances for reactants and products at the solid/liquid interface were formulated and solutions to these balances were obtained in view of practical conditions. Special emphasis has been given to examine mixed controlled reaction systems where both heterogenous reaction and mass transfer play important role on the overall rate expression. The resulting kinetic expressions for either powder or rotating disc are discussed in light of experimental findings for various metals. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1992

By L. Blain

In practice, geochemical analyses can be grouped in two broad categories according to their aim. Those that seek to determine the exact chemical composition of geological materials fall under the heading of assays, whereas applied geochemistry concerns itself with the detection of anomaly contrasts. Recent trends have blurred the distinction between both approaches for many users, as methods that were traditionally used for assays are being adopted in applied geochemistry and assays make increasing use of instrumental techniques. Nevertheless. it is important to keep a clear distinction between the two types of analyses because it has immediate practical consequences, cost is the most obvious, as well as fundamental implications. In the broadest terms, the goal of geochemistry is to strike an optimal balance between throughput and accuracy, at the lowest reasonable cost, while assays strive for accuracy. Traditionally, complete silicate analysis has been the concern of assayers whereas exploration geochemists have been more interested in base metal analyses where acid extractions of the elements, without dissolution of the silicate matrix, has been the norm. This kind of distinction is less realistic now, especially with the growth in lithogeochemical studies, and some overlap in methodology is unavoidable. However, where such overlaps occur the distinction remains in the emphasis of the work. A commonly used example is that although HF acid preparations are used by both, the emphasis in applied geochemistry is on sample throughput and batch analysis, whereas assayers are more concerned with the range of elements to be determined (Thompson and Walsh, 1983).

Jan 1, 1993

By Mike Hall, Tim Kelly, Mohammad Reza Jafari, Ulf Georg Gwildis

"Qatar’s capital Doha is undergoing major infrastructure improvements including a multiphase stormwater management program. Although located in an arid climate, Doha experiences flooding during rainfall events. Dewatering operations and rising groundwater levels add to the management needs. To address those needs, construction of the Musaimeer collection tunnel along Doha’s southern rim is being followed by a marine outfall tunnel connecting a pump station to a dispersion field 10 km offshore. Qatar’s geology is characterized by sabkha deposits, a series of predominantly weak and karstic rock strata that creates challenging conditions for mechanized tunneling, as highlighted by the uncontrolled flooding of a tunnel boring machine (TBM) used on the Doha Metro tunnels. Risk associated with these challenges is magnified for the outfall tunnel by drive length, sub-sea elevation, and a single access point. This paper describes the outfall exploration strategy and design decisions made in light of experience gained during the collection tunnel construction. CONTEXT – STORMWATER MANAGEMENT PROGRAM Qatar has an arid climate with an average annual precipitation of less than 100 mm. Precipitation is mostly confined to the winter months when rare, but occasionally heavy rainfall events easily lead to flooding in Doha’s metropolitan area. Its coastal location and flat topography a few meters above the sea level mean that the depth to the groundwater table is generally shallow. The karstic aquifers in the regional dolomite and limestone series contain groundwater of high salinity, which is not suitable as a potable water source. For supplying Doha’s population of more than 900,000 (2014) with potable water, the Ras Abu Fontas seawater desalination plant is operated about 10 km south of the city. This potable water production capacity is crucial for Doha’s development and – in conjunction with overirrigation and leaking sewage tanks – is also the root cause for rising groundwater tables that have been observed over the past years."

Jan 1, 2016

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Most, if not all longwall gobs contain explosive gas zones (EGZs), i.e., zones of explosive methane-air mixtures that can cause – and have caused – mine fires and explosions. If the coal is prone to spontaneous combustion, oxygen penetration into the gob must be avoided. This paper summarizes the significant research findings from five years of computational fluid dynamics (CFD) modeling research conducted at the Colorado School of Mines (CSM) under funding from the National Institute for Occupational Safety and Health (NIOSH). CSM Researchers have developed CFD modeling techniques to identify where and under what circumstances EGZs can form in longwall gobs and how EGZ formation and oxygen penetration depend on the ventilation method, face and bleeder ventilation parameters, injection of inert gases and the operation of gob ventilation boreholes. Recognizing these explosion and fire hazards is an important first step in improving the safety of longwall coal mines. CSM modeling research has shown that EGZ formation can be effectively controlled by adjusting ventilation parameters, choosing the proper ventilation pattern and injecting inert gases where necessary. INTRODUCTION In a project sponsored by the NIOSH Office of Mine Safety and Health Research, researchers at the Colorado School of Mines have examined gas compositions and flows in longwall gobs in order to assess explosion and fire hazards. Since gob areas are inaccessible, researchers developed a series of computational fluid dynamics (CFD) numerical modeling tools to characterize these hazards. A variety of CFD models were developed to cover progressively sealed as well as bleeder ventilated gobs for both coal and trona mines. The explosion and fire hazards posed by EGZs in longwall gobs can be summarized as follows.• If the EGZ lies closely behind the longwall face, flames and pressures from an explosion can penetrate the shield supports and reach the active face area, creating blast trauma, burn hazards and toxic, unbreathable atmospheres. • EGZs can be pushed around inside the gob by roof collapses and cave-ins. If they get pushed out into the face area, sudden methane inundations and explosion hazards in face areas can result. • Fresh air flowing into the gob can create an explosion hazard as the gas composition in the gob moves from fuel-rich inert to explosive, creating EGZs. • Ignition sources inside the gob can be frictional ignitions or spontaneous combustion. • Bleeder ventilated gobs are surrounded on all sides by an EGZ that forms along the fringe areas between the fresh-air ventilated bleeder entries and the methane-rich interior of the gob. It is suspected that diffusion flames can propagate rapidly along these EGZ fringes if an ignition occurs"

Jan 1, 2015

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By S. O. Ogden

As most of you have probably surmised from the title of my paper, I am here today to talk with you about the use of diesel engines in the American mining industry and whether or not the free choice to use such equipment will continue to be available to mine operators. Of course, I will present to you my prepared remarks, however, these remarks may be essentially academic in light of a news release, parts of which I would like to read to you. Washington, D. C., The Department of Health, Education, and Welfare today announced proposed new regulations to reduce occupational health risks to workers in the U. S. mining industries by requiring the removal of all diesel powered equipment from American mines by December 31st "While we do not have complete and conclusive information to quantify these health risks we feel it is prudent to undertake this restriction on the use of diesel powered equipment without waiting for the completion of studies that are currently underway to identify and quantify these health risks," said a Department spokesman. HEW has been concerned about the health risks of diesel emissions in the underground coal mines for some time and have investigations underway designed to conclusively demonstrate the nature and magnitude of any health risks. However, HEW has decided to proceed with these regulations without waiting for the final results of these investigations. Further, HEW feels there is sufficient probability that diesel health risks do exist in all mining applications and consequently, the proposed regulations will apply to all surface and underground mining operations. It goes on a little further and indicates that due to the necessity of finalizing these regulations without delay, a period of fifteen days has been provided to receive comments regarding these proposed regulations.

Jan 1, 1978

By Robert B. Scott

Acid mine drainage, discharging from coal beds, has polluted our streams and rivers since early time. These pollutants affect water quality by lowering the pH, reducing natural alkalinity, increasing total hardness, and adding undesirable amounts of iron, manganese, aluminum and sulfates, The tangible damages are the costs involved in replacing equipment corroded by the acid water, additional treatment costs at municipal and industrial water treatment plants, and damages resulting from corrosion of steel culverts, bridge piers, locks, boat hulls, steel barges, pumps, and condensers. Intangible damages, which are real and important, include destruction of biological life of the stream, reduced property values, and streams rendered undesirable for recreational uses.1 The major problems of mine drainage occur in the anthracite and bituminous coal regions in Appalachia. However, many of the western mining states have significant mine drainage problems in specific areas, but the overall problem is not as great as in the eastern states.

Jan 1, 1970

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995

By Arvid E. Anderson

The paper describes the unique operating features of the Lebanon Concentrator Plant wherein both magnetic concentration and froth flotation are used. Chalcopyrite is selectively floated by the use of dual collectors, Aerofloats and secondary butyl xanthate. Both potassium ethyl xanthate and sodium isopropyl xanthate (dual collectors) are dissolved and emulsified with pine oil for the flotation of the pyrite. Sketches describing the plant operations are presented and plant operating metallurgical results obtained are also given. The optimum production of minerals by the froth flotation process is normally achieved [ ] smooth operating conditions, The process, because of its many variables, becomes an art as well as a science. Therefore, any phase of the operation which will aid the operator in his control of the numerous variables will help produce a smoother operating plant, One of the most important variables which the operator deals with is the addition of reagents, These are usually costly items and should be used discretely with minimum amount of waste, The danger is that ,this emphasis may reduce the reagent amount to a point below that required, or, on the other hand an excessive amount is added, Both conditions usually yield poor results. The drea of the metallurgist is to provide the operator with the tools enabling him to produce a good mineralized froth at all times. Normally the operator has no control concerning the type of reagents which he must use. This has usually been worked out for him in the laboratory and by plant-scale tests. He does have limited authority to control the amounts of the reagents at his disposal. This, I believe, is as it should be. However, the operator should be provided with the best combination of reagents for his particular job. The providing of this combination of reagents for his particular job, The providing of this combination is often difficult, yet it is very important in order to yield good results, With this in mind, the dual collector idea was introduced for the selective flotation of chalcopyrite, and also later for the flotation of pyrite at the Concentrator Plant of the Bethlehem Cornwall Corporation in Lebanon, Pennsylvania, Supplying several types of collectors has given the operator an additional effective tool, even though great variations are encountered in ore tonnage treated and in ore composition, This paper deals with the use of the dual collectors and with the addition of the reagents in the form of a pine oil emulsion, or more accurately, a pine oil suspension. It is hoped that other operators may find the ideas helpful. There does not seem, to me, to be definite scientific fact which would substantiate the necessity for the use of dual collectors. However, in actual operations, the metallurgical results at Lebanon became more uniform with the use of dual collectors, I look upon it as an "insurance policy" which greatly aids the operator during those periods when he is having trouble, One theory has been advanced, i.e. one collector has a greater tendency to float the coarser minerals, whereas the other one may float the finer ones. Consequently, a combination of the two collectors will result in optimum recoveries, There has been some evidence that this is true, but it is not conclusive, on the other hand, the use of a xanthate-pine oil suspension (or emulsion) should speed up the surface reaction of the collector with the sulfide minerals, result¬ing in more uniform flotation, This has definitely happened in our particular case. A more interesting unexplainable observation has also occurred; i.e., the xanthate solution does not appear to lose its strength as rapidly when it is in the form of an emulsion (or suspension), This was first observed when a 50 gallon drum of a 20% ethyl xanthate solution was taken to Wilmington, Delaware, for a laboratory test, using a homogenizer to produce the xanthate-pine oil emulsion. Upon arrival, the drum of xanthate had developed a considerable internal pressure, The relief of this pressure was accompanied by a strong odor, When the emulsion was returned to Lebanon for the plant test orders were issued to release the pressure prior to emptying the emulsion. Nopressure had developed within the drum and there was no unusual odor present, Since this time it has been observed that xanthate pine oil suspensions have greatly decreased the possible decomposition of the xanthate solutions. In fact, suspensions have been exposed for more than a month without apparently effecting their reactions in the flotation plant. On the other hand, we found that the regularly mixed concentrated xanthate solutions, after standing for several days, did not give the same results as the freshly made ones. This effect was greatly reduced by the use of xanthate pine oil suspension (or emulsion)

Jan 1, 1958

By S. K. Kawatra

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20Y. if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1990

By Richard G. Almes

Since the failure of a major coal refuse disposal embankment and impoundment in the Buffalo Creek watershed near Man, West Virginia in early 1972, there have been extensive changes in the design and construction requirements for coal refuse disposal facilities located throughout the United States. The primary emphasis has been on improving the safety of these facilities, particularly for impoundments which are capable of storing millions of gallons of process water and storm runoff. The Mine Safety and Health Administration (MSHA) of the U.S. Department of Labor (formerly the Mining Enforcement and Safety Administration, U.S. Department of interior) has been the lead federal agency in promulgating regulations pertaining to coal waste disposal. In 1974 and 1975, studies were undertaken by our firm under contract to the Mining Enforcement and Safety Administration to prepare a comprehensive engineering and design manual to be used by operators and engineers in the planning and design of coal refuse disposal facilities with the intent ion of avoiding any more Buffalo Creek failures. The resultant 800-page document addresses major subjects such as safety, environmental controls, and cost. Specific topics include characterization of coal refuse, classification of disposal facilities, project planning, geotechnical investigations, testing and design requirements, hydraulic and hydrologic design, environmental factors, operations, and monitoring, instrumentation, and maintenance.

Jan 1, 1980

By Joseph Githiria, Khadija Omar Said

Mineable material is defined using cut-off grade either as geological or economic cut-off grade. Both geological and economic cut-off grade affects the output generated in an open-pit mining operation. It distinguishes the amount of ore sent to the mill for processing and waste to the dump. This consequently affects the overall profits generated from the operation hence the need for cut-off grade optimization. There are several mining parameters that are considered in a typical cut-off grade model. They include economic, geological, and operational parameters. They have a significant effect to influence the cut-off grade selected in mining operations at any given period. Some of the parameters are stochastic in nature by having a random probability distribution that may not be predicted precisely. When selecting cut-off grades in a mine operation, the mining engineers must consider the dynamic nature of the operational parameters in order to maximize the net present value of the project. Modifying Lane’s cut-off grade model which was developed in 1964 to incorporate the stochastic parameters in the approach helps improve the net present value as shown in the paper. The modified Lane’s approach is developed into a stochastic computer-aided application code-named NPVMining. Using NPVMining, selected stochastic parameters are considered in this exercise to show the effect on the output (net present value). The selected parameters (price and grade-tonnage) are varied by ± 10%. NPVMining has a graphical user interface that makes it easy to use and displays results in a user-friendly way. It gives the user the choice to manipulate the data depending on the study being undertaken or any other factor affecting the specific mine. This paper analyses the effect of each of the selected mining parameters on cut-off grade using NPVMining to show the significance of monitoring their variance.

Jun 25, 2023