Search Documents

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By Patrick J. Foster

This paper summarises a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialled at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

By E. Emami, J. Valencia, J. Sattarvand

The knowledge of the final location of a drillhole is critical in obtaining the expected blasting results. This paper proposes a new methodology to control the drilling accuracy in open-pit mines using aerial images and machine learning. Specifically, it investigates how support vector machines (SVM) and convolutional neural networks (CNN) are useful for automatically detecting blastholes over drone images captured in blasting patterns. Several datasets were obtained from different mines in Nevada (USA) and were used to train and test models. We then processed those images to create orthomosaic and digital elevation representations of the patterns. Thousands of patches were then extracted and augmented to develop SVM and CNN models. The results demonstrate that machine learning is useful for drillhole detection and, in this way, to control the drilling accuracy and use the explosive energy more efficiently.

Sep 1, 2021

By J. M. McKinley

Mineral exploration programmes around the world use data from remote sensing, geophysics, and direct sampling. On a regional scale, the combination of airborne geophysics and ground-based geochemical sampling can aid geological mapping and mineral exploration. Since airborne geophysical and traditional soil-sampling data are generated at different spatial resolutions, they are not immediately comparable due to their different sampling density. Several geostatistical techniques, including indicator cokriging and collocated cokriging, can be used to integrate different types of data into a geostatistical model. However, with increasing numbers of variables the inference of the crosscovariance model required for cokriging can be demanding in terms of effort and computational time. In this paper a Gaussian-based Bayesian updating approach is applied to integrate airborne radiometric data and ground-sampled geochemical soil data to maximize information generated from the soil survey, enabling more accurate geological interpretation for the exploration and development of natural resources. The Bayesian updating technique decomposes the collocated estimate into two models: prior and likelihood models. The prior model is built from primary information and the likelihood model is built from secondary information. The prior model is then updated with the likelihood model to build the final model. The approach allows multiple secondary variables to be simultaneously integrated into the mapping of the primary variable. The Bayesian updating approach is demonstrated using a case study from Northern Ireland. The geostatistical technique was used to improve the resolution of soil geochemistry, at a density of one sample per 2 km2, by integrating more closely measured airborne geophysical data from the GSNI Tellus Survey, measured over a footprint of 65 x 200 m. The directly measured geochemistry data were considered as primary data and the airborne radiometric data were used as secondary data. The approach produced more detailed updated maps and in particular enhanced information on the mapped distributions of zinc, copper, and lead. The enhanced delineation of an elongated northwest/southeast trending zone in the updated maps strengthened the potential for discovering stratabound base metal deposits..

Jan 1, 2014

By J. -P. Tshibangu, A. Vervoort, A. Lavrov

Abstract: The aim of the research presented is to study the effect of complex loading schemes on the fracturing process during loading and/or unloading. A first set of experiments was done using a poly-axial cell. These experiments in combination with numerical simulations showed a difference in micro-fracturing (shear and tensile cracks), but not in macro-failure between various loading/ unloading schemes. The second set of experiments was based on the three-point bending test and several cycles with or without rotation between cycles were applied. If the specimen was rotated by 90° or 180° about its long axis between the first and second cycle, no Kaiser effect was observed. Résumé: Le but de la recherche présentée est d’étudier l’effet de schémas de charge complexe sur le processus de fracturation durant la phase de charge et de décharge. Une première série d’expériences était réalisée utilisant une cellule polyaxiale. Ces expériences combinées avec des simulations numériques ont montré une différence de micro-fracturation (fissures de cisaillements et de traction) pour les différents schémas de charge et décharge, mais en ce qui concerne la macro-fracturation ce n’est pas le cas. La deuxième série d’expériences était basée sur des essais de flexion trois points avec plusieurs cycles, avec ou sans rotation entre les cycles. Si l’échantillon est tourné de 90° ou 180° selon le grand axe entre le premier et le second cycle, l’effet Kaiser n’est pas observé. Zusammenfassung: Der Zweck der vorliegenden Forschung bestand darin, den Einfluß von komplizierten Beanspruchungsschemen auf den Bruchprozess im Laufe von Belastung und/oder Entlastung von Gesteinen zu untersuchen. Der erste hier beschriebene Satz von Experimenten wurde mit einer dreiaxialen Belastungsmaschine angestellt. Diese Experimenten zusammen mit dazugehörigen numerischen Simulationen zeigten Unterschiede zwischen Be- und Entlastungsbeanspruchungen in Bezug auf mikrobruchmechanische Mechanismen (d.h. Scher- oder Zugrisse) an, aber nicht in Bezug auf den Makrobruchprozess. Der zweite Satz von Experimenten umfasste Gesteinsbeanspruchung in mehreren Zyklen von Drei-Punkt-Biegung, indem die Gesteinsproben zwischen den Zyklen um einen angegebenen Winkel (0°, 90° oder 180°) gedreht wurden. Falls die Probe um 90° oder 180° gedreht wurde, wurde kein Kaiser-Effekt im zweiten Zyklus beobachtet.

Jan 1, 2003

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By F. M. G. Egerton

Mechanisation of mining operations is not a new concept in the world of mining. Machinery has been developed, manufactured and used for many decades in massive orebodies and coal mines, both locally and abroad. Because of their size and the huge tonnages available, massive ore bodies lend themselves very easily to mechanisation. However, little progress in mechanisation has been made in narrow tabular orebodies in South Africa. The equipment available for narrow tabular orebodies requires excavations of a size that introduce large volumes of waste dilution. Nevertheless, it is essential for South African miners to experiment with mechanisation and to find a solution to the problem. This address looks at current conventional mining methods and compares them to bord-and-pillar type mining methods. Off-reef mechanisation is also touched on. It then looks at different hybridised mining methods that are being used, i.e. a mixture of conventional mining and mechanisation. It finally looks at future prospects for mechanisation in narrow tabular orebodies.

Jan 1, 2004

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By J. Whitford

The established crown pillar extraction method at Gold Fields Australia Ltd.’s Crusader Mine, leads to the significant dilution and poor recovery of ore due to caving of the overlying loose rockfill. The application of selectively injecting specifically developed ‘FB200’ ettringite (calcium sulphoaluminate hydrate) type cement grout into loose rockfill to form a stabilised rockfill material, enables an artificial crown pillar to stabilise the surrounding rock mass and prevent caving of the overlying loose rockfill during crown pillar extraction. Investigation of the geomechanical criteria for crown pillar extraction beneath stabilised rockfill has enabled the safe and efficient extraction of two crown pillars at the Crusader Mine. La méthode actuelle d'extraction des piliers horizontaux à la mine Crusader dont la propriétaire est le Goldfields Australia Ltd amène à une dilution sensible du minerai, à cause de l'effondrement du remblai peu compacté qui se trouve au-dessus. Par moyen d'injection sélective du coulis de ciment FB200 ettringite (sulfoaluminate de calcium hydraté) qui a été développé spécifiquement pour cette application, un pilier artificiel est crée et celui-ci empêche l'effondrement du remblai pendant l'extraction du pilier de minerai au-dessous. A la suite des études géotechniques de la méthode, deux piliers horizontaux à la mine Crusader ont été extraites, de manière efficace et sûr. Die feststehende Krone Pfeiler Extraktionsmethode beim Crusader Mine von Gold Fields Australien GmbH, führt wegen caving des overlying lockerer rockfill zur bedeutungsvollen Verdünnung und schlechtem Wiederfinden des Erzes. Der Antrag, ausdrücklich entwickelten 'FB200' ettringite selektiv zu spritzen, (Kalzium-sulphoaluminate-Hydrat) Art kittet Mörtelschlamm in lockeren rockfill, um ein stabilisiertes rockfill-Material zu bilden, ermöglicht einem künstlichen Kronenpfeiler, die umliegende Steinmasse zu stabilisieren und caving des overlying während des Kronenpfeilerherausziehens lockeren rockfill zu verhindern. Untersuchung der geomechanical-Kriterien für Kronenpfeilerherausziehen unter stabilisiertem rockfill hat dem sicheren und tüchtigen Herausziehen von zwei Kronenpfeilern beim Crusader Mine ermöglicht.

Jan 1, 2003

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By I. Matsunaga, K. Aoki, W. -j. Jung

Blasting is widely used in mining and basic construction because of its speed and economy to destroy the rocks. Blasting has the advantages of reduced excavation costs and shorted construction time when compared to the use of heavy machinery for excavation and cutting such as that with a tunnel boring machine. There are numerous problems with blasting, including the noise, vibration and fly rock. So it is necessary to accurately evaluate fracture mechanics of rocks on the dynamic loading condition to control the fracture process of the blasting. The tests using Hopkinson's effect for the dynamic condition using the precise detonators were performed for various strain rates on three different kinds of rocks. In the tests using Hopkinson's effect for the dynamic condition, the high-speed camera was used to observe the fracture process of the test sample rocks. As the results of experiments there was an increase in the tensile strength of rock with an increase in the strain rate for three kinds of rock on the dynamic loading. The tensile strength of rocks with high porosity on the water saturation condition was decreased on the both static and dynamic condition. It is clear that the strain rate and water saturation were influenced to the tensile strength of the rocks.

Jan 1, 2003

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

This paper presents an initial investigation into the viability of co-kriging the grades of multiple mining cuts in a two dimensional, thin reef scenario. Deposits with gradational mineralized zones, in the perpendicular sense, are not as well served by the use of reef accumulation and thickness as deposits characterized by a sharp distinction between ore and waste rock. South African Bushveld Complex platinum deposits and Witwatersrand gold deposits are examples of this distinction. The calculation of an optimal mining cut is of paramount importance in the mining of Bushveld platinum. Two-dimensional kriging of a constant stoping width mining cut is an effective method for resource calculations once a cut is decided, but this begs the question of how to decide on the cut. Comparison of multiple cuts is used as a way of achieving this decision on many of Anglo Platinum’s operations. Although the kriging of each cut is valid in isolation, occasional negative values occur when incremental grades between overlapping cuts are calculated. Negative incremental grades cannot reflect reality. They are thought to be related to the inability of the method to include the strong continuity in the perpendicular direction demonstrated by the relevant variograms. Co-kriging of related variables has been investigated as a potential means tore impose this inherent order relationship. Various co-kriging options have been investigated. The method has been tested on a real data set from an established platinum operation. One of three types of anomaly has been investigated so far. The results show that co-kriging the mining cut grade as the primary variable, with just one secondary variable, the reef thickness, eliminates most occurrences. Severe anomalies remaining are arguably indicative of population mixing and might be more effectively treated by rezoning the data. Aim—To investigate the viability of co-kriging the grades of multiple mining cuts as a method for resolving anomalies in the estimation of such cuts on Bushveld platinum deposits, with applicability to other thin reef type deposits with a gradational not sharp cut-off between ore and waste in the direction perpendicular to the reef. Keywords: co-kriging, cross variograms, ordinary kriging, platinum, two-dimensional, grade profile

Jan 1, 2003

By B. S. Xakalashe

Keywords: Pyrometallurgy, silicon, solar cells Silicon has been the dominant material in the photovoltaic (PV) industry since its application in the space industry in 1958. This review focuses on crystalline silicon solar cells, primarily due to their dominance in the photovoltaic industry, omitting other photovoltaic cell technologies such as second generation (e.g. thin films) and third generation (e.g. nano-structured solar cells). The value chain for the production of crystalline silicon solar cells has been reviewed. The primary processing steps for the production of silicon solar cells from quartz are as follows: bulk production of metallurgical-grade silicon via carbothermic reduction in a submerged furnace, refining of metallurgical-grade silicon via the chemical means to polycrystalline silicon, or through the metallurgical route to solar-grade silicon, wafer manufacturing, and, lastly, silicon solar cell manufacturing. During downstream processing, solar cells are interconnected and encapsulated into solar modules (panels), which can be used individually or incorporated into a photovoltaic system for electricity generation and supply. The cost for crystalline silicon based solar cells is approaching one US dollar per watt peak ($1/Wp), while the most cost-effective solar modules in industry have reported costs below $1/Wp, and are based on CdTe thin films. Solar cell energy conversion efficiencies as high as 22% have been reported in industry for crystalline silicon solar cells.

Jan 1, 2011