Search Documents

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By T. Salman

Most authorities agree that the dissolution of gold from an ore takes place according to the Elsner equation first stated in 1846. The main requirements for the dissolution reaction to proceed are:(1) that the gold be clean.(2) that the gold be exposed to the solution.(3) that the cyanide solution be active, i.e., not over loaded with impurities which could retard or inhibit the reaction.(4) that an adequate supply of oxygen be available (from air).When the above conditions are met, cyanidation becomes basically a mechanical operation.Minerals such as quartz, calcium carbonate are relatively inert to cyanide though they may give rise to mechanical troubles. Most ores present an assortment of chemical problems, depending upon the constituent present, which react to the solution to varying degrees. It should be borne in mind that minerals which are disturbing to the operation, though present in small amounts, usually exceed the weight of the gold by several hundred times. In addition, the application of flotation and other forms of concentration to gold ores, previous to cyanidation, concentrates not only the gold, but also the other heavy minerals and these complicate the chemistry of the process.

Jan 1, 1975

By Ken Wood

"A reliable source of water of an acceptable quality is vital to the success of any mineral processing plant using wet methods. For Cerro Verde, a new 108,000 t/d copper mill in southern Peru, the main source of raw water is the Chili River. The Chili River is heavily contaminated with raw sewage, industrial wastewater and agricultural runoff, and can also receive high sediment loads during the rainy season. The initial water treatment plant could not supply design flows of water due to the exceptionally poor water quality. Problems with treated water quality caused significant difficulties with water consuming equipment, such as the plant cooling systems. This paper details the Cerro Verde water system and changes from design through to start up from a mineral processing perspective.INTRODUCTIONMining, and mineral processing in particular, is a water intensive activity. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry. This case study forms a basis for ongoing research into water use and reuse at mines and mineral process plants, conducted by AJ Gunson, under the supervision of Dr. Bern Klein and Dr. Marcello Veiga at the University of British Columbia. The case study material was gathered through involvement with the design, startup, and redesign of the Cerro Verde water system.Cerro Verde is a low-grade copper porphyry mine, located near the city of Arequipa in southern Peru, at an elevation approaching 2,800 m. In 1972, one of the world’s first copper Solvent Extraction – Electrowinning (SX/EW) facilities was built on the site, processing oxide ore from two main open pits. In 2004, the operator, Sociedad Minera Cerro Verde S.A.A. (SMCV), approved a 108,000 t/d expansion project to process sulfide ore reserves through a new concentrator plant. The plant was designed under extremely tight schedule and capital constraints, with a mandate to intentionally avoid any overdesign."

Jan 1, 2008

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By A. Lee Barrett

"THE COAL INDUSTRY of the United States• and Canada has made great progress in recent years. Coal mining in •the old days represented one of the most arduous tasks for labour and industry, but over the years great progress has been made in reducing the effort required from labour. Also, the tonnage produced per man, the cost of the coal per ton, and the overall safety of the operation, have been greatly improved.Looking back over the past fifty years:, the era can be divided into four principal parts: (a) hand-loading, (b) track mining methods, (c) off-track mining methods, and (d) continuous mining. For many years, all of the coal was won by hand-mining methods. The first forms of mechanization •resembled the move from the horse •and buggy to the automobile. Early track mechanical mining methods were usually adaptations of the direct methods involved in hand-mining, with each improvement directed toward some specific process. A revolutionary development came about with off-track mining methods. The first efforts in this direction were provided by off-track mechanical loading machines, which loaded the cars •on track and differed from conventional track mining methods only in that the loading machines themselves operated on the mine floor. With the advent -of the shuttle car about ten years ago, true off-track mining came into being, and real progress in this direction began to be made.At the present time we •are at the beginning of a new era -.the era of continuous mining. There will be a period of development with some time needed before the system is generally applied throughout the industry, but -already enough •has been done to indicate rather dearly what the future holds in this direction."

Jan 1, 1953

By Stephen L. Chryssoulis, Stamen Dimov

"Preg-robbing has been known for many years, where increased losses are suffered because dissolved gold is removed from solution by adsorption onto carbonaceous matter. In direct cyanidation circuits it is reasonable to conclude that the preg-robbed gold is either in a gold cyanide [Au(CN) - 2, AuCN] or metallic [Au°] form. However, in circuits with a pre-oxidation step possibilities increase and multiply even further because of water recycle streams containing apparent and not-so-apparent gold ligands. It is in these circuits where speciation of sorbed gold, i.e. the identification of the gold compound, is useful. The importance arises from the fact that proper identification of the sorbed gold species can be used to determine how, when, where and why gold was removed from solution, thereby identifying the exact cause of the problem and providing clues as to how it may be rectified.INTRODUCTIONTo the best of our knowledge, this is the first attempt ever to speciate gold preg-robbed by carbonaceous matter using a surface sensitive microbeam technique. This approach enables the direct determination of gold species sorbed on carbonaceous particulates, opening an entirely new field in the understanding of the chemistry of gold sorption on carbon. The reasoning behind this effort was to add to the current knowledge of the detrimental effect chloride ions have on gold recovery by the pressure oxidation and in particular why in the ensuing CIL step, gold is not being desorbed from the surface of the carbonaceous particles (Table 1)."

Jan 1, 2004

By L. Li, K. Jiang

China is the world largest producer and consumer of zinc. Beijing General Research Institute of Mining and Metallurgy (BGRIMM) is one of major research and engineering institutes for nonferrous metallurgy in China. This paper (presentation) introduces the development of China’s zinc smelting industry, key production processes and main producers. The process research and development are reviewed as well as BGRIMM’s R&D activities in the last decade. China's refined zinc production was 4,829kt in 2012, accounting for 38.6% of world production. Primary production was 4,722kt. There are around 150 refined zinc producers in China. The traditional fluid bed roasting - leaching jarosite is still a dominant process for primary production and its production accounts for about 60% of country's total production. However, the direct leaching process is gaining market share. Seven direct leaching plants with 330kt/a capacity, including autoclave leaching and the Outotec direct leaching, have been put into production by June 2013. Five autoclave leaching projects with 590kt/a capacity are in the pipe line and are expected to be commissioned in 2014 and 2015. To cut the production cost and improve smelter economics, process research to optimize the production flow sheet, to improve the iron removal and to enhance the recovery of co-existed rare metals were carried out. The development trends of China’s zinc smelting industry from the view of cutting production cost, improving energy efficiency, increasing comprehensive utilization are discussed accordingly.

Jan 1, 2014

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005

By Hua-Zhong Yu

Gold is one of the most widely used substrate materials for self-assembly. Self-assembled monolayers (SAMs) prepared from alkanethiols and their derivatives on gold are the most reliable and well-studied systems to date, which have attracted much attention because of interest in two-dimensional molecular assemblies, and of their potential applications in molecular devices, sensors, and functionalized interfaces. Gold electrodes are also very important in microelectronics and electroanalytical chemistry. This work reports the characterization of a new type of gold substrates for self-assembly. The gold substrates are constructed from recordable compact disks (R-CDs) with simple and straightforward wet-chemical treatment, and can be made at desired sizes and shapes that satisfy different experimental needs. In particular, an easy, inexpensive, and reproducible method to prepare self-assembled monolayers (SAMs) on CD-R gold substrates after removing the protective polymer films with concentrated nitric acid was described.

Oct 1, 2003

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By J. W. Austin

"Introduction The Brenda dust collection system was originally designed to handle air at the 5000 ft. elevation with less than 1 grain of dust per cubic feet of air handled. The temperature variation is from 32°C in the summer to -20°C in the winter.DUST COLLECTIONOriginal Equipment 1. Primary Crusher 2 compartment baghouse, shaker type design capacity - 17,000 cfm2. Primary Screening 3 compartment baghouse, shaker type design capacity - 30,000 cfm3. Secondary Crusher 4 compartment baghouse, shaker type design capacity - 45,000 cfm4. Secondary Screening 4 compartment baghouse, shaker typedesign capacity - 60,000 cfmThe original dust collecting equipment was designed using a napped terylene fabric at an air to cloth ratio of 5:1. The ducting was designed to handle the dust laden air at 3200 ft. per minute with all elbows and blast gate sections rubber lined. The hoods and the pickup velocities were designed to handle the anticipated low dust counts."

Jan 1, 1976

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By Norman O. Lotter

Drill core is preferred as the sample material for metallurgical and mineralogical characterisation and flowsheeting of an orebody. The question arises as to how to do this at the economic optimum, since geologists have several other strategic uses for their drill core. The limiting factors are the cost of extra drilling for the metallurgical testwork and the need to preserve the drill core record. In this study, the representative sampling of drill core at an economic optimum for metallurgical testing is addressed. This phase of the drill core work is preceded by earlier drill core characterisation - for which other appropriate sampling protocols are used - that has provisionally categorised the orebody into geometallurgical units. In stratified sampling of drill core, use is made of a version of the stratified approach to compound distributions proposed by Cochran in 1946. Use is made of Gy’s 50-piece minimum sample mass model to estimate minimum requisite sample mass. In the case where sampling and testwork are required on a Lifeof- Mine blend of a given ore deposit, whereby defined ore types or geometallurgical units are present, the sample mass requirement is significantly reduced by working from drill-core at the geometallurgical unit level. A case study using Raglan drill core is discussed. Using nickel as an indicator paymetal, and sampling at a fundamental variance level of 8%, the minimum sample masses for disseminated sulphides, net-textured sulphides, and massive sulphides are 3.80, 7.37 and 4.39 kg respectively. When the same drill-core is sampled as a Life-of-Mine mixture without knowledge of the geometallurgical units, the minimum sample mass increases to 84.28 kg. It is thus possible to assemble a representative Life-of-Mine sample of drill-core more economically, at the same time validating its representativity. Equivalent calculations for copper, platinum and palladium are discussed, with outcomes consistent with this finding. When all four paymetals are considered, one selects the largest minimum mass out of all four cases. This results in minimum sample masses of 11.67, 74.90 and 175.16 kg for disseminated sulphides, net-textured sulphides and massive sulphides respectively. The simulated Life-of- Mine blend would require a minimum sample mass of 377.33 kg to cover all four paymetals.

Jan 1, 2010

By D. M. Doyle

"A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc. over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study 11rogresses through monthly, daily and finally, into quarter hourly data, the variations become more evident and most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program.The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Sudbury Operations, the material and control equipment, the commitment, the new energy accounting practices and lastly, the policies. Examples of successful energy conservation endeavors include automatic peal electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailmen: of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and if necessary, immediate reporting of energy and energy per unit of production information. The program so reported at Falconbridge’s Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0 million dollar annual energy account."

Jan 1, 1979

By Jochen Franke, Derek D. Lichti

"This paper gives a brief introduction and presents recent enhancements in the MillMapper technology developed for thickness gauging and condition monitoring of liners in grinding mills used for mineral comminution. It also introduces the recent expansion of MillMapper functionality aimed at mill operational optimization. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces at feed, shell, and discharge ends with millimeter accuracy. Data capture takes nominally 5 minutes, hence interruption to mill operation is negligible.The paper is structured as follows. First, a review of the technology and discussion of recentlyimplemented innovations such as liner change out forecasting, automatic ball charge volume and weight measurement, and automatic mill liner volume/weight measurement for mill operational control or load cell calibration are presented. Combined weight information provides control over load related issues such as load fill levels for relining, or start-up load after reline. Feature descriptions are followed by a listing of the numerous advantages over existing techniques and the benefits to operations. Results from the application of MillMapper are presented throughout.INTRODUCTIONThe need for thickness gauging of liners of grinding mills used for mineral comminution is well known but the task is rarely completed to a satisfactory standard. Liner failure resulting from excessive wear can have expensive consequences. Furthermore, mill performance as well as liner wear are known to be correlated to lifter bar geometry (Napier-Munn et al., 1999; Rajamanni et al., 2005). At present, the following techniques are routinely used to gauge the thickness of mill liners:1. Visual inspection;2. Ultrasonic thickness gauging (for steel liners); and3. Physical inspection (e.g. nail inserted in rubber liners)"

Jan 1, 2008

By Thorndycraftm R. B.

"PURPOSEThe purpose of this presentation to the Canadian Mineral Processors is to review gold heap leaching systems currently in use and discuss their applicability to Canadian ores. The author's experience with the development and operation of heap leaching spans the past four years at. Pinson, and visits to many ether heap leaches in the western United States.INTRODUCTIONBy way of introduction to the heap leaching system, I will describe in slight detail the method used at Pinson Mining in northern Nevada. This will be followed by a discussion of optional methods in use at other operations visited.The Pinson orebody is a finely disseminated, well-oxidized hydrothermal deposit. Gold particles are finer than 20- microns. The orezone hostrocks are metamorphosed and silici¬fied limestone and shale. Sulfides and carbonaceous materials are negligible.The Pinson open-pit mine has operated since June 1980. It produces 1500 tpd of C.I.P. mill feed averaging .10 oz gold per ton, and 1500 tpd of heap leach material averaging .025 oz gold per ton. Cutoff grades are 0.04 for mill feed, and 0.01 for heap leaching. Stripping ratio is 9 tons of waste and leach grade to 1 ton of mill feed.The project is located in northern Nevada at 4900 feet above sea level.,Winters are fairly severe, with freezing conditions affecting operations from early December through April. Although officially designated as ""high-mountain desert"" country, snow and/or freezing rain occur almost every week of the winter.To date, all Pinson production-scale heap leaching has treated run-90,000 tons of ore are stacked on 300 foot square clay leach pads. Cyanide leach solution is applied through ""wobbler"" sprinklers at .0025 gpm/sq ft for 60 to 90 days. The pregnant solution flows from the heap by gravity to plastic-lined ditches, into a collection sump and then through buried piping to the 2.2 million gallon pregnant solution pond."

Jan 1, 1984

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

By E. Goris Cervantes

"A theoretical framework based on a detailed analysis of mine operations data from an oil sands mine in northern Alberta and the static simulation of truck cycle times are developed, verified, and validated in this paper. Implementation of this framework provides better results than existing tools that rely solely on manufacturer data. This, therefore, aids in efficient equipment planning for the life of the mine. The use of this framework to modify existing productivity curve estimation methods currently in use at the mine site is also proposed. This method replaces “loaded flat haul” with “loaded effective flat haul” in the productivity estimation. Validation of the model results in a 4% overestimation of productivity, versus an underestimation of more than 10% when using the existing in-house method. ¦ KEYWORDS Equipment planning, Life-of-mine (LOM) planning, Oil sands, Productivity, Truck cycle times RÉSUMÉ Un cadre théorique fondé sur une analyse détaillée des données relatives aux activités minières d’une exploitation de sables bitumineux dans le nord de l’Alberta et la simulation statique des temps de cycle des camions sont développés, vérifiés et validés dans cet article. La mise en oeuvre de ce cadre offre de meilleurs résultats que ce que proposent les outils existants, lesquels se basent uniquement sur des données des constructeurs. Ceci contribue donc à une planification efficace de l’équipement pour des projets relatifs à la durée de vie de la mine. On propose également de se servir de ce cadre pour modifier les méthodes d’estimation de la courbe de productivité actuellement utilisées sur le site minier. Cette méthode remplace le concept de loaded flat haul (la distance parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) par celui d’effective loaded flat haul (la distance relative parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) dans l’estimation de la production. La validation du modèle résulte en une surestimation de 4 % de la productivité, par rapport à une sous-estimation de plus de 10 % avec la méthode actuellement utilisée en interne. ¦ MOTS CLÉS planification de la durée de vie de la mine, planification de l’équipement, productivité, sables bitumineux, temps de cycle d’un camionINTRODUCTION One aspect that differentiates oil sands mines in northern Alberta from conventional hard-rock mining is the environment in which they operate. Due to ground characteristics, producers in the region experience roads with very high rolling resistance (RR) that, in turn, negatively affect haul-truck performance and greatly increase fuel consumption and emissions. Oil sands mining companies use some of the largest haul trucks in the world. In addition, oil sands mines cover more extensive areas than hard-rock pits, resulting in longer haul distances on roads made of comparatively more viscous material."

Jan 1, 2019

By G. Taylor

"The Iron Ore Company Of Canada's Carol Project is located in Labrador City, Newfoundland. Labrador City is some 912 air kilometers northeast of Montreal, and 417 ratl kilometers north of Sept-Iles, Quebec.Over 2,800 employees work at the Carol Project to produce some 20.0 million tonnes of concentrate and 10.5 million tonnes of pellets annually.In 1979 our Training Department started to develop the DACUM System of training for our Concentrator Operations Department.DACUM is an individualized, self-learning, training program. It is both a curriculum plan and an evaluation instrument.To date, the DACUM System has been completed for all occupations in the concentrator and work will commence shortly to develop DACUM for our Pellet Plant and Mine Operations Departments."

Jan 1, 1982