Search Documents

By Tiago de Abreu Siqueira

CO2 geological storage is one of the current technologies developed worldwide to reduce industrial emissions of carbon dioxide to the atmosphere. Two main mineral types of deep geological reservoir could be contemplated for CO2 storage: sandstone reservoirs and carbonaceous reservoirs. Geochemical reactivity of a dolomite-calcite mineral compound and magnesite pure mineral was studied with a set of nine experiments per crushed mineral phase with two saline solution and with mQ water and three temperatures: 50°C, 90°C and 150°C. Experiments were performed in batch reactors with 250 bar of CO2 partial pressure during 24h to assess the effect of temperature and salinity in constant CO2 pressure. Solid characterization was performed by XRD and solution analysis by ICP-OES. Acidification of solutions due to CO2 dissolution in water is the main source of reactivity in the system. Proton concentration increases and causes partial dissolution of initial dolomite, calcite and magnesite and release of Ca2+ and Mg2+ cations in solution. Bicarbonate anion (HCO3) concentration also increases due to CO2 dissolution in water and carbonate minerals dissolution. Temperatures of 90°C and 150ºC increase the kinetic of reaction and the dissolution of minerals and cations release in solution. New carbonate crystalline phase precipitates as a Ca, Mg solid solution between dolomite and calcite pure poles.

Aug 8, 2018

The leaching characteristics of a number of Australian uranium ores were determined under acid and alkaline conditions. Ores from the Ranger, Nabarlek and Koongarra deposits in the Northern Territory were readily leached in dilute sulphuric acid. Suitable processing conditions were: leaching at 35-40°C, pH 1·52·0 and redox potential -475 mV for periods of 16-24h with ore ground to 50 per cent -200 mesh CB.S.S.). Ore from the Roxby Downs deposit in South Australia required leaching at 55°C and a redox potential of -650 mV to achieve a satisfactory recovery. All ores contained refractory minerals which were not leached under conventional conditions, limiting uranium extraction to 86-96 per cent.Carbonate leaching of carnotite in calcrete ores from Yeelirrie and Lake Way in Western Australia yielded uranium extractions of at least 98 per cent. Leaching rates were considerably faster than those reported for other applications of alkaline leaching as the slow oxidation step was not required.

Jan 1, 1979

By R. D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market. IntroductionMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. This paper will concentrate on market-based approaches to valuation of such properties. Other authors at MM2000 presented papers on cost and income approaches. Sorentino (2000) also provides a useful overview with some provacative commentary on methods.Market based-approaches are based on the principle of substitution and include such techniques as: comparable transaction analysis (sometimes referred to as sales comparison analysis); farm-in commitment (or option agreement) analysis; rules-of-thumb; and comparable market value analysis.Are there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2002

By W Dodson, S Dogramaci

Isotopes and hydrochemistry were used to define groundwater flow systems and better understand the hydrogeological setting of the Karijini National Park, which is in the Central Pilbara region adjacent to the Marandoo iron ore mine. Based on the stable isotope composition of the water samples, the data can be divided into two main groups. Groundwater is characterised by depleted dD and d18O, suggesting no significant evaporation effect. Surface water on the other hand is more enriched in dD and d18O due to evaporation. The relatively high concentration of Cl- compared to rainfall and depleted dD and d18O values of groundwater indicate that recharge of the aquifers is occurring during intense rainfall events when rapid infiltration occurs. Evapotranspiration then acts to concentrate ionic species prior to recharge. Relationships between the major ion concentration and catchment area, surficial Tertiary cover and distance between recharge and discharge were identified. The results show that these catchment variables combine to determine unique water chemistry for each sub catchment in Karijini National Park. The TDS concentration of the groundwater in the Marra Mamba Iron Formation that hosts the Marandoo ore body is higher than most of the water bodies surrounding the mining area suggesting significant modification or different recharge mechanisms to that of the Karijini groundwater.

Jan 1, 2009

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By P. F. Ledwaba

South Africa?s Northern Cape Province houses a variety of gemstone minerals. Diamonds remain the primary gemstone in the province, but there are also tiger?s eye, sugilite, rose quartz, jasper, amethyst, amazonite, tourmaline, and topaz deposits. This paper gives an overview of the tiger?s eye (TE) mining sector in the Northern Cape, with the objective of assessing the potential of TE to contribute to job creation and poverty alleviation in the province. Mining of TE started in 1803, but gained momentum during the 1960s. Mining is conducted on a small-scale basis, and in most cases without any legal framework. The majority of the residents are not benefiting from TE. It has been reported that an estimated R700 000 to R800 000 worth of TE is leaving the country every week through illegal trading. The potential for TE mining to contribute to socioeconomic development is hindered by illegal operations, lack of technical skills and knowledge, exploitation by dealers, lack of market information, community rivalries, and absence of value addition. A multi-stakeholder approach is needed to formalize the sector and reap the benefits. Mintek is spearheading a TE project in the Prieska area of the Northern Cape, which aims to establish a gemmological centre where TE can be beneficiated into saleable and high-value products..

Jan 1, 2014

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By M. Lonoff

G. Campbell The paper by M. Lonoff looks at the importance of byproduct prices on copper production. The paper develops several interesting points on this topic, but there are some points in the theoretical discussion that could use further development. A couple of these theoretical topics will be considered here using the paper's framework of assumptions without concern about how realistic the assumptions are for the copper industry. Lonoff's theoretical model is based on a static, homogenous world where all copper/byproduct deposits are identical, and these deposits are the main source of these metals. Due to the importance of the byproducts to the production decision, the term coproducts will be substituted for the term byproducts to reflect more accurately this condition. The conclusion is drawn that a rise in coproduct prices necessitates a decrease in copper prices because copper production is increased as a consequence of increased coproduct production. The observation that real world behavior does not always follow this pattern is dismissed as "speculation." However, it can be easily shown that within this simple framework market forces might create the observed behavior. The key question to be answered is what causes coproduct prices to rise. Three possible cases will be used as illustrations. The first case is the one implicity assumed by Lonoff. Here, the demand for coproducts increases at all prices (an outward parallel shift of the demand curve) with the demand for copper remaining constant. As reported in the paper, the results are higher coproduct prices, an increase in coproduct production, and lower copper prices due to the resulting increase in copper production. The second case is when the supply of coproducts are constrained-leading to higher market prices. Copper production, as required by the simple model, is also reduced which Reply by M. Lonoff Campbell's comments give me an opportunity to clarify a few points in "Copper and Its Byproducts." That paper examined the affect of byproducts on the copper market and considered the relative riskiness of multi-metal deposits from an investment standpoint. That brief note made no attempt to be exhaustive. Nevertheless, Campbell's comments miss the point of the paper and necessitate a response. My "theoretical model" was static and I freely conceded after introducing the assumption of identical deposits that "none of the assumptions hold." These simplifying assumptions allowed me to bound the possible effects of higher byproduct prices on the copper price by assuming identical deposits and computing average price effects. I took great pains to subsequently explain that since deposits are not identical the identity of the marginal deposit might change due to byproduct price changes. In this case, average price affects will overstate the affect of byproducts on copper prices. According to Campbell, I dismiss as speculation any "real world behavior that does not always follow this pattern" (of metals prices moving in opposite directions). In the byproducts paper I noted that gold, copper, and silver price movements often parallel each other on an intra-day or day-to-day basis. Such movements are largely due to market anticipation of or reaction to changes in interest rates that affect carrying costs of metals stocks. Other movements may be due to anticipated changes in available supply or physical requirements. I loosely grouped these effects as speculative. To distinguish this statement from the main thrust of the paper, I contined "In the long run if gold and silver prices remain high the equilibrium copper price will be lower." The paper set out long run equilibrium conditions rather than attempting to explain price movements on a daily basis or on a year-to-year basis.

Jan 11, 1983

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By E. Naesgaard, Brian E. Hall, A. Amini, Advanced Geosolutions, A. Azizian

"A 2 km section of the Evergreen Line Rapid Transit Project is supported on improved ground consisting of cement deep soil mix (CDSM) panels because of highly variable and challenging soil conditions, especially the potential for seismic liquefaction-induced lateral spreading. CDSM was used as an alternative approach in place of driven piles for reducing the seismic lateral spreading displacements. An additional significant aspect of obtaining owner acceptance for CDSM was demonstrating that both seismic and non-seismic performance would equal or exceed that of using driven piles. It was recognized that, to demonstrate adherence to the seismic performance requirements, seismic design should be based on dynamic analyses (using FLAC) to estimate likely displacements and stresses/strains in the CDSM panels. One focus of the analyses was investigating the potential for cracking of the CDSM panels and the resulting displacements. This was simulated using the Ubiquitous-Joint and UBCSAND constitutive models.INTRODUCTIONThe Evergreen Line Rapid Transit Project (ELRT) is an 11 km extension of the SkyTrain system through Burnaby, Coquitlam and Port Moody in the Lower Mainland of British Columbia, Canada (Figure 1). The ELRT project is being delivered through a Design/Build/Finance model by Evergreen Rapid Transit Construction (EGRT), an SNC-Lavalin Inc. company, to the Province of British Columbia (the Province).This paper discusses the ground improvement design for a 2 km section of the alignment through Port Moody, a historic city at the head of Burrard Inlet. The alignment is located in a right-of-way of restricted width with many pinch points close to residential and commercial properties, and directly adjacent to the Canadian Pacific Railway (CPR) mainline tracks. The ground slopes from south to north across the alignment towards Burrard Inlet at inclinations of up to about 6%. Design and construction of the Port Moody section was subcontracted to SNC-Lavalin Constructors (Western) Inc. (SLCW) and SNCLavalin/ Graham Construction Joint Venture (SGJV). Construction included single- and double-track slab guideways, pocket track (where up to four to six tracks were present), and Moody Centre Station."

Jan 1, 2015

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By Enrique Fernandez

M-30, Madrid’s inner ring, covers 42 sq km of the city centre where one million people reside. It was constructed in several phases during the sixties and the eighties. The design criteria applied to those phases were different and were not always homogeneous with urban roads with lighting regulation as well as speedways. These areas had a heavy concentration of access and exits and there had been made many changes on the number of traffic lanes which has caused heavy traffic congestions and high accident rates. The environmental impact and noise pollution in residential areas are also consequences of M-30. The Madrid Major took a decision at the beginning of the present legislation, based on socio economic and environmental evaluation; rebuild the M-30 with the following sustainable mobility principles: Underground transfer of a considerable portion of the main ring and some of its links replacing some parts of the surface with new green areas in order to reduce the environmental impact. Increase the traffic capacity, improving the traffic continuity and fluidity and eliminating the lighting regulation areas, which is one of the main congestion problems currently. Increase the traffic safety with clear signalling information panels and avoiding difficult maneuvering. Redesign the links with the high capacity radial highways and other connecting lanes of the city. The project is worth 3.7 billion Euros. In 2007, when the construction is completed, it is expected will save 14 million of journey hours that represent 4.5 million Euros saved in fuel consumption per annum, There will be a very significant reduction of 35,000 tons of CO2 in terms of pollution and 400 less car accidents. Those values will increase even more in the following years. The areas beside Manzanares River, running parallel to the M-30 on the western side of Madrid, will be highly enhanced. Better water quality and the recovering of the green areas existing in old times will also return for the citizen’s enjoyment. TUNNEL CROSS SECTION OF CALLE 30 SOUTH BY PASS One of the major challenges of the new Calle 30 is actually not only the related to the main road but also to the link with the A-3, with highway to Valencia. This link is currently the most congested area and has one of the highest traffic densities of Spanish roads, with more than 250,000 vehicles/day. The remodelling of this area is the principle objective of the South by-pass. The tunnel is the only answer for this by-pass as the road alignment will go among buildings. A twin tube design, one for each direction, with three lanes allowing the circulation of both, light cars and heavy trucks, is the solution that has been

Jan 1, 2007

By Ralphie Adams, Tiana Rasmussen, Ashley E. Shirer

Transmission line foundation designers must rely on limited subsurface information, from easily accessible locations, resulting in subsurface uncertainty, increased design risk and increased construction costs. This paper presents a different approach for foundation analysis conducted in mountainous and alluvial floodplains located northwest of Phoenix, AZ. The region is dominated by fault-bounded, northeast dipping mountain ranges, where rock types and drillability can vary from granite to intact basalt. The valleys between are comprised of “basin-fill” deposits ranging from conglomerates and cemented soils to lose alluvium. Recently deposited alluvial fills can vary in depth significantly from location to location due to erosion and deposition from active and historic hydraulic features. To limit the subsurface uncertainty for foundation design, a phased approach using geophysical surveys along with detailed geologic reconnaissance was employed. Both compression wave and shear wave velocities were measured in order to identify the depth and properties of loose erodible materials from more scourresistant cemented, conglomerate, and rock deposits. These analyses were used in combination with limited subsurface drilling and sampling to evaluate direct embedment steel pole foundations for over fifty structures. Post analysis results from limited construction drilling reports were used to assess this approach.

Sep 8, 2021

By Rory Cameron, Chuck Edwards

"Stringent environmental performance criteria and regulations, and the desire to minimize water use have made membrane-based treatment and separation processes an attractive option. This has lead to many advances in all aspects of the technology. Membrane separation processes have found application in sea water desalination, brackish water treatment, decontamination of ground water, and wastewater treatment. Development of membranes with better resistance to harsh feed conditions has created new opportunities for the broader application of membrane separation technologies to mineral processing streams. There are examples in mineral processing operations, including treatment of acidic drainage, pre-concentration of pregnant leaching solution in heap leaching operations, separation of acids and metals from waste streams and intermediate process streams, as well as gold and cyanide recovery from a heap leaching operation. This paper provides a brief overview of membrane technology principles, followed by a discussion of current membrane technology applications relevant to the mining and mineral processing industry. The paper further explores the potential for the application of membrane separation as an integrated component in mineral processing operations.INTRODUCTION Increased regulatory pressures, emphasis on water conservation, and scarcity of water in arid regions have resulted in substantial changes in industrial practices in recent years. As a result, many industries have become more open to adopting innovative technologies such as membrane separation. The mining industry, which is typically very conservative, has adopted membrane separation as an effective end-of-pipe solution for effluent and acidic drainage (AD) treatment; however, its use as an integrated component in plant operations has progressed more slowly. With increasingly stringent environmental regulations coupled with the desire for low- and zero-discharge operations, the use of membrane separation technology for achieving acceptable environmental performance may be unavoidable in the future. The relatively small footprint requirement, versatility, and modular construction of membrane separation units facilitate their introduction into existing processes with a suitable feed stream. Membrane separation is not a stand-alone process that provides the ultimate solution to water and wastewater treatment; however, it can often be economically added to conventional waste treatment plants to increase throughput and/or decrease contaminant output (Mortazavi, 2008). Although membrane separation technology has become an established separation technique that is widely used in drinking water production and other industries, it is still considered an emerging technology within the mining and mineral processing industry. This technology offers many potential benefits such as clean water recovery from wastewater, significant reduction of volume requiring conventional treatment, decreased usage of reagents, and acid recovery, all of which lead to increased treatment efficiencies and lower reagent consumption. This could translate to smaller and more efficient plants with lower capital and operating costs and lower environmental impacts. Plant expansion may be facilitated by incorporating a membrane separation unit operation in order to utilize existing treatment systems at higher throughputs."

Jan 1, 2012

By M Wortley, R Morrison, T Rivett

The tracking of ore through process hold-ups such as stockpiles has been traditionally been difficult to achieve. The inability to pinpoint the exact source in the mine of material that is feeding a processing plant has led to inefficient mine-mill reconciliation processes. In addition, a lack of understanding of the behaviour of ore in process hold-ups such as bins and stockpiles often leads to poor predictions of plant performance and to poor reconciliation of this to the orebody.This paper reports on two short case studies. One case study addresses tracking ore from various parts of two mines to the concentrator. The other follows synthetic particles through the coarse ore stockpile. Both studies use radio-frequency identification (RFID) tracer technology. The paper concludes by discussing general strategies for implementation of such concepts into mine-mill metal accounting and reconciliation systems. As shown in this paper, reliable ore tracking systems will allow much more effective mine-mill reconciliations as well as the ability to model process hold-ups with regard to size by residence time distributions. This should, in turn, allow metallurgists to have a better understanding of the size and grade of material that will report to the plant at different process hold-up (eg stockpile) conditions.

Jan 1, 2009

By Jun Lu

There are many factors affecting the strength of pillar, including width-to-height (W/H) ratio, mechanical properties of coal and surrounding rocks, property of partings in the coal, and the interface property between coal seam and the roof/floor. In this paper, the effect of varying pillar?s width-to-height ratio (W/H=3, 5, 7, and 10) and coal/rock interface cohesion (Cj =50 psi, 150 psi, and 300 psi) on pillar strength has been studied. The confinement effect of W/H ratio and interface shear strength is investigated by studying their effects on the average minimum principal stress developed in the pillar. The deformation behavior of the coal pillar is investigated. It is found that the pillar?s transition from strain softening to strain hardening behavior depends on its W/H ratio and the interface shear strength.

Jan 1, 2008