Search Documents

By M. William Lallman

Potash production from natural brines of the Bonneville Salt Flats has a comparatively long history dating back to the start of World War I. However, it vas sot until the late 1930's that a successful commercial potash operation was achieved by a firm known as Bonneville Ltd. While improvements in operating techniques, pond design and equipment have been incorporated as they became available it should he understood that the basic technology developed in the late 30's and early 1940's by Bonneville Ltd, for potash production has not been changed significantly. The purpose of this paper is to present a brief review of the history, geology and hydrology of the Bonneville Potash operations and discuss the cur¬rent methods employed for brine collection, solar evaporation and the recovery of potash and other brine chemicals. A detailed study of the hydrogeology of the Bonneville Salt Flats wan made by L. J. Turk,1 Ph.D. thesis for Stanford University in 1969, under the auspices, of Kaiser Chemicals the Industrial Chemicals Division of Kaiser Aluminum & Chemical Corporation. Turk's thesis furnished much of the information presented in this paper.

Jan 1, 1976

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By Ross W. Smith

Microorganisms are increasingly finding use in mineral processing and hydrometallurgy both for the enhancement of mineral engineering operations and for the remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of sulfide ores and biooxidation of refractory sulfide gold ores, are established commercial processes. Others, such as the use of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Other uses of microorganisms are potentially possible. These include use of microorganisms in leaching non-sulfide ores, the flocculation or flotation of minerals and remediation of toxic chemicals discharged from mineral engineering operations.

Jan 1, 1993

By Maryam Ghodrat, Bijan Samali

Treatment of polymer-based wastes has a tremendous potential for generating alternative energy, reducing greenhouse gas emissions, creating economic and environmental benefits, and achieving a sustainable development of the energy sector. During the past few decades, plastic waste generation increased at a greater rate than the population, with the move towards single-use products. Also with raising the cost of oil-based products, greater emphasis should be placed upon the usage of plastic/polymer in the waste stream as a supplementary source of fuel. This study presents a techno-economic analysis of the recycling potential of plastic waste in Australia by evaluating the possible use of these wastes as a reductant in steel making incinerators. The study tries to shed light on a possible cost effective alternative route in the smart treatment of waste plastic in Australia.

Mar 1, 2018

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre's (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

Characteristics Analysis of a Bastnaesite Rare Earth Mineral for Recovery of Cerium

Sep 13, 2010

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

By D. G. Krige

Using chip sample data and spatial structure parameters from a large mined-out section of a South African gold mine the advantages to be gained from a regular underground borehole drilling programme have been investigated for short- and medium- to long-term planning based on block valuations. The results have been compared with the current position, which relies invariably on the extrapolation of limited peripheral sampling data from raises, gullies or stope faces. Some preliminary work has also been done regarding the implications of such underground drilling on costs used for the present pay limit calculations. The results of the study, though preliminary, show that the net advantage of advance regular underground drilling could be substantial and that a more intensive follow-up research is warranted.

Jan 1, 2003

By Francis Gray

Mr. F. W. Gray: It is not my intention to read my paper as it is too long, so I will touch only on the high lights. The Sydney field is the most favourable example of undersea coal mining that exists, and I have not been able to find anything like it elsewhere. The nearest approach to it is a field in England where the Whitehaven collieries are operating, but it has a lot of faults. The net result of these faults so far met with in the seaward advance of the workings has been to increase, by something over 100 feet, the gain in depth of cover, in a distance of approximately three and three-quarter miles. In the Sydney field there are no faults of any consequence. On the east side, the English measures rise. In Australia the sea bottom fell and the cover became too light. On Vancouver Island the coal ran out, and in Japan the seams are steep and contorted. The Chilian fields resemble our own to some extent. An inundation of two collieries took place there some time ago, due, it is said, to the rise workings being allowed to approach the sea bottom too closely in the vicinity of a fault. The Cape Breton undersea field has been proved over a frontage of about thirty miles and has been attacked and penetrated for a considerable distance along that front. We have passed the prospecting stage and now generally use developed land areas as points of attack to win the undersea coal. Of our mining under the sea, it can be said that, with the exception of No. 1-B and Princess colliery, Sydney Mines, no real attempt has been made to win the undersea coal.

Jan 1, 1927

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

Triboelectric Separation - Beneficiation of Coal The performance of triboelectric separators is highly sensitive to the selectivity of the particle charging process. This paper presents a quantitative study on triboelectric coal beneficiation. The performance of different charging media was studied. Stainless steel was identified as having a work function between that of coal and silicate gangue and found to be the optimum charging medium for coal beneficiation. Recent results from separation tests were performed where silicate gangue was separated from crude coal using a parallel plate free-fall separator are illustrated.

Sep 13, 2010

OZ Minerals Limited owns and operates the Prominent Hill Copper-Gold Mine, located 140 km southeast of Coober Pedy in far north South Australia. The Prominent Hill mine comprises an open cut mine with an initial 10 year mine-life and an 8 Mtpa conventional grinding and flotation plant to produce high quality copper-gold-silver concentrates, which are exported by road to local customers and by rail to the port of Darwin for shipment on to Southeast Asian smelters. Mine and process operations at Prominent Hill are licensed to abstract a water supply of up to 26 ML/d, sourced from a borefield located 40 km and extending to 80 km east of the mine. The arid climate of the broader Prominent Hill region means that groundwater is important for sustaining community and pastoral industries in the region, and security of water rights for third party users is a critically important water management issue posing a significant challenge to the development of Prominent Hill. Depth to water table and the typically high salinity of groundwater in the region means there is little environmental dependence on groundwater within the immediate Project area (mine lease and wellfields). The Prominent Hill mine and associated infrastructure lies within the South Australian Far North Prescribed Wells Area (FNPWA), which was principally defined to ensure the ongoing security of the ecologically, socially and culturally significant GAB springs, of which the closest are found around 150 km northeast of Prominent Hill, and only 50 km northeast of the water supply borefield. Prescribing of the FNPWA meant that OZ Minerals was required to demonstrate to both State and Federal Government agencies that the mine's water supply is independent of that which supports GAB springs and other third party water users in the region. Recognising these potential obstacles, OZ Minerals successfully defined and developed a previously unknown industrial quality groundwater resource, separate from other important groundwater resources in the region that supply community, pastoral and environmental users, ensuring third party water user sustainability.

Jun 1, 2010

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By J. Guerrero, O. Pavez, N. Toro, A. Nazer

In the 19th century, mining in northern Chile was of great economic importance. Today, the ruinsof the copper smelters and abundant fragments of refractory bricks from their furnaces remain. Therefractory materials have not been previously studied. the origin, physical and chemical properties, and compressive strength of 10 different samples of historical refractory bricks collected on-site were investigated. The characterization results showed that the bricks are silico-aluminous, unlike the magnesium-chromium bricks used by current foundries. It was determined that 90% of them were produced in the UK and 10% were manufactured in Chile. The phases present are mullite, quartz, cristobalite, and tridymite, and the chemical composition corresponds mainly to SiO2. The compressive strength of the historical bricks is similart to those currently used,. These results may contribute to the knowledge of the 19th century mining and metallurgical historical heritage of Chile and the UK.

Jul 5, 2023

By Jim Owens

The methodology of quarrying changed significantly in the Indiana limestone industry in the 60 years between Sept. 11, 1941 and Sept. 11, 2001. The former was the date of the Pentagon groundbreaking ceremony, while the latter was when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on Sept. 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction(and Indiana limestone) industry can accomplish when working toward a common goal.

Jan 1, 2005

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003