Search Documents

By Scott Turner

PRESIDENT SCOTT TURNER officiated as chairman of the opening session on mining methods, Monday morning, Feb. 15. The first paper was that of Max H. Barber on open-pit mining in the Lake Superior district, read by C. F. Jackson. W. L. Taylor stated that liquid-oxygen explosive had been tried but that the operators are satisfied with the explosives used; lb. of dynamite breaks one ton of rock. Although black powder is considered the most effective explosive, the factor of safety has decided in favor of high explosives. Lucien Eaton told of the Michigan Lime and Chemical Co.'s large L. 0. X. plant at Rogers City, Mich. Mr. Turner referred to this plant, also said that the Bureau of Mines is shortly to issue Bulletin 349 completely covering the use of L. 0. X. from its inception. W. D. B. Motter, Jr., gave some items concerning Chuquicamata, Chile. Twelve years ago the blasts moved 850,000 to 1,000,000 tons, but average shots now move 250,000 to 300,000 tons. One pound of L. 0. X. breaks 3.7 tons, against 3.1 tons by dynamite. Another speaker told of some large dynamite blasts in open pits, one of 360,000 Ib. in March, 1931, and another of 430,000 lb. to be shot in 1932. Tests have been made to determine the effect of large shots on the surrounding country. Mr. Taylor said that 4- and 5-yd. shovels were preferable to those of 8 yd.; their performance is better and cost is lower.

Jan 1, 1932

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By David S. Yang

The Cement Deep Soil Mixing (CDSM) method introduces and mixes cementitious materials with in situ soils using hollow-stem rotating shafts equipped with a cutting tool at the tip and mixing paddles above the tip. CDSM generally produces a soil-cement panel consisting of three overlapping soil-cement columns. The soil-cement panel is then extended to form walls, which are effective for excavation support and groundwater control due to the continuity and low permeability of soil-cement walls. Two design approaches could be taken in the application of CDSM for excavation support: 1) single wall design and 2) gravity wall design. The former one is treated as a wall technology and the latter one is treated as a soil stabilization method. This paper will review the CDSM equipment and installation procedures for the construction of these two types of soil-cement walls. Four case examples are used to illustrate the design and application of these two types of soil-cement walls.

Jan 1, 2003

My selection of the Australian coal industry as the theme of this Presidential Address arose from the fact that it is one of our most important mineral industries. The industry is presently prospering.M.ore coal, mostly of better quality (except for certarn power-house types), is being produced more cheaply in terms of real money than at any time in the past, and exports overseas are currently at a highlevel.In. spite of this, concern has been expressed in certam quarters about the future of some phases of the industry; for example, there has been some public comment on the selling price of our coking coal to Japan, the possible over-export of our coking coals from New South Wales, the introduction of foreign capital to develop large-scale mining ventures in Queensland, and the proposed export of substantial quantities of coking coal from the same State.Furthermore, proposals for the introduction of atomic power plants into several States well endowed with reserves of coal have given rise to comment, and recently the Department of National Development(1968) warned that insufficient attention is being paid to "orderly development and careful husbanding of the nation's coal.To reach a balanced judgment on whether these views are well founded it is essential to make a broad survey of the present position of the coal industry in the Australian economy. I therefore propose to deal briefly with several aspects, and to comment, in particular, on the important subjects of exploration and research in progress at present on Australian coals.Detailed descriptions of the Australian coalfields are to be found in existing technical publications (e.g.. Andrew, 1965; McLeod, 1965) and the data on coal reserves have been progressively revised as more accurate information has become available. In New South Wales detailed knowledge of the coal reserVes is limited to under 20 per cent of the sur...

Jan 1, 1969

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

Recovery of Tantalum Capacitors from Waste Printed Circuit Boards Using a Pneumatic Separator

Sep 13, 2010

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011

By D. E. Cameron

The Cannon mine, located in north-central Washington is mining gold hosted in silicified Eocene-age arkosic sediments arrayed along a regional strike-slip fault system. Branches of the Eagle Creek fault have broken the Chumstick Formation into blocks and wedges, and have caused intense deformation of stratigraphy in the mine. Mineralization at the Cannon mine (B-Reef) and O-Reef (L-O mine) is a bulk silicification with high grade cross-cutting veins containing principally electrum, silver sulfosalts and pyrite in a gangue of quartz, adularia and calcite. Orebodies have very irregular shapes, but tend to follow stratigraphy and high-angle pre-mineral fault breccias and splays developed adjacent to the major faults. Both B-Reef and O-Reef occur at significant bends in the regional trend of major fault strands. Mean gold grades decrease upward from near sea level to the 300 m elevation at the Cannon mine. A new discovery, the A-Reef is hosted by a moderately dipping structure which is at a low angle to bedding. Fluid inclusion studies of B-Reef ore zones indicate dilute ore-bearing fluids boiled at temperatures between 185 and 2850 C at a depth of 1 km. Many ore zones are bounded by sheared mudstone and claystone and a much broader halo of argillic alteration comprising illite, smectite and sericite. Trace and major element analysis by ICP-ES for 33 elements, LECO for S, Hg by CVAA and gold by AA-FA shows dispersion patterns hundreds of meters outward from the known orebodies in the Cannon mine. Geometric mean comparisons, hierarchical R-mode cluster analysis and single element spatial plots show that Hg, As, Sb, S and K/Al compose a suite of elements which are significantly dispersed away from, and increase toward mineralization. Ba, Ca, Na, Mn, V and Zr decrease toward mineralization. The suite is more selective than gold with respect to known mineralization within the exploration area.

Jan 1, 1992

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By Segnit E. R

Results are reported of a study of the reactions occurringin the combustion of chaIcopyrite particles underconditions simulating those in the shaft of a flashsmelter.The reactions were studied using kinetic and mineralogicaltechniques. Reactions. rates above 500°C wererapid, most of the reaction taking place in less than 50ms. Final products were copper-iron ferrites with spineltype structures. Probable reaction mechanisms are discussed.

Jan 1, 1977

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987

By Ayokunle Adewale Akinlalu, Sunday Bayode, Sherif Olumide Sanusi, Joshua Oluwagbenga Adeboye

Gold occurrences have been reported in Alagbede, southwestern Nigeria, but a mineral potential map (MPM) to guide academics and investors in the area is still needed. As a result, geophysical methods (aeromagnetics and aero-radiometry) have been used to assess the potential for gold minerals in the area. Several enhancement filters, such as reduction to the equator, upward continuation, analytical signal, second vertical derivative, and power spectrum analysis, were applied to the aeromagnetic data to understand the subsurface geology better. The enhancement filters applied to airborne radiometry data are K/eTh, ternary color composite, F parameter, and deviation from the ideal K values (Kd). Geophysical data analysis was used for structural mapping and geological reconstruction, while aero-radiometric data was used for hydrothermal alteration mapping. The primary trend observed in the area’s magnetically inferred structural framework map is NE-SW, while a few are in the NW–SE and E-W trends. These observed trends show that the study area suffered at least three deformation episodes. Geological evidence of gold mineralization, such as favorable lithology, geological structure, and hydrothermal alterations, has been fused to produce a reliable MPM of the area. The geographical location of the existing mineral sites in the investigated area agrees with the geological structures and the MPM produced there. Thus, the systematic approach adopted in this study can be extended to other supracrustal belts of a typical Precambrian basement complex worldwide to ensure the reliability of orogenic gold mapping and resource management.

May 9, 2023

By R. M. BUCHANAN

The segment of Canadian industry based on smelting of alum in um and manufacture of consumer products is based entirely on imported alumina and bauxite. In the absence of Canadian bauxite deposits, consideration of anorthosite, a less desirable aluminous rock, is being undertaken as one alternative in maintaining assurance of supply. Anorthosites in Canada cover many thousands of square kilometres of the Precambrian Shield. Although compositions vary widely among Canadian anorthosites, many appear to exceed the specified minimum of 25% A I 20 3 in bodies containing more than the required JOO million tonnes. A lthough most Canadian anorthosites are of Precambrian age, one located in British Columbia has been identified as being Middle _Cretaceous.

Jan 1, 1984

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008

By Gang Guo, Zhong Liu, Yi Zhang, Jingchun Lu

"Abstract Application of soil displacement screw pile (known as SDS pile) has been experiencing accelerated growth in Chinese deep foundation industry because of its technical advantages, environmental benefits, and cost effective as well. As bored displacement piling, SDS piles are able to perform better than non-displacement piling such as CFA plies due to changing the stress state in the soil around SDS piles during the installation. Therefore the design methods between the conventional pile type and SDS pile type have some differences. Based on the methodology research, current Chinese piling rigs, displacement augers and piling projects are introduced, and the current design approaches for SDS piles in China are also described. Moreover, the design results are verified by using full scale load tests, and a part of the research results of SDS piling system acquired in China are presented.IntroductionThe Continuous Flight Auger Pile, also known as the CFA pile, has occupied about 22% in the pile market all over the world (Van Impe, 2004; Bottiau, 2006). The CFA piles are usually used for large diameter (600mm~1200mm) pile foundations and deep excavation projects. Whereas the small size CFA piles (400mm~500mm) are mainly applied for composite foundations in China. In the past 10 years, the new technology of soil displacement screw piling has been applied worldwide (Prezzi et al., 2005). And it is also extensively used for high-rise buildings, industrial plants and railway projects in China (shown in Figure 1)."

Jan 1, 2014

By J. Châteauneuf, R. Dupéré, D. Mrabet

"In gold processing plants, it is common to start gold cyanidation in the grinding circuit by simple cyanide addition or as a result of recycling residual cyanide. In such cases, advantages such as a decrease in gold lockup and reduced leach time have been noticed. The prevailing conditions in grinding circuits such as intense mixing, particle breakage and friction or high temperature are quite different from those found in tanks and so is the resulting cyanidation behaviour. To gain a better understanding of the cyanidation behaviour in mills and of the pertinence of cyanide addition in grinding circuits, lab tests were conducted using an industrial ore from Canadian Malartic mine. In this study, the effects of different parameters on cyanidation in grinding circuits were examined; parameters such as such as temperature, dissolved oxygen, cyanide concentration and pH. The results showed that the kinetic benefits of high temperature in the mill can overcome the low dissolved oxygen concentration thus leading to an overall gold dissolution kinetics improvement for temperatures up to 50°C. However, gold leach in the studied grinding circuit at lab scale caused an increase in cyanide consumption with a higher generation of iron cyanide and SCN-. These results were confirmed by tests in the Canadian Malartic plant where the cyanide addition was moved from the SAG mill to the leaching tanks resulting in a 20% savings in cyanide consumption.IntroductionCyanidation in grinding circuits can benefit gold processing by decreasing gold lockup and by reducing leach time. However, other aspects regarding gold and cyanicide dissolution come into play in the conditions prevailing in grinding circuits. Indeed, high turbulence, high temperature, recycling load, friction and particle breakage make cyanidation behaviour in grinding circuits different from in-tank cyanidation (Marsden and House, 2006). In several cases, cyanide in grinding is limited to a very low level or completely avoided such as in circuits with gravimetric separation, for ores requiring oxidative pretreatment or for preg-robbing ores. In other cases, water management imposes a certain recycling of residual cyanide. This problem is generally addressed by a case-by-case approach. However, the chemistry of cyanidation in mill circuits is worth investigating in order to assess the advantages and disadvantages."

Jan 1, 2016