Search Documents

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By L. M. Luckevich

Gypsum is a product from the neutralization of sulfuric acid by lime or limestone. This paper will discuss specifications for gypsum used in wallboard, cement and agriculture and the factors affecting its utilization potential. Process conditions during the neutralization which enhance or inhibit utilization potential will be included. In addition, this paper provides a technical and economic perspective of the gypsum industry in North America with a view to the factors affecting the utilization of synthetic gypsum in traditional applications. Current production and consumption of natural and synthetic gypsum in Nonh America are described and the impact of their differences on utilization options are discussed.

Jan 1, 1996

By Ian Bruce

Tailings and water management facilities are essential and integral components of mine and mill operations. They must be managed for the long term in order to ensure that safe and environmentally responsible stewardship is achieved. Toward this end, in 1998, The Mining Association of Canada (MAC) published A Guide to the Management of Tailings Facilities, which recommended the implementation of a tailings management framework (Figure 1) to integrate environmental and safety considerations into each stage of the life cycle of a tailings facility, from initial site selection and design, through construction and operation, to eventual decommissioning and closure. By February 2000 it was becoming apparent that while mining companies were making significant progress toward implementing and documenting tailings management systems, and integrating them with overall environmental management systems, further effort was warranted in their application at the operational level. In particular, a need was identified for further guidance in preparing manuals that outline procedures for the safe operation, maintenance and surveillance (OMS) of tailings and water management facilities.

May 1, 2002

Copper mineralization associated with minor molybdenum, silver, and gold occurs in a hydrothermally altered brecda within a granodiorite mass of Upper Permian age. A dyke system of rhyolite, dacite, and andesite forms plug-like bulges near the breccia and probably caused mineralization as a late stage effect.Base metal sulphides occur as disseminations, fracture and cavity fillings in the breccia. A pyritic halo in hydrothermally altered granodiorite surrounds the breccia and grades into unaltered granodiorite. Drilling during 1969 indicated the grade is subeconomic.

Jan 1, 1972

By Jones S. C

A specific arc can be cut in hard rock formations using a specially designed multistep piloI bit, variable sized drift joint and long heavy control rod as a stabilizer rather than the Vaughan Thompson "Lifting" arc cuttingequipment. The rate of deflection can be controlled after an initial determination of behaviour in any particular rock type.

Jan 1, 1966

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By E. S. Schubert

Keywords: co-generation, furnace CO-gas cleaning, disintegrator scrubber, Theisen In a closed, electric, reduction furnace, no oxygen enters the furnace from the surrounding environment. The off-gases are thus not ?burnt? and therefore contain a considerable amount of CO and H2. Traditionally these gases have been captured and burnt in a flare stack. Recent developments have led operators of such furnaces to revise this strategy and to consider utilising these gases as a fuel for gas-fired generator sets to produce electricity, thus becoming more energy efficient. On 31 March 2010 the new emission standards, in accordance with the Air Quality Act, Act 39 of 2004, were promulgated. The minimum emission standards according to the act require that the particulate matter emissions from the primary fume-capture systems on closed furnaces for ?new plants? in ferroalloy and calcium carbide production not exceed 50 mg/Nm³ and 25 mg/Nm³, respectively. By implementing co-generation, the producer automatically complies with the new environmental emission standards for an off-gas. As much as 30% of the electrical power cost, which is set to double in the near future, can be saved by partly generating one?s own electrical power. In December 2010, the National Treasury published a discussion paper for public comment, one entitled ?Reducing greenhouse gas emissions: The carbon tax option?. Irrespective of how the tax is finally implemented, it will result in an increase of production costs in affected industries. This paper focuses on the characteristics of a furnace-off-gas cleaning system for closed ferroalloy smelters, characteristics that meet the requirements of both reducing solid-matter emissions and operating a safe and reliable gas plant.

Jan 1, 2011

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

The major factors limiting the establishing of vegetation on the shale and sandstone wastes at Minto are high exchange acidity and low pH (shale pH 4-5, sandstone pH < 4). In the first revegetation program (1967-74), 3.8 million trees were planted without grading on 4,000 acres (red, jack and scots pine and black locust). White dutch and sweet clover, birds-foot trefoil and red top were established in selected areas, and ponds were stocked with brook trout. In the second phase of reclamation, beginning in 1979, a comprehensive plan will be initiated which will allow for forest production, wildlife development and recreational activities.

Jan 1, 1977

By M. Paul

"INTRODUCTION In 1990, the uranium production of SDAG Wismut in East Germany was stopped. 45 years of inconsiderate destructive exploitation had scarred both landscape and nature. With the “Wismut law” which came into force in December 1991, the Federal Republic took responsibility of the remediation of the legacies from former uranium ore mining and milling in Saxony and Thuringia. A unique opportunity turned out in order to remove environmental damage, to enhance the life quality of the local population, to shape new landscapes and to advance the economic restart. (1) The results of nearly 25 years of remediation activity are evidence that this opportunity was used at all former SDAG (Sowjetisch-Deutsche Aktien-gesellschaft) Wismut sites. The reference project “Wismut“ has evolved into a joint project of all parties involved and radiates beyond the affected regions. This is particularly reflected by the Know-how transfer starting from Wismut and the increasing activities for third parties abroad.WATER MANAGEMENT AT WISMUT REHABILITATION Within the Wismut project, water management and conventional technical water treatment are by far the most cost-intensive long-term tasks of the remediation programme. Over the medium term, there is no viable alternative to the operation of active systems to catch and treat contaminated mine waters at the Ronneburg, Schlema, Königstein, Pöhla, Seelingstädt and Helmsdorf sites. Based on the status quo, this paper outlines the key issues of the Wismut GmbH water management strategy over the medium and long term. It is focused primarily on achieving protection goals for potentially impacted water bodies in the surroundings of Wismut sites and on optimising associated remediation expenditures as well as on creating the prerequisites for achieving low post-remedial care and maintenance or walk-away system status over the long term. (2) The applied mining practices during the active SDAG Wismut period have not been up to the high standards of modern mining operations and their requirement to leave former production premises and deposited residues in a condition that was not only physically but also chemically stable. Rather the emission of mine and seepage waters laden with high acidity, metal and salt content is a frequent corollary and difficult legacy of historic mining and processing operations (4, 5). As a consequence, the control or mitigation, respectively, of environmental impacts associated with contaminated mine waters ties up enormous public resources worldwide (6, 7)."

Jan 1, 2016

By J. A. Kost

The objectives of this contract were to determine the amount, size, and deposition of float coal dust (74 x 10 microns) generated during the mining and transporting of coal in underground U.S. mining operations. Rock dust distributed by trickle dusters was also sampled. In addition to four belt-transfer points, two continuous and two conventional mining sections were sampled at five mines located in Pennsylvania, West Virginia, Kentucky, and Illinois. Float-dust samples were collected on deposition pans; total airborne dust was collected with MSA Model C personal samplers equipped with Unico filter casettes; Andersen cascade impactors provided relative size distributions of the samples. Production, airflow, and water flow were monitored to examine their effect on dust levels.

Jan 1, 1981

Triboelectric Charge and Separation Characteristics of Industrial Minerals The basic principles of triboelectric charge and separation of minerals and the factors affecting the entity of the charges developed on mineral surfaces are discussed and the surface pretreatment methods by which the electrophysical properties and thereby triboelectric charging and separation of minerals can be artificially altered/modified are reviewed. Furthermore, the triboelectricfication theory of materials is envisaged from the chemical concept of acid-base donor-acceptor and an attempt is made to correlate the physical concept of triboelectrification with the donor-acceptor properties. The triboelectric charge characteristics of the quartz, calcite and wollastonite mineral samples for different size classes were defined using different tribocharging medium. Based on the triboelectric charges acquired by mineral samples their energetic work function values are estimated. In addition, the main electrophysical properties, ie dielectric constant and electrical conductivity, of different size fractions of the mineral samples are measured and their donor-acceptor chemical properties were defined. A series of triboelectric separation tests were conducted to explore the possibilities for separation these mineral from each others. The results from the triboelectric charge and separation of the single mineral systems showed promising prospect in separating quartz, calcite, and wollastonite from each others. Finally, attempts were made to explore the possibilities to implement triboelectric charge and separation process to real ores. Promising results achieved when separation of calcite from silicate impurity was sought from a carbonate ore. A very high purity (99 per cent) calcite product was obtained at a recovery of 80 per cent. Interesting results were also achieved to concentrate wollastonite from a complex silicate ore containing quartz, different feldspars, wollastonite and other Mg-Fe silicates. In this case conditioning of the ore with salicylic acid at defined temperature and relative humidity was found to be essential to concentrate wollastonite. The outcomes indicate despite the fact that triboelectric charge and separation process has not been completely perceived, it pronounced to be an environmentally friendly and economically viable technique for minerals and wastes beneficiation. Being a dry beneficiation technique the process has special appeal, which must be explored further in particular for treating industrial minerals.

Sep 13, 2010

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

By Dennis P. Martin, Michael M. Fitz, James E. Friant

Methods for reducing the cyclic nature of drill and blast tunneling operations have been long needed. A miniature blasting system using 10 mm (.375 in.) holes, 0.91 m (36 in.) deep, and blasting only one hole at a time makes it practical for men to work behind a shield, remaining at the face during the entire process. A prototype automated module was developed to drill, load the hole and initiate the detonation without moving from the hole. A unique cost effective gell explosive and a novel, low cost initiation method were developed.

Jan 1, 1989

By Pratt V

The economic, social and political environment of the mining and minerals industries is, as we all know, volatile and affected by constantly changing international forces. In addition, the outcome of negotiations with overseas customers is often uncertain for long periods, or even unfavourable. The industries and companies represented at this Conference are in an arena of high competition, risk taking and enormous capital outlay. They are industries which our overseas markets (rightly or wrongly) have criticised for industrial relations problems, unreliable production and uncertain deliveries. They are industries which have an urgent need to be cost effective and competitive at all levels of activity.A critical factor in the mining and metallurgy industries is, therefore, its human resources and its human resource management. It requires the full use of available talent, innovation, skills and qualifications within its workforce, and the appropriate management of these resources.

Jan 1, 1985

By Linda J. Dahl

The U.S. Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ leach mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits which include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, proximity of ore minerals to the leach fluid paths, surface subsidence potential, and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental, and economic feasibility of in situ leach mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability, and porosity as they relate to in situ leach mining.

Jan 1, 1992

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

This report briefly describes the broad program of research and technologic work conducted by the Bureau of Mines on coal and related subjects during 1966. In addition to n description of investigations on mining, preparation, and utilization of coal, an account is given of the Bureau&apos;s work in mine health and safety, coal resources, mine explosives, and environmental conditions relating to coal mining and utilization. Details of most of the projects are reported in publications cited throughout this report. Centers and laboratories conducting the coal research and related investigations appear in appendix A; organizations, institutions , and companies contributing to the Bureau&apos;s coal research and technologic program are listed in appendix B.

Jan 1, 1967

By Maral Malekian, Pat Bellett, Eranda Tennakoon, Fernanda Carrea, Moe Momayez

Slope instabilities in open-pit mines pose a safety risk to workers and a financial burden on production. The direct impact of slope stability on safety and production makes slope failure predictions one of the important challenges in the mining industry. Predicting the precise time of slope failure has been the subject of much research in conjunction with the development of innovative monitoring technology designed to prevent sudden failures. This paper investigates the use of AutoRegressive Integrated Moving Average (ARIMA) model to predict the time of slope failure. Input data such as inverse velocity (IV) and dimensionless inverse velocity (DIV) from 20 slope failures were used to train the model predict the failure time. For comparison purposes, the time of slope failure using the traditional inverse velocity method is also provided. We show that ARIMA provides 90% more accurate predictions than the TIV approach.

Jul 12, 2023