Search Documents

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed a series of lab tests to evaluate the respirable dust removal capacity of an industrial air-cleaning fan. Limestone and coal dust were tested separately in NIOSH’s full-scale drill table simulator at the Pittsburgh Mining Research Division (PMRD). Gravimetric samplers with Dorr-Oliver Cyclones and 37-mm filters were used at two upstream and four downstream locations inside and outside of the drill shroud chamber. There were six tests performed for both the limestone and coal dust experiments. In the limestone tests, an average respirable dust concentration of 98.86 mg/m3 was achieved upstream of the air-cleaning fan. The filter results show that the averaged respirable limestone dust reductions were 7.84%, 8.81%, 10.94%, and 18.02% at the four sampling locations downstream of the fan. In the coal tests, upstream samplers achieved an average of 129.03 mg/m3 of respirable coal dust. The averaged dust reductions were 9.54%, 9.83%, 18.54%, and 19.21% at the four downstream sampling points. The results indicate limited cost benefits of using this technology because of the relatively low dust reductions determined from this laboratory study.

Feb 1, 2023

By H. B. Menardi

THE history, geology, ore deposits and current mining operations of the Huitzuco district have been described by C. W. Vaupell1 and the current mill operations by David Segura.2 This paper completes the story of Huitzuco with a description of the reduction of the flotation concentrates. The predominant ore mineral in the Huitzuco deposit is livingstonite, a rare, mercury-antimony sulphide (HgS.2Sb2S3). Other associated minerals include cinnabar, stibnite and elemental sulphur. The gangue is largely limestone and gypsum. Former operators mined a selected grade of ore, from which the mercury was recovered by an expensive, inefficient operation. A consid-erable tonnage of rejects and fills, carrying mercury and antimony, was left in the mine. In order to recover both mercury and antimony from these fills and also from newly developed ore, a combination method has been developed, by means of which the livingstonite is concentrated by flotation and the flotation concentrates subsequently reduced to metallic mercury and antimony. An essential part of the flotation treatment, as developed by Segura, is the use of copper sulphate as an activating agent. A typical analysis of concentrates now being produced at the property is as follows: Hg, 7.73 per cent; Sb, 26.40; Fe, 1.20; S, 29.68; CaO, 11.50; MgO, 7.25; Si02, 1.63; A1203, 0.65.

Jan 1, 1939

By R. J. Thompson

Well-designed and maintained haul roads are the key to minimizing truck haulage onroad hazards and costs, as well as increasing productivity. In practice, however, designing and managing a haul road for optimal performance is often difficult to achieve, especially when resources assigned to design and construction are constrained. By understanding how a road design is developed from geometric, structural, functional and maintenance considerations and, critically, the interplay between these components in design and operation, optimal performance can be achieved. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for safer and more efficient haulage systems, the truck manufacturers’ requirements for a more predictable and controlled operating environment and the recognition of human factors as a significant contributor to haulage accidents. While the human factor is the most problematic to address in a road design, the paper shows that the more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.

By John Starkey

"During the period June 2007 to March 2007, John Starkey of Starkey & Associates (Starkey) worked in Russia for High River Gold, supervising the engineering design work that was being done at the IRGIREDMET Research Institute, in Irkutsk Russia. The work entailed moving the Newmont No. 4 mill from Elko, Nevada to Berezitovy, a mine site north and west of the city of Skovorodino, in the Amur Region of Siberia. This was a grass roots project and required construction of all phases of the infrastructure and process facilities that are associated with a 5000 t/d open pit mine and CIP mill.During the course of this engineering design exercise, many aspects of doing business in Russia were encountered, with regard to laws, norms, and business practices. This paper discusses many of these findings. Also by living in Irkutsk, many observations on Russian life and social customs were made and these merit discussion from a general interest point of view.Prior to going to Russia, another engineering and ore testing firm (TOMS) had approached Starkey to find out if Starkey could assist them in upgrading their SAG ore testing procedures to Western standards in order to offer their clients turnkey projects, that included reliable SAG and AG grinding. TOMS was aware that Starkey had invented the SPI test but did not know that the SAGDesign test had by then been fully developed and was being offered commercially as the most accurate way in the world to design new grinding mills. They were also unaware that this new testing method had been patented by Outokumpu (now Outotec) and that this method allowed them access to a design method, through Starkey, that would lead to a manufacturer’s guarantee (by Outotec) of throughput and grind for any new semi-autogenous or autogenous grinding circuit, with or without ball mills.When Starkey started working at IRGIREDMET in June 2005, they also made a request to add a design method for SAG mills that would be considered acceptable to Western clients. From these requests, presentations were made in Russian to both institutes and each decided to join the SAGDesign Consulting Group as satellite members and buy a SAGDesign test mill to use with their Bond Ball Mill Work Index mills, to provide SAGDesign testing services. To complete the service, contracts have been put in place for Starkey to use these results to design new grinding equipment and to train engineers at TOMS and IRGIREDMET how to do this work.Starkey also undertook to train engineers at both labs to go into the field and to take the samples for SAGDesign testing programs. It is here where the SAGDesign testing service upgrades other grinding test programs because the samples to be used for design are professionally chosen, and the results will be much more likely to produce a satisfactory design. Starkey is a mining engineer and is uniquely qualified to do this task. This and the SAGDesign test are the key components that lead Outotec to offer a performance guarantee for mills designed by Starkey."

Jan 1, 2008

By C E. J de Ronde, I C. Wright

Oceanic subduction-related volcanic frontal arcs extend over 20 000 km within the western Pacific basin and over 21 500 km worldwide, yet they remain largely unexplored with respect to active seafloor mineralization. Systematic exploration of 26 major submarine volcanoes along ~840 km of the Kermadec arc northeast of New Zealand has documented ten (39 per cent) as being hydrothermally active. This frequency of venting is comparable to that on slow-to-moderate rate spreading mid-ocean ridges, which comprise ~80 per cent of the 60 000 km-long global system of spreading centers. The chemistry of fluids discharged from the Kermadec arc volcanoes is moderated by magmatic components in both the gaseous (CO2 + SO2-H2S) and liquid (Fe) phases at very high concentration.The high frequency of venting coupled with chemically rich discharge discovered during this first systematic survey of any arc system forecasts submarine arcs as being important sources of chemicals to the oceans and as potentially lucrative exploration sites for seafloor mineralization. The exploration protocols developed during these surveys include bathymetric mapping of mostly unknown volcanic edifices, followed by detailed water column profiling and sampling to detect and characterize volcanic fluid emission signatures. These procedures are being refined as the survey progresses, both for efficiency and as direct seafloor observations become available for predictive application of water column plume information to guide seafloor mineral exploration.

Jan 1, 2002

By Pierre Sauvé, Alex Makila

"The Camflo stock of porphyritic quartz syenite is an irregular pipe-like body 200 metres in diameter injected along the axial plane of an E-W trending F2 fold, near the contact between the. Kewagama and Malartic groups. The stock plunges 55° to the NE, almost parallel to the fold axis. The stock, exhibiting pervasive, weak cataclasis with numerous, locally auriferous quartz veinlets, is cut by minor faults striking WNW and dipping about 45°NE.Two types of gold ore are distinguished at Camflo: ""porphyry"" ore and ""fault zone"" ore. ""Porphyry"" ore, accounting for 90% of the gold produced, forms wide zones within the stock. The zones are irregular in shape but tend to be oriented E-W in plan view (on a horizontal plane) and are elongated paraliel to the plunge of the stock. These zones are more abundant in the northern part of the stock. Differences between ore and barren porphyry are not obvious. ""Fault zone"" ore occurs outside the stock along minor faults, particularly in differentiated sills offer rodiorite and felsic granophyre. Gold grade is roughly proportional to the pyrite content which in turns depends in part on the original magnetite content of the host rock. Although both types of ore show some correlation between Au and S, the Au/S ratio is considerably higher in porphyry ore.The bulk of the gold is in quartz syenite and in felsic granophyre, the most brittle lithologies at the mine. Presumably, the vertically continuous, pipe-like stock, made up of shattered rock, provided the main channelway for the ascending mineralizing solutions."

Jan 1, 1990

By C. P. Haller, S. J. Aresco, R. F. Abernethy

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash- softening temperature of ash, the free-swelling index, and the hardgrove grind- ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruc- tions issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the con- tractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal. The Government purchased approximately 5-1/4 million tons of coal in fiscal year 1953. In connection with these purchases, the Bureau analyzed 11,435 samples. These are published for the use of Government officials and the public. A series of publications has been completed on coal analyses by States, or, where production is small in any one State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications con- tain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals. Previous publications in this series are: Bulletin 516, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Years 1948 to 1950 Inclusive); Report of Investigations 4934, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1951); Report of In- vestigations 4972, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1952). Following are the Bureau of Mines technical papers published by States, with their numbers: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement 645); Pennsylvania Anthracite, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supplement 618); West Virginia, 405 and 626; and Wyoming, 484.

Jan 1, 1955

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

By Steve Dillingham

Whenever misfired holes or portions of misfired holes remain after a blast is fired, a hazardous situation exists until the unfired explosive materials have been disposed of properly. Yet, there are so many factors that can contribute to misfires that it is impossible to give blanket instructions on how to handle them. To complicate matters, misfires today are rare due to reliable blasting products. As such, it isn’t very surprising that many blasters have never had to deal with a misf i re condition. While the likelihood of a misfire occurrence is minimal, you should always be pre p a red to handle a misfire should you be involved in such an event. To begin, every blaster and blasting org a n i z a t i o n should develop a misfire policy which contains the company’s safe operating pro c e d u res, emergency contact list, as well as any regulatory compliance re q u i re m e n t s . Tailgate and/or company-wide safety meetings should communicate the company’s contingent misfire pro c ed u res and any special site-specific precautions BEFORE the start of any project.

Jan 1, 2004

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By E. H. Rose

IN the realm of ore dressing the most pregnant feat of all time was announced in 1945: the winning of the mineral raw materials which made the harnessing of atomic energy possible. Lost in the stupendous implications of the end result, in the two billion dollar hugeness of the project, and in the famous names attached thereto, the fact that crude uranium ores had to be concentrated received relatively little notice in the press. Only the final link in the concentrating chain was publicized-ether extraction of uranyl nitrate, developed by Hoffman and carried on by the Mallinckrodt Chemical Works, or methods developed by the Ames group under Spedding. Some of the earlier links represented less glamorous but equally difficult and exacting research. One may only speak a word of admiration for those who worked hard, accomplished much, and said nothing. The universal lament for most of the year was "man shortage." A group of Canadian engineers expressed it as "being so short of labor that no labor was available to develop laborsaving devices." . Despite this, an outstanding amount of mineral-dressing progress was made in 1945. Necessity allowed no alternative. The insatiable demand of war for minerals forced the exploitation of lower and lower grade ores, and of others not before considered of commercial character or use, requiring the mineral dresser to fight for and win new bridgeheads on the home front.

Jan 1, 1946

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By Michael Rieber

Among the principal gathering/distribution systems for coal is over-the-road trucking. Where alternative trunk line modes such as barge or rail links are weak or nonexistent, trucks may, particularly for relatively short line hauls, act as substitutes. Their major application, however, appears to be in connection with smaller mines or coal users particularly where terrain problems are significant. Truck use has increased as rail lines have been abandoned or suffered neglect. For example, in 1956 about 38 percent of the coal transported in eastern Kentucky and about 8 percent of the coal moved in western Kentucky went by truck. By 1975, the percentages were almost 77 percent and 26 percent, respectively [4,U-11]. While rail route .limitations and deterioration played a part in the change, increased emphasis on road building, particularly during the 1950's and 1960's, and improved truck load capacity and efficiency were also important.

Jan 1, 1977

By A. E. Raddatz

The Bureau of Mines is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nev., hot springs ores. The deposit contains disseminated tungsten that cannot be beneficiated by conventional techniques and must be treated by hydro-metallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hours, quenching in a solution containing 1.5 parts of Na2C03 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution-to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hours, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 wt-pct W03. The pregnant solution contained 11 g/l W03.

Jan 1, 1982

The growth of "Unit Load-cargo handling technology in world cargo lin- er trades over the last decade has cre- ated a situation in which special pur- pose-vessels (cellular container ships, roll-on/roll-off vehicle deck ships and Lash type vessels) are rapidly replac- ing conventional cargo ships, the principal means previously available for transporting heavy lifts. Consequently heavy lift traffic has tended to accumulate awaiting ship- ment, especially where discharge is required in "off beat" locations. A partial solution to this problem will be provided by new and small but exceptionally versatile ocean going heavy lift carriers now finding their way into world trade routes. These new ships combine extremely high lifting capacity, high manoeuvreability and exceptionally shallow draft with bow and stern Ro/Ro capability. They can handle rolling loads of exceptional size and weighing up to 1,000 tons Each. But the problem is a far larger and more serious but essentially a domestic one. Major industrial pro- jects in Australia will require pro- gressively heavier and larger plant and construction sites are becoming much more inaccessible. Whereas these new ocean going heavy lift carriers have ample capacity to satisfy part of the total transport requirement, there is clear evidence to show that domestic transport resources have little if any potential for increase in capability at the same rate as demand or at the same rate as sea transport facilities. Resolution of the larger problem is within reach but only through a pro- perly co-ordinated approach to future planning for the overall needs of large scale projects on a national basis. This co-ordinated approach must involve Federal and State government transport administrators, railway and highway authorities, shipping and road haulage interests and finally the planners of the projects which require these improved heavy haulage services.

Jan 1, 1973

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district's major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By Don Thompson

Canada’s oil sands are a controversial topic and virtually every newsmaker and layperson seems to have an opinion about this 179 billion barrel resource. The oil sands represent 97 per cent of Canada’s remaining oil reserves, but misinterpretation and misrepresentation of the facts are threatening development of a resource that generates significant employment and tax revenue for Canadians. Join Don Thompson, president of the Oil Sands Developers Group, as he dispels the top ten myths about Canada’s oil sands and presents an alternative perspective on an industry that can play a critical role in North America’s economic recovery.

Jan 1, 2010