Search Documents

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By C. G. Kirkpatrick

Analysis of the data produced by a wide-band, sensitive, horizontal, biaxial motion sensor has revealed several distinctive patterns before, during, and after a roof fall. The signals prior to the roof fall are similar in spectra, but one thousand times larger in amplitude, than those after the roof fall. Immediately preceding the roof fall, by two to twelve hours, five events occurred which were larger in amplitude and lower in frequency than even the large pre-roof fall background signals. An interpretation of these events is offered.

Jan 1, 1979

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

"IntroductionNOTE.-All figures on the supply and consumption of coal in Canada cited in this paper were collected and reported by the Dominion Bureau of Statistics. The friendly and efficient co-operation of the officials of the Bureau. is the foundation upon which it has been my privilege to rely in the preparation of this and two earlier papers ( 1). My thanks are due also to our own staff on the Dominion Coal Board, who spared neither time nor effort in helping to prepare this paper.STATISTICS are comparatively dull and, to many people, coal statistics are duller than most. Coal is, however, the one basic mineral upon which our whole way of life depends and it may be well if attention is drawn to this fact by an occasional statistical review of the coal position in Canada. The recent furore over the oil and gas discoveries has so obscured the basic position of coal in many minds that a little basic coal information may be useful. It is for this reason that, for the third successive year, a factual survey of the coal position is being presented.In the previous papers (1) explanations have been given of the basic considerations in the preparation of these reports and some special phases of the overall picture have been examined. For these explanations, the earlier papers may be consulted."

Jan 1, 1952

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By John E. Conley

The need for lightweight aggregate for use in concrete products ,and structures has caused the Bureau of Mines to undertake an investigation to determine the availability of suitable raw materials and to study methods, procedures, and equipment to supply that need. Evidence is at hand to prove that the shortage of lightweight aggregate is nationwide. A survey recently covered in a report (13)5/ by the Construction Branch of the National Housing Agency has pointed out the locations in which lightweight aggregates are produced. A study of this information discloses that the producing centers are widespread, and that certain areas, notably the region east of the Mississippi River, and especially the sections along the Atlantic coast line and the Southeastern States, have only a few such plants. Certainly, many localities are badly in need of installations equipped to provide an ample supply of high-grade lightweight aggregate. The work undertaken by the Bureau of Mines includes investigation of the use of clays, shales, slate wastes, coal-mine wastes, diatomite-clay combinations, and various other 'mineral mixtures as possible raw materials. Likewise, special consideration has been given to the development' of equipment and techniques to produce the lightweight products.

Jan 1, 1949

By R. M. Santmyers

Thorium and cerium are two of the group of elements known as "rare earth metals," and are obtained from the mineral monazite. Previous to the employment of thorium and cerium in incandescent gas mantles these elements were nothing more than laboratory curiosities, as the rest of the rare-earth metals are to-day. The most important salts of these rare earths are the nitrates. In the manufacture of gas mantles, thorium nitrate is the principal ingredient and forms prom 92 to 99 per cent of the impregnating material; the other 1 or 2 per cent is largely cerium nitrate and is quite as necessary, for without it there would be little luminosity to the mantle when in use. When the mantle is "burned off," the nitrates are changed to oxides. The monazite used as a source of thoria contains from 6 to 9 per cent of thorium oxide (Th02) and 24 to 32 per cent of cerium oxide (Ce203). As only the thoria and a very small hart of the ceria from the monazite could be used in gas-mantle manufacture, for a time the residues consisting mostly of ceria with somewhat smaller quantities of other rare earths found no commercial application. Later, however, they came to be utilized in several ways, the most important being: (1) the manufacture of cored flaming arc carbons, a great, irmprovement over the plain arc carbons used in electric lighting; (2) cerium metal used in the manufacture of pyrophoric or sparking alloys or "flints" for automatic pocket lighters and miners' lamps; and (3) the production of special kinds of optical and art glass.

Jan 1, 1930

By F. J. Tozer

Canal communication between Lake Erie and Lake Ontario has been one of almost constant enlargement and reconstruction to meet the rapid growth of trade and commerce, and the consequent steady increase in the size of vessels plying the Great Lakes. The original canal was built by the Welland Canal Company. The first sod was turned in 1824 and the first vessel passed through in. 1829. There were 36 lift-locks, built of oak timber, 110 feet long and 22 feet wide, with a depth of water over the sills of 8 feet. The second canal, now known as the 'Old Welland Canal' was built by the Dominion of Canada (1842 to 1850). There were 26 masonry locks, 150 feet long, 26.5 feet wide and with a depth of water over the sills of 9 feet. The walls and banks were raised in 1853 to give a 10-foot draught. The third canal, known as the 'New Welland Canal, built by the Dominion of Canada, was started in June 1874 and the first boat passed through in the spring of 1882. There are 25 masonry lift-locks, 270 feet long, 45 feet wide and with a depth of water over the sills of 12 feet. The walls and banks were raised in 1891 to give a 14-foot draught. This is the canal in use at present.

Jan 1, 1926

By Stefan Larsson, Sebastian Adevik, Sadek Baker, Razvan Ignat

"Abstract Uncertain strength, deformation and flow properties in dry deep mixing columns often lead to conservative choices concerning design values where the design is regularly complemented with a surcharge fill. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle. The deformation properties of a ground improvement were studied by means of two small embankment load tests. The settlement measurements were also used in FEM analyses, where the effect of surcharge on creep settlements was investigated. Based on the results, the effects of the surcharge were considered negligible and could safely be ignored. The project is an example how the contractor can use a field test as an effective design approach.IntroductionGround improvement of soft soils with dry deep mixing columns, or lime-cement columns, is often combined with a surcharge fill. The main reason for using a surcharge is to force the primary settlement and some of the secondary settlement that would have occurred under the final embankment height alone, to take place under the surcharge loading. Another reason is to level out uneven settlements. Strength and deformation properties in improved soil cannot be sufficiently assessed in advance, before columns have been tested on-site, and this uncertainty often lead to conservative choices concerning design values. In order to compensate for a slow forecasted consolidation process, the design is regularly complemented with a surcharge. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle.Extensive research undertaken by Åhnberg (2006, 2007) shows, by means of triaxial and oedometer tests, that cementation processes and a load acting on the columns during hardening, makes the improved soil to behave as a heavily over-consolidated soil due to an increase in quasi pre-consolidation pressure. The effects of using a surcharge on the time for consolidation and creep properties are thus probably small, since the stress level does not normally exceed this quasi pre-consolidation pressure. A study presented by Venda Oliveira et al. (2013) shows that the stress level within small ranges has limited effect on the creep properties.This paper presents a case study where the deformation properties of a ground improvement using dry deep mixing columns was investigated by load tests on two small test embankments. The tests were performed at the Interchange Värtan project site, which is part of the Norra länken infrastructure project in Stockholm. The tests were not performed as a research project but simple load tests performed by the contractor with the purpose of rationalizing the design delivered by the client. One purpose of the load tests was to assess the deformations when the columns are loaded temporarily by overlaying concrete works. Another purpose was to provide some input data to a study of the effects of using surcharge on creep settlements. The analysis was conducted as finite element modeling using the commercial code PLAXIS, where creep settlements can be simulated using the built-in Soft Soil Creep model."

Jan 1, 2014

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 rears, until in 1936 probably more than 90,000 such units were put into use. According to reports of the Bureau of the Census 79,543 residential stokers were sold in the first 10 months of 1937 by 109 manufacturers. This rapid expansion has made itself felt in the coal-mining industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912; in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of the present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 years, until in 1936 probably more than 80,000 such units were put into use, According to reports of the Bureau of the Census 75,543 residential stokers mere sold in the first 10 months of 1937 by 108 manufacturers. This rapid expansion has made itself felt in the coal-mining, industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912 in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of tie present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this con¬dition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By C. W. Taylor, F. L. Martin

"THE DICTIONARY defines Metallurgy as the ""science or art of separating metals from their ores and refining them for use"". In these days, however, such a definition is not detailed enough.The modern science of metallurgy is based on two fundamental sciences, physics .and chemistry, and is sub-divided into two major fields: Process Metallurgy and Physical Metallurgy. These fields of metallurgy are now so comprehensive and involved that even the graduate metallurgist has to specialize in one or the other.In recent years, the relatively new science or technology of non• destructive testing has also entered the industrial scene, with tremendous impact and ramifications. So much so that, certainly, no .discussion on metallurgy can be complete without including some reference to it.Obviously, one paper cannot hope to cover in detail the relationship of the whole science of metallurgy to the mining industry. Consequently, only a very brief reference will be made to the field of Process Metallurgy, our major concern being with Physical Metallurgy and Non-Destructive Testing."

Jan 1, 1960

By C. J. Hall

Twenty eight pulse release sulfur hexafluoride tracer gas field tests were run in a multi-level multi-vein hard rock mine to measure leakage ventilation. The mine had numerous underground booster fans and gob filled old stoping areas and consequently numerous leakage paths. The tests proved that the equipment and methods developed by the USBM can be used successfully in complicated ventilation circuits. The leakage quantities varied each time a major change was made in the main ventilation circuit. Usually leakage quantities had to be remeasured after a main ventilation change, but measurements could be duplicated for anyone configuration except under certain defined circumstances. The characteristics of an individual leakage path could be determined from the difference between the measured sum of two paths and the calculated characteristics of one of the paths. Many leakage paths could not be evaluated accurately on one shift. Comments are made on equipment performance and field techniques. Programs for the calculation of gas concentrations and recirculation from measured data and for the mechanical integration necessary for a calculated leakage characteristic have been written for an HP 9810 and are included.

Jan 1, 1975

In early June, Rio Tinto?s chief executive officer Tom Albanese said that he expected demand for iron ore, aluminum and copper to double in the next 15 years. Driven by global industrialization and urbanization, Albanese said during his company?s annual general meeting that to meet the demand in 2030, the additional supply required will be equivalent to replicating the iron ore output of Australia?s Pilbara region every five years, adding another aluminum production complex the size of Canada?s Saguenay every nine months and developing another copper mine the size of Escondida, in Chile, each year.

Jan 1, 2010

By Betty L. Gibbs

Geologically simple deposits can be modeled quickly and easily with inexpensive gridding and mapping software. Hundreds of mines around the world use RockWorks99 and Surfer 7 for generating contour maps, producing log plots and cross sections, and performing other useful geological calculations. These programs are used by many mining operations as their only modeling and graphical software or they are used in conjunction with larger systems. The investment in learning time is low and the programs produce reasonable quality results with standard computing equipment. RockWorks99 and Surfer 7 provide a good level of capability while maintaining high quality technical integrity. Both programs are used for many applications in mining, oil and gas, environmental and other fields that require analysis of spatial data.

Jan 1, 2000

By Glenn Norris, Tyler Buckingham

"Gold recovery gains in the order of one to two percent have been realized in 2009 due to changes in the operation of the grinding circuits at Barrick Gold Corporation’s Hemlo - Williams Mill. The initiative known as “split milling” involves milling low grade open pit ore in one grinding circuit and higher grade underground ore in the other grinding circuit under different conditions.The philosophy of split milling involves processing higher grade underground ore at a lower throughput rate and a finer grind while milling lower grade open pit ore at a higher throughput rate and a coarser grind. Bench scale tests showed that the recovery relationship for underground ore sources was much more grind sensitive than that of open pit ore. This relationship proved to hold in the plant. The gold recovery gain due to finer grinding of the higher grade ore is much greater than the recovery loss due to coarser grinding on the lower grade ore. Since the majority of gold is being recovered at a higher rate, this results in higher overall plant gold recovery when compared to the traditional operation philosophy of blending the ore sources.The challenges for achieving the maximum benefits of split milling were two fold; the need to increase throughput on the open pit ore milling circuit and a means of grinding finer on the underground circuit. The former was met with an increase in SAG (Semi-Autogenous Grinding) mill ball charge, a basic “drill to mill” blasting campaign and changes to the primary gyratory crusher. The latter was met with a reduced SAG mill ball charge and a higher milling density. The resulting benefits in additional gold recovered are in the order of $3-5 million per annum.INTRODUCTIONThe Williams Mill processes ore from three different ore sources, the David Bell Mine (DB), the Williams Underground Mine (WUG) and the Williams Open Pit (OP). All three ore sources are located within the Hemlo camp in Northwestern Ontario adjacent to the Trans-Canada Highway. The Williams Mill was built in the mid 1980’s at which time it was designed to process 3,000 dry metric tonnes per day through a 22’ SAG mill in series with a 16’ ball mill. In 1988 a Mill expansion doubled the mill capacity by adding a second identical grinding circuit. A photo of the current grinding circuit can be seen in Figure 1. Today the Williams Mill processes an average of 8,000 tonnes per day of which approximately 60% is from the Williams Open Pit."

Jan 1, 2010

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defence for purposes other than the extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation's natural nonmetallic is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of the Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941