Search Documents

By C. A. Stetefeldt

Jan 1, 1895

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By Harry H. Ku

In December 1975, a report entitled "An Evaluation of the Accuracy of the Coal Mine Dust Sampling Program Administered by the Department of Interior" [1] was prepared by the Analytical Chemistry Division of the National Bureau of Standards (NBS), in response to a request by Senator Harrison A. Williams. Chairman, Committee on Labor and Public Welfare. The report attempted to evaluate the adequacy of (1) the personal sampler unit used to measure the coal dust concentration in the mines, (2) the procedures used by the Department of Interior (DOI) to analyze the dust samples obtained from mine operators, and (3) any recent studies made by the Department or private industry concerning the coal dust sampling equipment. Recommendations in the report of NBS included continued research efforts by the appropriate organization to correct the personal sampler deficiencies and to consider the use of area or stationary samplers as a supplement to the personal samplers. Concurrent with the NBS report cited above, the General Accounting Office (GAO) also issued a report in December, 1975 [2], suggesting that improvements are still needed in coal mine dust sampling programs and procedures relating to penalty assessments and collections. Among recommendations made by GAO, the following paragraph specifically called for actions by the agencies involved:

Jan 1, 1979

[Separates of all the Pamphlets published within the last three years (starting with No. 1469) are available, with few exceptions, at Institute headquarters. Separates of all the Technical Publications are also available. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.] METAL MINING TRANS. PAMPHLET VOLUME NUMBER TITLE AUTHOR MEETING AND PAGE* -1033 Relation of Air Pressure to Drilling H. W. Seamon New York 66,743, 766 Speeds of Hammer Drills Feb., 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York - 66,711 Feb., 1921 1 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples- Feb., 1921 1038 Discussion of Papers Presented in 1920 1041 Run-off and Mine Drainage - H. N. Eavenson New York 66, 624, 630 Feb., 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb., 1921 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 282 Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1921 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66,758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-steel Tests F. B. Foley New York - 66,789 Feb., 1921 1077-M Application of Magnetic Analysis to C_ W. Burrows New York 66,796 Root Drills Feb., 1921 1078-M Heat Treatment of Rock-drill Steel G. H. Gilman New York 66,779 Feb., 1921 1080 What is the Ideal Drill Steel? F. H. Kingdon New York 66,807 Feb., 1921 1081 Rock Drill Steels, etc. W. T. Ober New York 66,814 Feb., 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66, 715, 721 Definition and Valuation Sept., 1921 1084 Drill Steel from Hollow Ingots P. A. E. Armstrong New York 66,809 Feb., 1921 1088 Authors' Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A. E. Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft of Davis- J. L. Bruce Wilkes-Barre 66, 252, 268 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66, 580, 605 ment for a Mine Hoist Sept., 1921

Jan 1, 1926

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By J. W. Meier

Introduction The great importance of air warfare during World War II and the introduction of large-scale air transportation and airborne operations created an immediate demand for large quantities of high quality light alloy products. Before this war, the use of magnesium, the lightest structural metal, was barely in the development stage, and considerable research work was needed to overcome difficulties in improving its properties and to attain uniform quality in mass production of magnesium alloy products. The Canadian Bureau of Mines was frequently called upon, by various agencies of the Armed Forces and of the newly established war industries, to examine magnesium alloys that had failed in fabrication or in actual service, and to advise on proper alloys and fabrication methods to be used. Failures in magnesium alloy castings were connected mainly with lack of knowledge of proper founding and surface-protecting techniques. Most of the defects were due to microporosity and faulty heat treatment. To aid the foundry industry, small-scale investigations were started on the effect of various factors in the casting technique in order to improve the quality of the products. These investigations were made in co-operation with representatives of the Armed Forces and the Canadian magnesium industry. This work was later co-ordinated into a broad research programme on magnesium alloys, comprising problems on melting, refining, various casting methods, heat treatment, and testing of properties of standard and special alloys. This research programme? is still in force, and the present paper contains some results of the first series of investigations on magnesium casting alloys carried out at the Experimental Foundry of the Bureau of Mines.

Jan 1, 1948

By Albert W. Deurbrouck

This report describes the preparation characteristics of 23 coal samples collected from nine of the more significant coalbeds of Fayette County, W. Va. In 1963 almost 5.4 million tons of medium to high volatile B coals of excellent quality for metallurgical and steam markets were produced in Fayette County. Of the 23 coal samples collected 11 would require some upgrading to pro-vide metallurgical quality products, 11 were acceptable as received, and 1 was a noncaking coal. Cleaning these coals to metallurgical standards would require only the removal of the sink 1.58 specific gravity material which would be quite easy as very little near-separating-gravity material was present at this gravity.

Jan 1, 1965

By E. A. Anundsen

The prevention of accidents is considered a necessity at all branches and divisions of the Phelps Dodge Corporation copper-producing operations, and since there is a continual exchange of data on safety accomplishments between the various units, their safety programs are fundamentally similar. Variations in accident-prevention methods result from a difference in emphasis rather than from a difference in the elements themselves. The main copper-producing operations of the corporation ore conducted in Arizona and distributed as follows: Copper Queen Branch, mines division, Fisbee, and smelter division, Douglas, Aria.; Morenci Branch, mines division, Morenci, and smelter division, Clifton, Ariz.; New Cornelia Branch, Ajo, Ariz.; and United Verde Branch, mines division, Jerome, and smelter division, Clarkdale Ariz. As it is not feasible to describe here the safety programs of all branches and divisions, the program at the Clarkdale smelter has been selected for discussion. The United Verde Brach includes the mine and smelter purchased by the Phelps Dodge Corporation in February 1935 from the United Verde Copper Co. The mine at Jerome and the reduction works at Clarkdale are designated, respectively, as the mine and smelter divisions.

Jan 1, 1939

By Paul N. Freeman

This paper describes the in-situ performance of two IFS powered support installations at Betws and Penallta Collieries in the South Wales Coalfield, United Kingdom. Intensive monitoring of all powered support functions, strata movement, support/strata interaction and coal seam disturbance permitted an extensive evaluation of powered support performance for all periods of the mining cycle. The influence of support design, support rating, face design, proximate strata and scam section upon support and operating performance are discussed. In-situ performance is compared to design specification and to the requirements of Production Instruction 1982/6. Aspects which show significant variation are highlighted. Particular attention is drawn to the precise analysis of support/strata interaction in the form of canopy and base loading profiles. This illustrates the influence of support rating and configuration in determining the interaction of the canopy and base with the proximate strata. Extensometric monitoring of the coalface highlights the potential zones of disturbance within the seam which allied with support position monitoring provides an accurate basis for theoretical considerations of support loading. Conclusions are drawn, the application of which may enhance the performance and operation of IFS supports in thin to medium sections.

Jan 1, 1992

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933

Treatment of Gold-Bearing Oxide High-Clayish Ores The analysis of modern state of treatment technologies of gold-bearing oxide high-clayish ores showed that the main method applied both in Russia and abroad is sorption leaching and heap leaching with preliminary granulating. The use of any of these processes depends on many factors including average gold grade, site and area of a deposit, clay content and etc. The two processes are often used at the same deposit. In this case, rich ores are treated according to a plant technology, poor ores and ores with cut-off grade are treated with heap leaching. Both technologies possess their own advantages and disadvantages. A plant technology is characterised by high recovery with higher capital and operating costs at the same time. Lower recovery during heap leaching can be attributed to an unstable quality of ore granulating due to both technological and weather conditions. In case of poor high-clayish ores, the use of a combined ore treatment is possible and profitable. It includes the ore disintegration and a clayish fraction treatment by using a heap leaching. In this case, capital and operating costs reduce in comparison with a plant technology and the recovery increases in comparison with heap leaching. Sometimes it reaches a plant recovery. These ores possess special features. As a rule, gold is associated with ore fraction, so it liberates readily from the association with ore ore-forming minerals even with relatively coarse grinding explain their high solution velocity in a hydrometallurgical cycle. Clayish ores are characterised by high sorption activity to gold cyanide complexes as well as extremely low velocity of filtration and thickening of slimic pulps at the same time. The paper describes the options of oxidised high-clayish ores treatment, such as, a plant technology (PIP and CIP process), heap leaching and a combined technology (disintegration, heap leaching of a crystalline fraction and sorption cyanidation). The obtained results were used when selecting a treatment technology and during construction of a plant for oxidised high-clayish ores treatment.

Sep 13, 2010

Satisfactory means of managing growth in boom towns is a concern in mineral, energy and other large industrial developments. This session will include examinations of socioeconomic impacts, major issues such as social disruption, case studies, methods of managing growth, and concerns involving Indian lands. Innovative methods will be offered to assist the public, government, and industry in finding solutions to managing growth in rapidly growing communities.

Jan 1, 1979

By Jamal Rostami, Ataollah Rahbar

"Uma Oya Multipurpose Development Project is under construction in Sri Lanka. This project involves 2 Rolled Concrete Core (RCC) Dams connected through a tunnel currently under construction by Drill and Blast method. The water is transferred from first diversion dam to the 2nd regulatory dam and from which, it will be transferred through a 14 km headrace tunnel to the top of a 650 m deep drop shaft that feeds the high pressure water to an underground powerhouse and turbine chamber for generation of 120 MW of electricity. The Headrace and Tailrace tunnels are being excavated by two 4.4 m diameter double shield TBMs. The headrace tunnel has already passed 5km milestone and is mined in hard rock, while the tailrace tunnel has been completed in rather weak and fractured ground. This paper will review the history of the project along with the geology of the site. The operation of TBM in headrace tunnel will be discussed in more detail, focusing on the challenges of excavating through very strong and abrasive quartzite and gneiss on this site, as well as reaches of tunnel in high inflow of water reaching 400 L/Sec. INTRODUCTION This paper aims to introduce the Uma Oya Multipurpose Development Project (UOMDP) as a hydro mechanical project in Sri Lanka, targeted generating hydro-electric power, transferring water for irrigation purposes and controlling seasonal devastating flood. This project lies in the south-eastern part of the central highland region of Sri Lanka (Figure 1). The main part of the project is located in the south-western part of the Badulla district in the province of Uva. The south-eastern end of the project site is in the central west of the Moneragala district (province of Uva). Bandarawela is the largest urban setting within the project area, located halfway between the upstream and the downstream ends of the planned hydropower plant and combination of dams, tunnels, and downstream facilities. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya. The feeder (power) tunnel Lot consists of a headrace tunnel (L=15554m), the surge shaft (L=200m) and tank on the upstream of the vertical shaft, a vertical shaft with steel lining (L=650m), an underground powerhouse and a tailrace tunnel (L=3650m)."

Jan 1, 2016

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFI test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 1, 1986

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

The Midvale Slag Site covers 300 acres in Midvale, Salt Lake County, Utah. Midvale (population 10,000) is part of the Salt Lake City metropolitan area (population 936,000). Between 1902 and 1971, United States Smelting, Refining and Mining Co. smelted ores on the site to produce copper, gold, lead, and silver. Figure 1 shows a picture of the historical Midvale smelter operations. [ ] When operations ceased, the site was estimated to contain 2 million tons of slag from these operations. The smelter no longer exists. In 1971, Valley Materials, Inc., acquired the site to process the slag into materials for railroad beds and asphalt highways. During the 1980s, the U.S. Environmental Protection Agency (USEPA) raised concerns regarding environmental impacts associated with the historical site operations. The Midvale Slag Superfund Site was listed on the NPL in 1991. The Site consists of two Operable Units (OUs): OU1 covering the properties north and adjacent to former ore smelting operations; and OU2 covering the smelter site itself. OU1 had historically been affected by wind blown slag dust and stack emissions occurring on OU2 and the Sharon Steel site further to the south. These emissions resulted in elevated levels of arsenic and lead in the native soils. The EPA issued the final Record of Decision (ROD) for the OU1 Site in 1995. The OU1 ROD required the implementation of institutional controls for the undeveloped portions of OU1 in order to restrict future land use to commercial/industrial purposes unless additional remediation was performed. Hence, the land comprising OU1 was originally considered in the ROD to be suitable for commercial or industrial purposes without the need for remedial action. However, development of OU1 for other land uses, including residential or recreational, would require additional assessment and probable remediation. The OU2 parcel was remediated by EPA to allow future land development, and the Sharon Steel site was remediated by EPA and deleted from the NPL. PROPERTY TRANSACTION AND REDEVELOPMENT In February 2006, a private development company, Mercer Bingham Junction, LLC. (MBJ) purchased 130 acres of the OU1 property for the purpose of performing environmental remediation, and developing mixed residential and commercial real estate. Development of the property was conducted in cooperation with USEPA Region 8 (EPA), the Utah Department of Environmental Quality (UDEQ) and Midvale City. The guidelines under which residential development could occur were defined by EPA. The 130 acres was to be developed for open space, residential and commercial use as part the Midvale City Bingham Junction development. Figure 2 shows the general layout of the proposed land uses. [ ] In May 2005, MBJ began pre-acquisition due diligence activities to purchase the 130 acres of OU1 north of 7200 South Street, which now comprises the Bingham Junction Development. This included the completion of Phase I and limited Phase II investigations. The Phase II investigations were performed to evaluate arsenic and lead concentrations in the planned residential areas of the site, and to explore the contents of the historic landfill on the property. The historic landfill area was on the far west side of OU1, adjacent to the Jordan River. Soil samples collected during the Phase II investigation showed that the planned residential parcels did not currently meet the criteria established in the Tech Memo and that additional placement of fill or soil excavation would be required for residential development in this area. An evaluation performed by the previous owner of the property, Littleson, Inc., showed similar results.

Jan 1, 2009