Search Documents

By D. D. Harbuck

To decrease reliance on foreign sources for the strategic and critical metals gallium and germanium, the U.S. Bureau of Mines identified and developed processing technology for two domestic sources of these metals: a Tennessee zinc residue and a Utah ore. Sulfuric acid (H2S04) solutions were used to solubilize gallium and germanium in both sources. Statistically designed experiments showed that the most important parameter for high metal extraction from zinc residue was the H2S04 concentration. At a concentration of 2.9M H2S04, 95 pct of the gallium was extracted, and at a concentration of 0.6M H2S04, 73 pct of the germanium was extracted. Controlled H2S04 concentration was also the key for high metal extractions (97 pct Ga, 87 pct Ge) from the Utah ore. Such control was achieved using a two-stage countercurrent leach circuit. Testing showed that the insoluble germanium in both the residue and ore was tied up with silica. Several methods for overcoming this problem are given. To recover gallium and germanium from the leach solutions, the solvent extractants octylphenyl acid phosphate (OPAP) (for gallium) and LIX 63-OPAP (for germanium) were identified. These extractants were tested in separate, continuous, solvent-extraction circuits yielding a gallium recovery of 94 pct and a germanium recovery of more than 90 pct.

Jan 1, 2010

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By R. Reed von Gal

The majority of zinc strip produced in the world today is cast on the Hazelett twiri-belt continuous casting machine. Ten of these machines are currently operating worldwide, and one machine is under construction for the People's Republic of China. The caster, which was first patented in 1947, was originally developed for aluminum and copper alloy casting. In the early 1960s, the design was expanded into zinc casting and within ten years the industry had essentially converted from casting and rolling ingots to twin-belt continuous casting with in-line rolling. The casting process employs two parallel, moving. water-cooled belts as the major mold surfaces. Together with two strings of side dam blocks, the design offers a four-sided moving mold which produces a continuous strip or bar. This paper will cover a bit of, the history, as well as the current technology surrounding this high production process for zinc strip production.

Jan 1, 1990

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By H. R. Manouchehri

"Pyrrhotite (Po) is one of the most abundant sulfide minerals in processing industry and must be rejected in most cases. Particularly, Po rejection and its selectivity against pentlandite (Pn) have long been a challenge due to similarities in the mineral composition of the two minerals and the collectorless flotation characteristics of Po. Xanthates have been widely used to promote sulfide mineral flotation; however, in the presence of xanthates, the redox potential established at the mineral/solution interface is most important, determining the flotation performance. In this paper, the importance of electrochemistry in Po and Pn flotation has been demonstrated and a comprehensive study was conducted on two different feed streams (i.e., magnetic concentrate and scavenger cleaner streams, containing magnetic and nonmagnetic forms of Po, respectively), from Vale’s Clarabelle Mill in Sudbury, Ontario, with an objective to determine if improvements in Po rejection and Pn recovery could be achieved by controlling pulp electrochemistry. By conducting a series of flotation tests under different Eh conditions and reagent usage schemes, it was revealed that higher Po content in the magnetic stream may protect Pn from being oxidized, improving Pn recovery. The results indicated that at low oxidizing pulp chemistry, the rest potential for the Pn is still high enough to allow the formation of dixanthogen to promote its flotation. Using a Pt electrode, it was found that by controlling pulp potential at -50<Eh< +50 mV, the Pn recovery and Po depression would be satisfactory. The results, using mineral electrodes (Outotec Chena analyzer), indicated that selective separation can be achieved if low-to-moderate oxidation potentials (0 to 100 mV) or reduction (0 to -100 mV) potentials are monitored using Pn and Po electrodes. Mixing two streams at 50:50 wt % would be possibly beneficial in selective separation.IntroductionPyrrhotite (Po), Fe1-xS, is one of the most abundant sulfide minerals in the processing industry. It is an iron-deficient sulfide that occurs either in monoclinic or hexagonal form. The monoclinic one is richer in sulfur and is ferromagnetic, whereas the hexagonal Po is poorer in sulfur and has no magnetic properties. In general, the ferromagnetic properties of natural Po increase with increasing sulfur content. Although Po holds significant iron content, it is not used as a feedstock for the iron and steel industry due to the difficulty in achieving complete removal of sulfur. The common availability of iron oxide ores makes the iron sulfides irrelevant for the steel industry."

Jan 1, 2015

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors&apos; structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors&apos; reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

By John S. Carman

Our industry is in trouble. Real trouble. It has never been an easy, secure business. But to-day it is engulfed in revolutionary currents. No longer can there be reliance upon the checks and balances of market forces. Supply and demand largely dictated the economics of business enterprise in simpler days. To-day politics, in particular nationalism become increasingly dominant. And as governments expand and put out tentacles of interference in the direction of the mining industry, far too little understanding is evidenced as to how that industry works. Then there is something which is relatively new -stagflation. As the prices of minerals falls, the capital investment required for new extractive facilities soars at rates which far outdistance those which are cited by governments to indicate the magnitude of inflation. To illustrate; 1) In 1971 it was calculated that $355 million would be required to bring the Cuajone property in Peru into production. Five years later that stage was reached at a cost of $680 million. 2) With the Caridad mine in Mexico, estimated capital investment doubled between 1971 and 1976. 3) The requirements calculated for Cerro Colorado in Panama have risen in two years from $560 to $800. 4) The budget of $240 million for Sar Chesmeh in Iran in 1971 had become $500 million by 1976.

Jan 1, 1977

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

Argentina follows Venezuela and Mexico as the largest producers of crude petroleum and natural gas in Latin America. Argentina 1S practically self-sufficient in fuels, but relies substantially on imports for its supply of copper, iron ore, ferroalloys, sulfur, and fertilizers. Mining activity is limited and is in an incipient stage of growth, considering the country&apos;s potential for mining. Most nonfuel mineral output in 1979 consisted primarily of minerals used for construction, while only 9% are other nonmetallic, and 2% are metallic minerals. Argentina is Latin America&apos;s major producer of boron minerals and uranium (yellow cake). Mineral exports consist primarily of borates, uranium concentrates, and of late, some tin. These exports have in the past been shipped mostly to Great Britain. London banks have been involved in arranging financing for St. Joe Minerals Corp. IS planned development of the El Pachon copper deposit (see map), and were being counted upon to also back the development of large copper and manganese projects. The following is a review of Argentine mineral production in 1979: (For 1981, the production of boron minerals is put at 167,000 metric tons and uranium at 300,000 metric tons.)

Jan 1, 1982

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 &apos;s the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991

By Adeyemi Adesina, Subhabrata Mishra, Syed Mohammed Mustakim, Malaya Kumar Jena, Shaswat Kumar Das

Utilization of low-grade manganese ore adopting the carbothermic reduction roasting process is a proven method to produce high-grade manganese ore. To minimize industrial waste and protect the environment, gas cleaning plant sludge (GCPS), which is a solid waste from steel industries, was employed as a reductant to perform the reduction roasting process. The optimum conditions to carry out reduction roasting of the low-grade manganese ore were found to be: a roasting temperature of 950 °C, a residence time of 2 h, 40% GCPS as reductant, and magnetic separation at 5000 G for a manganese ore size of –10 mm. A lowgrade manganese ore comprising Mn grade 31.27% and Fe grade 19.78% having a Mn/Fe ratio of 1.58 containing a high silica content of 26.48% was used for the carbothermic reduction roasting having mineral phases of pyrolusite (MnO2) and hematite (Fe2O3) as found from XRD. The gangue minerals were separated during the magnetic separation, and the upgraded product was obtained, which reached a maximum value of TMn 49.5% with RMn 76.55% and TFe 62.19% with RFe 42.51%. In the study, activated charcoal (AC) was also taken as a reductant for comparative analysis; the experimental results revealed that GPCS performed better than that of the AC, showing potential to be used as a reductant in metallurgical industries. However, the resultedMn/Fe ratio was very low for the reduced sample; therefore, it can be used for smelting along with high-grade manganese ores as a feed.

Mar 5, 2021

By G. S. Scott

[The Duretiu of Kinen, as :) pr<r"Yof its :;encr:rL propan clealini: with the causes, behavior, n.ncl tor-trol of o1:t1?;.?cite-mine fires, hns investic:&apos;lte3 I varionr. Te:.nr, for Je tec tin:: iccj.r)ic:~ t he;, tint; :,:.zqdergro-.:rid and of <~e termining the trend of the hen tir..: once -I i&apos;i re j 7 knnm tr, he nrcsc~t.]

Jan 1, 1938

By G. S. Scott

[The Duretiu of Kinen, as :) pr<r"Yof its :;encr:rL propan clealini: with the causes, behavior, n.ncl tor-trol of o1:t1?;.?cite-mine fires, hns investic:&apos;lte3 I varionr. Te:.nr, for Je tec tin:: iccj.r)ic:~ t he;, tint; :,:.zqdergro-.:rid and of <~e termining the trend of the hen tir..: once -I i&apos;i re j 7 knnm tr, he nrcsc~t.]

Jan 1, 1938

By R. G. K. Morrison

By arrangement between the Ontario Mining Association and Messrs. John Taylor & Sons, Mining Engineers, 6 Queen Street Place, London, E.C.4, the writer was engaged for a period of not more than three months to report on the rockburst situation in Ontario mines. This was later amplified, by mutual agreement, to include, at the expense of detail, visits to the larger camps where rockbursts had not occurred, to get a general picture of conditions and to discuss the subject with operators in their respective areas. Scope of Activities Visits were paid to the following properties for the purpose of enquiry and discussion; the underground workings of those mines marked with an asterisk were visited on one or more occasions: KIRKLAND LAKE * Macassa Mines, Limited * Kirkland Lake Gold Mining Co., Ltd. * Teck-Hughes Gold Mines, Limited * Lake Shore Mines, Limited * Wright-Hargreaves Mines, Limited Sylvanite Gold Mines, Limited Toburn Gold Mines, Limited EAST KIRKLAND & LARDER LAKE Upper Canada Mines, Limited Chesterville Larder Lake Gold Mtng Co., Ltd. Kerr-Addison Gold Mines, Limited Omega Gold Mines, Limited PORCUPINE * Hollinger Consolidated Gold Mines, Ltd. * Mcintyre Porcupine Mines, Limited * Dome Mines, Limited * Buffalo Ankerite Gold Mines, Limited Paymaster Consolidated Mines, Limited Preston East Dome Mines, Limited Pamour Porcupine Mines, Limited Broulan Porcupine Mines, Limited Hallnor Mines, Limited Naybob Gold Mines, Limited Delnite Mines, Limited Moneta Porcupine Mines, Limited DeSantis Porcupine Mines, Limited Coniaurum Mines, Limited SUDURY lnternational Nickel Co. of Can., Ltd. * Falconbridge Nickel Mines, Limited LITTLE LONG LAC AREA * Little Long Lac Gold Mines, Limited MacLeod-Cockshutt Gold Mines, Ltd. Hard Rock Gold Mines, Limited Bankfield Consolidated Mines, Limited Magnet Consolidated Mines (1936), Ltd. à PICKLE LAKE AREA * Central Patricia Gold Mines, Limited * Pickle Crow Gold Mines, Limited UCHI LAKE * Uchi Gold Mines, Limited McKENZIE ISLAND AREA Gold Eagle Gold Mines, Limited * McKenzie Red Lake Gold Mines, Ltd. * Cochenour Willans Gold Mines, Limited RED LAKE * Howey Gold Mines, Limited Hasaga Gold Mines, Limited Madson Red Lake Gold Mines, Limited

Jan 1, 1942

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

As the chief field of the gold dredging industry in Otago is the district traversed by the Molyneux River (called above Cromwell the Clutha) and its tributaries, a brief reference to the geology of that region and the origin of its alluvial gold will not be out of place. The prevailing rocks are metamorphic schists, chiefly mica and quartz schists, pr.obably of Silurian age. Though these rocks do not contain many payable quartz reefs, gold appears to be distributed in small quantities all through them,chiefly associated with the quartz lamime and lenses. The river drift, however, contains numerous pebbles of quartzite, quartzoze conglomerate, and fme-grained slate. Seeing that these rocks are hardly known to occur in situ within the watershedof the Molyneux River, though Devonian and carboniferous rocks of similar character occur to the north-east and south-west, it seems probable that the schists were at one time overlaid by carboniferous and Devonian rocks, and that these have been removed by denuding agencies. Be this as it may, it is certain that the schists themselves have been greatly eroded by the action both of water and of ice, and that the resulting drifts have themselves, in many cases, been sorted and re-assorted by the same agents.Consequently the drifts are very varied in character and often developed on a grand scale. In geological age they vary from Early Tertiary (though some may be older) to Recent.

Jan 1, 1903

By A. J. Martin

The Tri-State, or Joplin, zinc and lead mining district in south- western Missouri and adjoining, parts of Kansas and Oklahoma is one of the great mining districts of the world. It is in flat-lying or gently rolling agricultural country near industrial centers and coal, oil, and gas fields. The nearly horizontally, lying bedded rocks in which the ore bodies are found were originally limestone but are now largely chert containing minor percent- ages of dolomite and other minerals. The ore occurs in nearly vertical fis- sure zones, large and small, and in blanket (sheet-ground) deposits. The mining depth ranges from surface diggings to $50 feet. The average tenor of the ore mined, in recent years is much lower than that of ore produced in other large zinc and lead districts of the United States. Mining and mill- ing costs are low because of the shallowness of mining, amenability of ores to concentration, efficiency resulting from long experience of management and labor, and other factors. The operators comprise many small and medium-size producing companies and partnerships, as well as individuals and a few larger producers. About 7,000 men are employed in the mines and mills during normal industrial activity. The concentrates produced are sold f.o.b. the mill bins to local representatives of smelting companies at prices quoted on the Joplin market. The productive life of the district began with the discovery of lead near Joplin in 1848, but output was not large until after mining for zinc began near Granby in 1871. In most of the intervening years through 1945 the district produced more zinc than any other field, and it generally ranked third or fourth in the United States in lead production. Figures compiled from sources given later in this paper show a total output for the district from the beginning through 1945 of 20,755,020 tons of zinc concentrates and 3,334,057 tons of lead concentrates valued altogether at $1,110,058,581 in the mill bins. The output, in terms of recoverable metals, was 10,609,408 tons of zinc and 2,529,121 tons of lead, valued in all, at the average yearly market prices of the metals, at $1,691,282,419. During the 39 years (1907-1945) for which complete figures are available, the annual output of the district fluctuated from 23 to 66 percent of the total United States mine output of zinc and from 5 to 18 percent of the total lead; the averages for the period were 40 percent for zinc and 11 percent for lead. peak yearly production was attained in 1926, with an output of 423,800 tons of recoverable zinc and 102;117 tons of lead. Since that yoar the production rate has trended downward, accentuated at first by the depression in the thirties and later ameliorated somewhat under the stimulus of heavy demand and higher metal prices during World War II; the output in 1945 was 139,274 tons of recovorablo zinc and 23,556 tons of load. The above figures show the groat contribution made by the Tri-State district in the past toward the country's supplies of primary zinc and lead, cspecially zinc. However, the district's production is expected to decline both in quantity and in proportion of total United States mine output unless important discoveries are made. Ore exposed in mine workings and extensive exploratory drilling done in recent years within and without the productive The

Nov 1, 1946

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By H. W. Gillett

This bulletin is issued by the Bureau of Mines as a contribution to the increase of safety and efficiency in the preparation and utilization of the mineral resources in the United States. Notable among the drains on these resources are the demands made by the nonferrousmetal industries, and in these the losses occasioned in melting brass and bronze are worthy of particular attention. This statement will be better appreciated by a consideration of the size of the brass industry. MAGNITUDE OF THE BRASS INDUSTRY. According to the Thirteenth Census, in 1909 there were in the United States 1,021 fu-ms that dealt mainly in brass and bronze. This total included jobbing foundries, manufacturing plants that both cast and machine a brass or bronze product, and rolling mills, but did not include iron foundries having nonferrous departments nor the numerous large brass-foundry departments of manufacturing plants that produce the castings used in the manufacture of electrical apparatus, cash registers, pumps, and the thousands of machines that require brass castings for their construction. Penton&apos;s Foundry List for 1910 gives about 1,150 exclusively nonferrous foundries and about 2,300 iron or steel foundries that also melt brass. If the rolling mills and. jobbing foundries in manufacturing plants be included, and if due credit be given to the rapid growth of the industry in the last few years, largely through the stimulation of the automobile busi¬ness, it is probable that not less than 3,600 plants are to-day melting brass or bronze.

Jan 1, 1916

By Joseph J. Wallace

The 1952 Annual Report of the West Virginia Department of Mines lists seven beds that are being mined in Mingo County, of which the Cedar Grove is the most important. The Cedar Grove, Alma, and Coalburg contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 3,007 million short tons as of January 1, 1953. Of this total, 2,396 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954