Search Documents

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the Panzhihua low grade ilmenite and graphite were milled for 1, 2, 4 and 8 h firstly, then the temperature rising behavior of milled sample in microwave field were studied. The average heating rate of samples milled for 1, 2, 4, 8 h were 1.86, 4.08, 2.82, and 2.32 K/s; Before optimize the microwave reduction process, several experiments were conducted in order to confirm the parameters range. After milled for 4 or 8 h and reduced above 930 oC, the Fe metallization are higher than 90%; Then the optimization was investigated by using response surface methodology (RSM), the significance of predict model and each terms were analyzed, and the optimization parameters were given as: milling time is 4 h; reduction temperature is 1001 or 1070oC; the holding time is 37.5 or 26.9 min. Under these conditions, the Fe metallization given by predict model is 91 or 92 %.IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposits in Panzhihua, China. In this reserve, there is about 8.73×108 t of TiO2, accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [1] Titanium mineral deposits are classified into Rock type and Placer type. Rock type is the igneous mineral, which have high content of FeO (Relative to Fe2O3) and gangue. The Panzhihua ilmenite is a typical rock type ilmenite ore. The higher contents of MgO, CaO, SiO2 and the complex mineralogy are making its direct reduction progressively more difficult."

Jan 1, 2011

By P Shen, K Hattori, H Pan, E Seitmuratova

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore-bearing intrusions in the Central Asian Orogenic Belt (CAOB) were examined from nine mines: Boshekul, Nurkazgan, Kounrad, Borly, Aktogai, Koksai, Baogutu, Tuwu and Erdenet. The intrusions are diorite, granodiorite and tonalite with SiO2 contents ranging from 58 to 75 wt per cent, and show mildly fractionated rare earth elements (REE) ([LREE]N/[HREE]N = 2.7–4.7) – light REE and heavy REE – and varying Eu anomalies ([Eu]/[Eu]* = 0.58–1.4). The ratios of Sr/Y vary from 7.9 to 115 and the contents of Y from 4.6 to 23.9 ppm. The parental magmas of the intrusions are intrinsically oxidised. Zircon grains in the ore-bearing rocks from large- and intermediate-sized porphyry Cu deposits show high Ce4+/Ce3+ ratios characterised by 65–422 at Boshekul (>4.1 Mt Cu), 76–480 at Kounrad (>4.8 Mt Cu), 90–280 at Aktogai (>12 Mt Cu), 80–250 at Erdenet (>11 Mt Cu) 74–370 at Nurkazgan (>3.9 Mt Cu), 100–210 at Koksai (>1.6 Mt Cu), and 71–340 at Tuwu (~2.0 Mt Cu). In two small deposits, the ore-bearing rocks display low values of Ce4+/Ce3+; Borly (0.6 Mt Cu) ranging from 28 to 158, and Baogutu (0.6 Mt Cu) from 29 to 113. The Ce4+/Ce3+ ratio of 120 distinguishes large intermediate-size deposits from small-size deposits. This information is potentially useful in exploration for porphyry Cu deposits in the belt.CITATION:Shen, P, Hattori, K, Pan, H, Jackson, S and Seitmuratova, E, 2015. Granitoids associated with porphyry Cu deposits in the Central Asian Orogenic Belt – characteristics and oxygen fugacity, in Proceedings PACRIM 2015 Congress, pp 377–382 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By David E. Van Dillen

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, axisymmetric and plane joint, and a three-dimensional joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1981

By AIME

IN the parlance of Hollywood, it was a super-colossal meeting. In the more restrained language of engineers, the Institute's 75th Anniversary Celebration attracted the largest crowd ever; was the longest Annual Meeting ever held, occupying a full week; had more important papers, more important people, more of an international flavor, and more glamour than ever before. And in the minds of those who came to the big city from the wide open spaces, one other record should be mentioned: for those not on an expense account, it was the most expensive affair ever staged by the Institute! To state the attendance down to the last digit for a meeting such as this is impossible. The total names registered on cards, plus those who attended the Annual Banquet but were not otherwise registered, came to 3149. But a few were registered twice, and probably a still larger few did not register at all, but just dropped in for a session or two in which they were interested. It would appear that 3200 would be about as close an estimate of attendance as could be made, and that is some 300 more than came to the biggest Annual Meeting of the past-in 1944. A considerable number of members brought their wives, but most were delegates at large.

Jan 1, 1947

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers fromthe National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand, and gravel mine sites throughout the USA. A primary purpose of these interviews was to verify the competencies included in the hazard recognition competencies framework and to understand why these competencies are critical. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

Jul 27, 2020

By C. S. Gibson

"MOST of the mines in the Province of Ontario in Canada are multi-level operations in steeply dipping veins; yet there is an appreciable number whose de-posits are relatively flat-lying, ranging up to 45° inclination.The veins vary in width up to several hundred feet and may or may not be branching systems. The depths of mines range from a few hundred to 8,000 feet, approximately. The primary products of the underground group are asbestos, gold, silver, cobalt, copper, nickel, iron, uranium, talc, fluorspar, gyp-sum and salt.There are a few open-pit mines. The majority are temporary in type because, as the outcrops are removed, mining is continued be-low surface. Primary products of the open pits are copper, nickel, iron, magnesium and nepheline syenite.The industry as a whole employs about 50,000 persons, approximately 60 per •cent of whom have dust-exposure occupations. The definition of a dust-exposure occupation and the requirements for •dealing with same are set forth in The Mining Act of Ontario.Results of extensive and continuing studies on the incidence and progression of silicosis have been reported periodically for years past, in annual reports of the Mines Accident Prevention Association of Ontario and in papers presented at Conferences sponsored by Mcintyre Research Foundation of Toronto, all of which have been published. The information provided therein proves the effectiveness of the means being used to prevent silicosis and allied disorders."

Jan 1, 1960

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By G. C. Marino

The performance of the V-Day Mine near Danville, Illinois has been evaluated from data extending over about a 20 year period. The area included in this study involves over 16 acres. Essentially this entire area has progressively subsided. Extensive data has been collected on the geologic and mining conditions, the subsidence movements, as well as on the response of the surface structures to the subsidence. In this paper a detailed summary of the site conditions is given, and the mechanics of progressive failure of the studied room and pillar mine is postulated. These progressive long-term failures of the V-Day are then compared to other similar mine failures in Illinois. Some overall, but tentative, long-term strength evaluations are presented as well.

Jan 1, 1990

By Jos. R. Guiteras

This paper describes the operations of the St. Joe Mining & Milling Co. in Boulder County, Colo., as of June 1936. Later a brief visit was made to the mine in September 1936; information obtained at that time has also been recorded. The company operates a gold mine, the Grand Republic, in the Sugar Loaf mining district; a 100-ton flotation mill in Lefthand Canyon near Gold Hill; and a custom sampling punt, the Boulder Ore Sampling Works, at Boulder, Colo.

Jan 1, 1937

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Manuel Gomez

Low-temperature carbonization product yields for 129 coals representative of 12 Utah coalfields were estimated, using regression equations developed from heating value and proximate and ultimate analysis data. It was shown that yields of char, tar plus light oil, water of decomposition, and gas, as well as the gas volume and the heating value of the gas, could be predicted with reasonable accuracy. Published and experimental results from eight Utah coals carbonized at selected temperatures in the 4500 to 1,000° C range were used to determine the effect of temperature on product yields. Carbonization temperature, heating value) oxygen, and volatile matter of coal appear to be the principal variables influencing carbonization product yields. Data presented show that the heating value and the residual volatile matter in low-temperature char may be predicted using relationships developed from proximate analysis data for 220 coals.

Jan 1, 1967

By CLARENCE G. SMITH

Prior to the actual development of an oil property it is difficult to determine the quantity of oil under the property and the rate at which this oil can be brought to the surface-factors that determine the ultimate value of the property. Consequently, there has been much confusion in devising accounting systems that, during the entire life of a property, will show costs and profits from which the producer can determine whether his property is being worked at a profit or otherwise. The Bureau of Mines publishes this report in recognition of a distinct need for a simple treatise on accounting methods adapted to the peculiarities of the petroleum industry. Probably many companies operating oil wells are not fully acquainted with details important to the welfare of their business, because their account books fail to furnish them with exact and adequate data. With the accountant rests the responsibility of providing the management with reports setting forth the details of the business expressed in fitting terms as well as in dollars and cents. These reports are a means whereby efficiency may be maintained, waste prevented, oil obtained and sold, and money suitably reinvested. They also enable a concern to study the progress of its business in order to conserve to the utmost the possible benefits from an exhaustible deposit of mineral wealth. When managements realize the extent of the waste at their properties more attention will be given to the character of the accountancy records. Herein are presented descriptions and discussions of balance sheets, profit-and-loss statements, and bookkeeping methods peculiarly adapted to the oil business. As far as possible, technical phrases have been omitted in order that those not familiar with accounting terms may be able to follow the subject matter. The systems of keeping books outlined in Chapter X have all been found practical. For brevity as well as clearness the major part of the work refers to the company operating only one property.

Jan 1, 1917

By Jos. R. Guiteras

This paper has been written to describe briefly the mining and milling of gold and silver ores in the Black Canyon and neighboring mining districts in Yavapai County, Ariz. The description of present operations is the result of a 10-day visit to the region by the writer in March 1936. Acknowledgments The author is indebted to earlier writers on the geology and mining in this regions and to the mine managers and their staffs, whose courteous cooperation has made possible the assembling' of material for this paper. Individual acknowledgments are made in the text.

Jan 1, 1936

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By Steve Karl

Introduction Technological advances in mining and processing have started the domestic mining and mineral industry back on the road to competitiveness. A massive trade deficit, however, coupled with foreign competition and more government regulations threaten to slow this recovery. So say mining executives in Colorado and Minnesota. These industry decision-makers agree that their challenge is to continue the technical innovations of their industry. The journey back to profitability and competitiveness means improved products, they say, but at lower production costs. At separate gatherings in January, officials in both states said that they believe their industry is up to the challenge. Worker attitudes will have to change, they understand, and management styles will need adjusting. And, while they are willing to make the necessary adjustments, they are going to need some help. Or, at the very least, less interference from the federal government. Foreign markets, all but closed to American products, must be opened up on a reciprocal basis. The nation's $170 billion trade deficit is a priority item that can no longer be ignored. And, closer to home, federal and state environmental regulations concerning mineral production must themselves be monitored. 1987 in Colorado While Colorado's service and trade industries should have a fairly good 1987, the state's mining industry can expect another disappointing year filled with layoffs and declining profits, according to the Colorado Mining Association. Once again, foreign competition and government regulations are seen as the main reasons for the mineral industry's woes. And state mining officials see little relief until at least the 1990s. Speaking to a group of reporters at its annual press briefing in Denver, CMA officials said Colorado's overall nonfuel mineral production is expected to fluctuate between a flat and declining growth trend. Mining employment in the state is expected to fall by 400 people this year, to about 7500. In 1981, Colorado mines employed as many as 17,800 people. During the 1970s and early 1980s, the employment rate in mining in the state grew by 12% annually, according to a summary report compiled by the CMA. Last year, worldwide molybdenum production continued to exceed demand US moly producers, therefore, were forced to continue their familiar path of production cutbacks, as well as workforce reductions. And some molybdenum mines in the US closed altogether, the CMA report stated. In Colorado, Amax's Climax and Henderson molybdenum mines operated at about 50% of combined capacity. Climax employed about 200 people at the beginning of 1987, producing about 5.4 kt/d (6000 stpd) or ore. Henderson employed about 700 people, producing about 24.5 kt/d (27,000 stpd) of ore. In coal, the number of licensed coal mines in Colorado has declined from 124 in 1960 to 43 in 1986, of which only 23 were producing. Once a stable source of employment and production, the metallurgical coal industry in the state has only one surviving metallurgical coal mine, Mid-Continent's Orchard Valley mine. High production and transportation costs, weakness in the US steel industry, and a weak market position have contributed to the decline, the summary reported. "The challenge facing most mining companies in the United States today is to survive," said

Jan 3, 1987