Search Documents

By Miguel N. Herrera

The electrochemistry of coal pyrite is relevant to coal desulfurization by chemical or bacterial leaching, flotation and oil agglomeration. The electrochemical behavior of polished and etched Upper Freeport and Pittsburgh coal pyrite samples was investigated from pH 1.0 to 10.5. The open-circuit potentials decreased with increasing pH, as expected, but were well above the thermodynamic stability region of pyrite, and decreased with time. Cyclic voltammetry revealed behavior highly sensitive to pH and scan rate (2.0 and 20.0 mV/s). The behavior on the first cycle was always substantially different from that on subsequent cycles. The anodic and cathodic reactions were correlated with the Eh-pH diagram for the Fe-S-H20 system to identify the reactions occurring at different pH values. There was also evidence that the buffers used to maintain basic pH values are themselves electrochemically active, which should be considered in interpreting many earlier electrochemical studies of sulfide minerals.

Jan 1, 1994

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By Charles H. Buclmam

"Environmental regulatory requirements for discharge of solutions and closure of operations for the gold mineral processing industry have been gradually lowered and in certain instances have been targeted to USEP A inorganic drinking water standards for dissolved ions in solution. The use of jar tests for water treatment process development is suitable for preliminary scoping work to be conducted in the research laboratory, as well as for optimization studies at the site of the treatment requirement. This paper will describe experimental methods which were performed using standard jar test equipment in efforts to produce solutions which meet USEP A inorganic drinking water standards after chemical treatment of cyanide solutions. The materials tested included gold bearing pregnant solutions from heap leaching operations, gold plant barren solutions from the Merrill-Crowe zinc cementation gold recovery process and gold heap leach wash solutions after carbon-in-column gold recovery. Experiments included cyanide destruction with sodium hypochlorite and arsenic and selenium co-precipitation coupled with mercury precipitation.IntroductionCyanide leaching solutions are used to selectively dissolve metallic gold from commercially viable mineral deposits. The heap leaching process involves stacking of gold bearing ores on specially designed solution containment pads and percolating alkaline cyanide solutions through the ore to dissolve the gold. Pregnant solutions containing the dissolved gold are collected and sent through a gold recovery process. After selective recovery of the gold, the barren solutions are recycled to the gold extraction process after adjustment of the solution alkalinity and available cyanide concentrations."

Jan 1, 1997

By Shenghui Guo, Jianbo Lan, Hongying Xia, Jinhui Peng, Lihua Zhang, Libo Zhang

Spent Hawaii nut shell was converted into a high-quality activated carbon via steam physical activation. Analysis of the experiment including activation temperature, activation duration, steam flow rate on the adsorption capability and yield of activated carbon were identified. Response surface methodology showed that the activation temperature was identified as 866 , an activation duration of 36 min and a steam flow rate of 2.5mL/min with the methylene blue adsorption number of 195 mg/g and yield of 77.75%. The key parameters that characterize quality of the activated carbon such as the BET surface area, total pore volume and average pore diameter were estimated to be 1125m2 /g, 0.94mL/g and 5.21 nm, respectively. Additionally, by the SEM analyses of char and activated carbon, the surface of activated carbon has large number of pores of irregular and heterogeneous morphology.

Jan 1, 2016

By Shane Andrews, Gustavo Vasquez, S. K. Varma

"The effect of solutionizing time on the corrosive wear behavior of 2014 aluminum alloy has been studied using the impact and continuous mode of scratching techniques. The transient currents (TC) evolved during the scratching of the alloy shows a linear dependence between the TC and the solutionizing time. Higher TC values at longer solutionizing time may be associated with the changes in the concentration of quenched-in vacancies, grain sizes and dislocations generated during scratching. These factors can either create (a) anodic sites or (b) pitting corrosion resulting in the generation of transient currents. The results have been compared with the similar study carried out for 6061 aluminum alloys. This 6061 aluminum alloy shows similar behavior but the rate of TC generation per unit solutionizing time is much lower than 2014 aluminum alloy. The morphological changes in the impact scratches and the TEM investigation in the scratch have been presented in this paper.IntroductionThe technique of studying corrosive wear of composites of 6061 aluminum in the monolithic and reinforced forms has been reported in the literature [1]. Two modes of scratching, consisting of impact and continuous, in a corrosive environment indicate that the composites, containing 0.10 and 0.20 volume fractions of alumina particles (VFAP), have higher corrosive wear rates than the monolith. A graph between the transient current (TC) generated during the impact scratching as a function of solutionizing time at 540°C indicates linear relationship between them. A similar slopes for the composites were observed and the TC values were less for the composite containing lesser VFAP."

Jan 1, 1998

By Roderick I. L. Guthrie, Donghui Li, Mihaiela Isac, Luis Calzado

The HSBC is an ideal process for the production of BMG strips. The purpose of the present work was to investigate the casting of Ca-based, bulk amorphous strips. The possibility of casting three Ca-based alloys (60Ca-20Mg-20Al, 60Ca-15Mg-10Al-15Zn and 55Ca-15Mg-10Al-15Zn- 5Cu (at.%).) was investigated, using the HSBC simulator. Numerical simulation and mathematical modeling were used to predict temperature variations and cooling rates, under different interfacial gaseous atmospheres (helium and air) near the meniscus region. Given the critical cooling rates and glass temperatures needed to be reached for the vitrification of the respective alloys, this leads to predictions of the critical thicknesses possible with this novel casting process. To validate our predictions, these alloys were then prepared and cast onto the sand-blasted, solid copper substrate mould of the HSBC simulator. The possibility of producing Ca-based metallic glassy strips via the HSBC processes was confirmed, using optical microscopy, X-ray diffraction and Scanning Electron Microscopy, to characterize the glassy properties of the cast strips. It was found that the HSBC process would be able to provide sufficient cooling to form amorphous strips for the 60CA-15Mg-10Al-15Zn and 55Ca-15Mg- 10Al-15Zn-5Cu alloys, but not the 60Ca-20Mg-20Al alloy.

Jan 1, 2014

By I. B. Scorzelli

The aim of this paper is to make a detailed mineralogical characterization of a typical brazilian xenotime and zircon from the Pitinga Mine using SEMIEDS techniques, On the other hand, superficial pretreatments with HCI, HN03 and HF were done to evaluate the modifications on surface compositions and the morphology of the particles for flotation purposes, The studies showed that both xenotime and zircon present very small inclusions of thorite; zircon is strongly metamictizated given rise to malacon. The HF pretreatment deeply affected the morphology of the particles as well as the surface properties in relation to flotation.

Jan 1, 1996

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986

By Tom Lewis

This report discusses the evaluation of the ENVIRO-CLEAN PROCESS, a technology developed by Lewis Environmental Services, Inc. for the recovery of metals such as chromium, mercury, copper, cadmium, lead, and zinc from surface and groundwater streams. This new heavy metal removal process (patent-pending) utilizes granular activated carbon with a proprietary conditioning pretreatment to enhance heavy metal adsorption combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA limits. A 50 gpm system was installed for recovering hexavalent chromium from a ground water stream at a site located in Fresno, California. The effluent from the activated carbon system was reinjected into the ground water table with the hexavalent chromium concentration < 10 ppb. The system simultaniously removed trichloroethylene (TCE) to concentrations levels < 0.5 ppb. The activated carbon is regenerated off-site and the chromium electrolytically recovered. The full scale system has treated over 5 million gallons of ground water since installation.

Jan 1, 1996

By Alicia Esther Ares

This study was conducted to investigate the directional solidification of Zn-20%A1 and Zn20% A1-1O%Si-3o/oCu alloys under different conditions of heat transfer at the metal/mould interface. The type of structure obtained in both cases was analyzed and related to the solidification thermal parameters such as cooling rate, growth rate, thermal gradient and recalescence which were determined from the temperature versus time curves. These parameters were correlated with the structure-like length of columnar grains and size of equiaxed grains. The metallographic analyses were done performing quantitative metallography and composition analysis of the different alloying elements along the cast samples by SEM (Scanning Electron Microscopy) and EDXA (Energy Dispersive X-Ray Analysis). Correlations between properties, structures and thermal parameters were found.

Jan 1, 2008

By Mohamed Y. Bakr, Aly M. Abdel-Rehim

The present work is related with mechanical activation of processing of Egyptian wolframite by simultaneous ball-milling and pressure alkaline leaching, to improve the recovery of tungsten from wolframite. The results show a total recovery of tungsten from wolframite (97.8- 98.7%) by simultaneous ball–milling and alkaline leaching at temperature 175-200oC. It is concluded that processing of wolframite by simultaneous ball- milling and leaching is mechanically activated and accelerated as a result of the grinding action of steel balls that caused the immediate rupture by continuous removing the product layer of the reaction ( sodium tungstate and iron and manganese hydroxides ) from reacting particle surfaces. This leads to the exposing of fresh and activated wolframite particle surfaces to alkaline leach solution and consequently the acceleration of the reaction of wolframite leaching .The results of the kinetic study 0f alkaline processing of wolframite and its mechanical activation show that the system is under kinetic control.

Jan 1, 2015

By James R. Craig

Petroleum coke is becoming an increasingly important source of light hydrocarbon products as product crudes become heavier and of poorer quality. The use of petroleum coke to generate synthesis gas results in the formation of residual slags that are enriched in silica, alumina, sulfides, oxides, and free metals. The characterization of these slags and their con? stituent phases is an essential step in considering the ultimate use or disposal of such slags and in understanding how to alter the properties of the slags to optimize the efficiency of gasifiers. Depending upon temperatures and bulk compositions, quenched slags typically consist of silicate glasses, calcium silicates, iron-nickel oxide-sulfide masses, aluminate spinels and free metals. Whereas the glasses contain relatively uniformly dispersed metals and sulfur, the iron-nickel oxide-sulfide masses highly concentrate nickel and sulfur. The aluminate spinels very effectively concentrate vanadium and chromium, thus depleting glasses or other adjacent phases. The abundance as well as the make up of the slags strongly affects the physical behavior of the slags within the gasifiers

Jan 1, 1989

By John L. Watson

The dewatering of steel industry waste sludges prior to discard or recycling often presents significant problems due to the fineness of the sludge particles, which may blind the filter medium and/or produce a cake with limited porosity, Several steel plant wastes, such as sludges from BOF and EAF gas cleaning operations exhibit not only a very fine particle size, but also some degree of magnetic character, A novel process has been developed to utilize the magnetic character of such sludges to enhance dewatering through a multi-force operation involving magnetic, chemical and vacuum forces, The process consists essentially of undertaking vacuum filtration of a flocculated sludge in a magnetic field, This is achieved by installing a permanent magnetic in a fixed position on the axis of a vacuum drum filter, thus effecting filtration of magnetic and non- magnetic particles, bound together in flocs, in a magnetic field, Previous tests using a modified laboratory vacuum drum filter treating artificial (magnetite) and industry waste (BF sludge) feeds have demonstrated that filtration capacity may be enhanced significantly with increases of up to 3000/0, An explanation of the mechanisms associated with the enhanced filtration was not obvious, and this research was undertaken to permit the cake formation in the magnetic field to be monitored to provide an insight into the manner in which particles agglomerate to form the cake. These tests revealed that the magnetic field caused magnetic particles to be aligned perpendicular to the filter surface and to form channels through which filtrate could freely pass thus increasing capacity, The effects of various magnetic fields and field strengths on the filtration process were also investigated. A simple computer model was constructed to demonstrate the proposed theory of multi-force dewatering, The model output graphically illustrated the suggested mechanism and confirmed the enhanced capacity of the novel dewatering process,

Jan 1, 1996

By L. Deininger

The QSL plant in the existing "Betzelius" Stolberg GmbH lead smelter in StolberglGermany was commissioned in August, 1990. Following some modifications to the process and equipment which had become necessary in line with the implementation of this new techno- logy, conclusive operating results are now available. These will be reported together with a short description of the plant design. In May 1992, raw material feeding to the QSL reactor in the new lead smelter of Korea Zinc Co. in OnsanlKorea was started. As all the experience gained up to that point in time in the Stolberg plant had already been incorporated in this plant prior to start-up, it reached stable, satisfactory operating conditions in a short period of time. After an introductory description of the plant important operating results will be reported. The operating experience gained in the two plants fully confirms the correctness of the in- ventors&apos; creative ideas in the 70s. The QSL process meets all demands made on modern, ecologically compatible and energy-saving lead production technology. The paper ends with suggestions on how the QSL process will be optimized further in the future.

Jan 1, 1994

By Norihiko Fukatsu, Takashi Iwamoto, Noriaki Kurita, Koji Katahira, Kunihiro Koide, Teruo Ohashi

"The galvanic cell-type hydrogen sensor employing CaZro.9Ino.t03-a. as the solid electrolyte was designed for the measurement of hydrogen activities in molten copper under industrial .conditions. The sensor probe consists of the cap-shaped solid electrolyte with porous platinum electrode on the inside and alumina refractory tube. The gas mixture of the composition 4%H2-0.5%02-Ar was made to flow on the inside electrode. The hydrogen sensor probe was inserted directly into molten copper and the melt was used as the outer electrode. The effect of oxygen activity gradient to EMF was eliminated theoretically by measuring the oxygen activity in the melt simultaneously with an oxygen sensor. The high stability of output and excellent response to the change of hydrogen activity were obtained over the wide range of industrial copper melting conditions.IntroductionIn the metal casting process, hydrogen easily dissolves in molten metals from water vapor in the surrounding atmosphere. Owing to the large difference in hydrogen solubility between liquid and solid metal, dissolved hydrogen becomes a cause of the defects of blowholes in castings or ingots. It is necessary to control the hydrogen content in the molten metals [l]. Using proton-conducting ceramics as a solid electrolyte, high temperature-type hydrogen sensor can be constructed [2]. SrCe03- and BaCe03-based perovskite-type oxides exhibit appreciable proton conduction under hydrogen containing atmosphere at high temperature [3-5]. A hydrogen sensor for molten aluminum using CaZro.91no.103-a. has been developed and widely used in the ·process control in the aluminum melting industry [6,7]. The same type of hydrogen sensor has also been expected in the copper melting industry. .. However, CaZro.91no.103-a shows ·not only proton but also oxide ion conduction in the high temperature and at low oxygen activies like the copper melting· conditions. Then we studied the oxide ion conduction in CaZro.91no.103-a. iit · detail [8]. From the consideration on the EMF of the galvanic cell employing this material as electrolyte, it was shown that the unknown hydrogen activity may be precisely determined from cell potential which is corrected for the effect of oxygen potential gradient And the hydrogen sensor based in this principle was constructed and tested in laboratory-scale [9,10]. We repeated the similar tests in factory-scale and developed the sensor system for practical uses [11, 12]. In this report, the structure and system of the hydrogen sensor for molten copper will be introduced first. The reliability of the sensor will then be demonstrated from the results of experiments for sensor probes carried out in TYK's laboratory."

Jan 1, 2000

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000

By Hector Carreon

This paper presents experimental data for the magnetic field produced by thermoelectric currents around uncracked hard-alpha inclusions in a Ti?6Al?4V specimen under external thermal excitation for different nitrogen content ranging from 1.6% to 5.9%. According to our preliminary results, the magnetic flux density measurements were found to be rather sensitive to changes in nitrogen content with the exception of the intrinsic material background magnetic signal that affected deeply the detectability of inclusions and imperfections in non-contacting thermoelectric measurements. Hopefully, these preliminary results can help identify a non-destructive test method that can detect material inclusions with a level of nitrogen that could be detrimental to Ti?6Al?4V alloy components.

Jan 1, 2009

By Y. A. Chang, J. Woodford, C. R. Kao

Reactive diffusion studies between NbC and Si were carried out at 1300 °C under a vacuum of 10-5 torr and a uniaxial pressure of 1 MPa. The annealing time ranged from 8 to 100 hours. The Si used was single crystal silicon; the NbC was hot-pressed powder compact. A NbSi2+SiC two-phase reaction layer formed with NbSi2 as the matrix and SiC as discontinuous particles. The microstructure of the reaction product is homogeneous, dense, and fine. The NbSi2 grain size and SiC particle size are in the micron range. The growth of the reaction products follows parabolic kinetics. Extrapolation of the data to zero thickness suggests an apparent incubation time of 3.5 hours. However, for short annealing time «60 hours), the thickness data can be approximated by linear kinetics with an initial growth rate of about 2 11m/hr. Based on these experimental observations, a growth mechanism for the reactive diffusion between Si single crystal and NbC powder compact is proposed. We propose that the nucleation sites for the SiC particles are at the voids of the NbC powder compact. This proposed nucleation mechanism offers a potential way of controlling the SiC particle size by changing the void size and void density of the NbC powder compact. This hypothesis, if proven to be true, will allow us to control mechanical properties of the composites by tailoring the SiC particles formed. It is also pointed out that the microstructure requires Si to be the dominant diffusing species and to diffuse through the reaction layer, while Nb and Conly have to undergo local rearrangement.

Jan 1, 1996

By Eddie C. Chou

Phelps Dodge, Inc. (PD) is currently developing a lateritic nicke/Vcobalt deposit in Madagascar. Hazen Research, Inc. provides technical assistance to PD to investigate recovery processes for nickel and cobalt. Various process options were evaluated in laboratory experiments and pilot plant operations. The process selected for the feasibility study consists of feed preparation, high-pressure acid leach, countercurrent decantation wash, sulfide precipitation, sulfide dissolution, solvent extraction, ion exchange, and electrowinning. Among these unit processes, high-pressure acid leach, sulfide precipitation, and sulfide dissolution are applications of pressure technologies. Process development work and design criteria for commercial operations of these unit processes are presented in this paper. Concerns related to scaling in the high-pressure acid leach and the sulfide precipitation processes are discussed. Corrosion of various metal coupons under these environments was examined.

Jan 1, 2000