Search Documents

By G. A. Irons, D. Guo, D. Angheiina

To produce low-carbon (<30 ppm) steel in the tank degassing process, a ladle of steel with an oxidizing slag is placed in a vacuum tank equipped with bottom bubbling. The kinetics of this process are slow compared to the more prevalent RH degassing process, providing the impetus for the present work. There are several aspects to this work: water models of the fluid flow in the ladle; simulation of the decarburization (CO evolution) with C02 desorption in water; pilot-plant (60 kg) studies of the decarburization kinetics; mathematical modelling of the fluid flow in the ladle; mathematical models for each of the kinetic sites (plume, top slag and auto-nucleation); and full-scale trials. The results show that during the refining cycle the contribution from each reaction site changes, suggesting avenues for reducing cycling time and final carbon contents.

Jan 1, 2000

By Niels Verbaan, Ralph Fitch, Charlotte Forstner, David Dreisinger

A process has been developed to extract gold, silver, indium, gallium, lead, copper, zinc, and other metals from a large resource using an oxidizing acid chloride heap leaching technology. The ore is crushed and/or ground to improve reactivity and then contacted with a solution containing NaCl-HCl-NaOCl. The value metals are leached into solution as chloro-complexes. The leachate is treated in a series of separation and recovery processes to produce separate saleable or disposable products. The paper will provide a summary of process development and application to a silver-indium ore from Bolivia. The possible application of the process to other ore types will be presented for discussion.

Jan 1, 2015

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Muammer Kaya, Sait Kursunoglu

"The aim of this study was to investigate the effectiveness of ascorbic (C6H8O6) / oxalic (C2H2O4) acid as a reductant for the simultaneous recovery of zinc and manganese from a spent and mixed zinc-carbon and alkaline battery powder in sulphuric acid leaching. The effects of sulfuric acid concentration, ascorbic/oxalic acid dosages, reaction temperature and leaching time on the zinc and manganese dissolutions were investigated according to 2k full factorial experimental design; then, a simple optimization study was carried out for the best reductant. The optimum reductive acid leaching conditions were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M sulfuric acid concentration, 13 g/L ascorbic acid dosage, 1/20 g/mL solid/liquid ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. When our results were compared with the previous results, our findings were better than previous studies.In addition, the manganese dissolution kinetics was undertaken, and the activation energy was found to be 7.04 kJ/mol. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leaching solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover zinc and manganese."

Jan 1, 2012

By Corby G. Anderson

In the majority of industrial operations recovering gold and silver by hydrometallurgical means, cyanide is the predominant lixiviant. However, as an economic alternative, production of massive quantifies of silver chloride was done on an industrial scale in the nitrous-sulfuric acid pressure leaching of a refractory precious metals concentrate. This proven process required no cyanide. Thus, because of the large volumes encountered during day-to-day plant operation, the need for efficient and low cost methods of silver chloride precipitation, reduction and materials handling was mandatory. As such, this paper covers the evolution of plant scale precipitation, filtration, washing, reduction and control of silver chloride processing. As well, an in-depth description of the unique leaching system is included.

Jan 1, 1998

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013

By Brad Wahlquist

An ex-situ biological treatment system was implemented at a gold mine site in South Dakota. The system removes selenium and nitrate from a mixture of groundwater and surface water runoff at ambient water temperatures. The Applied Biosciences? system replaced a denitrification system that did not perform consistently, did not treat for selenium and required heating of the influent water. Installation was completed in phases starting with the selenium circuit being brought into operation in February, 2002 and the nitrate circuit in March, 2002. System design can accommodate average flows of 380 L/min (100 gallons/minute) and a maximum flow of 1,136 L/min (300 gallons/min). Four cells were designed to remove nitrate from approximately 30 mg/L to below 10 mg/L and two cells were designed to remove selenium from 0.01 mg/L and higher, to below 0.005 mg/L. No pretreatment is required to operate the system at ambient temperatures, which can fall as low as -12C in the winter, and treat water at temperatures ranging between 8C to 16C. Nutrient requirements are met using a sugar based nutrient mixture that includes a balanced C:N:P:S ratio, trace elements and vitamins. Since start up, the system has consistently been in compliance for nitrate and selenium, treating water to below detection limits for both contaminants. This paper discusses laboratory biotreatability testing of a system designed to remove selenium, arsenic, and nitrate and full-scale implementation and optimization of a system to remove nitrate and selenium.

Jan 1, 2003

By László I. Kiss, Verena Mackowiak, Alexandre Perron, Dominic Toulouse, Alicia Liedtke, Sándor Poncsák

"Bubbles play a very important role in different metallurgical applications like for example in electrowinning. During heterogeneous nucleation, the maximal size of the bubbles growing at the nucleation sites as well as the nucleation frequency is determined by the so-called detachment condition. Detachment occurs when the external forces acting on the bubble exceed the retaining forces along the solid-gas-liquid triple interface line. The phenomenon depends strongly on the shape and orientation of the solid surface and on the nature and strength of the external buoyancy and drag forces. In the present study the detachment conditions of bubbles from downward facing horizontal and inclined plates were studied experimentally under the effect of gravitational and hydrodynamic forces. The results show the deformation of the bubbles under the effect of the external forces and the detachment conditions as function of the bubble volume.IntroductionIn heterogeneous nucleation bubbles are generated at the so-called nucleation sites along the solid-liquid interfaces. They continue to grow there and after they reached a certain size they detach from the solid surface and leave the nucleation site. This scenario is well known both in boiling and electrolysis. During the growth period a stable equilibrium exists between the forces that retain the bubble at the nucleation site and the forces that try to remove it. This equilibrium evolves with the increasing volume of the bubble to the point when the detachment forces overcome the retaining forces.The life of a single bubble generated by heterogeneous nucleation can be divided into two periods separated by the detachment - or in other words by the departure - of the bubble: first the growth at the nucleation site and then the movement away. The knowledge of the detachment conditions makes possible the determination of the maximal volume of the bubble at the nucleation site that, in tum, makes possible the determination of the nucleation frequency. This is why so many researches have been directed toward the clarification of the details of the bubble detachment in the past decades. The equilibrium between the attaching and separating forces depend on the presence of body, surface and flow induced forces in the liquid, on the geometry and orientation of solid surface, on the properties of the solid-liquidgas system etc."

Jan 1, 2004

By P. Peczak

A Monte Carlo simulation technique has been used to study dynamic recrystallization in polycrystals. A continuum microstructure of the polycrystal is modeled employing a discrete lattice. The response of the material to hot deformation is simulated by adding stored energy and recrystallization nuclei continuously with time. The experimentally observed nonuniform character of deformation substructures is modeled by employing a phenomenological expression for inhomogeneous distribution of the stored energy. All simulations were performed on HP-Apollo 9000 Series 700 workstations. A program written in FORTRAN with use of PHIGS graphics library calls was used to interactively monitor the current state of the matrix and all relevant parameters: deformation stress, average grain size and effective nucleation rate. Visual analysis of the simulated microstructure allows a better understanding of the data developed by averaging over a number of very long Monte Carlo runs. Since the essential features of dynamic recrystallization are accurately reproduced by the model, it is used to discuss the role of the controlling mechanisms of the dynamic recrystallization in real polycrystal.

Jan 1, 1993

By Guanyong Shi, Zhihe Dou, Cong Wang, Ting'an Zhang, Hongyan Zhang

We prepared the CuCr alloy by thermit reduction-electromagnetic casting. But there are the defects such as stomata and oxide inclusions in CuCr alloy. In this paper, the existing state and distribution of inclusions and stomata in CuCr alloy are systematically analyzed. The alloy was characterized via SEM, EDS and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that: there are three distinct areas: copper-rich areas, chromium-rich areas and the inclusion areas. Inclusions are mainly in the form of stomata and Al2O3 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Then, the composition of phases of the smelting slags and alloy were characterized via XRD. The results show that: the slag consists of Al2O3 and a little of Cr, the alloy consists of Cr, Cu and a little of Al2O3.

Jan 1, 2015

By Honglei Zhang, Wuguo Xiang, Xinhao Huang, Guotao Xu, Xilai Chen

"The service behavior of refractories used in hot air pipeline for hot air stoves in a 3200 M3 blast furnace of WISCO was analyzed. The damage factors can be concluded as the poor quality of and alusite based bricks, the severe thermal shock damage, the more porosity in structures, loose bonding capability, and the unreasonable choice of materials and design of bricks. By analysis, the service life of hot air stoves can be enhanced by the measurements such as the reasonable choice of materials and their match, the use of light-weight refractories, the improvement of brick type, etc. Thereafter, the normal production operation of hot air stoves is guaranteed.IntroductionThe No.7 blast furnace of WISCO has been used for about 5 years and it was mid-repaired in March, 2012. The top phenomena of worn hot air pipelines are brick drop, breakage, severely local wear and deformation, existing hidden danger, so the worn hot air pipelines were renewed. Investigations have been done on the stove damage and design [1,2]. In order to clarify the wear mechanism, the used refractories for hot air pipelines were sampled and analyzed, the properties and structures of worn materials and reused materials are relatively studied."

Jan 1, 2013

By H. Eccles

BNFL, an internationally acclaimed company noted for its nuclear fuel cycle services and waste management technologies, collaborated with Viridian BioProcessing Ltd, a small company acknowledged for developing environmental biological processes, and an internationally recognised professor of biological sciences, to develop an unique bioremediation process for treating toxic, heavy metal contaminated land. This paper describes the process, with particular reference to the problem and scope of land contamination with toxic, heavy metals and the current available technologies. The process technologies are based on using indigenous, soil micro-organisms which can be stimulated to produce acid or sulphide ions to mobilise or precipitate the heavy metals respectively. Laboratory studies have indicated metal removal efficiencies of greater than 90 % can be achieved, whilst recovery efficiencies from the metal loaded leachate are even higher at approximately 95%.

Jan 1, 1996

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009