Search Documents

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace 'bindings, to enhance the furnace's structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By Shilai Yuan, Huimin Lu, Liyuan Zhao, Zhijiang Gao

"A purification process was developed to removal impurity element boron from metallurgical grade silicon by electromagnetic induction slag melting. Vacuum melting furnace was used to purify boron in both Al2O3-MgO-CaO-SiO2 slag system and Al2O3-CaO-SiO2 slag system. The relationship between different slag chemistry and the removal of boron in silicon were studied using Back Propagation (BP) Neural Network model. The best slag chemistry for the removal of boron was predicted by Genetic Algorithm (GA) contributed by the use of Matlab. The results show that the mass fraction of Boron in silicon is reduced from 11.7496×10-6 to 2.3259×10-6 after slag melting in 28.96%Al2O3-3.43%MgO-36.24%CaO-31.37%SiO2 slag system. The relative error obtained with GA-BP Neural Network model was below 0.35%.IntroductionSolar energy, due to its low green house gas emissions, has been paid great attention. Accordingly, the demand for solar grade silicon (SoG-Si) has been growing rapidly. The quest for developing a low-cost method of producing SoG-Si has been moving forward in the last decade. Refining of metallurgical-grade silicon (MG-Si) attracts research interest due to its low material and energy costs, and more environmentally friendly technology in comparison to the traditional Simens process. As such, impurity elements in MG-Si must be removed to low levels for the photovoltaics (PV) cell to operate at optimum efficiency. Most impurities in metallurgical-grade silicon (MG-Si), especially metal elements, can be separated by directional solidification and the zone refining plasma-arc method [1, 2]. The main focus in refining MG-Si to SoG-Si is on the impurities which are the most difficult to remove. Boron has relatively high segregation coefficients (KB=0.8, concentration of Boron in solid silicon divided by its concentration in liquid silicon) [3] and higher vapor tension (the saturated vapor pressure of boron and silicon are 6.78×10-7 Pa and 0.4 Pa, respectively). The vacuum melting and directional solidification methods hence have no effects on boron removal.Slag refining involves melting MG-Si in the presence of a flux to produce a slag phase that can take up the impurity elements. The mechanism of slag refining is considered to include two main steps: the oxidation of boron and the absorption of boron oxide by slag materials. The oxidation of boron, described by the oxygen potential (PO2), resulting from the equilibrium Si and SiO2. The absorption of boron oxide, described as the slag basicity, is interpreted as expected to facilitate their extraction to alkali and alkali-earth oxides in the slag phase. Thus, effective removal may be obtained for a certain slag composition. Researchers [4-5] examined the effect of boron removal in CaO-SiO2 based ternary systems and showed that the addition of excess CaO can decrease the activity of SiO2. Researchers [6-8] studied the boron behaviors in CaO-SiO2-Al2O3, CaO-SiO2-Na2O, Al2O3-BaO-SiO2, CaO-SiO2-Li2O and Al2O3-CaO-MgO-SiO2 slag systems by adding boron in the silicon to a degree. Li2O, Na2O, MgO and BaO are thought to be associated with B2O3."

Jan 1, 2014

By James P. Bennett

The U.S. Bureau of Mines, Tuscaloosa Research Center, is conducting a review of the usage of different types of refractories, the current industrial practices to recycle/dispose of spent refractories, and the concerns associated with these practices. This information will serve as the technical basis for initiating a research program to recycle or find alternate uses for spent refractory materials. Approximately 1.6 million metric tons of clay based and 1.2 million metric tons of non-clay based refractory materials were manufactured in the United States in 1992 alone, representing a value of almost 2 billion dollars. Landfill has been and remains the disposal means of choice. Issues such as environmental regulations, concerns over landfill disposal, future liability, and product stewardship programs have brought about increased emphasis for recycling or alternate material use. Information on refractory consumption and the issues associated with recycling or disposing of used materials will be discussed, including current recycling practices.

Jan 1, 1995

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu20), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, CU2O- bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties ofthe CaO-FeOx-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation.

Jan 1, 2003

By John W. Graydon

Incineration is an attractive alternative to the disposal of MSW in landfill sites. However, the process of incineration generates fly ash which contains significant levels of leachable heavy metals - particularly cadmium, lead, and zinc - and it is essential to manage this fly ash in an environmentally sound manner. The compositions, phases, textures, morphologies and size of fly ash particles have been studied by light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how fly ash is formed during incineration, in understanding the leaching behavior of untreated fly ash if it is disposed of in a landfill and, most importantly, in guiding the development of the best treatment strategies for fly asti to mitigate its environmental impact.

Jan 1, 1992

By H. C. Roland Kammel

Stannous sulfate electrolytes are widely used nowadays in electrolytic tin production. Characteristic features of this electrolysis process are that dense cathode deposits can only be obtained by additions of organic additives and that so called ?black mud is formed on the anode surface which leads to an increase in cell-voltage. In order to prevent excessive cell-voltages or oxygen evolution the black mud has to be removed periodically. Studies in laboratory scale have been performed about the effect of different organic additives on electrolytic tin deposition and the formation of surface layers on pure and industrial tin anodes. Results reveal that organic addition agents are effective in reducing cathode roughening as well as extending the covering time of the anode ?by black muds.

Jan 1, 1985

By Pengfu Tan

A thermo-chemical model of the copper P-S converter and a viscosity model for the converter slag have been developed to predict the behavior of magnetite in the converter slag, amounts of slag and matte, compositions of slag and matte, volume of the bath, bath temperature, slag blow endpoint determination, SEMTECH OPC signals, and the viscosity of converter slags. The predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by the industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on Fe3O4 content in converter slag, slag viscosity, liquidus temperature of converter slag and skimming operation has been modeled and discussed as well. Some applications of the industrial operations have been presented.

Jan 1, 2009

By Walter Curlook

An atmospheric acid leaching process for leaching nickel and cobalt from highly-serpentinized saprolitic fractions of nickel laterite deposits has been developed and patented [I]. The process involves leaching the highly-serpentinized saprolitic portion of the nickel laterite ore profile in strong sulphuric acid solutions at atmospheric pressure and temperatures between 80°C and 100°C, essentially autogenously, to extract over 85% of its contained nickel content and a large proportion of its cobalt content after leaching times of about one hour. The amount of sulphuric acid used in the leaching process is between 80% and 100% by weight of the finely ground highly-serpentinized saprolite ore on a dry weight basis. The metal values are recovered as intermediate products. Key words: Atmospheric Leaching; Nickel Oxide Ores; Laterites

Jan 1, 2004

By Jie Li, Liangxing Jiang, Yexiang Liu, Junfeng Gui, Bo Hong, Xiaocong Zhong, Yanqing Lai, Xiaoying Yu

"Pb-based alloys with Pr and Ag were prepared in vacuum electromagnetic induction furnace. The tensile strength, corrosion rate and anodic potential in sulfate solution were measured, and the experimental data were analyzed according to the metallographic phases of alloys, the micromorphology and composition of their oxide films. The results show that, with the addition of Pr, the ultimate tensile strength and corrosion rate of pure lead were increased, and the anodic potential decreased. The extra addition of Ag can improve the properties of alloy further. Comparing with Pb-Ag0.8 alloy which is widely used in zinc electrowinning industry, the ultimate tensile strength of Pb-Ag0.6-Pr2.0 alloy was increased by 31.75%, the anodic potential under 50mA/cm2 was decreased by 30m V.IntroductionIn zinc electrowinning industry, the Pb-Ag (0.5-1.0 wt.%, 0.8wt.% normally) anode is widely used as an insoluble anode['l. It can meet the basic requirements, but still has several problems such as high oxygen evolution over-potential (about 860mV), unsatisfactory corrosion resistance, lead contamination of the cathode product and high consumption of Ag etc.In order to reduce the energy consumption, enhance the corrosion resistance, improve the product quality and reduce the consumption of Ag (or even dispense with it), much research has been done, mainly focusing on Pb-based alloy anodes and Ti-based coated anodes. Detailed investigations have already been carried out on binary alloys (Pb-Ca and Pb-Co), ternary alloys (Pb-Ag-Ca, Pb-Ag-Ti, Pb-Ag-Sn, Pb-Sr-Sn, and Pb-Ca-Sn) and quaternary alloys (Pb-Ca-Sr-Ag, Pb-Ca-Ce-Ag, and Pb-Ag-Sn-Co)[Z-4l, Although these anodes can effectively reduce the consumption of Ag, only the Pb-Co and Pb-Ag-Sn-Co anodes perform well with regard to reducing the anodic potential. However, their complicated manufacturing conditions restrict further commercial use.Besides its application in nonferrous metal electro-winning industry, Pb-based alloy is also used as grid alloy for lead-acid battery, serving as active materials supporter and current collector. In order to enhance the corrosion resistance and deep-cycling performance, reduce the impedance of the corrosion film, the addition of appropriate rare earth elements into anodic grid alloys has become a research focus. Studies proved that RE can enhance the mechanical strength of grids, inhibit the formation of anodic Pb(II) film on the surface of grids and then reduce the impedance of the film[ 10-12l."

Jan 1, 2013

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By Zhao-feng Xie

A new process of recycling valuable metals containing in the slag of jamesonite smelting in the blast furnace was studied. In this process, the valuable metals such as Pb, Sb, Zn and In etc. were fumed and volatilized and enriched in the dust firstly and then the dust was leached by sulfuric acid. In the leaching procedure, Zn and In in the dust entered into the leaching solution and were separated from Pb and Sb which remained in the residue.The optimal operation conditions of the fuming procedure are as follows: the mass ratio of the blast furnace slag, coal powder and lime are 100:22:10 respectively and the fuming time are 1.5~2.5 h, the fuming temperature is not below 1200C and the volatilization rates of Pb, Sb, Zn and In are 95%, 92%, 86% and 75% respectively. The optimal conditions for the leaching procedure are also presented: the consumption of sulfuric acid is 1.15 times of the theoretical consumption, the ratio of liquid to solid is 4:1 and the leaching temperature, leaching -1time and stirring speed are 90, 1.5h and 300 r?min separately. The leaching rates of Zn and In are 98.5% and 95.2% respectively. The experimental results shows that the valuable metals in the dust can be recovered and separated effectively by this process and the?ir recovery efficiencies are as follows: Pb94%,Sb91%, Zn84% and In69%.

Jan 1, 2009

By D. W. Lawler

Prior to the manufacture of sulphuric acid in metallurgical plants, the SO2 rich gas from the smelter, roaster, or furnace must be cleaned to removed particulates, volatile contaminants, SO3, and water. Cleaning is accomplished by contacting the. gas with cooled weak acid. The system is designed so that all the contaminants, originally in the gas are captured in the weak acid, which then becomes an effluent from the plant. Historically, the entire weak acid effluent stream has been treated for disposal, with no attempt to recycle or recover any part if it. This is becoming increasingly environmentally unacceptable, and operators must consider better methods of treatment and recovery. In this paper, Kvaerner Chemetics discuss a number of options that allow the contaminants to 'be separated from the acid' value. This will result in an acid byproduct that can be sold or used elsewhere, and will minimize the volume of hazardous byproducts that must be discharged.

Jan 1, 1998

By Xie Zhang, Chongyang Zhao, Qingyun Huang, Bing Xie, Xiaopeng Zhen

"Extracting vanadium from vanadium containing hot metal into vanadium slag by BOF is the main vanadium production process in China. In this paper, the influence of Si content in hot metal on the quality of vanadium slag is analyzed. Synthetic vanadium slag with different SiO2 content were melted at 1673 K and then cooled to 303K at the cooling rate of 3?/min. Optical microscopy, SEM, EDS and XRD were used to analyze the mineralogical phases and crystallization behavior of vanadium slag. The results show that vanadium slag mainly contains spinel phase and silicate phase; V is enriched in the spinel phases while Si is concentrated in Fe2SiO4 CaFeSi2O6 and (Fe,Mn)2SiO4 as silicate phase. The melting point of slag increases gradually with the addition of SiO2; whereas viscosity decreases with an addition of 15~19% SiO2 and increases with an addition of 19~27% SiO2.IntroductionVanadium is an important element which is used almost exclusively in ferrous and non-ferrous alloys. The major vanadium products include FeV, V2O5, V2O3, VN and Al-V-Ti alloy. Furthermore, vanadium slags are mostly produced by oxidizing the elements in V-containing hot metal during a duplex refining process. Therefore, the process of removing vanadium from hot metal has its significance on the subsequent process[1].The extraction of vanadium is greatly affected by the mineralogical composition of vanadium slag[2], the distribution of the elements between the spinel and silicate phases and its physic-chemical properties. These characteristics of vanadium slag have been studied in some details. It has been reported that Si mainly exists mainly in the form of silicate which wraps the spinel crystals while small amount of Si stands as phosphorus quartz or diopside[2]. Chen et al.[3, 4] points out, when SiO2 content in vanadium slag increased every 1%, V2O5 decreased 1.48%. Moreover, silicate phases would embarrass the oxidation of V-containing spinels through decreasing the exposing probability[5]. Meanwhile, melting point and viscosity of vanadium slag has been greatly influenced by the SiO2 content. Therefore, this work attempts to analyze the above-mentioned questions systematically."

Jan 1, 2012

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015

By J. Phillip Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By Zbigniew Zurecki

The selection of atmosphere composition is critical for controlling surface quality of reactive aluminum alloys during solution treatments. An improper selection of annealing atmosphere can result in surface blistering in AI-Mg and sub-surface depletion of lithium in AI-U ingots. To determine optimum atmosphere compositions for homogenizing A1-Mg and Al-Li alloys, Ii number of exploratory experiments were carried out in air, nitrogen, and carbon dioxide based atmospheres including reactive impurities or additive such as moisture and sulfur hexafluoride. This paper describes the influence of these atmospheres on high-temperature oxidation and sub-surface defects. The results are discussed in terms of the change in Pilling-Bedworth ratio.

Jan 1, 1996

By D. M. Dabbs

A static dew point technique has been used to evaluate the solubility of arsenic in ?slag and its dependency on P02 at temperatures of 1458 and 1523K. The ferrous-ferric ion ratio of the slags ranged from 3.9 to 23.8. These values correspond to partial pressures of 02 ranging from 10-8 to 10-12 atm. The solubility of arsenic in slag was found to be independent of? P02? The data indicate that elemental arsenic exists in silicate ?slags. This result was further substantiated by mass .spectrometric analysis of doped slag specimens.

Jan 1, 1983

By M. Okido, O. Takai, Z. Zhao, M. Ishikawa, R. Ichino, K. Kuroda

"Electrolytic method was applied to calcium phosphate coating on titanium plates as an excellent technique for high density and intensive contact of coated films on biomaterials. The effect of H2O 2 as oxidation reagent on coating characteristics was examined to obtain biomineral films. Solution was containing 7.0 X 10·3 mol/dm3 ofCaC12 and 3.0 X 10·2 of Ca(H2PO4)z, kept at 55 ""C. All deposits were hydroxyapatite (HAp) in this study, independent of H2O 2 concentration, applied cathodic potential and solution pH. In the case of H2O 2 addition, an increase in cathode current started at the low potential, namely, ca. -0.2 V (vs. SCE). In contrast, the current increased at more than ca. -1.4 V in the solution without H2O 2 addition. H2O 2 appeared to be an effective reagent for increasing nucleation density and improving adhesion of deposits on titanium plates.IntroductionIn recent years, many researches have been undertaken to develop the techniques of calcium phosphate coating on titanium or bioglass for medical implantation. High density and intensive adhesion of coating are necessary for adding bioaffinity to these materials and for inducing bone morphogenesis on them when implanted in human body.1) Electrolytic deposition has been a newly developed method as high-speed deposition process. By this method, the supersaturation of calcium phosphate can be increased just in the vicinity of metal substrates and the heterogeneous nucleation is promoted on them. In this process, H2O is reduced according to eq. (1) on the cathodically polarized electrode"

Jan 1, 2000

By H. Deveci

Bioleaching/biooxidation is essentially a dissolution process with the involvement of acidophilic bacteria acting as the "catalyst" to accelerate the dissolution of metals from sulfide minerals. The contribution of bacteria to the metal dissolution is closely controlled by the growth of bacteria, which is itself affected by the physico-chemical conditions within the bioleaching environment. There are a number of operating parameters controlling bioleaching processes, which are required to be maintained within a certain range in the leaching environment whereby the activity of bacteria with the resultant oxidation of sulfide minerals can be optimized. In this regard temperature, acidity, oxidizing conditions, availability of nutrients, oxygen and carbon dioxide, surface area and presence of toxic ions are of prime importance for control and optimization of bioleaching of sulfide ores/concentrates. Bioleaching processes are temperature and pH dependent with optimum metal dissolution occurring in a particular range where the bacterial strain is most active e.g. mesophiles at 35-40°C and pH 1.6-2.0. Provision of nutrient salts is required to maintain the optimnm growth and hence metal dissolution with the quantity of nutrients apparently being dependent on the availability of substrate i.e. head grade/pulp density of an ore/concentrate. Oxygen transfer is one of the most critical factors since the oxygen levels below 1-2 mgll may adversely affect the oxidizing activity of bacteria. Bioleaching rate tends to improve with increasing the surface area at low pulp densities but, in practice. the pulp density is limited to -20010 w/v. Increasing concentrations of ions such as cr may also adversely affect the oxidative activity of bacteria. Keywords: Bioleaching, Biooxidation, Acidophilic bacteria

Jan 1, 2003

By Paula Ana Paiva

The high economic value and unique technological properties of the platinum-group metals (PGMs), plus their growing scarcity in the Earth’s crust, justify the crucial importance of developing recycling practices for PGMs end-of-life materials. Examples of top devices relying on the use of PGMs are automotive and industrial catalysts, and electrical and electronics equipment. This article critically describes the most recent research on the use of solvent extraction to recover one PGM, palladium, from spent catalysts. Some groups focus on the development of schemes involving commercial extractants, while others prefer to design specific molecules to efficiently and selectively recover palladium from these particular complex leaching solutions. Examples of commercial extractants proposed for the former schemes are Alamine® 308, TBP and LIX® 84I; while on the other hand, sulfur-containing diamides, thioamides, thiocarbamates, and dithioethers have recently been developed. Ionic liquids have to be mentioned too.