Search Documents

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By D. L. Jones

The leaching of natural chalcopyrite was studied in both ferric sulfate and ferric chloride solutions. The chemistry of the two reactions is quite different, with substantial sulfur oxidation occurring only in sulfate solutions. Ferric chloride is a more effective reagent, for the leaching rate is greatly increased with finer particles and higher (Fe+++), and unaffected by high (Fe++); none of these advantages are found with ferric sulfate. In addition, the morphology of leaching appears to be different, with ferric sulfate leaching preferentially along fissures or grain boundaries. The kinetics were found to be linear over an extended period, rather than parabolic as reported elsewhere. An explanation of the observed phenanena is proposed using the electrochemical theory of leaching, and experimental measurement of the mixed potential of the mineral during leaching.

Jan 1, 1976

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By Emanuel Negrao Macedo, Edinaldo Cunha, Mauro Oliveira, Jose Antonio da Silva Souza

"This paper presents the study of the increasing addition influence of the bauxite waste in some properties of polymeric matrices composites reinforced with natural fiber: Curaua (Ananas Erectifolius smith). There were evaluated properties as density, tensile and flexural resistances. The high pH provided by the waste is used as hydrolysis agent, providing the pectin cement dissolution of the fiber bundles, and therefore, improving the mechanical adhesion in the fibermatrix interface and the increase of the fiber bundles aspect ratio. Furthermore, the content of silico-aluminous material in the waste provides increase in the composite abrasivity, which is destined to civil and naval construction. The fact of being a low-cost and highly available waste turns the red mud in a high potential material as polymeric composite filler.IntroductionRed mud is an insoluble residue, originated from the bauxite refining through the Bayer Process [1]. It is an Iron Oxide rich material [2] (substance responsible for the red brick color), it has a complex chemical composition [3], and its composition is highly dependent of the type of bauxite used in the process [4]. It has high alkalinity (pH= 10 - 12.5) and a very small solids size distribution (95% diameter< 44µm) [1], what turns the red mud a serious environmental pollutant.The utilization of fillers on composite materials is done after many necessities; however, one of the major necessities is the cost reduction [5]. Furthermore, mechanical and thermal properties of polymers usually are improved by the addition of inorganic fillers [6], being an example of this improvement the reduction of the flammability of polymer matrixes due to the addition of functional clays [7]. In this way, the red mud becomes potential filler for composites, since cheap and easily available fillers (like red mud) are a good option to reduce costs [8]."

Jan 1, 2013

By Alexander I. Raitchenko

"Although one takes into account only thermal expansion usually at analysis of convection onset, the essential factors include magnetic and electric fields. If Lorentz-force originating from intercrossed electric and magnetic fields' action is directed downwards its effect strengthens gravitational action, and value of critical Rayleigh number (limit value for convection onset) must decrease; increasing of critical Rayleigh number should be observed in case of Lorentz-force directed upwards. Extent of such an influence is determined by relation of Lorentz-force to hydrostatic head in gravitational field. Competition between electromagnetic force due to nonuniformity of electroconductivity (on account of its temperature dependence) and electromagnetic buoyancy force may have ambiguous effect: both increase or decrease of critical Rayleigh numbers. Proposed conception is applicable to analysis of situations in liquid conductors and conductive gases.IntroductionStatic or dynamic situations in fluid media are determined besides properties of these media by a variety of external influences. However one correlate~ the onset of the convection and its development with influences of the minimum quantity of external causes frequently. Most known and usual factors are the gravitational and temperature fields. The number of processes includes heat generation in media volume, and theoretical analysis in these cases takes into account this interior heating together with boundary temperature conditions. But explanation of many natural and technical events is not complete and cogent within limits of thermo-gravitational terms. The whole complex of acting factors which influence convective processes in techniques and nature is greater in many cases. In particular the action of · electromagnetic nature often has not less importance than gravitation one. Stability or instability of a current layer in the plasma must be determined by non-uniformity of electroconductivity owing to non-uniformity of temperature [1]. The presence of Joule dissipation in the plasma through which the electric current flows stipulates initiation of origin of overheated instability [2]. It is known that electroconductivity of arc in the boundary zone changes sharply with radial distance [3], and this must influence its stability essentially. If the intercrossed electric current and magnetic field begin to act on an electroconductive fluid besides the non-uniform temperature field and the gravity, the conditions for the onset of the convection change radi- . cally: both the temperature field and their solutions have to be changed also. The analysis of equilibrium single-time correlation functions of fluctuations must be employed for situations with enlarged number of factors as this was in case for the Rayleigh-Benard problem where the object is a horizontal layer of liquid. This can be carried out by taking into account the detached forces' correlations [ 4, 5]"

Jan 1, 1999

By Herbert H. Kellogg

A model of the ISF is described. which reproduces with accuracy the "normal" operation of three industrial furnaces. The model, written in Fortran, is based on detailed heat and material balances, and the concept that the ascending gases reach equilibrium with zinc oxide and with the water-gas shift reaction. "Solution loss" of carbon in the lower shaft, and partial reoxidation of zinc vapor in the upper shaft are also essential features. For prediction of furnace behavior under altered operating conditions (blast rate, temperature, moisture content, oxygen enrichment, or injection of oil or coal through the tuyeres) the model modifies the heat loss, temperature of slag and bullion, amount of reoxidation in the upper shaft and the condenser efficiency to reflect the altered operating parameters. Model predictions for such operating conditions are in reasonable agreement with plant experience.

Jan 1, 1990

By D. Lui, B. G. Thomas, B. Ho

"Results from mathematical models and plant experiments are combined to quantify the effect of transverse depressions and oscillation marks on heat transfer in the continuous casting mold. A heat transfer model has been developed to calculate transient heat conduction within the solidifying steel, coupled with the steady-state heat conduction with the continuous casting mold wall. The model features a detailed treatment of the interfacial gap between the shell and mold, including mass and momentum balances on the solid and liquid powder layers. The model predicts the solidified shell thickness down the mold, temperature in the mold and shell, thickness of the resolidified and liquid powder layers, heat flux distribution down the mold, mold water temperature rise, ideal taper of the mold walls, and other related phenomena. The important effect of non-uniform distribution of superheat is incorporated using the results from previous 3-D turbulent fluid flow calculations within the liquid cavity. Results from plant experiments confirm that transverse surface depressions and oscillation marks form at the meniscus and move down the mold. Measurements of mold thermocouple temperatures and breakout shell thickness were used to calibrate the models. The results indicate that the surface depressions and oscillation marks are filled with mold flux, but still have a significant effect on decreasing heat transfer. The predicted mold temperature fluctuations are consistent with measurements. If the depressions become filled with air, their effect is greatly increased. These results should be useful in the difficult task of interpreting transient mold thermocouple signals for on-line quality monitoring.IntroductionMany different types of intermittent surface defects on steel slabs arise during initial solidification in the mold of the. continuous casting machine. These defects include deep oscillation marks, surface depressions, and cracks. They may lead to quality problems, such as slivers, in the final rolled product. In severe cases, breakouts may occur, where liquid steel bursts through a thin section of the shell and drains over the casting machine below the mold."

Jan 1, 1997

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By Olexandr Gydin

The evolution of grain and dislocation structures during cold deformation of the new steel LH800 of Salzgitter AG is investigated in the frame of this work. The main feature of this material is its ability to air-harden by carbon content of about 0.1%. The initial ferrite structure of the metal provides high plasticity at cold deformation and subsequent heat treatment increases tensile strength approximately two times. Described are results of in-situ tensile tests in the SEM. SEM and TEM analysis of grain and dislocation structures evolution in samples, which have been uniaxially deformed to certain strains, are carried out. After statistical evaluation of results the grain elongation against strain is determined. A microstructure of a deep drawn cup is analyzed by means of SEM. A quantitative evaluation of grain elongation on the different cup zones and comparison of these data with prediction results based on tensile tests are carried out.

Jan 1, 2009

By S. A. Davis

In July of 1996, the Kroll process began production again at TIMET&apos;s Henderson, NV, manufacturing facility. This, after being shut down for several years due to low market demand for titanium. Faced with limited pond capacity and increasing costs for water and wastewater disposal and storage; process changes were made to recycle water used to wash Kroll titanium sponge back into the sponge leaching process. This idea was revisited from 1992-93, when three consecutive attempts to recycle water for this application were unsuccessful due to early pump failure. Since it was uncertain why previous attempts failed, a complete understanding of the existing system was first sought. This included reviewing piping and flow diagrams; taking field measurements for all the piping, valves, and fittings; analyzing the wastewater composition; and modeling the fluid dynamics and control of the system. The fluid dynamics of the system were modeled by breaking the piping network up into nodes and applying the Bernoulli equation to each segment. The fluid flowrate control valves were modeled for this purpose also and the models were used to help specify the required processing equipment and control ranges and tolerances. Once the project was completed, an operating procedure was prepared for operation, startup, and shutdown of the washer water recycle system.

Jan 1, 1999

By S. P. Mathew

The ISASMELT Lead Process is a continuous two stage process for the production of crude lead from concentrate. It is based on the use of a top entry submerged Sirosmelt lance to produce turbulent baths in which high intensity smelting or reduction reactions can occur. The process involves oxidizing the concentrates in the first stage to produce a high lead slag. This slag is tapped continuously and transferred down a launder to a second furnace where it is reduced with coal. Crude lead and discard slag are tapped continuously from this furnace through a single taphole and separated in a conventional forehearth. Process and engineering design work for a commercial scale Lead ISASKELT plant designed to produce 60000 tpa crude lead has been completed. This plant is planned to be operational in 1991.

Jan 1, 1990

By Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"The LCDs are used in televisions, calculators, mobile phones, computers (laptops and tablets), video games and other electronic devices. The advancements in technology make obsolete these devices, causing excessive disposal of LCDs and therefore decreasing life span of landfills. In this context, the LCDs from LED LCD TVs arise as an additional source of waste electrical and electronic equipment (WEEE). Thus, it is essential to develop LCDs recycling methods, beginning with the LCD characterization followed by displays processing, aiming the materials separation and using some Ore Treatment Techniques, and finally, the recovery of indium using acid leaching. The analysis methods that will be used in this work are: Fourier Transform Infrared (FT-IR) and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES).IntroductionLiquid Crystal Display (LCD) technology is applied in modem televisions, calculators, mobile phones, computers and a wide range of electronic devices. It has replaced Cathode Ray Tube (CRT) technology as the most advantageous display product, due to lower electrical power consumption, size and weight reduction, and no radiation emission [ 1]. The constant improving of LCD screen technology reflects on its growing contribution to the amount of waste electrical and electronic equipment (WEEE): an estimated 50 million tons of WEEE are produced every year [2]. Once the most common method of its disposal are landfills, the LCD technology therefore became an environment issue [3].LCD structure is composed by components made by different materials. In order to develop a LCD recycling methodology that gives the right destination to these materials, a previous characterization stage is required. This characterization includes a disassembly process and material identification analysis. One of the LCD components is the screen, which is composed by polymeric and glass layers. The liquid crystal glass was the starting material of this study. It contains indium in the form of indium tin oxide (ITO) film. This ITO film is deposited in the glass by a sputtering process and acts as the electrode material [4,5]. It has in its composition 90% ofln203 and 10% ofSn02 [6]."

Jan 1, 2014

By V. I. Lakshmanan, R. Roy

Base metals and PGMs are currently recovered from sulfide concentrates using pyrometallurgical processes. These processes suffer from several limitations such as being capital intensive, scaling problems, S02 emissions and long delay in value recognition. Alternative hydrometallurgical technologies have so far not been successful and currently total pressure oxidation and partial pressure oxidation hydrometallurgical technologies are being evaluated. Process Research ORTECH has developed a unique hydrometallurgical process to recover base metals and precious metals using mixed chloride technology. In a first stage leach, base metals are recovered and elemental sulfur is liberated from hydrogen sulfide formed during this leaching stage. During second stage leach, precious metals are recovered using proven separation technologies. Some of the advantages of the process are the recovery of elemental sulfur from sulfide sulfur, recycle of the chloride lixiviant thereby eliminating effluent treatment steps and use of excess energy from the Claus reactor for the pyrohydrolysis step.

Jan 1, 2011

By Keith E. Forrester

This paper presents results of laboratory and field optimization of a proprietary processes developed by FESI for the stabilization of heavy metal bearing wastes. The specific waste studies presented within the paper include foundry ash, aluminum sweat furnace ash and a heavy metal contaminated soil. The FESI process chemistry and engineered processes were found to be the most cost efficient demonstrated and available method of stabilizing heavy metals and highly successful in passing regulatory limits.

Jan 1, 1994

By J. J. Kim

In a study of buildup in a green-feed reverberatory furnace, it was determined that approximately half of the crucible area has a moderate buildup of 25 in. or less, and that the area extending 45 f t from the burner end of the furnace has only a slight buildup. The false bottom, averaging 6 in. in thickness, was found to cover the entire crucible area. The stratification of Cr2O3, A12O3, and SiO2 occurs throughout the slag layer; this phenomenon is the principal reason for the formation of the false bottom in the green-feed reverberatory furnace. The false bottom is caused primarily by the settling of FeO*(A1,Cr),03 aggregates, which are derived mainly from returned converter slag. The false bottom can be transformed to a solid permanent buildup in the furnace, particularly when the matte is completely withdrawn. From the material balance of Al2O3 and Cr2O3 around the furnace, It is estimated that the average rate of aluminum chromite accumulation is approximately 0.3 ton per day or less.

Jan 1, 1976

By Junmo Ahn

This study investigated leaching kinetics by alternative lixiviants for copper leaching from chalcopyrite (CuFeS2), the most abundant copper resource in the world. As a refractory sulfide mineral, chalcopyrite shows low copper extraction due to passivation on chalcopyrite surface. Also, decrease of copper grade with high portion chalcopyrite requires the alternative leaching procedure to increase copper recovery. Therefore, alternative lixiviants such as sulfurous acid and methanesulfonic acid (MSA) were tested for both concentrate and low grade ore to enhance copper extraction. Also, an oxidant, hydrogen peroxide, was compared to ferric to find out the improvement of leaching kinetic. In concentrate leaching tests, 30 g/L MSA showed the highest copper extraction (47%), compared to other lixiviants at 75 °C. Periodical H2O2 addition enhanced copper extraction, and above 90% of copper extraction was observed within 96 h by periodical addition of 0.6% H2O2 at 75 °C. The activation energy of chalcopyrite leaching by MSA and H2O2 achieved 40 kJ/mol, which is chemical reaction control. The results of low grade ore leaching tests indicates that no significant difference among lixiviants (H2SO4, H2SO3 and MSA) with ferric was observed, all of which achieved around 37% within 24 h at room temperature. However, significant increase of copper extraction (>80%) was observed at both 20 g/L MSA and 10 g/L H2SO4 conditions by the addition of 10% H2O2.

By G. Cifuentes

The kinetics of the electrolytic oxidation of cyanide to cyanate on PbO2-coated stainless steel anodes have been studied by both experimental and theoretical means. The anodes were based on 316 steel and performed in a satisfactory fashion. The pH of the studied KCN solutions exhibited a constant value about 11. Values for all the kinetic parameters have been determined and a mechanism for the studied reaction is proposed.

Jan 1, 1999

By Vojteh Leskov?ek

The tribological load is the load on forging tools resulting from the relative motions between the plastically deformed workpiece and the die. In comparison to many other forming processes hot die forging has an especially disadvantageous tribological system. The advantages of the application of hard coatings, which are well known for cutting tools, are to a much lesser extent explored for casting, extrusion, molding and forging tools. Increasing the lifetime of these tools is an important task in surface engineering because of the complex loading conditions and often complicated tool geometry. The plasma-assisted chemical-vapor-deposition (PACVD) technique is well suited to depositing hard coatings onto large dies and molds. The aim of this study is to present and discus results obtained on a duplex PACVD hard coating in an industrial application like the hot forging of automotive parts. A new generation of vacuum-melted and remelted (VMR) hot-work tool steels has been developed; these can reach a hardness of 58 HRc, and have a fracture toughness at this hardness equivalent to that of standard hot-work tool steels at 45 HRc. This offers one of two advantages: the steels can be used at the higher hardness to provide resistance to wear or deformation, or, when used at a hardness of 47?49 HRc for hot forging, to provide temper resistance, nitriding behavior and adhesive wear resistance. The results presented here are from a preliminary investigation. The experimental results indicate that the introduction of a proper duplex PACVD hard coating will lead to an improved wear resistance and a longer lifetime for the hot-forging dies. Furthermore, by using a hard, low-friction coating excellent anti-sticking properties can be obtained. At this stage of the investigation it is also necessary to carry out pilot trials to determine the wear resistance and the tool life in practice.

Jan 1, 2006

By James A. Voigt

The efficient separation of metal species from aqueous streams by precipitation techniques requires &apos;a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system-specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems: The effects of solution chemistry, precipitator design, and solvent choice are considered.

Jan 1, 1996

By Thomas P. Battle

Ilmenite (iron titanate) is the source of over 90% of all the titanium produced in the world today. At some point during production of titanium dioxide or titanium metal the iron impurity must be removed. Too often it becomes a waste instead of a product. DuPont and MINPRO have developed a solid-state process which separates the iron and titanium components of ilmenite into different high-purity powders, which can be separated using conventional mineral processing techniques. The main reactor in this process is a unique high-temperature ball mill, where the iron segregates from the ilmenite lattice with the assistance of catalytic quantities of He\. The results of lab, pilot plant, theoretical, and scale-up studies are presented and discussed.

Jan 1, 1996