Search Documents

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By Juan P. Camus, Sergio G. Jarpa

INTRODUCTION Chuquicamata mine is a large copper open pit located in the north of Chile. It has been in production for more than 80 years and now is in the later stages of its life with declining grades and increasing haul distances. As any old mine with long established organizations and procedures, it has faced one of the most difficult managerial problems: to conduct changes. Since 1994, the new management team has been devoted to a modernization pro- gram focused mainly in restructuring business operations. downsizing the labor force and introducing a mine planning pro- cess consistent with the company's goal. The explicit identification of the latter issue has been made because of the management’s conviction about the importance of it in the profitability of the business. The mine planning process at Chuquicamata mine has evolved from an old manual technique towards a modern computarized system, however the fundamental aspects and the procedures involved in this process have been the same. For in- stance, the cutoff grades policy has not changed during the last said 20 years, regardless of the changes to grade distribution, commodity prices, plant capacities, etc. To review and rethink this process, the strategy was to work with a small group of inside engineers and the management in order to interact with several mining consulting firms. The idea was to open a discussion about the fundamental principles used in the mine planning activities and, at the same time, to explore new ideas to improve the operating practices that have been followed for a long time. Thus, the goal of this paper is to present the mine planning approach that was the result of this work and the improvements that were obtained. THE CHUQUICAMATA MINE The Chuquicamata division is one of the five operations of Codelco and is currently devoted to operating the Chuquicamata mine; a copper open pit, concentrator, smelting and refining complex. It also operates Mina Sur which consists of an open pit mine, a leaching-solvent extraction and electrowinning process. There is also a dump leaching and a Sx-Ew plant for treating the low grade suifide ore (under the cutoff grade) from the Chuquicamata mine. Prior to reviewing the mine planning process, capacities for the Chuquicamata sulfide line were 640 000 tpd of run of mine material, 160 000 tpd of ore and 4 200 tpd of concentrate. This meant a total annual movement of around 230 Mt in the mine and a treatment of 57 Mt in the concentrator with a stripping ratio of approximately 3: 1. The old exploitation strategy consisted of an "open scheme", which means that all benches must have a berm with enough space to allow the traffic of large haulage trucks. This fact implied working with a great flexibility, but the consequences were flat slope angles. One of the reasons for using this operating practice in short term planning was that the grade consistency from the pit has always been a controversial variable. Schedules were designed to meet grade targets accurately and they were modified immediately when deviations become apparent. This reality led to working with a great deal of independent pushbacks and it required flexibility in the traffic system. The cutoff grade policy has been the same for a long time and the figure was 0.5 %CUT either for sulfide or oxide ore. This was the reason why a balance was produced between the mine and the concentrator. The mine is operated principally with benches of 26 m but in the upper part of the pit there are benches of 24 and 30 m. The main production equipment is shovels of 28 and 34 yd3 along with trucks of 200 and 240 st. Regarding the crushing facilities, there are two main systems located inside the pit and an old one in the periphery, close to a stockpile and near the concentrator. In the north part of the pit there is a crusher for waste material and in the north-east area is located the ore crusher facility. Both restrict a significant area of the pit and the mine sequence is considering to move the ore crusher again to the south-east sector where it used to be located. Relating to the waste crusher, the idea is to move it up to a bench near the surface in order to use the same conveyor belt and, at the same time, liberate an important sector. THE MINE PLANNING PROCESS The objective of the mine planning process is to develop a mine plan for the life of the deposit, in harmony and consistent with the company's goal. It includes the origin and destiny of tonnages and grades from the mine(s), along with the necessary resources to carry out this plan such as: fleet requirement, consumable goods, manpower, etc. From the financial point of view, it means to establish the cash flow for each time period of the mine life. That is. the revenue, capital investment and operating cost associated with each period of the plan. The fundamental principles involved in the mine planning pro- cess have been a controversial issue for a long time. One of the reasons for these divergent views could be produced by the difficulty of modeling a complete extraction policy for a geological re- source. This particular problem has to deal with several decision variables that are time dependent. So far, there is no mathematical formulation for managing such a problem, and the approach to solve it is based on a circular analysis combined with certain heuristic tools. So, a global model rather than a formula, requires a clear understanding of mine operations as well as economic theory and its application to a non-renewable resource. In order to manage this complex problem, the mine planning process can be conveniently split off in three stages which are conceptual, feasibility and operational planning. The characteristics of each stage are basically the timeliness in which they are developed and the kind and number of variables involved. Thus, conceptual planning is devoted to the definition of key variables like: the size of the operation, mining method, extraction se-

Jan 1, 1996

By Christian F. Baiz

The author will present a discussion of the steps which must be taken by the prospective developer of a small mining operation to establish technical credibility when seeking financial backing. Particular emphasis will be given to the differing levels of technical work (and their relative cost) which must be accomplished to supply the information necessary to satisfy potential investor groups, whether they be other mining companies, equity investors, or financial institutions such as venture capital firms or commercial banks.

Jan 1, 1981

By K. F. Unrug

The research work reported in in this paper deals with the monitoring of roof behavior in a drift mine located in Eastern Kentucky operating in the Coalburg Seam. The thickness of the seam at the monitoring site ranges between 9 and 10 feet with the immediate roof changing from sandstone to shale then back to sandstone. Shale thickness varies between 0 and 2.5 feet. The characteristics of the immediate shaly roof were monitored with 38 dynamometers which were set up in three survey lines to cover the entire range of shale distribution. The dynamometers are capable of providing accurate load readings in the range of +/- 5 pounds. To closely observe the contribution of moisture toward roof deterioration the dynamometers were set up in intake and neutral airways. A television borescoping camera was used in conjunction with the dynamo- metric instrumentations at pre- determined observation holes to physically observe and record the separation process of the shale and sandstone stratum with respect to time. Monitoring took place between January 1985 through January 1986 in order to cover a full cycle of dry and wet mine conditions associated with the seasonal changes. Analysis of the data show a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1986

By L. Zhou, D. Bahrami

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time and computer-power consuming, especially for a large-scale mine ventilation network. In this paper, a direct derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the direct derivative method were verified against the results from a traditional method. The direct derivative method has been proved to be reliable and accurate.

Mar 2, 2022

By Simon W. Houlding

This paper summarizes recent developments in computer modelling and estimation technology. Significant improvements in computational and modelling efficiencies have advanced technical computing to the stage where, for the first time, it can be realistically applied to short-term mine planning and production control. Real-time interactive grade estimation of complex shapes, volumes and grade distributions, based on immediate turn-around of production sample grades, is now possible. An added benefit is the ability to produce complete geostatistical estimates which include confidence limits. These can be incorporated into the decision making and risk assessment processes of production control. Why the need for new technology? What is wrong with the conventional methods which have sufficed for the last thirty years? The response is manyfold. They suffer from inefficient computational processes and conflicts with geostatistical theory. They are responsible for constricting the flow of information between the disciplines involved in the mine production process. Finally, it is illogical to approximate irregular geological and mining volumes with orthogonal sets of rectangular blocks. Geological materials do not occur in block formation; and mining methods which excavate rectangular blocks have yet to be developed. Other computer based technologies have evolved out of the dark ages of rectangular approximations and have successfully dealt with irregular three-dimensional geometries. It is time for computing in the mining industry to follow this example and take full advantage of available technology. To provide the necessary background, consider the basic requirements for successful implementation of technical computing within the mine production process.

Jan 1, 1992

By G. Robert Guillet

Nepheline syenite is a light-colored feldspathic rock that is used primarily as an addition to the glass batch. It is also used in ceramics and as an industrial filler. Composed essentially of the soda and potash feldspars and nepheline, nepheline syenite contributes needed alkalis and alumina to the glass composition. And because it contains a higher proportion of these oxides per unit weight, it is a formidable competitor for feldspar in northeastern North America and parts of western Europe. Nepheline-bearing rocks are not uncommon on a world scale, but few are able to be beneficiated to a composition sufficiently low in iron to be used in the making of glass. Nepheline can only form in an environment deficient in silica. Hence free silica, as quartz, is always absent in the primary mineral assemblage. Biotite, hornblende and magnetite are usually present as minor accessory minerals, and zircon, garnet, muscovite, and apatite may be present as trace minerals. Nepheline syenite is produced for glass, ceramics, and filler markets by Unimin Canada Limited at Blue Mountain, in south- eastern Ontario. Unimin acquired the former Indusmin and IMC properties from Falconbridge Ltd. in 1990. Elkem Nefelin AIS commenced production of similar products from Stjernoy Island in northern Norway in 1961. Unimin acquired this company in 1992. Nepheline has also been a byproduct of apatite mining on the Kola Peninsula for many years, and in 1951 the production of alumina from nepheline was commenced in a plant near St. Petersburg (Leningrad). There are now four plants in the Russian Republic, two smaller ones based on nepheline tailings from apatite mining and two larger and more recent plants in central Siberia using other nepheline resources. All four of these plants are integrated complexes that produce alumina for the subsequent production of aluminum metal, sodium and potassium carbonates, and portland cement. Roofing granules are produced by the 3M Company from a nepheline rock in Arkansas. In 1980 and 1989, trial shipments of nepheline syenite were recorded from new sources in Brazil and western Turkey respectively. Recent interest is also recorded for deposits in China, Saudi Arabia, and British Columbia.

Jan 1, 1994

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized using waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empirical testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicate that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate than conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

By J. J. Kellar

Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available which allow direct in-situ analysis of adsorbed layers. Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IRJIRS) with reactive internal reflection elements allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in-situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar, 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Figure 1 is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/ dodecyl sulfate, CaCO3/oleate, ZnS/xanthate, and KCl/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990).

Jan 1, 1992

By D. J. Barratt

What is meant by "Minimizing Risk"? This paper explores some of the factors encountered in plant design which can affect the success of a mineral processing plant in terms of its planned output, quality of product and recovery. Any deficiency in either one of these objectives means lost revenue at the start of a project and reduced present value for the mine life. Time is money. Related factors such as project conception, feasibility studies, capital cost and operating cost estimation and mining studies have been covered in a recent paper (1) from which material for this paper has been drawn. What follows is a discussion of the principal factors which can influence the success of a project with particular emphasis placed on processing concepts.

Jan 1, 1983

By Randall J. Weege

Nickel laterites throughout the world are similar in their gross aspects, but vary significantly in detail. The deposits occur in two separate and distinct geologic settings --those formed over ultramafic rocks which were mechanically emplaced, and those formed over ultramafic rocks that were intruded as melts. The source of the primary nickel in the parent rock may occur both as ionic replacement in silicate lattices and as nickel sulfides. Factors controlling the degree of laterization and nickel enrichment are dependent upon the parent rock characteristics as well as chemical and climatic conditions. Two chemically and physically distinct zones (oxide and saprolite) are commonly present in the laterized rock, but one or the other may be extremely thin or absent. Cobalt and copper may be present in recoverable amounts. Geologic, geophysical and geochemical methods are all utilized in exploring for these deposits. These methods are compared, evaluated and illustrated in the paper. Drilling patterns and ore reserve calculations are also discussed. In contrast to many ore deposits, processing costs are much higher than mining costs. The most efficient processing method is directly dependent upon the chemical composition of the ore. This variation in the chemical and physical characteristics of nickel laterites requires a detailed test program of the metallurgical response to representative samples and blends of ore. Detailed laboratory and bench-scale metallurgical tests are necessary prior to a full scale pilot plant test.

Jan 1, 1978

By Mike Ghassemi

It is clear that precise overground and under-ground mapping is an important factor for all designers. Due to rapid changes in underground construction, tunnel designers are increasingly in need of updating project information. This article explains the latest techniques for detecting under-ground utilities as well as underground mapping. Global Positioning System (GPS) is a very ac-curate and popular navigation and mapping system that has been used extensively above ground, but is not used for underground mapping as signals are not strong enough to pass through ground or water. Most underground techniques were developed for military applications during the first and second world wars. Later, the techniques became public. For example, ground penetrating radar was developed for the military in 1970 to be used for locating tunnels under the demilitarized zone between North and South Korea. Later, the same technique was used for detecting unexploded ordinance such as plastic land mines.

Jan 1, 2011

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By David E. Sims

Asarco has been using computer-aided open-pit mine design since 1966. The in-house developed program package includes drill-hole analysis programs, interpolation routines, and three-dimensional open-pit design programs. The financial analysis step after pit design required that a reasonably accurate schedule be produced so that a good cash flow model could assess the feasibility of a project. The manual method of scheduling was too time-consuming for feasibility work, so a computerized scheduler was required. Since no computerized mine scheduling programs existed, we requested proposals from consulting firms to develop such a program. The selection of a consulting firm, the formulation of the contract and design specifications required about three years to accomplish. The consulting firm, Systems Control Inc. (SCI), of Palo Alto, spent over one year doing the programming and testing alone. The details of the program development were reported in "Computerized Year-by-Year Open-Pit Mine Scheduling," SME-AIME Transactions, December 1974. In June of 1973 the program, which SCI dubbed Optimum Resource Extraction or ORE, was installed. Version 1 of ORE was utilized successfully on three separate properties over a period of two years. During this time it became obvious that some of the original design specifications were restrictive, and certain modifications were required. The ORE program was submitted for modification, and after one year version 2 was operational in May of 1976. The program now consists of approximately 20,000 lines of FORTRAN source statements grouped into 190 subprograms, and runs in a 450K region of Asarco's 370/148 in Cranford, NJ. The Tucson com¬puter (370/115) is tied to the Cranford computer via a 9600 baud leased T.P. line, for running mine scheduling and other large mine planning programs.

Jan 1, 1979

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By James W. Mahar

The following paper summarizes our observations on building response to mine subsidence and techniques for mitigation of building damage. The subsidence cases are located in Illinois. The general description of the geologic and mine conditions are primarily for those sites. Data on building response and mitigation measures were collected under grants supported by the Abandoned Mined Lands Reclamation Council (AMLRC) of Illinois and the U. S. Bureau of Mines, in Twin Cities, Minnesota. Case histories include pit and sag subsidence primarily beneath abandoned room and pillar mines. The majority of the paper deals with structures affected by sag subsidence. Most of the structures are one and two story homes. The first section of the paper summarizes the typical geologic and mining conditions at the sites. Building response to pit and sag subsidence follows the first section. Emphasis is placed on the behavior of concrete and masonry foundations, and wood frame and masonry superstructures. The third section describes mitigation techniques used to prevent or minimize building damage. A summary of the observations and critical parameters is given at the end of the paper.

Jan 1, 1982

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

By Ehsan Moradabadi, Debra F. Laefer

"To more rigorously address tunneling risks to above-ground structures, vulnerability evaluation of all structures along a tunnel route is required. This multi-block area along the route can be considered a district. To fully assess each structure within a tunnel’s zone of influence, a multi-block or district-level model may provide new insights as to risk evaluation and mitigation strategies. However populating such a model with the existing geometry of the built environment poses a major challenge as measured drawings are not readily available for all structures along a tunnel’s route. Cost-effective population of such a model could arguably involve remote sensing data in the form of laser scanning or photogramme-try. However even for unreinforced masonry structures, where external, above-ground geometries can be captured, without a prohibitively expensive building-by-building, in person survey many factors would remain unknown. To consider these uncertainties in an automatic way, a performance assess-ment framework is proposed. Such a framework allows a more rigorous, initial, risk quantification than is currently possible within the simple empirical models generally being used in industry when tunneling risk is initially assessed. This paper introduces (within the allowable space limits of this format) consider-ations for auto-population and application of a district-level, tunnel-risk screening tool. INTRODUCTION Challenging topography, intense urbanization and infrastructure development, combined with limited land availability and a growing awareness of environmental issues have lead to increasing usage of un-derground spaces to control aboveground traffic and provide essential services in metropolitan areas. Tunneling, however, is not without its own risks, especially with respect to aboveground structures whether it be widespread minor damage (Burland et al. 2001) or the more notable, although less fre-quent, large-scale collapses such as the 2003 Shanghai (Allianz 2015) or 2004 Singapore (Magnus et al. 2005) events."

Jan 1, 2016

By Kirk H. P. E. McDaniel, Mark T. Strever, Keith G. Jr. Wallace

This paper presents the design and installation of an underground ventilation remote monitoring and control system at the Waste Isolation Pilot Plant. This facility is designed to demonstrate safe underground disposal of U.S. defense generated transuranic nuclear waste. To improve the operability of the ventilation system, an underground remote monitoring and control system was designed and installed. The system consists of 15 air velocity sensors and 8 differential pressure sensors strategically located throughout the underground facility providing real-time data regarding the status of the ventilation system. In addition, a control system was installed on the main underground air regulators. The regulator control system gives indication of the regulator position and can be controlled either locally or remotely. The sensor output is displayed locally and at a central surface location through the site-wide Central Monitoring System (CMS). The CMS operator can review all sensor data and can remotely operate the main underground regulators. Furthermore, the Virtual Address Extension (VAX) network allows the ventilation engineer to retrieve real-time ventilation data on his personal computer located in his workstation. This paper describes the types of sensors selected, the installation of the instrumentation, and the initial operation of the remote monitoring system.

Jan 1, 1995