Search Documents

By Monica Pavlik, Thomas Wildeman

Water from the Forest Queen mine adit near Silverton, Colorado drains into a natural wetland. Because the pH of the water averages 5 and the iron concentration averages 18 mg/L, it was thought that the wetland might naturally treat the water. Of most concern with respect to the aquatic environment is zinc whose concentration averages 0.60 mg/L. Starting in October 1997, the surface waters, ground waters in the peat substrate, and the sediments in the wetland were sampled and analyzed four times over the course of four months. The adit water primarily remains as surface water where Fe, minor amounts of Al, and no Zn are removed. After the adit water enters the peat, then it is found that the pH rises to 5.8-6.5 and sulfate is reduced. The removal of Zn and A1 is caused by these two changes. However, Fe in its reduced state is quite soluble and may be remobilized in the reduced environment of the peat.

Jan 1, 2000

The exploitation of mineral deposits for economical recovery of the contained minerals has many aspects differing from other industrial or manufacturing operations. However, generally accepted principles of good organization and management applicable to industrial plants are similarly effective for mineral processing plants. A more detailed coverage of organizational structures and management techniques than is possible in this section can be obtained from many good books devoted wholly to these subjects. A few of the more readily available examples are included in the general references at the beginning of this section. The field of mineral processing encompass a wide variety of minerals, processes, flowsheets, equipment, and end products. Mineral deposits, mines, and related beneficiation plants are found in all parts of the globe, often in remote locations with no nearby support for supplies and maintenance. Available labor is frequently unskilled, sometimes primitive, and often untrained without machine and hand tools or heavy equipment experience. Such situations call for well- planned and conducted training programs covering the full range of mining-type job skills. Climates can range from arctic to tropical and from arid to extremes of rain or snow, and the mine and plant sites can be almost anywhere. However, it is often possible and sometimes necessary for

Jan 1, 1985

By Ping Zhang, Shahram Mozaffari, Andreas Ylmefors

The risk associated with mining induced seismicity and the related rock bursts has become one of the major threats to the safety and sustainability of mining at the Kiirunavaara mine. The causes of mining induced seismicity at the Kiirunavaara mine are very complex and have affected our understanding on the source mechanisms of seismicity and further the mitigation of the seismic risk. Detailed analysis of historical mining induced seismicity at the Kiirunavaara mine was conducted. The focus of this analysis was placed on the classification of large seismic events and the evaluation of the influential factors on the classified seismic events. 145 events with local magnitude larger than 1.5 that occurred between January 1, 2011 and March 31, 2021 were analyzed. For this analysis, seismic events located in the hanging wall were not included, as these have not been observed to cause large damages to the mine itself. It was found that the magnitude of the events had good correlation with the stress change in relation to the production location. The seismic events were classified as mining-front associated, ore-pass associated, mining-front and ore-pass associated and others, according to their hypocenter location. Most of the mining-front associated events, concentrated around the production levels and slightly above and below them, generally correlated with shear cracks, and most of them occurred when the ore flow between two production levels started. The numerical modelling showed that slip of the geological discontinuity, due to unclamping between hanging wall and footwall, could be the major causative mechanisms, which further supports this finding. The ore-pass associated events are located close to the ore passes. Large seismic events located between ore passes have the source mechanism of both fault-slip and non-shear, but events located at the outer side of ore passes were all fault-slip type. By checking with the ore pass scanning data, it was concluded that the most of the events located between ore passes could be pillar bursts. An elastic core concept has been then used to define a critical pillar width. The paper is not intended to be prescriptive but rather to initiate discussion of the possible classification of seismic events at the Kiirunavaara mine and to present new perspectives of the causes of the seismicity for improving the present seismic risk management.

Apr 26, 2022

By P. B. Queneau

An operating problem encountered at the Moa Bay operation in Cuba, where nickeliferous laterite ore is processed by sulfuric acid pressure leaching, is the formation of alunite and hematite deposits on the autoclave walls. The AMPX Extractive Research & Development, Inc., metallurgical laboratory (Golden, Colorado) has made substantial improvements in the Moa Bay process in the areas of metal recovery, energy consumption, and feed versatility. One of the advantages of AMAX's process is its ability to treat substantial portions of nickel- and magnesium-rich serpentine while maintaining acid utilization efficiency. The process minimizes scale formation by combining staged acid addition with vigorous agitation and 270°C operation, but does not eliminate scaling. This paper describes how advantage can be taken of MgSO4?XH20 precipitation both to inhibit alunite scaling and to disperse hematite scale within the MgSO4?XH20 matrix. Cooling the autoclave from its 270°C operating temperature down to 180°C takes advantage of the reverse solubility of magnesium sulfate. The magnesium dissolves, liberating entrained hematite, thus providing a means for control of autoclave scale with minimum process disruption.

Jan 1, 1984

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faith-fully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach which assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared using a petroleum resource estimation example.

Jan 1, 1993

By Gene R. Block

The most economical method of reclaiming land that has been mined, whether it be in urban areas or in rural areas, is when the final configuration of the mining area is that which is required by the subsequent use. Surprisingly, there are a number of examples of this situation. In the arid southwest where water production for the expanding population is a problem, many urban sand & gravel excavation areas subsequently serve as holding basins for ground water recharge. In other areas of the county where water is not in short supply, sand and gravel excavations can be planned in such a way that subsequent land uses such as parks and homesites can be enhanced by utilizing the excavated areas as a water amenity. Reclaiming land for agriculture is another example of utilizing the excavated area for a subsequent use providing the excavated area has not been mined too deep. Other than replacing the layer of topsoil on the excavated area, the final configuration of the mining area is in many cases ready for the subsequent agricultural use.

Jan 1, 1984

By S. Veeramasuneni, Qingxia Liu, Susan Dichter

Gypsum (CaSO4-2H2O) is an abundant and naturally occurring mineral. Under elevated temperatures (250 to 300°F) gypsum loses its crystalline water and is converted to hemihydrate (CaSO4 -0.5H2O). The hemihydrate form is also called plaster that is widely used in wall- board, joint compound, and many other industrial applications. At temperatures higher than 450°F (up to 1,200°F), gypsum loses all crystalline water and is converted to anhydrite form (CaSO4). The loss of crystalline water at elevated temperatures is an endothermic reaction. This property makes gypsum an attractive filler and fire retardant in certain thermosetting plastics. The applications of gypsum in plastics, food, pharmaceutical, and paper coatings will be reviewed in this paper. The future of synthetic gypsum, a by product of various industrial processes, will also be discussed.

Jan 1, 2003

By Rustyn Sherer

Curis, the name of a new Arizona-based mineral development company, is an acronym which stands for ?Cu? (elemental symbol for copper), ?r? (recovery), ?is? (in situ, the Latin for ?in place?). The company was created specifically to advance the development of the Florence Copper Project in Florence, AZ and to pursue other next generation copper development projects in progressive jurisdictions around the world. ?We are extremely excited about this project,? said Curis Resources president and chief executive officer Michael McPhie. ?We?re here to set the standard for Greenfield in situ copper recovery (ISCR) operations in Arizona and around the world. We believe in our people, our technology and our process; and we are passionate about our commitment to environmental stewardship and community development. We?re making a long-term investment in Florence, and in Arizona.?

Jan 1, 2011

By K. Lang

A test section of the upper most lift and underlying lifts of a large scale copper heap leach operation was instrumented and monitored with advanced wireline geophysics, fiber optics and resistivity electrode arrays. Elemental Capture Spectroscopy (ESC) copper measurements, resistivity measurements from an Array Induction Tool (AIT), electrical resistivity tomography (ERT) and distributed temperature sensing (DTS) with fiber optics provided integrated near real time data about the performance of the heap. During the leaching cycle, ECS provided continuous vertical measurements of copper in the upper most and underlying lifts in the test section of the heap and was used to generate a copper recovery curve. ERT inversion modeling provided high resolution 3D resistivity measurements, which were used to evaluate moisture distribution. DTS measurements of temperature were used to track the PLS front and calculate velocity. AIT induction provided highly precise bulk resistivity measurements. In-situ samplers provided PLS chemistry at multiple points. Properly integrated monitoring data can provide the heap leach operator with information that can be used to evaluate the hydrodynamics and metallurgy of the leaching process in near real time. Problems in the heap, such as pooling, channeling, longer lag and breakthrough times, excess acid consumption, increased solution in inventory, toe saturation and slope stability can be detected in near real time with the in-situ measurements evaluated.

Feb 23, 2014

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By William H. Wiese

Anecdotal reports of high rates of congenital malformations and spontaneous abortions at the Shiprock Indian Health Service Hospital in San Juan County, New Mexico prompted an interview survey, obtaining data from families of 26 former uranium miners and 30 controls. Results supported the possibility of increased fetal wastage and congenital malformations. However, definitive conclusions were obviated by methodologic limitations in terms of selection of cases and controls and interviewing technique, as well as very low numbers and lack of statistical significance. The Council of Environmental Quality (1980) published a report which singled out San Juan County, nationally, as having an extra-ordinary high rate of congenital anomalies reported from birth certificates in the years 1973-75. San Juan County is in the northwest corner of New Mexico and includes the northeastern edge of the Navajo Indian Reservation. It has been the site of uranium mining and milling and also of coal mining (Clement Associates, 1980). While much attention has been focused on lung cancer and chronic lung disease as health hazards to uranium miners, virtually no attention has been focused upon possible reproductive effects that may result from exposure to radiation. Could these reports indicate such an additional arena of health effect either on miners or on others living in the vicinity of the mines and mills? The biologic and epidemiologic literature does not lend much support for adverse genetic outcome. The UNSCEAR report (UNSCEAR, 1977) summarizes much of the existing data. For example, on the basis of many animal studies and what has been observed in atom bomb survivers in Japan, it has been estimated that mutation rates resulting from low LET radiation to paternal germ cells would be 60 X 10-6 recessive and 20 X 10-6 dominant mutations per gamete per rad. There would be a five-fold increase in the number of recognizable abortions. The doubling dose for genetic disorders in mice is estimated at 100 rads. The assumption has been that low levels of exposure, such as might be received occupationally from uranium mines and mills or environmentally will produce reproductive effects that would defy distinction from background rates. However, the possibility can not be dismissed. In man, spermatogonia are thought to be three-fold more sensitive than in the mouse. Also, the high LET radiation from alpha particles is as much as 20-fold more effective in inducing changes in meiotic and post meiotic stages of cells, compared with low LET radiation. There is some degree of localization of alpha emitters in testicular tissue after inhalation of radon and radon daughters (Blanchard, R.L. and Moore, J.B., 1971; Pohl, E., 1964). The slopes of doseeffect curves are affected by type radiation and rate of administration. Data on such curves are poorly defined and debated as to whether there may be increased or decreased effect per unit dose at low levels of high LET radiation. Increased rates of aberrations of chromosomes in peripheral lymphocytes cultured from uranium miners have been reported (Brandom, W.F., et al., 1978). At cumulative exposures of 100 working level months (WLM) or less, a range of exposure lower than the limit of current occupational standards, the aberrations were increased more than two-fold. Our interest has led us to pursue the question of reproductive effects along three separate paths of inquiry: studies of the secondary sex ratio, cytogenetic study of human sperm, and studies of rates of congenital anomalies. I will present the thrust of our findings, most of which remain preliminary, comment on their interpretation and limitations, and indicate directions needed for future research. The secondary sex ratio is the ratio of males to females at birth. In the U.S., the ratio averages around 1.05. Ratios in blacks are somewhat lower (1.025) than in whites (1.053). For American Indians, the data are less definite. Values from Oklahoma and California are similar to whites (1.05). Southwestern tribes have, as we shall see, varying levels. The theoretical effects on sex ratio resulting from irradiation of the zygote are based on the principles of sex-linked genetics, including differential effects of lethal dominant and recessive mutations on the sex chromosomes, complicated by possible non-disjunctional events. Observations have done little to clarify, confirm or refute the theories. The sex ratio of progeny of survivers of the atomic bomb showed little change (Schull, W.J., Otake, M., and Neel, J.V., 1981). Observations in children of uranium miners having been inconsistent. Most frequently cited is a study of miners in Czechoslovakia (Müller, C., Razicka, L., and Bakstein, J., 1967). Compared with children born to miners prior to the start of mining, the sex ratios of children born after the start of mining were decreased -statistically significant after correcting for birth order. The ratios in first-born children were, before the start of mining, 1.118, and, after the start of mining, .713. In the interview survey at Shiprock, the sex ratio in families of non-miners was 1.03, and in families of miners it was 0.73 (p < .05). Dr. Alan Goodman at the University of New Mexico has studied trends in the sex ratio in the general population in New Mexico and Arizona with particular reference to counties in the Four Corners area and the Navajo Indian Reservation, areas where uranium mining has been active_ His findings (unpublished) are as follows: (1) Beginning in the early 1950&apos;s, there has been a modest, but persistant and statistically significant decline in the secondary sex ratio for the state of New Mexico compared with the U.S., a decline that roughly parallels the emergence of uranium mining in the Grants mineral belt in northwestern New Mexico. (2) Data available for the 11 years since 1969 show that among the five counties with ratios significantly lower than the state

Jan 1, 1981

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By M. J. Hrebar

In the summer of 1990, a study was conducted to document large tractor (i.e., Caterpillar Dl1N) utilization in surface coal mining. The tractors were found to be utilized as primary production machines and in combination systems with blast casting and draglines and blast casting and excavator/truck systems. In addition, dozers were used to prebench ahead of a primary dragline system. The study also established ranges and averages for Dl1N operating costs and mechanical availability. Based on simulated production of various tractor dozing applications, the potential for low cost coal stripping was suggested (Hrebar, 1991). A follow-up study, also funded by Caterpillar Inc., was conducted in the summer of 1991 to determine actual production rates in two dozer stripping applications. These actual production rates would then serve as a foundation for estimates of stripping costs. This paper presents the results of the studies in a contour and a cast application.

Jan 1, 1992

By M. Gorman

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately 74 miles southeast of Las Vegas, Nevada. The property has been owned by the Duval Corporation, Cyprus Mining Company and Equatorial Mining of Australia. Mercator purchased Mineral Park from Equatorial in 2003. Mineral Park commissioned a 25,000 tpd copper and molybdenum concentrator in November and December of 2008. The process includes two stage milling (SAG and Two Ball Mills) fed by primary crushed ore. Metals are recovered in a copper-molybdenum flotation circuit consisting of mechanically agitated roughers and cleaners. The copper- molybdenum flotation concentrate is thickened and further processed in the molybdenum flotation circuit which separates the copper and molybdenum minerals into salable concentrates. The molybdenum circuit also uses mechanically agitated cells. This paper describes the plant and some of the highlights of the commissioning process.

Jan 1, 2010

By J. Sharp, R. Arnold, P. Rusin, T. Young, N. A. Sinclair

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environmentally unacceptable. Bioreductive leaching of such ore samples at MBX resulted in high extractions of silver and molybdenum. When baseline, three-day, cyanide bottle-roll tests were conducted on manganiferous-oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bioreduction with 99.8% dissolution of manganese. A followup cyanide bottle-roll test yielded an additional 8.5 % silver dissolution, for a total extraction of 94.5%. Baseline, three-day, acid bottle-roll tests of the iron-oxide molybdenum ore Yielded 1.8% molybdenum. However, bioreduction solubilized 93.3% of the molybdenum into the growth medium. An additional 0.3% molybdenum was solubilized during the followup acid bottle-roll test. Microbial treatment of refractory oxide ores with bioreductive bacteria resulted in higher extractions of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and molybdenum was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1993