Search Documents

By Andrew B. Pervis

With the ever increasing demand for Finer powders by industry there has been a continuing effort by air classifier manufacturers to improve and offer machinery capable of producing these fine powders. Common to these classifiers is the use of a multivaned rotor through which passes all of the air used to transport the particles to be classified. Rotor revolutions per minute and the amount of air passing through the rotor are the main variables in determining the particle sizes which will be able to pass through the spinning rotor. A simplified equation derived by setting the air drag force carrying a particle through the rotor equal to the centrifugal force due to the spinning rotor's action on the entering air and particle is: Diameter of Particle = [ ] Where K is a function of air viscosity, particle configuration, rotor and blade configuration; RPM is rotor revolutions per minute; M3/sec. is air quantity passing through the openings between the rotor blades.

Jan 1, 1983

By K. J. Shoop

An analysis of an iron ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency in the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Experiments were divided into two groups: 1) Drop testing, which was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. 2) Wet grinding, which was further divided into laboratory tumble tests and pilot plant scale tests. Laboratory tumble tests were performed to determine the effect of temperature on the grinding of iron ore. This was done by varying the percentage of fines and percentage of metamorphic clay material added to the iron ore grinding charge. The pilot plant scale tests were conducted as a scale-up of the laboratory tumble tests and to determine the effect of temperature on slurry rheology, and how this changing rheology affected the grinding of iron ore. The combined results of drop testing and wet grinding were used to make some predictions of the performance of plant scale autogenous grinding. In drop tests the breakage characteristics of the iron ore had no noticeable change in size stabilities for dry and water saturated samples over the temperature range studied (-25°C to 25°C). The effect of frozen pore water was not observed due to the low apparent porosity of the iron ore. The addition of fines to the test charge caused a decrease in the amount of new fines produced for both the laboratory tumble tests and pilot plant scale tests. The production of fines further decreased when tests were performed at the colder temperature. The increased energy consumption at lower temperatures was dominated by rheology phenomena. The addition of metamorphic clay material to the iron ore test charge resulted in more fines being produced in the laboratory tumble tests. This was due to the metamorphic clay material grinding easier than the iron ore. This caused an increase in the amount of fines in the mill, which in turn, would prematurely slow down the grinding of iron ore because of an increase in the viscosity of the slurry.

Jan 1, 1995

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By B. K. Mishra, B. Das, L. Panda, D. S. Rao

"The dissolution behavior of lateritic nickel ore containing 1.2% Ni, 40.6% Fe, 9.5% SiO2 and 9.59% MgO by sulfuric acid was investigated. The ore was characterized adequately by different techniques such as chemical analysis, scanning electron microscope (SEM), X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), thermal analysis and Fourier transform infrared (FTIR) spectroscopic measurements. The characterization results did not reveal any distinct mineral phase for nickel; it was associated with mineral phases like goethite, hematite, chromite and serpentine in various proportions. The beneficiation studies by hydrocyclone, magnetic separation and flotation did not enrich the nickel value. Reduction roasting followed by magnetic separation indicated only 2%Ni with 28.9% yield. Consequently, the recovery of nickel values from the lateritic ore by acid leaching under different conditions was studied. The kinetics of leaching obey the first order rate equations. The recovery of nickel was found to be influenced by temperature. It was observed that at an acid concentration of 2M, leaching temperature 363 K, time 240 min and solid-to-liquid ratio of 1:10, it is possible to leach out more than 95% Ni.IntroductionThe demand for nickel is ever increasing. Nickel is used to impart specific properties to steel, titanium and aluminium, and also is used in petrochemicals, catalysts, batteries, etc. It has been estimated that nickel oxide ores account for about 70% of the world nickel reserves. However, most nickel is sourced from sulfide ores. Nickel is extracted from sulfide ore by size reduction, followed by flotation to obtain a nickel-rich concentrate. The concentrate is then pyrometallurgically processed by smelting to produce a nickel-rich matte after discarding an iron-rich slag. Due to the increasing demand for nickel in stainless steel and other alloys, nickel is also extracted from many secondary sources. The recovery of nickel from oxide ores is now gaining momentum, and more exploitation of this ore is being attempted by advanced as well as environmentally feasible, cost-effective techniques. Dalvi et al. (2004) has reported that, due to the increase in demand, the world nickel production from laterites is expected to increase every year from the current level of production. In recent years, investigations of the use of low-grade ores, spent catalysts, clays, etc., have intensified to meet the market demand and also due to a shortage of high-grade nickel bearing ores (Al-Mansi and Abdel, 2002; Baba et al., 2009; Ismail et al., 2011)."

Jan 1, 2015

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By Michael Schultz, Gregory Sanders

In 2017, the North Texas Municipal Water District (NTMWD) initiated the design of the Sister Grove Regional Water Resource Recovery Facility (SGRWRRF) to provide additional treatment capacity for future population growth within the Lavon Lake watershed. To provide a discharge location for SGRWRRF approximately 4.5 miles of 2.4- meter (96-inch) internal diameter pipeline will be constructed, including 2.3-kilometer (7,800) feet and 487-meter (1,600 foot) long tunnel segments. This paper will discuss the anticipated geology of the two tunnel segments, selection of the tunnel alignment, the anticipated initial tunnel support requirements and other aspects of the project design

Jun 13, 2021

By MEHMET ALI RECAI ONAL, MAHMUT CAMALAN

The key motivation of this study is to evaluate the potential of well-known hazardous gases—carbon dioxide (CO2), hydrogen (H2) and oxygen (O2)—as grinding aids for mineral liberation in ball milling. The results show that exposure of chromite ore particles to CO2 flow will promote chromite liberation at breakage and, therefore, using CO2 as a grinding aid may partially reduce the carbon footprint of the mining industry. For that purpose, the use of two-phase (gas–solid) or three-phase (gas–solid–water) moving-bed mixers are recommended for the pretreatment of mill feed before ball milling.

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

Stillwater Mining Company (SMC) has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The most recent TBM used is for the Blitz Project, where a 5.5m (18ft) diameter main beam unit, commissioned in Q3 2012, is being utilized to drive a 6,975m (22,500 ft) ventilation and haulage level East of the Stillwater Mine for the Blitz expansion project. The assembly/commissioning of the TBM, institution of the planned diamond drilling program, application of ground control systems, and the current tunneling metrics will be covered.

Feb 23, 2014

By R. L. Taylor, S. D. Abbott

"INTRODUCTION Mines are filled with a mixture of gases, some of which are toxic, flammable, explosive. Others can be early reporters of potential problems. It has previously been shown that analysis by gas chromatograph can the most accurate conventional analytical tool for common mine gas mixtures when used correctly. There are some other detection methods (e.g hand held sensors), but they do not detect many situations which are immediately dangerous to life or health (IDLH). Examples include explosive hydrogen mixtures, toxic carbon dioxide levels, and some explosive mixtures of methane with oxygen. (Reference our previous paper). There are several reasons for mines to consider onsite GC analysis. (1) Timeliness of results. Samples can be taken and analyzed immediately. Samples do not have to be shipped to a lab and wait for results. (2) Ability to run greater number of samples a lower for the same cost. This allows mine to increase the number of samples taken to be more informed about the gases/conditions of the mine without the worry of financial constraints. (3) Fewer sample media needed, and there is no wear and tear or cost from shipping them offsite. When samples are shipped offsite, those sample media cannot be used to take until the lab returns them when the analysis is done onsite, the sample media can be used again almost immediately. However there are several challenges associated with using GC to analyze mine gas samples onsite. To date there has been a clash of the requirements for a successful analysis, the capabilities of the technology, and the practicalities of implementation. The purpose of this paper is to discuss some of the difficulties in getting accurate reliable data and doing so in an economic way. This whole measurement activity is a cost center for a mine, so there are economic concerns for the mine to address. These concerns are mainly staffing costs, capital costs, maintenance, and consumables costs. A properly staffed and equipped analysis lab, including burdened overhead, costs about $500K per year. At a sampling rate of 10 per day, this is about $140 per measurement for a proper onsite lab."

Jan 1, 2016

By Stephen H. Stow

Economically important heavy minerals have been studied in the sediments of offshore Alabama and Mississippi. Sandy samples have been collected from a 200 square mile area from Dauphin to Horn Islands. The minerals concentrate in sediments under 10-35 feet of water and may reach 2.4% by weight. The distribution of total heavies is related to the hydrodynamics of offshore Alabama-Mississippi; the greatest concentrations are in the Gulf where the longshore current is diverted from its westerly flow. Preliminary observations indicate that the distribution of individual minerals can be correlated with wave energy, particle size, specific gravity, and morphology of the mineral grains. The coarser, lighter minerals--kyanite, sillimanite and staurolite--are concentrated in relatively low energy areas in the Mississippi Sound and at the end of Dauphin Island in the Gulf; maximum concentration for each is 34.5%, 6.0% and 43.2%, respectively, of the heavy minerals. The smaller, more denseminerals--ilmenite, rutile, leucoxene, zircon and monazite--are concentrated in high energy areas in the Gulf; maximum concentration for each, respectively, is 42.0%, 5.9%, 9.652, 10.7% and 1.3% of the heavy minerals. On the basis of a minimum concentration of 1% heavy minerals, two areas have been identified and the total amounts of different minerals have been calculated to a depth of 25 feet of sediment. The data are preliminary and in no way indicate recoverable reserves, but they do show that on the order of 20 million tons of heavies exist. These deposits should be termed "indicated resources".

Jan 1, 1975

By Mortimer J. Richardson, Earl H. Malmstrom

INTRODUCTION The art of placer gold mine evaluation and mining has had an interesting evolution beginning in earliest times. DE RE METALLICA (c.1556), documents the use of rockers, circular sieves(jigs) and riff lest for classifying, concentrating and recovering placer gold, respectively. During the late 1800's in the heat of the international gold rush, a bucket ladder mining dredge containing its own processing plant was developed that enabled digging of placers to bedrock that were inaccessible to the hand miner. The power driven churn drill was developed at about the same tie that facilitated more rapid and larger scale sampling of placers to bedrock. The mineral jig was applied in the early part of the 1900,s to begin the replacement of riffles on placer dredges. Mining dredges proliferated in California and New Zealand to mine the deeper placers and spread throughout the world. The companies that were leaders in dredge mining technology conducted experimental work that advanced the state of the art by processing of gravels with jigs and amalgam systems to recover gold on board dredges in a continuous process. This paper will synthesize the technology of placer gold exploration, mine development and operation into guidelines for evaluation and development of small-scale prospects. Prospect Reconnaissance The location of a prospect usual1 y results from some physical evidence of the presence of gold and/or past mining activity. Any earlier activity that may have produced gold from the prospect, should be investigated before making the trip. The initial reconnaissance should attempt to verify a near-surface presence and then make observations concerning the geomorphic characteristics that relate to placer gold accumulation. Estimates of the probable depth, breadth and length of mineable gravels can be made from the surf ace by the experienced placer mining engineer. With this information, he can speculate on whether there is a viable prospect to be pursued. The placer mining engineer should be experienced in panning samples found in shallow diggings or from existing pits. This will give him immediate indications of gold presence without fear of "salting" by an over-ambitious promoter of the project. The same capability of panning is important during the other sampling phases. A thorough knowledge of logging and calculating the results is essential to proper evaluation of the deposit' s tenor. Evaluation Methods Depending upon the character of the prospect such as river, benches, terraces, jungle, the type of equipment to conduct sampling of the deposit must be determined. In most cases, the drill has replaced bulk sampling. The churn drill has had the greatest amount of accumulated experience but is slow. The reverse circulation drill (RC), is limited by its lack of verification in subsequent mining in order to prove its reliability. However, in the hands of knowledgeable placer mining engineers experienced with its use and calibration, it may be used. The RC Hammer drill (such as the Becker), can be as much as ten times faster than the churn drill and compress the time necessary to prove a prospect, or, to disprove it. All costs in balance, it is often cost effective over the churn drill.

Jan 1, 1987

By Keith G. Wallace

In 1982 the U.S. Congress passed the Nuclear Waste Policy Act (NWPA) to provide for the development of an underground repository for spent nuclear fuel. This development will be managed by the United States Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository; those sites were: 1) A site in volcanic tuff located at Yucca Mountain in Nevada, 2) a site in bedded salt located in Deaf Smith County in Texas, and 3) a site in basalt located in Hanford, Washington. At present conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation system designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be re-established to allow re-entry into previously closed rooms for the purpose of inspection, maintenance or retrieval.

Jan 1, 1987

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By Robert F. Conley

Attrition milling, once employed exclusively for the dispersion of pigments, has in recent years found a host of new applications in the area of mineral processing and mineral-pigment production. Broadly categorized, attrition milling is divided into two classes, as defined by the machinery's function, vibratory milling and rotational milling. Each mill type has been defined as a variation on ball milling and the terms, "vibratory ball mill" and stirred ball mill" appear in the literature. The primary design differences between attrition and ball mills are: (1) a stationary canister (or shell) (2) smaller grinding media (3) grinder energy is motor limited rather than gravity limited (4) strong media/feed size dependance.

Jan 1, 1983

By J. Mark Richardson

Modern mining operations are increasingly affected by complex economic factors. Broad and rapid fluctuations in metal prices, rising operating costs, socio-political trends and the inherent technical difficulties encountered in most operations, all can combine to quickly change once-profitable ventures into money-losing propositions. Accurate knowledge of metal inventories during all phases of an operation has become essential to wise management decision-making. This paper reviews key elements of metallurgical accounting: sampling theory, measurement technology and computerized data adjustment. Application of current technology to the reconciliation of a hypothetical operation is discussed.

Jan 1, 1991

By Paul Soros

There has been a steady increase in shiploading capacities in the last 20 years. One of the reasons has been the general increase in ship sizes, with the largest vessels currently around 280,000 DWT in the bulk trades. Obviously, the large vessels can accept loads faster and their economic utilization justifies higher loading rates, up to a point. The high capacity facilities have loading rates far beyond this point. The economic logic of these facilities is based on the fact that for a given annual throughput the capital and operating cost of a single high capacity system is less than that of two smaller systems. Thus, where the projected throughputs are large, there is a great incentive to reduce capital costs by maximizing capacity. Tubarao, in Brazil, designed for a 100 million ton per year throughput with one finger pier and one high capacity berth is a successful demonstration of this approach. In the current state of the art, the high capacity systems have shiploading capacities in the range of 10,000 - 16,000 TPH, for annual throughputs of 20 million tons and larger per loading berth.

Jan 1, 1982

By William Gleason

"Speakers and attendees of the 2016 Cutting Edge Conference could not be faulted for keeping one eye on the presentations taking place at the Hyatt Regency at LAX in Los Angeles, CA on Nov. 7 and 8 and another on the results of the historic election in the United States that took place on Nov 8. While there was certainly interest in the presidential campaign, there was also a great deal of interest in Measure M on the California ballot. Measure M, which passed easily, is a half-cent sales tax increase that will fund the most ambitious transit expansion in Los Angeles County history.In the coming years, the ballot measure will transform a traffic-choked region by funding the construction of nearly a dozen new rail lines with an estimated $120 billion raised in four decades. Among the projects that could come to fruition are a twin-rail tunnels project through the Sepulveda Pass and new connections in the city.During the update on West Coast projects, Bill Hansmire summed things up with a slide asking “How much work is there on the West Coast,” and his answer was “Billions.”From Seattle, WA south to Los Angeles, there is already a lot of work for tunneling and underground construction experts, and Measure M ensures that there will be plenty of work for decades to come.Currently, The Los Angeles County Metropolitan Transportation Authority (Metro) has three rail projects underway that were funded by Measure R in 2008 — the Regional Connector, the Purple Line subway extension and the Crenshaw/LAX Line that are designed to alleviate the traffic pressure with an eye to more solutions.Measure M is the fourth sales tax increase to fund transportation in L.A. County, bringing the base sales tax rate to 9.25 percent. In some cities, which already levy their own sales tax, the rate would be higher, The Los Angeles Times reported.About 35 percent of the revenue will fund major new transit projects, such as the subway under the Sepulveda Pass, extension of the Gold Line to Claremont, extension of the Crenshaw Line to West Hollywood and acceleration of the Purple Line Subway construction along Wilshire Boulevard to finish in 2024, 10 years earlier than scheduled.About 17 percent would fund a dozen highway improvement projects, such as widening parts of I-5 in the Antelope Valley and southeastern county, adding bus lanes to the Sepulveda Pass section of the 405 freeway and adding truck-only lanes to a section of the 710 freeway."

Dec 1, 2016

By Fiona M. Doyle Garner

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°-200°C. Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions of various metals, singly and in mixtures. Single solutions of Fe, Xi, Cu, Mg, and tin precipitated aFe2O3, Ni(OH)2, Cu2O, Mg(OH) 2 and ?Mn203 respectively during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe20k. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versa- tic solutions are similar to those for iron hydrolysis in aqueous solutions. Infrared spec- troscopy and thin-layer chromatography of mixed iron-nickel Versatic solutions indicated that mixed Fe-Ni carboxylate complexes are present. Magnetic interactions between mixed complexes are thought to be responsible for the homogeneous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1984