Search Documents

By David Mast, Irwan Halim, Seung Han Kim

Nowadays more infrastructure tunnel projects are procured using design-build method. In this environment, the Owner’s engineer would typically provide performance requirements for the design-builder, and the Contractor’s designer would work with the contractor to design the tunnel lining based on the Contractor’s means and methods and manufacturing process. This paper will describe the typical requirements provided by the Owner based on its design objectives, and the means and methods by the Contractor that would significantly impact the design. Project examples and recommendations for Owner’s requirements will be provided that can optimize the design and still achieve the Owner’s performance objectives.

Jun 13, 2021

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By M. Kuchta, S. Iverson

INTRODUCTION Underground blasting with perimeter damage control can reduce the requirement for loose rock scaling and reduce the risk of ground-fall injury. In previous work Johnson and associates (2010) from the National Institute for Occupational Safety and Health (NIOSH) developed a rock blasting perimeter damage and control design method included in the DRIFT software tool (NIOSH, 2018). This blast design software tool utilizes current methods of perimeter blasting with the added design element of a buffer row coordinated with the perimeter row to reduce perimeter damage. The coordination is in applying one of several blast damage models to calculate the damage extent for each production, buffer, and perimeter blast hole in the design. The calculated damage is then applied to the spacing between the blast holes. The basis of the buffer row design is the practical damage limit and is supported in this paper with computer models of signature blasts and full blast rounds using PFC2D (Itasca Consulting Group, Inc., 2018). Practical damage limit The practical damage radius (Rd) is not to be confused with burden. The practical damage extends toward the burden side and inward into the rock mass. For all practical purposes, the practical damage radius equals one half the burden (Hustrulid, 1999). The maximum extent of radial crack damage around a blast hole (Rcrack) and the maximum extent of radial crushing damage (Rcrush) are illustrated in Figure 1. A “practical” radius of damage (Rd) lies between the crushing limit and the cracking limit. The “practical” damage means that if the rock mass lying outside of the practical damage circle were removed, the rock remaining within the circle would easily break apart. Blast pressure and strain Work by Johnson (2010) and associates included signature blast tests in large concrete blocks. A signature blast test in concrete as exampled by strain data in Figure 2 was designed to monitor the dynamic strain at incremental distances from a single fully coupled blast hole, measure crushing and radial cracking extent by wire-sawing to expose the damage, and relate the damage to overbreak that is common in underground blasting. The initial slope or rising strain as the stress wave passes by the strain gages shows very high strain and strain rates close to the single blast hole. Since the derivative of strain versus time is strain rate, a line tangent to each of the strain curves at the maximum strain rate is drawn and the strain rates identified. The high strain rates were then plotted on a semi-log in Figure 3 to show a linear trend. The strain rate is greater than 100 s-1 within 20 cm from the blast hole for the signature blast experiment. The strain rate at the blast hole wall is projected to be 300 s-1. Figure 4 illustrates the damage in the NIOSH block exposed by a wire saw cut.

Jan 1, 2019

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By Ren Xiangwen, Shi Xuefa, Shao Mingjuan, Ye Jun, Yang Yaomin, Li Bing

"The Mid-Atlantic Ridge (MAR), one of the archetypes of slow spreading ocean ridges, extends from the Arctic Mid-Ocean Ridge southward to the Bouvet triple junction making up a significant proportion (~ 40%) of the global oceanic ridge system. During the past few decades, many hydrothermal fields like TAG, Logatchev, Ashasze were discovered along the northern part of the MAR, whereas the southern part, which makes up one third of the ridge (6000km), shows little documentation of hydrothermal mineralization, except for three sites: Site 4°48! the Nibelungen Field, and Lilliput. During March to May 2011, following discovery of three new hydrothermal fields during the 2nd Leg of COMRA's 22 Cruise of the R/V DayangYihao, the 3rd and 4th Legs found another two high temperature hydrothermal fields (SMAR15°S, SMAR26°S), one low temperature field, and several fields with strong turbidity and temperature anomalies in the water column. In this study, we present a preliminarily study of the mineralogy and isotopic geochemistry of the sulfides from SMAR 15°S and SMAR26°S.SMAR 15°S is situated in a SE-NW offset depression of an axial neovolcanic ridge in the median valley, with water depth of about 2793m. In the water column around this field, strong turbidity and temperature anomalies were detected. Ten-meter tall venting chimneys, hydrothermal mounds, as well as a large amount of hydrothermal vent shrimp were also observed and recorded by ROV and deep-tow camera surveys. The samples collected from this field include sulfide chimney fragments, massive sulfides and basaltic rocks. Based on the major metal and the mineral assemblages, three types of sulfides have been identified: 1) Zn-Fe rich sulfides with abundant wurtzite and pyrite zoned fragments, 2) Cu-Fe rich sulfides with much isocubanite and pyrite assemblage, 3) Fe-rich sulfide with massive pyrite fragments. These indicate that this field has undergone at least three phases of mineralization during the venting history."

Sep 1, 2014

By Frederick A. Mumpton

Recent findings by medical workers on the association of certain zeolite minerals with the high incidence of pleural mesothelioma in two small Turkish villages have caused considerable excitement both in medical circles and in the synthetic and natural zeolite businesses. The 42 cases diagnosed between 1970 and 1977 in one community of 600 population in a region of altered volcanic tuff represent a virtual epidemic of this rare malignancy which normally strikes only about one person in a million. Cancer workers around the world expect that detailed environmental and epidemiological studies of the disease in these areas will shed considerable light on the cause of this particularly lethal form of lung cancer. Scientists and engineers developing uses for zeolite materials in industry and agriculture, however, are justly concerned that the preliminary results available on this situation will be used by environmental and regulatory organizations to label an entire group of miner- als as carcinogens on the basis of what is little more than circumstantial evidence. Although there is no question as to the large number of cases of mesothelioma in these areas of central Anatolia, the work to date has suffered from a lack of sound geological and mineralogical input. Ataman (1) stated that a "correlation" exists between mesothelioma and zeolites in this region; however, the geological data needed to document a direct relationship between the presence of zeolites in the volcanic tuffs surrounding the villages in question and the rate of malignant lung disease in the inhabitants have g been obtained, nor has evidence that suggests a cause-effect relationship between zeolites and cancer been reported. To provide fundamental information on the distribution of zeolite minerals in areas of central Turkey where high incidences of pleural mesothelioma have been reported and to evaluate from first-hand knowledge the published reports and news releases of medical workers engaged in assessing the problem, the following investigation was made.

Jan 1, 1979

By K. Boakye

This paper presents the results of a review of historic blast design practices at the Dragon Products Company, LLC (Dragon) Quarry Operation, along with the results of two different blast design vibration monitoring programs. A blast pattern design modification was initiated to determine if production volume per shot could be increased and highwall instability could be decreased. A vibration monitoring program was undertaken to investigate peak particle velocity (PPV) and relate the data to the blastability of the jointed onsite rock mass, utilizing the relationship between PPV and dynamic stress and strain. The Dragon Quarry Operation has historically used a 6-in. diameter, 14-ft by 14-ft production blast pattern, with blast holes loaded manually using cartridge style explosive products. In 2011, Quarry Operations introduced a 6-in diameter, 16-ft by 16-ft production blasting pattern, using pre-mixed, truck-loaded, bulk emulsion/ammonium nitrate/fuel oil (ANFO) blends. This paper summarizes the results of the blast design modifications, the results of the vibration monitoring data, and describes how production blasting and excavation at the Dragon Quarry has benefited from such modifications.

Feb 27, 2013

By Andrea Koschinsky, Akira Usui, Michael Bau, Katja Schmidt, James Hein, Thomas Kuhn

Marine ferro-manganese (Fe-Mn) crusts and nodules are metal-rich chemical sediments that are archives of paleoceanographic proxies and potential metal resources and targets of deep-sea mining. Traditionally, crusts and nodules are subdivided into hydrogenetic, diagenetic, and hydrothermal types. While hydrogenetic Fe-Mn crusts are a potential resource for Co, Te, Pt, and REY, nodules are enriched in Cu, Ni, Mo, and Li, and hydrothermal deposits may be enriched in individual metals such as Mo, Ba, and Li, depending on the temperature and composition of the hydrothermal fluid. The different types of marine oxidic Fe-Mn precipitates, therefore, have different economic potential. Hence, a robust classification is not only helpful in the general geochemical characterization of such precipitates (and as such is a useful teaching tool, for example), but may also simplify the evaluation of their importance as a potential metal resource, which helps to prioritize exploration targets for deep-sea mining.

Sep 1, 2014

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By M. S. Celik, H. Du, J. D. Miller, F. Cheng, O. Ozdemir

"In this paper, recent progress with respect to the flotation chemistry of soluble salt minerals is reviewed, and some of the more relevant issues including the hydration states of ions, the interfacial phenomena of salt surfaces and the flotation behavior of selected soluble salts are discussed. Due to the high solubility, the flotation of most soluble salts has to be carried out in their saturated brines. Anecdotal evidence has suggested that the hydration states of the ions have significant influence on the physicochemical properties of the solutions, the surface charge and wetting characteristics of the minerals, the collector adsorption states and, further, the flotation behavior of the soluble salts. In this regard, reviewing past research findings, efforts are made to establish a correlation between the ion hydration states with the flotation behavior of the soluble salts. Further, advances in understanding the significance of colloid adsorption involved in the soluble salt flotation process are addressed, and future research efforts to understand the soluble salt flotation chemistry are suggested.IntroductionSoluble salt minerals are essential raw materials for the production of a variety of commodities, fertilizers, potassium hydroxide, soda ash, magnesium compounds and other chemicals. These soluble mineral resources can be processed using flotation technology and, currently, more than 80% percent of the world’s potash is produced by the selective flotation of KCl crystals (sylvite) from other salt crystals, predominately NaCl (halite) and other more complex salts (Searls, 1990). Despite the successful application of flotation technology in the potash industry, the mechanisms for collector adsorption on soluble salts have not yet been fully understood and, therefore, have been of considerable interest to flotation researchers for many decades."

Jan 1, 2015

By G. Mei

"This study explores froth flotation and selective flocculation methods to recycle waste phosphors containing several rare earth elements, namely, yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb). The effects of the presence or absence of collector and of flocculant and their dosages, as well as the pH, were investigated. Reverse flotation resulted in concentrates with grade of 27.03 percent and recovery rate of 71.36 percent, while flocculation resulted in concentrates with grade of 31.43 percent and recovery rate of 91.28 percent. The flotation and flocculation behaviors were further analyzed by X-ray diffraction analysis, zeta potential measurements, particle size distribution and other methods. The successful separation of rare earth minerals by flotation was attributed to the selective adsorption of the collector onto quartz, making it particularly recoverable by reverse flotation so as to be separated from the valuable materials. The analysis of the particle aggregation process indicated that its better flocculation performance was due to the selective adsorption of flocculants onto the unwanted materials, enlarging the flocculant sizes by forming aggregations and facilitating the separation of rare earth minerals from waste materials based on different settling rates. IntroductionBecause waste phosphors pose the problems of heavy environmental burden and high risk to human health (Hu and Cheng, 2012) as a result of containing heavy metals such as mercury and manganese (He et al., 2006; Lucas and Emery, 2006), they have received added attention as urban mining resources for extracting rare earth elements (REEs) like yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb).At present, chemical processes such as acid leaching, alkali fusion, roasting and extraction are the primary methods for recovering REEs from waste phosphors (De Michelis et al., 2011; Li et al., 2012; Li, 2010). With these strategies, phosphors can be effectively decomposed and their REEs extracted. After the removal of impurities, the REEs can be efficiently precipitated by adding an H2C2O4 solution (Porob et al., 2012). Although relatively high recovery rates are achieved, those processes entail high energy consumption and can cause severe environmental pollution."

Jan 1, 2017

By Raquel Costa, Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, Ana Filipa Marques, Andreia Afonso, Maria Ana Martins, António Calado, Luísa Pinto Ribeiro

Since its formation in 2004, the Task Group for the Extension of the Continental Shelf (EMEPC) has been collecting hydrographic, geological and geophysical data to support the extension of the continental shelf beyond 200 NM. In 2008, the EMEPC acquired a 6,000 m rated ROV named "Luso" and has been cooperating with several national and international institutions to increase and improve its operational capabilities to conduct research on deep-sea minerals. The Portuguese continental shelf corresponds to a broad area of the seafloor encompassing different physiographic domains: the mid-Atlantic ridge system, abyssal plains and numerous seamounts. From 2008 to the present, the mid- Atlantic ridge and seamounts have been the most visited sites with the ROV "Luso". Several hydrothermal vent sites are known to occur along the mid-Atlantic ridge to the south of the Azores archipelago and mostly within the Portuguese EEZ. Vent fields were also discovered in the extended continental shelf, namely the Rainbow and the Moytirra sites located to south and to the north of the Azores archipelago, respectively. The most studied seamounts correspond to those forming the Great Meteor chain and the Madeira- Tore rise. All these visited sites are related either with the occurrence of polymetallic sulphides or cobalt rich Fe-Mn crusts and the opportunities to further pursue their exploration will be discussed.

Sep 1, 2014

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By D. R. Gagnon

Mining companies are continually looking for product-ivity and efficiency improvements with their equipment to reduce operating costs. This paper will review the results of a productivity analysis conducted at the Luscar Ltd. Boundary Dam and Bienfait mines near Estevan, Saskatchewan using a Computer-Aided Earthmoving System (CAES) installed on a track-type dozer. The CAES TTT system is a Global Positioning System that provides the operator with constant survey guidance. The study includes a productivity comparison between two similar test sites, one with the aid of the CAES system and the other, without. The CAES TTT system shows a productivity improvement of between 20 and 35% in the reclamation slope leveling application. Even with the CAES TTT system deactivated, some of the advanced features of the system were used to: retain terrain data for volume calculations; track the equipment position; and, accurately record and separate idle time from working time.

Jan 1, 2002

By Eduardo M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond grindability data and the operating work index is presented. The objective has been to produce a sand cyclone overflow containing not more than 6% +65 mesh. However, this has never been attained even at low milling rates. On the other hand, significant improvements in throughput were achieved by instituting some equipment changes and process modifications within the grinding circuit. The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1983

By J. S. Peterson

Occupational noise-induced hearing loss (NIHL) has been recognized by the National Occupational Research Agenda (NORA) as the most common job-related disease in the United States. Roughly 30 million workers are exposed to excessive noise levels or toxins that are potentially hazardous to their hearing. The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR)is investigating noise controls to reduce operator overexposures caused by haul trucks used in underground metal/non-metal mines. To identify the most significant contributors to the overall sound level, Source Path Contribution (SPC) analysis was conducted. Noise dosimetry and time-motion analysis were also conducted to quantify operator noise exposure. SPC analysis determined that, under high idle conditions, a source near a hydraulic pump mounted to the rear of the engine and the engine cooling fan were the major noise sources. The time-motion/dosimetry analysis showed that the operators accumulated more than 90% of their noise exposures while they were hauling ore to the dump site and traveling back to the load site unloaded.

Jan 1, 2012