Search Documents

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By Pafos Busch, Martin Fischer, Johannes Jaeger

The Spitzenberg Tunnel is a 600 m (1,970 ft) long twin tube motorway tunnel on Germany’s Autobahn A44 between Kassel and Eisenach. Since flexibility was considered to be very important in the continuously changing geological conditions, NATM was chosen as the construction method. When passing an old quarry with only 1,80 m (6 ft) of overburden, the excavation works became extraordinarily challenging. This paper not only describes the special methods, like double sidewall drifts and pipe umbrellas applied in this zone but also highlights the cooperation between the parties involved, which in combination made the project a joint success.

Jun 13, 2021

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Cold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 9 million tons of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 1.0 million tons per year. Careful evaluation of the combined results of successive sampling projects has established the pit plan, mineable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1984

By Stephen H. Stow

The relationships between the amount of light reflected off 21 samples of Florida phosphate and the chemical, composition of the samples were examined. It was found that the reflectivity of a rock is directly related to its chemical composition and that darker phosphates (less light reflectance) have relatively high amounts of iron, organic C and sulfate while lighter-colored rocks were rich in phosphorus, fluorine and aluminum. The use of reflectivity measurements could have economic applications in the phosphate rock industry: color specifications for rock shipments could he met, beneficiations by optical sorting could be performed and semi-quantitative analyses could be made rapidly and inexpensively.

Jan 1, 1971

By C. A. Rowland

The use of the Bond Work Index to size industrial grinding equipment is well known. Its use to measure grinding efficiency was presented by C.A. Rowland, Jr. at an AIME meeting in 1976. However, due to a bureaucratic error, the paper was never submitted for publication. This metric has nevertheless been adopted by industry as a widely used standard. The purpose of this paper is to re-present and update the application of this tool as a standard for measuring grinding circuit efficiency. Definition ?standard, n. something established for use as a rule or basis of comparison in measuring or judging capacity, content, extent, value, quality, etc.; as standards of weight and measure? (Webster, 1958).

Jan 1, 2008

By K. J. Hartman

The term kaolin is derived from "kauling". a Chinese word meaning high ridge, which was the name of a hill in China where kaolin was first mined several hundred years ago.(1) Other common names used today for kaolin include "clay" and "China Clay". The former word technically has a broader meaning and could refer to various types of clays such as bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin as described above but could also be due to a significant historical use in ceramic applications. The terms "kaolin" and "clay" will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's widespread industrial usages center on the mineral's (kaolinite) physical features of good color, low viscosity and inertness. Kaolin is described as a hydrous aluminum silicate with approximate composition Of 2H20.A1203.2Si02. As will be shown later, a new version of the product, calcined clay with modified hydration content, is gaining widespread usages. Components of any particular kaolin in addition to alumina and silica are viewed as impurities. The more valued deposits and, hence, higher priced kaolin products are those of highest purity.

Jan 1, 1986

THE QUARTETTE Mine near Searchlight, NV, a mine that first operated in the 1890s, could begin processing ore again by September. Jetco Enterprises Inc. plans to work through the tailings and ore close to the surface followed by plans for an openpit mine. It is one of at least three new mining efforts in the region, the Associated Press reported. Another is north of Searchlight, with yet another across the Colorado River in Arizona, east of Bullhead City. Gold mining is rare in southern Nevada. The area generally lacks the rock type that contains gold deposits. Restrictions on federal wilderness areas and protections for the desert tortoise also play a role. Gold veins in the region are generally small and erratic in length and height, Bill Durbin, a geologist and chief of southern Nevada operations for the Nevada Division of Minerals told the Associated Press. L.R. Tad Tinnell, president of Jetco Enterprises, has long eyed the mine. From 1993 to 1995, he explored and drilled on the property, which was still owned by Searchlight Mercantile.

Sep 1, 2013

By T. J. Batchler, K. M. Mohamed, D. F. Gearhart, R. K. Zipf

Seals are explosion-resistant structures built in underground coal mines to isolate abandoned mining areas from the active workings. An equivalent single degree of freedom (SDOF) method such as the single-degree-of-freedom blast effects design spreadsheet (SBEDS) developed by the U.S. Army Corps of Engineers can be used to design seals to resist mine explosions. The critical input for the SDOF code is the seal resistance function. The objective for this study is to develop engineering data for design of plain concrete (PC) and reinforced concrete (RC) seals using finite element (FE) models. The FE models can then be used to generate resistance functions for different PC and RC seal designs, which can be used in the SDOF codes. The U.S. National Institute for Occupational Safety and Health (NIOSH) researchers designed and built a test fixture for use in conjunction with NIOSH’s Mine Roof Simulator to apply a four-point bending load on the face of the tested seal. Eight large-scale experiments for each PC and RC seal were conducted. The experimental design considered the effects of the foundation strength, hitching and roof-to-floor convergence. Calibrated FE models for PC and RC seals were developed using ANSYS Ver. 13. With a very limited number of engineering-based assumptions and a single set of data—including Young’s modulus, compressive strength, stress-strain relationships, etc.—the PC and RC seal models successfully calculated the recorded resistance functions and failure patterns for a wide range of boundary conditions. Plug and RC seals were assumed for a 1.83-m- (6-ft-) high entry to demonstrate the application of the calibrated finite element models for calculating the resistance functions of these seals. The resistance function of a particular plug seal case was found to be a bilinear relationship. The resistance function of a particular RC seal without shear reinforcement was found to be a nonlinear relationship.

Jan 1, 2013

By C. Frenzel

Tunnel boring machines (TBM) utilize disc cutters as the primary means for excavating hard rock. Depending on rock excavatability and rock abrasivity disc cutters can exhibit significant wear. A detailed analysis has been carried out to characterize failure modes and wear patterns of disc cutters. The relationship between rock properties, op-eration of the TBM, and failure modes of cutting tools is clearly high-lighted. On that basis a prediction tool for disc cutter consumption has been developed that allows to estimate not only gross cutter life, but accounts for cutterhead design, premature cutter changes, and disc cutter repair costs.

Jan 1, 2011

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By T. O. Llewellyn

The Bureau of Mines, U.S. Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8 to 10.2 percent P205 and 1.7 to 1.8 percent MgO. Chemical analyses of sized fractions indicated that no pebble concentrate (plus 1.2 mm) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid-fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0 to 31.3 percent P205 at flotation recoveries ranging from 72.4 to 96.1 percent of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36 percent. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3 percent P205 and 0.55 percent MgO could be produced with a flotation recovery of 89.9 percent. The MgO content of concentrates obtained from the Manatee No. I and Hardee samples was 1.20 to 1.36 percent, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 percent, but with a concomitant loss in phosphate recovery.

Jan 1, 1983

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By M. S. Moats

In the 1990?s, Técnicas Reunidas developed the Modified ZINCEX® Process to recover zinc from ores and secondary materials. The heart of this process was the use of solvent extraction to produce purified zinc electrolyte instead of traditional zinc dust cementation. This development was commercialized by Reunion Mining and Anglo American for primary ore at the Skorpion mine in Namibia with the first SHG zinc produced in May 2003. Horsehead Corporation through Horsehead Metal Products, Inc., its wholly owned subsidiary, is presently commercializing the MZP for the treatment of Waelz oxide. This paper will review open source information about the lessons learned and process modifications that have occurred at Skorpion over the past decade. It will also provide an update on Horsehead?s facility being constructed in Rutherford County, North Carolina.

Feb 23, 2014

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By Yonghong Qin, Songbo Ma, Qi Zhang, Peng Gao, Jianwen Yu

Herein, the coal-based reduction was proposed to utilize the ferronickel slag of Jingchuan company. An excellent index with metallization rate of 99.22%, iron grade of 77.91%, and iron recovery of 92.79% was obtained at carbon addition coefficient 2.0, reduction temperature 1573 K, reduction time 60 min, the particle size of coal and ferronickel slag − 2.0 mm, and CaO content 15%. The 2FeO·SiO2 was reduced to Fe and SiO2 with the increase of temperature. The CaO could promote the reduction of iron oxide. Most of the sulfides (Fe, Cu, Co, and Ni) in the sulfonium were reduced to metal. The reduction degree increased with the reduction time and reduction temperature. The higher reduction temperature represented the higher peak value of reduction rate and the shorter time of reaching the peak value. The isothermal reduction process included three stages: early stage, middle stage, and late stage. The mechanism function were f(α) = 1/2(1 − α)3, f(α) = 3/2(1 − α)4/3[(1 − α)−1/3 − 1]− 1, and f(α) = 4(1 − α)[− ln(1 − α)]3/4, respectively. The activation energy of three stages was 183.498 kJ·mol−1, 420.077 kJ·mol−1, and 656.619 kJ·mol−1, respectively.

May 24, 2022

By Nomuqhele N. Nkosi, Yasuo Yabe, Musa D. Manzi, Raymond J. Durrheim, Siyanda B. Mngadi

This study examined rock failure in brittle rocks hosting the deep gold-bearing ore bodies on scales between millimeters and kilometres. This research study is part of the International Continental scientific Drilling Program (ICDP) project, “Drilling into Seismogenic Zones of M2.0-M5.5 earthquakes in deep South African gold mines” (DSeis). The broader ICDP-DSeis project aims include the examination of the extent of damage, the stress state around the fringes of the earthquake, and the potential existence of living organisms associated with deep-level earthquakes. Nevertheless, this study focused on two seismogenic zones – the Cooke 4 mine and Moab Khotsong mine. At Cooke 4 mine, the study examined the evolution of mining-induced fractures (M1-4) occurring ahead of the stope face during the extraction of the remnant shaft pillar. These fractures were monitored and delineated by a dense array of acoustic emission sensors that allowed hypocentres to be located with decimeter accuracy. Using this acoustic emission data, the DSeis team drilled and recovered the fractures, rock breccia and gouge using a sophisticated triple-tube drilling rig.

Apr 26, 2022

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

The Earth?s population is approaching 6.6 billion people. More than half live in urban areas. And, as those figures continue to grow, the need to make wise use of the world?s natural resources as well as its living space will also grow. Thus, the concept of sustainable development ? meeting the needs of the current generation while preserving resources for future generations. The use of underground space is only one part of the sustainable development concept. But it is an important one. Tunnels and underground space are environmentally friendly and contribute significantly to sustainable development. But it takes years to plan and build tunnels and other underground infrastructure. And the demand for infrastructure in the world?s mega cities has grown significantly. In December, about 100 people representing several developed and developing nations spent a day at the United Nations (UN) in New York City discussing the future of underground space development throughout the world. The meeting was put on by the UN?s Department of Economic and Social Affairs and the International Tunnelling and Underground Space Association (ITA). The conference was titled ?The Use of Underground Space as an Unexpected Solution for Promoting Sustainable Development.? Its aim was to promote practical solutions to the use of underground space and tunnels as feasible alternatives to promote sustainable development throughout the world. A panel of speakers from government, academia, the UN and the ITA stressed that development is not sustainable without infrastructure. And, as the world?s population grows, there is now an urgent requirement to efficiently plan for the use of underground space to preserve it for the future benefit of mankind. The benefits of the use of underground space are many, they said. Among them: ? Tunnels channel clean water in and waste water out. This promotes health and sustainability worldwide, particularly in developing countries. ? The use of tunnels and underground space helps conserve energy and increases its efficient use ? the use of tunnels cuts commuting time and so saves energy. ? Tunnels, microtunnels and other underground structures promote the more efficient use of space in large cities ? the bulk storage of water, fuel and other goods. ? Underground structures are subject to less stress than surface structures, making them safe havens for natural and man-made hazards, including earthquakes. And, because underground structures are more durable, lifecycle costs are less than surface structures. ? Underground structures promote the multiple use of available land. Land owner-ship at several layers increases land use and provides more usable space. Han Admiraal is director of the Center for Underground Construction in the Netherlands. He said that urban planners need a new vision concerning the use of underground space. Going underground protects historical and archaeological surface facilities, he said. Underground space use can also protect populations located in adverse climates. And sensitive environmental areas on the surface can also be protected from development. In addition to the transportation of people, freight and water, underground development can also store water, as well as provide storage for waste, hazardous materials, carbon dioxide and geothermal energy. The upshot of this new awareness and vision for under-ground space is that its use should be considered before surface development, Admiraal said. And planners and developers are placing more emphasis on underground space development as part of their overall development plans for urban areas. That was not always the case, he said. In the past, underground space was not considered until after the surface space had run out, he said.

Jan 1, 2008