Search Documents

By K. Boakye, T. Newman, P. Bláha, M. B. Toelle

"This paper presents a quarry optimization plan using a block model and an in-house development quarry scheduling and optimization software (QSO Expert) to help improve quarry operations at Crystal River. The Crystal River Quarry is an underwater quarrying operation that barges limestone via the Gulf of Mexico, as the main source of raw material to a cement plant in Theodore, Alabama. To improve the quarry operation, an evaluation was completed to optimize the quarry planning and extraction procedures of the quarry. In order to achieve this, additional exploration drilling campaign was implemented, a new block model was re-calculated and the latest version of QSO Expert software was used. The primary economic impact is a higher recovery of limestone reserves; sustainability of resources, corresponding longer quarry life. Secondarily as the limestone is mined underwater and stockpiled above water, drainage reduces moisture content achieving direct cost reduction on limestone shipping. In addition, a considerable reduction in operational cost was achieved due to a significant decrease in consumption of electrical energy, reduced dragline maintenance costs and reduced dragline movements within the operation. INTRODUCTION Holcim is a Swiss-based global building materials and aggregates company. Founded in 1912, the company expanded into France and then throughout Europe and Middle East during the 1920s. In 1922, Holderbank, as the company was then known, expanded beyond the Swiss borders into France. By the end of the decade Holderbank held stakes in Belgium, Germany, the Netherlands, and Egypt (Holcim History 1912-2012) Positions in Lebanon and South Africa soon followed.. Holder bank later expanded in North America in the 1950’s. In the late 1970s and early 1980s, Holderbank continued its expansion in Latin America, Asia and Spain for the first time. The company expanded into Eastern Europe and experienced a boom in Spanish construction preceding the 1992 Summer Olympics. By 1986, Holderbank was the world's largest cement manufacturer. In the 1990s, the company consolidated its European holdings as the American market drove growth. Expansion into Eastern Europe and Russia continued (Holcim History 1912-2012). In 2001, the company changed its name from ""Holderbank Financière Glaris"" to Holcim (short for Holderbank ciment) (Holcim History 1912-2012). Holcim expanded by purchasing Aggregate Industries entering into the United Kingdom for the first time. That year, the company also expanded into India by acquiring a stakes in The Associated Cement Companies (ACC) and Ambuja Cement Eastern. In 2008, Holcim became the largest shareholder of China's Huaxin Cement with a 40% stake. In 2009, they acquired Cemex Australia. In 2014, Holcim and Lafarge announced they had agreed to terms on a ""merger of equals"" valued at nearly $50 billion in 2015. The new company LafargeHolcim based in Switzerland has a manufacturing capacity of 427 metric million tons a year."

Jan 1, 2017

By John W. Shield

Oxide gold reserves are being rapidly depleted, especially in regions with long histories of gold mining, such as the Black Hills of South Dakota. However, these districts often have substantial additional deposits, where gold is refractory. It is not amenable to traditional cyanide extraction due to the presence of sulfide minerals that encapsulate or otherwise preclude the economic extraction of the gold. Several technologies have been developed to render refractory sulfide deposits amenable to traditional cyanide processing. These include roasting and pressure autoclaving. Unfortunately, these oxidation processes require substantial capital investment and incur significant operating costs. Microorganisms that obtain energy for their life processes by the oxidation of iron sulfides can be used to treat gold-bearing refractory sulfide minerals. As the bacteria convert the sulfide to sulfate, they expose any gold associated with the sulfide matrix. This makes the gold amenable to cyanide extraction.

Jan 1, 1996

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971

By Joseph Sopko, Xavier Lacourse-Dontigny

For the REM (Réseau Express Métropolitain) project, a 2500 m tunnel was built using a tunnel boring machine (TBM) under the Montreal Pierre Elliott Trudeau Airport (ADM). Although the geology under the Montreal Airport (ADM) would have been suitable for an excavation with a hard rock machine, the rst section reuired an earth pressure balance (EPB) TBM due to the soft soil located under wetlands. After excavating 280 m, the TBM was blocked in a transition zone of unconsolidated, water-bearing soils directly above the underlying bedrock. A free air intervention was not possible due to these geological conditions. After several failed attempts to create a slurry cake for hyperbaric interventions, a ground freezing system was designed and implemented, incorporating angled pipes drilled from outside the wetlands to directly in front of the cutterhead. This paper discusses the engineering reuired to form a frozen, water-tight zone in front of the cutterhead using liuid nitrogen. It also describes the complex method of replacing the disc cutters while holding the ground freezing system active in a manner protecting the health and safety of the workers.

Jun 23, 2024

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

OBJECTIVES OF RADIATION MONITORING Monitoring is a tool used in the practice of radiation protection. The primary reasons for monitoring are to reduce radiation exposures to levels that are as low as reasonably achievable and to assure that no individual receives a dose exceeding the maximum individual dose limit. The documentation of radiation doses for legal, medical, or epidemiological reasons is a subordinate function of any monitoring program. The investment in radiation monitoring programs should be guided by four criteria: (1) the detection and avoidance of unnecessary exposures, (2) the magnitude of potential health risks, (3) the determination of combined doses and risks with adequate confidence, and (4) the verification of compliance with established limits. FIRST CRITERION: DOSE REDUCTION - DETECT AND CORRECT UNNECESSARY EXPOSURES The system of dose limitation advocated by the International Commission on Radiological Protection (ICRP, 1977), and subscribed to in a broad sense by various regulatory agencies, is comprised of three essential ingredients: (1) [justification] of any practice that produces radiation doses by some commensurate net benefit, (2) [optimization] of radiation control measures by reducing doses to levels that are as low as reasonably achievable, and (3) [limitation] of individual doses to preclude inequities and [moldistribution] of risks. All too often, only the third criterion - the limitation of individual doses to prescribed regulatory limits - is explicitly addressed in everyday radiation protection programs. The emphasis of most exposure control and monitoring efforts appears to be directed toward limiting and documenting individual doses that might approach the legal limit. The first two criteria, i.e. justification and optimization, should contribute to a rationale for allocating monitoring efforts. When applied to individuals, these criteria mean the detection and elimination of unnecessary exposures. This should be a high priority of any monitoring program. Measurements should be directed toward detecting inoperative or ineffective control measures, whether or not there is a risk of exceeding the individual dose limits. The ICRP recommends a procedure that can be used effectively to reduce unnecessary exposures. A n investigation level should be established at an exposure rate substantially lower than the regulatory limit, e.g. 30% of the limit (ICRP 26, 1977, p.33). Measurements obtained during routine monitoring that exceed the investigation level are evaluated with respect to cause and potential reduction. To be effective, the evaluation results should be formally recorded and conveyed both to management and to the workers involved. Although the investigation level recommended by the ICRP is based on a fixed exposure rate or derived air concentration, an equally effective evaluation program may be based on the investigation of a percentage of all measurements. For example, one might investigate the highest 5% or a random selection of all measurements. In any case, the objective is to detect and correct situations that are producing unnecessary exposures. SECOND CRITERION: MONITOR IN PROPORTION TO THE MAGNITUDE OF RISK The ICRP criteria apply generally to all radiation exposures. However, a second priority for monitoring programs should be established on the basis of the nature of the exposures and the magnitude of the health risks involved. Current practices in radiation protection are based on dose limits to specific organs and assessment of individual exposure pathways, with little consideration of the combined doses from various pathways. Although the intent of the ICRP recommendations was to limit the total dose to each critical organ, combined doses from external and internal sources are rarely determined. The recent recommendations of the ICRP (Publ. 26, 1977) are based on the limitation of total health risk from occupational radiation exposures. Implementation of this concept would necessarily require the measurement, calculation and summation of doses and concomitant risks to all organs of the body from all exposure pathways. The U.S. Environmental Protection Agency has taken the first step toward translating the ICRP recommendations into regulations. The proposed recommendations for Federal Radiation Protection Guidance for Occupational Exposures (USEPA, 1981) include provisions for summing the risk-weighted organ doses to determine compliance with an effective whole-body dose equivalent limit. Whether or not the proposed guidance is modified before final adoption, it seems clear that some version of dose summation and combined risk limitation will be included in future regulations. With this

Jan 1, 1981

By John C. Harkey

The paper shares programs that presently use the CDC PLATO System to train individuals in industry. A short history of PLATO development; as a training system is presented with reflection on the major training trends being used to improve training effectiveness. A discussion is offered to describe the benefits of using a system for individualizing instruction. An introduction; is offered showing how one can recognize' individual differences, with an explanation of how the strengths of a computer are used to deliver and manage the training. Simulations of hazardous processes are shown to be one of the most effective uses of the computer for training.

Jan 1, 1979

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection'units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer's preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By Ralph C. Kirby

The U.S. produces about 34 percent of the world's aluminum yet must import 90 percent of the raw materials needed. There are abundant resources of aluminum-bearing minerals such as clay, anorthosite, alunite, shale, and dawsonite, but none of the numerous processes proposed for recovering alumina from them has yet proved economically competitive with the Bayer process using imported bauxite. To help develop an economically viable process for utilizing these resources, the Bureau of Mines is testing on a common basis several proudsing processing techniques. New improvements and approaches developed by industry and the Government are being evaluated on a mall scale to obtain enough information on which to form a judgment regarding the best processes for commercial adoption. A continuous miniplant having a feed rate of about 70 pounds per hour is being operated now to investigate the nitric acid process for recovering alumina from clay. Parts of this plant will be used subsequently for work on other processes for recovering alumina from clay, anorthosite, alunite, and dawsonite. Initial results of the operation and plans for the overall project will be discussed.

Jan 1, 1974

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By P. H. Qi

Activated carbon loaded with gold from different halide solutions has been characterized by thermal analysis techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. TGA and DT A measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ration of reduced; adsorbed gold increases for gold halides in the order Au-I > Au-Br > Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, AuI and AuI3.

Jan 1, 1996

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By Scott Lewis, Andrew Kositsky

"INTRODUCTIONThe South Napa Earthquake of 2014 caused ground motion at numerous reinforced concrete-lined (shotcrete-lined) winery tunnels in Napa County and Sonoma County, California. The occurrence of seismic ground motion at these tunnel complexes, known as wine caves, presented an opportunity to reevaluate seismic performance of reinforced concrete and reinforced shotcrete lined tunnels. The authors of this paper updated the most recent comprehensive compilation and evaluation of case studies by Power and others (1998), which correlates peak ground acceleration (PGA) at tunnel sites to damage. For this update, the authors evaluated the seismic performance of 31 wine caves near the South Napa Earthquake epicenter; including some of the 90 wine caves they designed since 1991, some caves designed by others, and additional caves constructed by contractors that they frequently work with. Tunnel designers can use the new data presented in this paper to help evaluate the usefulness of detailed seismic design analyses. THE SOUTH NAPA EARTHQUAKE The South Napa Earthquake occurred at 3:20 AM Pacific Daylight Time on August 24, 2014. Figure 1 shows the approximate location of the epicenter, the measured/estimated PGA contours, and the location of wineries with wine caves added to the database where the PGA was at least 0.2 g. The epicenter was along the West Napa fault, about 5 miles south-southwest of downtown Napa, California. The earthquake moment magnitude was 6.0, and measured/estimated PGAs were up to about 0.7 g. The duration of strong shaking was about 10 seconds. This earthquake was characterized by right lateral strike-slip fault movement, ground surface rupture, and after slip at the ruptures. Increased surface water flows were observed at seven creeks after the earthquake. Groundwater level rises of up to 5 feet were observed in Sonoma County wells after the earthquake. The earthquake was the largest seismic event in the San Francisco Bay Area, which includes Napa and Sonoma Counties, since the 1989 Loma Prieta Earthquake. The Napa event caused an estimated $400 million in damage. This damage included moderate to extensive structural damage to older commercial buildings and to some newer buildings in downtown Napa. This damage resulted from ground motions, subsequent fires, and failed underground utility systems."

Jan 1, 2016

NICOR Mineral Ventures, Inc. retained Neyer, Tiseo and Hindo, Ltd. to evaluate the potential effects of a planned dewatering operation at NICOR's proposed, 258-acre silica sand mining facility near South Rockwood, Michigan. The ?orebody? is a horizontally extensive, friable, quartz sandstone from the Sylvania Formation which also serves as an aquifer for some of the rural, residential development near the site. We conducted an aquifer test on the site which identified the important aquifer properties. Using these data and an analytical model, we determined that the radius of influence would be expected to range up to 6000 feet from the quarry during its final development stage. An inventory of water supply wells revealed that most wells had sufficient available drawdown and would not be adversely affected. A long-term groundwater monitoring program was recommended to monitor the possible effects at some of the closest wells.

Jan 1, 1987

By H Vigil, G. Peach

Long tunnels with only one access shaft pose many program problems for logistics, combine these with the requirement to drive directly out under the seabed for 10.2 km, and the program issues become even more challenging. The Musaimeer outfall tunnel was one such tunnel and to meet and eventually improve on the planned completion date required a complex and extensive management of all tunnel logistics required to support consistent tunneling for a two-year period. This technical paper will discuss the management issues and solutions implemented to meet the challenges of the Outfall tunnel construction.

Dec 1, 2022

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022

By L. R. Gremillion

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commercial deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained 4 to 10 mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. The samples contained varieties of francolites, fluorapatites, and mixed hydroxyl-fluorapatites. The apatite compositions calculated from the chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2 for (PO4)3 and the P2O5 contents of the apatites ranged from 35.1% for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate are, it is necessary to consider the dissolution behavior of the different mineral phases during acidulation and the effects they may have on the chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, the acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1978

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By Jack O?Hearn

A liquid and solid waste management plan for an operating uranium ore processing mill was developed to efficiently and effectively dispose of existing solid wastes and related, affected surface and ground water resources. The goal of this management plan was to achieve satisfactory clean up of these existing wastes ad their by-products as well as to prevent similar situations from occurring in the future. An existing, modern system of synthetically lined tailings ponds, constructed after many years of mill operations, now provides an approved site for the disposal and containment of waste streams currently generated by the mill. This system was thought to be readily adaptable to serve as a key element of the waste management plan. The potential presence of extra capacity in these ponds could eliminate or reduce expenditures for new facilities required solely for proper management of liquid and solid wastes generated by operations prior to construction of the modern tailings ponds as well as for a range of anticipated future operations.

Jan 1, 1984

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994