Search Documents

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

By Jennifer B. Leinart

Sixty percent of the mines responding to the sixth annual Mining Cost Service labor survey reported increases in wages averaging 3.4% over the preceding 12 months. Only one mine reported a decrease in wages and this was accompanied by initiation of a substantial profit-sharing plan. Thirty-nine percent reported no change in wages. Thirty-seven percent reported using some form of incentive bonus plan. Mining Cost Service annually surveys coal, metal, and industrial mineral mines throughout the United States. Information about wages, benefits, and incentive bonus plans is part of an extensive data collection program to monitor cost areas of significance to the mining industry. This year, 131 mines responded to the survey. The data is collected by sending questionnaires to personnel managers at active mining operations. The information included in this article was taken from the returned forms, from labor contracts provided by some of the mines, and from followup telephone calls. This year's data was collected between November 1988 and February 1989.

Jan 1, 1990

By Jan L. Reichelderfer, Thomas L. Richardson

Completion of the H-3 Highway Tunnel Project was a critical element in opening this award winning project. The exploratory tunnel was completed as a maintenance tunnel and included difficult shafts extending into the main tunnel cross passages. The project also involved a major addition to the traffic operations center including a deep excavation in close proximity to the tunnel portal structures. The projects also included various completions and improvements to the main tunnels, such as paving, drainage, maintenance, and a variety of critical life-safety issues, such as radio systems, telephones, etc. The highway opened in December 1997.

Jan 1, 2001

By Paul Lynch

"Since being reported to the 2012 UMI in Shanghai, the Cook Islands has been steadily developing for the commencement of it Seabed Minerals sector in its large Exclusive Economic Zone which contain a vast and unique Manganese Nodule resource, estimated at 10 billion tonnes1. At the 2013 UMI in Brazil, it was reported that the Seabed Minerals Act had commenced and all the necessary complex Technical aspects of this developmental work was being undertaken. At the 2014 UMI in Portugal, full details of the final developments leading to the opening of the Tender of Exploration Blocks in the Cook Islands EEZ will be presented in a brief but comprehensive method, using Poster displays, Powerpoint and active Website interaction. This will show the drafted Regulations, prepared on best international standards, to address both Licencing and Environmental requirements, to give clarity and security to the Resources Owner, industry and stakeholders. This work in being coordinated by the Cook Islands Seabed Minerals Authority, with the valuable collaboration of many international, regional and national stakeholders, including the Cook Islands NGOs, Marine Resources, Marine Park and National Environment Service."

Sep 1, 2014

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

Seven legendary figures of American mining will be enshrined in the National Mining Hall of Fame in ceremonies on Saturday, Sept. 7 at the Little America Hotel in Salt Lake City, UT. The 15th annual induction banquet will begin with a reception at 6 pm, followed at 7 pm by the dinner and the program. Of the seven inductees, one is living. He is Alexander Murray (Bud) Wilson, 80, of Los Altos, CA. Wilson led Utah Construction (later Utah International) to become one of the world’s most diversified and successful mining companies in the 1960s and 1970s. It was acquired by General Electric in 1976.

Jan 1, 2002

By H. Lyn Bourne

This is the seventh annual tabulation of royalty information. It is also the first year in which some data have been deleted to make room for new data. The concept of royalties evolved from a time when the government owned all of the land, including mines, to the situation where free miners won the right to claim minerals but paid a portion of their production to the royal treasury. Today, a mineral royalty is a payment to the owner of the mineral rights for the privilege of producing the mineral commodity. However, some people incorrectly believe that the selling price and the royalty are the same thing. The contract between the owner (lessor) and the mining company (lessee) is the mineral lease. Some clauses that are common to mineral leases include: identification of property, granting clause, reservations, definitions, royalty rate, taxes and title, indemnity, termination, inspection, assignability, successors, and reclamation. There often are variations in royalty rates for a given commodity that reflect differences in location, quality, market conditions or public versus private ownership. History In the time of ancient Rome, the government owned the mining properties by virtue of conquest. It would lease the mines to favored citizens who would pay rent to the State. Various conditions of sovereign ownership of both land and mineral rights continued in Europe until the Renaissance. As the laws evolved for land ownership by private citizens, the concept that minerals belonged to the State (King, Crown, sovereign) continued until about the 15th century. Free miners challenged the notion of sovereign ownership and won the right to discover and claim minerals. But a portion of their production had to be paid to the sovereign - a royalty. So, the original concept of a mineral royalty was a tax on production that was due to the Crown or Church. The term mineral royalty, as it is known today, is a payment to the owner of the mineral rights (formerly the royal owner) for the privilege of mining and producing the mineral commodity. The owner of the mineral rights, the lessor, and the mine operator, the lessee, enter into an agreement to mine the property. The agreement is the lease. While this concept is common, there are some who do not understand that the royalty is a portion of production paid to the owner as agreed on in the lease document. This author has seen reports where the selling price of a commodity has been quoted as the royalty. ("They get 70 cents a ton royalty at their pit and the guy down the road only has a 65 cent royalty.") These reports have been authored by people not familiar with the mining industry. Lease clauses In addition to the amount to be paid the lessor, there are several other items to be addressed in the lease agreement. The following list may not be all inclusive, but briefly describes most of the common clauses any good mining lease should contain. Identification: This opening clause names the owner (lessor) and the operator (lessee), the address of each, and gives the legal description of the property. Granting clause: This part of the lease gives the time period or duration of the agreement and information about renewal periods. It also has language about the exclusive right of the lessee to mine the property. Reservations: If the owner wants to exclude any portion of the property or set some specific conditions about the operation, there needs to be a clause that describes these reservations. Definitions: This section should address some of the technical terms that the lessor may find confusing - short tons versus cubic yards, dollars versus percentage of average selling price, any escalator indices such as consumer price index or producer price index, and material mined versus material sold. Royalty: This section spells out what the royalty rate will be, how often it will be paid, if there is an annual minimum, the pay dates, and how the records will be kept. This section also describes the conditions under which the lessee is exempt from the annual minimum - natural disasters, strikes, governmental actions, or other causes referred to as force majeure. Taxes and title: The lease needs to identify who is responsible for the property taxes, severance taxes (if applicable), and other taxes that relate to the mining activity - taxes on equipment, improvements, or stockpiles. This is a good place in the lease for the owner to certify his ownership of the property and its mineral rights and also certify that no other leases are in effect. The lessees may want language that allows them to pay mortgages or other debts on the property to keep their lease in effect. Indemnity: This portion of the lease identifies that the lessee assumes the risks for lessee's mining operation. Lessor should expect indemnification by the lessee through standard insur¬ance policies - workers compensation, liability and property damage. Termination: Both the lessor and lessee want language that will allow them to terminate the lease. This section of the lease describes the conditions under which one of the parties may terminate the lease (failure of the

Jan 1, 1989

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

By David Shatwell

Recent epithermal gold discoveries in Chile and Bolivia provide increasing evidence of a belt of intermittent, epithermal, precious metal mineralization east of the main Andean porphyry copper belt. This relationship may be the result of an easterly decrease in the age of magmatism and erosional levels, in¬crease in depth above the underlying Benioff zone and consequent changes in magma chemistry, or some other unrecognized factor. Examples are: • The Choquelimpie gold-silver mine in Chile and numerous other epithermal prospects (such as La Riviera, Bolivia) in late Tertiary volcanics along the Chile-Bolivia border. These lie east of the belt that contains the Toquepala, Quellaveco and Cuajone porphyries in southern Peru and the Cerro Colorado, Copaquire and Quebrada Blanca porphyries in northern rhila

Jan 1, 1990

By M. J. Price

The usage of Geographic Information Systems (GIS) is increasing rapidly throughout the Mining Industry, especially in the Industrial Minerals sector. GIS provides an efficient and robust link between spatial (often CADD) and tabular (database/spreadsheet) components. Mineral economists and corporate planners employ GIS to perform market analyses, to source raw materials, and to schedule and monitor deliveries to customers. Exploration and acquisition groups apply spatial analysis to identify high quality resources that meet economic guidelines. Mining regulators and environmental affairs departments expedite and monitor permitting, environmental compliance, and best management practices reclamation through GIS data management and Electronic Permitting. Operations staffs monitor overburden removal, material extraction, quality control, and stockpile volumes with GIS. This paper summarizes the many aspects of GIS in Industrial Minerals. It also introduces and addresses issues and concerns commonly encountered during a mining GIS implementation.

Jan 1, 2001

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By M. E. Kravetz, E. B. Milosavljevic, L. R. Solujic

Gold ores containing high levels of cyanide-leachable copper minerals, such as covellite, chalcocite, bornite, malachite, azurite, and cuprite have traditionally been difficult to treat economically. A novel hydrometallurgical process for efficient treatment of cyanidation effluents obtained by leaching high copper gold ores (or concentrates) based on the use of Cherokee Chemical organo-sulfur reagents (OSR-A, OSR-B and OSR-C) is described. The process may be modified to selectively precipitate silver, or completely recover silver, copper and zinc, as well as regenerate significant amounts of cyanide. For example, data obtained demonstrate that 100 % of silver and zinc, and 98 % of copper were removed from the solution, while 80 % of cyanide was recovered. The treated barren solutions exhibit enhanced gold and silver leaching kinetics compared to the untreated controls.

Jan 1, 2004

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

By Ma. X.

Passive seismic imaging is applied in underground mining to analyze the stress redistribution after the occurrence of a major seismic event. The velocity model is established to be utilized in velocity inversion. By comparing the images from velocity tomography on two different time scales, the average velocity of a mining area decreases significantly after the major event. It is highly likely that the stored energy level drops due to the occurrence of a major event. Also, total energy stored in micro-seismic events for each day is summed up and the energy change trend is plotted to illustrate the correlation of energy with a major event.

Feb 27, 2013

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003

By K. Park, J. Sohn

Recovery of industrially useful metals from various secondary sources is an important issue in Korea whose natural resources are limited and needs in the strategic metals are on the rise. In order to meet such needs, researchers at the Korea Institute of Geoscience and Mineral Resources have launched a number of projects to help the nation to recover various metals from secondary sources. In this study, silver is successfully recovered from spent silver-oxide batteries first by distillation to remove mercury. The distilled residue was next subjected to leaching of silver using nitric acid. The study involves finding optimum conditions to leach silver from the distilled residue and subsequently to recover silver from the leach liquor by chemical precipitation. The chemically precipitated products are then subjected to reduction roasting to recover silver metal.

Jan 1, 2002