Search Documents

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By B. K. Parekh, Z. Chen

INTRODUCTION The need for cleaning and recovery of fine (minus 28 mesh or 0.5 mm) coal fraction has increased in recent years. This results from realizing a substantial recovery of ultraclean coal from the waste stream improving overall Btu (heat) recovery, providing extra revenue for the coal industry. Also the potential of using the clean coal so obtained for making coal-water mixture which could replace oil. An additional benefit of recovery clean coal from the waste stream is reducing environmental concern of burning uncleaned coal and in waste disposal. Deashing of coal by physical beneficiation processes is limited by the degree to which ash components are liberated from coal. Conventional processes have been inefficient in terms of Btu recovery, for ultrafine coal. Chemical cleaning methods, which involves leaching of ash material from coal, have provided ultraclean coal at high Btu recoveries, are more costly than the physical cleaning methods. An advanced physical separation technique that appears to address the need discussed above is selective flocculation. This technique which has been successfully utilized in iron ore beneficiation offers the potential of processing fine and ultrafine coal to produce a clean fuel. OBJECTIVES The main objective of the present study is to investigate applicability of selective flocculation technique for recovery of clean coal product from the waste coal slurry supplied by the Peabody Coal co., from their three different coal preparation plants. It is also the objective of the program to conduct preliminary economic study of the selective flocculation process.

Jan 1, 2002

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don&apos;t always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By Michael Feroz

Severe drought in the Colorado River Basin over the past 10 years has caused water levels to drop in Lake Mead by more than 113 feet. The current lake level is at elevation 1,112 feet mean sea level (msl). Lake Mead is the primary source of water supply for greater Las Vegas. Water for Las Vegas from Lake Mead is accessed through two existing submerged intake shaft and tunnel systems. If the water levels continue to drop in the lake, the Intake No. 1 will become inoperable below water level elevation of 1,050 feet msl. To sustain the current levels of water delivery to all member agen-cies in the southern Nevada region, the Southern Nevada Water Authority (SNWA) has decided to construct a third intake at a deeper depth in the lake to ensure better quality water and enhanced reliability.

By E. M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger miners have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1987

By E. Tulcanaza

M.S. Azun I do not at all agree with the basic points of the author&apos;s conclusion. The use of lognormal or normal model to respond to the attribute distribution function should be carefully questioned. If fitting a distribution function of regionalized variables is the main purpose, one may employ one of certain well-known families of distributions, such as Tukey&apos;s lambda functions. For instance, the distribution function of gold assay values studied by Krige (Krige, 1978) may fit the lognormal model well, but one should not exclude that the basic idea of using the distribution function of observed data is to have insight of the physical mechanism that gives rise to the regionalized variables. In Applied Geostatistics, there are many examples considering only lognormal or normal model for the distribution function of geostatistical data even if the observed distribution function has more than one mode. Of course, using lognormal or normal model always brings easy computation for the statistical properties of attribute under investigation. Still, I object to adopting any of those models without having any "statistical inference." As seen from the author&apos;s paper, lognormal and normal model produce the same average grade (0.746% copper) and almost the same sample variance. Therefore, which model explains the probabilistic behavior of ore deposit is always an important question that should be replied by the geostatistician using not the common sense but the statistical and probabilistic methods. For kriging procedures, such as linear kriging, one should describe either second order stationary properties or bivariate properties of regionalized variables. Second order properties, such as correlogram function or semivariogram function, are the inputs of the so-called kriging equations. Selecting one of any useable models for the observed second order properties, such as spherical model, is not easy since the models are not based on the correlations structure of the regionalized variables. How those models being used in Applied Geostatistics can be distinguished is another important problem. One may develop many fitting models to respond to the observed second order properties of regionalized variables. However, I suggest that the model should be based on the probabilistic behavior of geologic process. The author used spherical model for copper, wolfram, and silver grades from isotropic sector (Fig. 2, 4, 3b) and exponential model for silver grades obtained along raises in isotropic sector (Fig. 3a). It seems that those semivariograms given in Fig. 3b for isotropic sector and Fig. 4 may be described by the random model implying that regionalized variables do belong to renewal process (Azun, 1983). If I knew the total number of data points used in estimation, I may prove that my conclusion is correct. Recalling the test for the first order sample correlogram value, the test procedure is introduced such that the independence is rejected if [ ] where Za/2 is the a/2 percentile of standard normal random variable and N is the total number of samples used in estimation (Azun, 1983). For the other observed semivariogram functions I suggest the author might try to use the so-called "Markovian model" describing not only the correlation structure of regionalized variables, but also the physical mechanism that produces the regionalized variables. The Markovian model for correlogram function is, [ ] The Markovian model for the other second order properties of ReV are also derived. T ve B, in the above equation, show, for example, structural change and mineralizational variation in a considered deposit, respectively (Azun, 1983). In selecting any model, it is not easy to search for the "best" response to the observed second order properties of ReV&apos;s. The Markovian model, based on a theoretical understanding of underlying mechanism, gives more information about the occurrence of regionalized variables and respond to all properties. Random model and the so-called hole effect structure can be easily defined as a special form of the Markovian model (Azun, 1983). An estimation of any second order properties of regionalized variables may be computed through (N-1) lag. However, the dependency between the regionalized variables may be deemed to have "died out" after the so-called stationarity width (range). In practice, the estimation is carried out through 25% of the total number samples available. Therefore, the large fluctuations around the zero level and variance for correlogram or covariogram function and semi-variogram function, respectively, cannot be observed. Since the number of pairs involved in the estimation of higher second order properties is small, the estimation variance at those lags is large. There is no need to show higher order estimated second order properties. After using one of any kriging procedure for block estimation, the distribution function of average grades has the same mean as the drilling sample grades but

Jan 3, 1985

By F. F. Roberto

Many techniques that are used to characterize and monitor microbial populations associated with sulfide mineral bioleaching require the cultivation of the organisms on solid or liquid media. Chemolithotrophic species, such as Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans, or thermophilic chemolithotrophs, such as Acidianus brierleyi and Sulfolobus solfataricus can grow quite slowly, requiring weeks to complete efforts to identify and quantify these microbes associated with bioleach samples. Real-time PCR (polymerase chain reaction) assays in which DNA targets are amplified in the presence of fluorescent oligonucleotide primers, allowing the monitoring and quantification of the amplification reactions as they progress, provide a means of rapidly detecting the presence of microbial species of interest, and their relative abundance in a sample. This presentation will describe the design and use of such assays to monitor acidophilic microbes in the environment and in bioleaching operations. These assays provide results within 2-3 hours, and can detect less than 100 individual microbial cells.

Jan 1, 2009

By K. A. Larsen, J. L. Ariail, C. M. LaRosa

This article discusses the evolution of U.S. laws and policies towards environmental remediation at mine lands over the last 20years, the opportunities that these changes present for reuse, and the remaining challenges associated with community capacity for effective reuse planning and implementation. Emerging initiatives by the U.S. Environmental Protection Agency and Department of Interior for addressing these challenges are discussed.

Jan 1, 2004

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

By E. A. Metz

Perfect combustion in an engine would produce only water vapor, carbon dioxide and nitrogen as by-products; however, complete combustion is never achieved. As a mobile power plant, the diesel engine is relatively inefficient in terms of energy produced from the energy potential of the fuel. The diesel is not a perfect engine. The fuel burned can undergo a very large number of reactions in the combustion chamber. It only stands to reason that a large number of compounds are contained in the exhaust, actually, thousands of chemicals. The exhaust can be broadly divided into a gaseous phase and a particulate phase. Each phase is made up of organic and inorganic compounds. The vapor phase contains carbon monoxide, sulfur dioxide, various oxides of nitrogen and many hydrocarbons. The particulate phase contains clusters of respirable inorganic particles made mostly of carbon. This paper will address the health hazards, as we know them today, of the major components of the particulate phase in the exhaust of diesel engines. It will briefly examine the operational factors of the diesel engine as it applies to particulate emissions. Longitudinal studies of occupationally exposed miners are needed with documentation of levels of exposure before a chronic effect of exposure can be determined. At this time, it is not possible to conclude from human studies the level of diesel exhaust exposure that results in the observed lung cancer risk.

Jan 1, 2001

By Tony Szwilski

Indonesia has enormous mineral resources. Its population of more than 180 million people inhabit most of the more than 13,000 islands. The country is becoming a significant economic power in Southeast Asia. Indonesia is the largest Muslim country in the world. Java, its largest island, is the most densely populated area. The country&apos;s diversity is its strength. However, as only an estimated 16 million inhabitants speak bahasa Indonesia as the first language, communication problems endure. Although burdened with large debts, Indonesia has been able to service the debts better than most developing nations. This has given it high credibility and, with increasing frequency, creditor nations compete to provide Indonesia loans with the most the most favorable financial terms. Recent rising prices of petroleum crude has further improved Indonesia&apos;s economic status. It maintains a policy of stable oil prices that it promotes in OPEC, of which it is an influential member. As a result, Indonesia is becoming increasingly attractive to foreign investors. The South East Consortium for International Development (SECID) is made up of 34 universities in the southeastern US and Indonesian partners Lembaga Afiliasi Penelitian dan Industri (LAPI) of the Institute of Technology in Bandung, West Java. SECID bid successfully against international competition to develop new academic programs and campus for the Sriwijaya University UNSRI) in Palembang, South Sumara. Funding for the project was provided by the government of Indonesia through a loan from the Asian Development Bank (ADB). There are 47 public universities

Jan 1, 1991

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

By M. Arias

"An attractive foreign investment legislation, an anti-mining framework in the jurisdiction where a head office is located, the geographical location of the mineral resources, a country that offers the technology needed by the industry for its operations -- these are some of the many factors that make mining and mineral exploration a global business. It is precisely in the complexity of this new era of globalization and market environment, that sustainability initiatives are challenged. Responsible management of mineral exploration and mining is no longer defined by the use of efficient technology and resource management. Sustainability is not only a report compliance exercise or a green revolution. Sustainability is like any business, a long term profitable proposition. This new approach encompasses four pillars: social, economic, environment, and culture. This new approach connects humans and corporations; it is the way to engage, respect and improve relations with the people with whom we work and our neighbours."

Jan 1, 2011

By Drummond Earley III

The hydrology of in situ leach mining operations is being studied by the U.S. Bureau of Mines using a variety of techniques, and the Bureau has made significant advances in tracking and modeling the flow of leach solutions in rock formations. However, the influence that leach solution composition has on the hydrology of these systems is poorly understood, and geochemically-controlled changes in the hydrologic characteristic of ore deposits during in situ leach mining of porphyry-hosted, copper oxide ores have not been previously studied. The Cyprus Casa Grande in situ leach mining operation mines fracture-hosted and disseminated copper oxides (predominantly chrysocolla) hosted by granodiorite porphyry using a pattern of underground wells. The injection solution consists of sulfuric acid raffinate from a solvent extraction-electrowinning plant. Chemical analysis of representative injection and recovery solutions reveals that gangue cation concentrations in these solutions are high, and geochemical modeling shows that the solutions are saturated or nearly saturated with respect to gypsum, jarosite, and various amorphous oxides. Precipitation of these solids is evoked by calcium-exchange reactions, rising pH, and perhaps locally rising redox potential, as the leach solution reacts with the ore minerals, host rocks, and the atmosphere. Mass and volume balance calculations show that approximately 25 cm of precipitates are formed per gram of copper recovered at Cyprus Casa Grande. The results of geochemical modeling agree with petrologic examination of pre-and post-leach core samples from the leached horizon. Moreover, hydrochemical modeling and hydrologic field data suggests that chemical precipitation causes significant decreases in porosity and permeability during in situ leach mining of porphyry-hosted, copper oxide ore.

Jan 1, 1992