Search Documents

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

By Leland E. Paulson

The Grand Forks Energy Research Center and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons each of subbituminous coal and lignite were dried in a commercial scale dryer, oil sprayed and cooled, then shipped in open-top rail cars from Pekin, IL to Grand Forks, ND and stockpiled. Cars containing raw coal and dried coal that had not been oil sprayed were also transported for comparative purposes. The tests were conducted in August and November of 1974. The subbituminous coal was dried from 26 to 16 pct moisture and the heating value was upgraded from 8,420 to 9,650 Btu/lb. The lignite was dried from 39 to 22 pct moisture and its heating value was increased from 6,420 to 8,300 Btu/lb. Before loading subbituminous coal was cooled to 115° F and sprayed with oil at a rate of from 2 to 6 gal/ton. Similarly, lignite was cooled to 85° F and oil sprayed at rates of from 1 to 2 gal/ton. Both shipments arrived in Grand Forks with a minimum of difficulty. The subbituminous coal was subjected to 2 inches of rain during transit with no change in average moisture content. The cars containing dried and oil treated coal had less material lost to wind than either cars containing raw or untreated dried coal. With both dried lignite and subbitnminous shipments, a moderate increase in temperature was measured during transit. With the subbituminous shipments, ignition occurred near poorly fitted bottom dump doors, but was limited to a very small area. The dried lignite was shipped when ambient temperatures were below freezing, and frozen coal was noted around the edge of the car. At Grand Forks, the coal was stockpiled using proven techniques and has remained stable to this date.

Jan 1, 1975

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By William Gleason

"Technology of all forms has experienced exponential growth in recent years, and there is no sign of it slowing down. This growth has presented amazing opportunity and significant challenges in nearly every aspect of daily life. Some of these changes are seen and experienced every day as we turn to our smart phones, tablets and smart watches to help with us with everything from directions to the store to managing our health. And other technological growth takes place far away from the public view but can have as much of an impact on our daily life as does shopping at Amazon or connecting with friends on social media.At the “THRIVE 2018, Innovations Advancing Mining” conference presented by SME on Sept. 27 at the Sheraton Pittsburgh Hotel at Station Square in Pittsburgh, PA, the focus was on innovation and how it affects the global mining industry.More than 100 people were on hand for the inaugural event, and they were treated to a unique program that focused on the cutting-edge innovations that will carry the mining industry into the future while increasing safety and productivity along the way.2018 SME President Barbara Arnold was the driving force behind the conference and put together the technical program with a focus on innovation through the entire mining life cycle and into the future. Talks ranged from more efficient and safer ways to extract minerals to some of the most advanced end uses of minerals and metals, including the use of 3D printing to create precision parts for machines and humans from advanced metal alloys.“We need to adapt new technologies to our industry and develop additional technologies as we provide materials and metals for infrastructure and energy development in the United States, around the globe, and to the Moon and beyond,” Arnold told Mining Engineering. “Our inaugural THRIVE conference sets the stage for these innovations to be applied and to continue to be developed. Our mining industry can only continue to thrive with these advances.”"

Jan 11, 2018

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure and other types of sensors are increasingly used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in the new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP), while older forms of serial communication are being retired. This paper presents the selection, configuration and testing methodologies employed by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide IP data transport.IntroductionTo enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry (Zhou et al., 2017). However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology infrastructure in place to handle the data transport requirements for the newer Internet Protocol (IP)-based technologies that are part of IIoT.This was the case with a mine in the Western United States. It lacked the infrastructure to perform critical monitoring in remote headings. Therefore, the mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for the real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder communications system to achieve IP data transport using commercially available land mobile data radios (NIOSH, 2013; Forooshani et al., 2013; Novak, Snyder and Kohler, 2010; Yarkan et al., 2009). The solution, fully evaluated in laboratory and mine environments, requires no modifications to the existing system, is economical, simple to implement, and reliable. It also allows for transition to higher-bandwidth IT networks, such as fiber optic or WiFi, should they become available."

Dec 1, 2018

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006

By Scott Ellenbecker

Soon New York City will have a new train station. A tunnel project is under construction to extend Line 7 to a new station that is located near the Jacob K. Javits Con-vention Center. This is also part of the Hudson Yards redevelopment project that is intended to aid redevelop-ment of the west side of Midtown Manhattan around the Long Island Railroad?s Caemmerer Railyard. The station, or ?cavern? as it?s called by those excavating it, will be the portal for that growth. In the city, public transportation means high-rise residential proper-ties will have better access to the business district, and those outside the area will have greater access to event facilities ? two factors that are critical for development investment.

Jan 3, 2010

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007

By M. Valdebenito, J. Rajala

An OCS Expert control system was implemented by Svedala Cisa at the Minera Maricunga Refugio Crush-Leach Operation near Copiapo, Chile. The purpose of the Expert system was to maximize production through the primary and secondary crushing circuits and help balance crusher usage between each stage to maximize total plant production. Interesting aspects of the control strategies are discussed. Benefits of the control were verified through a randomized On/Off test program. Tonnage increases ranged from 5% to approximately 20% at good confidence intervals. Benefits analysis results are discussed. The crushing plant at Refugio is very remote and is located at approximately 15,500 ft. This poses many challenges. The effect of altitude and remote location on plant operation are discussed.

Jan 1, 2002

By M. J. Miller, N. Ripepi, M. Karmis, J. M. Conrad

Unmineable coal seams present an opportunity to sequester carbon dioxide emissions from power plants, while enhancing the recovery of coalbed methane. Injected carbon dioxide is adsorbed and stored on the coal surface while releasing methane that can be commercially recovered. Carbon sequestration, therefore, allows the utilization of unexploited mineral resources while reducing “greenhouse” gas emissions. This paper presents the feasibility, efficiency and enhanced recovery potential of coalbed methane production using carbon dioxide sequestration in the Central Appalachian Basin. The focus of research is on geological characterization of unmineable coal seams in Central Appalachia and the corresponding carbon dioxide storage capacity. Virginia Tech and Marshall Miller & Associates, Inc. conducted this research under the Department of Energy’s Southeast Regional Carbon Sequestration Partnership program.

Jan 1, 2006

By W. Pawlos, A. Bakalarz, M. Duchnowska

This paper presents the results of an investigation into the influence of hydrodynamics on a preflotation process for the copper sulfide ore from the Fore-Sudetic Monocline deposits in Poland in a flotation machine. The main aim of the preflotation stage for Polish copper ore is to remove the easy-to-float organic matter — organic carbon — that causes serious problems in metallurgical processes. The organic matter is connected with the presence of shale ore. This paper describes the preflotation experiments conducted to investigate the effect of various stirrer speeds. The upgrading selectivity of copper and organic carbon were analyzed and compared. The results show that the effectiveness of separation between organic carbon and copper decreases with increased stirrer speed in the laboratory flotation machine. The more intensive the mixing of the flotation suspension, the lower the selectivity of the preflotation experiment. Lower stirrer speed probably provides lower mechanical entrainment and flotation of copper minerals.

By M. Irish, M. Jahraus

Accurate prediction of gold (or other metal) production from a heap leach operation is essential to the economic vitality of any such operation. However, this is also one of the most challenging issues facing managers of these facilities. Three approaches to modeling gold production from the Valley Leach Facility (VLF) at Anglogold’s Cripple Creek & Victor Gold Mining Company are presented. Evolution of these modeling methods has been necessary as ore heights and volumes have increased. In addition, the complex geometry of the VLF presents additional complications to production modeling, Comparison of actual and predicted gold production are presented

Jan 1, 2001

By J. MacFadyen

The U.S. cement industry, including Puerto Rico, again set a record in terms of production and shipments. The increase in shipments came primarily from imports of portland cement as domestic production from produced and imported clinker gained only 1.9 Mt (2.1 million st). Clinker production as reported to the U.S. Geological Survey (USGS) was 88.6 Mt (97.6 million st), an increase of 1 percent. Gray and white portland cement production from domestic and imported clinker, estimated at 93.5 Mt (103 million st), was up 1.9 Mt (2.1 million st). Masonry cement shipments of 5.5 Mt (6 million st), which equates closely to production, was up 6.3 percent. Blended ce-ment shipments were up 35.9 percent from 2004 at 2.35 Mt (2.6 million st).

Jan 1, 2006

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 150 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey (USGS) canvass of producers. Domestic production in 2005 was estimated to be 24.8 Mt (27.3 million st) valued at $176 million. This was based on a preliminary survey of the common clay and shale industry. The leading producer states, in decreasing order by tonnage, were North Carolina, Texas, Alabama, Georgia and Ohio.

Jan 1, 2006

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

Jan 1, 2001

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

By D. A. Norrgran, J. A. Wernham, D. E. Walsh

A qualitative test program was sponsored jointly by the University of Alaska and Eriez Magnetics, in order to study placer gold nugget recovery using an eddy-current separator. Various gold nuggets from Alaska, ranging from 6.4 mm to 63.5 mm in size, were tested. All testing was performed using an Eriez Laboratory ESC, Model REA, fitted with 2000 gauss, surface field strength magnetic rotor. The belt speed was set to 91 meters per minute and the rotor speed was set to 2500 rpm in the forward direction. The splitter was adjusted to just reject the largest pieces of rock that measured an average 76 mm x102 mm x 127 mm. Based on the results of this limited test work, it can be recommended to placer gold mine operators, that Eriez Magnetics ECS technology is a viable and practical concentration technology for coarse gold recovery. Silver and platinum were also tested.

Jan 1, 2003

By L. Clark

Despite near-record commodity prices, the mining industry continues to search for ways to maintain profits in these times of steadily increasing energy prices and steadily decreasing grades. The pressure is still on today’s miners to continuously improve their operations because they know that one day prices too will drop. Some, however, have seized the opportunity to employ systematic methods to reduce costs and increase the efficiency of their workforce and equipment. As a result, closer attention is being paid to scheduling and the value that could be added by defining the extraction sequence that maximizes the net present value [NPV] of a project. This paper will discuss the challenges faced by Newmont Mining Corporation [Newmont] at its operations and the application of sophisticated software tools and methods in its search of solutions to this problem.

Jan 1, 2007