Search Documents

By R. L. Howell, L. C. Atkinson

Typical sedimentary sequences overlying coal seams consist of interbedded sandstones, siltstones, shales, and rider coal seams. In many surface coalmine settings, these sediments are saturated; and prior dewatering of them is necessary for effective and economic mining, including the stacking of saturated spoils. Such sedimentary sections usually have a very low vertical hydraulic conductivity that does not allow them to drain in a timely manner prior to their being stripped. One potential solution is installation of drainwells. Drainwells are small diameter wells that can collect water laterally from the various more permeable layers in the overburden and then gravity drain it to a lower layer – often the coal seam being mined – where it can be removed by pumping wells or sumps located in the bottom of the pit. A ground-water flow model utilizing the 3-dimensional finite element code MINEDW has been used to evaluate the effectiveness of usingdrainwells in a hydrogeologic setting that is typical of the Powder River Basin. A series of numerical simulations were completed using various combinations and spacings of drainwells and pumping wells to dewater the overburden and coal seams. The numerical simulations suggest that drainwells can be a very effective method of overburden dewatering.

Jan 1, 2000

By B. Arvidson

Computer-controlled machine sorting may, if properly applied, have a dramatic effect on overall economics of a mine operation. Radiometric and photometric sorters have been used for many years and new developments will be reported, such as a sorter for fine particles and a conductivity/magnetic sorter. Application examples with emphasis on precious metals will be given. Economics for some of the projects will be reviewed and discussed. Sorting underground is shown to be particularly attractive, but machine sorting would be profitable in most cases based on savings in transportation and milling/beneficiation costs only.

Jan 1, 1987

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

More than 100,000 people are expected to be in Las Vegas, NV in March for ConExpo-Con/Agg 2002, the largest exhibit of its kind in the Western Hemisphere. This triennial event features equipment, services and technical sessions geared toward the global construction aggregates and ready mix concrete industries. ConExpo-Con/Agg 2002 will take place March 19-25, 2002 at the Las Vegas Convention Center. For registration information, contact the show offices, phone 800-867-6060, 414-298-4141, or 301-587-3140, Website www.conexpoconagg.com.

Jan 1, 2002

By J. C. Potvin

Although the occurrence of deposits of titanium minerals on Kenya’s present day beaches and adjacent dune systems has been well documented, the potential for older formations to host economically viable deposits had not been recognised until recently. The Magarini sands formation in Kenya has been found to contain deposits of ilmenite, rutile and zircon in quantities and grades that have the potential to be commercially exploited. Since 1995, Tiomin Resources Inc. has explored these deposits and has identified one deposit, the Kwale project, as being able to support the development of a mine producing some 300,000 tpa ilmenite, 75,000 tpa rutile and 37,000 tpa zircon. Tiomin plans to start production by late 2002. Construction of a US$137 million operation is set to commence in the first half of 2001.

Jan 1, 2001

By Howard J. Haselhuhn

"The effectiveness of reagent adsorption onto hematite ore particle surfaces is critical during beneficiation to promote effective selective flocculation and dispersion and increase iron oxide recovery. The relationship between aqueous calcium in the process water and the effectiveness of common iron ore dispersants has never before been studied. The nature of common dispersants was studied in the presence and absence of calcium in the process water. The settling behavior of hematite-rich iron ore at pH 11 was assessed in the presence of calcium and inorganic dispersants: sodium silicate, sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP) and organic dispersant ethylenediamenetetraacetic acid (EDTA). It was found that inorganic dispersants are ineffective at a pH of 11 without activating the surface sites of the ore particles with calcium. Organic dispersants, however, were found to be effective with and without surface site activation.IntroductionThe United States produced 54 million metric tons of concentrated iron ore in 2011 (Jorgenson, 2013). Over 8 Mt were produced using a process known as selective flocculation and dispersion (CCI, 2011). The grade of this ore is slowly depleting, making it imperative that processing efficiency improves. To increase processing efficiency, a complete understanding of the effects of chemical reagents in the process must be acquired. This process relies heavily on dispersants to disperse iron oxides from gangue minerals in settling processes. The mechanism that these dispersants use to disperse the ore and its relationship to calcium in the process water has never been studied. The following extended abstract summarizes the relationship between aqueous calcium in process water and the effectiveness of common iron ore dispersants at dispersing hydrated hematite ore. These tests were carried out at a pH of 11, as this is a typical pH used to ensure dispersion in selective flocculation and dispersion processes."

Jan 1, 2015

By Steve Meador

West Virginia's basic coal mining regulatory programs are not unique when compared to Federally approved programs implemented by other coal producing states. In fact, the language in The West Virginia Energy Act governing subsidence mirrors that written in the Federal Surface Mining Control and Reclamation Act as well as other states' statutes. Certain legal and administrative issues, how¬ever, combine to make West Virginia's regulation of surface subsidence a singular approach.

Jan 1, 1986

S.L. Barua and Y.C. Kim M. Armstrong's paper is very interesting and can be regarded as a pioneering work of applying geostatistics on washed coal. The density levels used in her study are uniformly spaced, which facilitated curve fitting through a proper experimental design. Most of the existing coal washing plants in the US, however, gather washability data at non-uniform intervals which, in turn, affects the goodness of curve fitting. We would like to emphasize the importance of having a proper experimental design, if a similar geostatistical application is to be conducted on washed coal. We, at the University of Arizona, tried the variogram on recovery (Kim, Barua, and Baafi, 1982, SME preprint 82-143) which showed a similar pattern as Fig. 4 of Armstrong's paper. In both cases, the first experimental variogram value is invariably and inexplicably higher than the second variogram value. Although Armstrong ignores the first point because of "small number of sample points," we did not do so because there were 17 sample pairs. As a consequence, we concluded that the obtained experimental variogram was unsatisfactory and that further research is warranted. In other words, this disagreement in variogram interpretation between M. Armstrong and the University of Arizona begs the question whether the experimental variogram of Fig. 4 truly reflects the spatial correlation in washed coal, assuming there is such a correlation. Finally, we wish that Armstrong could have done a similar study on clean sulfur, which is a vital interest to the coal mines in the US. Her implied remark on sulfur in the concluding section of the paper may turn out to be incorrect because our experimental variograms on clean sulfur at different density levels were even less satisfactory than those on recovery.

Jan 1, 1985

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By Helmut Hass, Michael B. Gilbert

The extension of the commuter railway system (S-Bahn) in Leipzig, Germany willrequire the construction of an underground line crossing the downtown area of thecity to tie the Bavarian Station in the South to the Main-Station in the North. The City-Tunnel-Leipzig is currently one of the largest infrastructure projects in Europe. This system extension will have a length of approximately five kilometers. 3.9 kilometers of that length are currently being constructed using either cut & cover construction or tunnelingmethods. The design and construction of this project currently is and will continue facing very significant challenging urban and demanding geotechnical conditions.

Jan 1, 2007

By James A. Madonna

Information gathered while studying geological parameters that govern fine gold deposition in the a1luvial environment can be applied to the technological development and selection of fine gold recovery systems. It is recognized that substantial gold losses occur in the minus 1.5 mn (minus 12 mesh) fraction using conventional sluicing systems. Within the past two decades much attention has been given the design and efficiency of these thick bed concentrators. Studies and comparisons drew information from several foreign and domestic placer operations. These studies concentrated on: 1) the physical and chemical properties of alluvial gold 2) the parameters that control fine gold deposition 3) the geometrical form, components and general working structure of conventional sluicing systems 4) the physical properties which contribute to the overall efficiency of a sluice system 5) the comparison of three major styles of conventional sluicing systems. A dramatic improvement regarding fine gold recovery and water quality was observed when using modern multiple-channel sluicing systems in place of conventional single-channel sluicing systems.

Jan 1, 1988

By Derek. C. Arnold

In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir. In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir.

Jan 1, 1999

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By Janine Acasi, Robert D. Rogers, Jonathan K. Trautman, Richard C. Cronn, James H. Wolfram

The demand for phosphate will continue into the future, because phosphate is currently irreplaceable as a plant nutrient and in many chemical applications. Phosphate is not recycled, so the supply must be replenished through a process of mining and purification. The most energy intensive part of the process, separation of phosphate from the ore, requires 54 to 78% (depending on the method used) of the estimated 0.5 quads of energy consumed by the U.S. phosphate industry. This paper provides data from a project designed to determine if a biotechnology can be developed to separate phosphate from its ore. Several hundred microorganisms (both bacteria and fungi) capable of solubilization of phosphate ore have been isolated from the environment. Work is ongoing to determine the mechanism for solubilization. In addition, how these organisms could be used in a bioprocess is being investigated.

Jan 1, 1989

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By Christof Metzger

This paper discusses the process utilized by the Kiewit?Bilfiger Berger Joint Venture (Contractor) to select, design, and procure the largest mixshield tunnel boring machine (TBM) ever implemented in North America. The mixshield will excavate the 8,534 linear m × 6.7 m ID (28,000 linear ft × 22 ft ID) tunnel for the City of Portland Oregon?s, Bureau of Environmental Services (Owner) East Side CSO Tunnel Project. TBM selection was conducted under a preconstruction contract in which the Contractor, Owner, Construction Management Consultant and Designer collaborated on TBM selection prior to commencement of construction. This paper focuses on TBM design considerations, including the use of one versus two machines, machine configuration,extended-wear protection, hyperbaric interventions, boulder digestion, and erection of a steel-fiber-reinforced segmental lining

By T. R. Ellis

Minerals Appraisers/Valuers often find great difficulty or failure in attempting to employ the Sales Comparison Approach to the Market Value Appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income producing property. Common criticisms of the sales comparison approach by minerals appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the Income Approach are usually derived by minerals appraisers, and by review of some conspicuous examples of the much too common misuse or abuse of the income approach in market value minerals appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables (see APPENDIX). The examples are used as the basis for discussion of ways to employ adjustments for operating economics and many other factors, while cautioning about the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011