Search Documents

By M. Batzle

The upper Arkansas basin has some of the greatest potential for geothermal development in Colorado. Over several summers, students conducted an investigation using seismic, gravity, and magnetics in order to help identify the large structures and basin fill associated with the Rio Grande Rift. Adjacent to Mount Princeton Hot Springs, near surface geophysics was conducted to help understand the faulting and fractures that act as a conduit for hydrothermal flow. The methods used included high frequency 3D seismic, magnetics, gravity, D.C. resistivity, and self potential. Throughout the Mount Princeton area, passive seismic, vertical seismic profiling, and well logging were also used to better understand the geology and activity of the region. The results indicate for the area northwest of the hot springs, a 40 to 50 m thick unconsolidated layer overlying the fractured granitic basement. The DC profile shows a deep geothermal anomaly of low resistivity which correlates with a positive SP anomaly in the same region. In the Chalk Creek valley, a shear zone extends from the north east to the south west, just south of the Chalk Cliffs. There appears to be an upward migration of the water through this shear zone which then flows along the porous sediments towards the south in this area. The deep seismic data collected in the center of the basin suggests that the depth to the basement is approximately 2000m. Also identified on the deep seismic are two major faults on the west end and two minors at the east end of the cross-section. An alteration zone is identified between the faults and a possible Precambrian northeast trending shear zone. The potential for developing an Enhanced Geothermal System (EGS) near the center of the valley is high. Our geophysical results indicate a deep basin fill near the center of the basin providing high temperatures. The range front (Sawatch) fault is observed to penetrate under the center of the basin and is an attractive target for natural fractures.

Jan 1, 2011

By C. P. Kelley, T. J. McKeon

Several recent developments in fine screening technology have been implemented at the DuPont Starke, Florida plant allowing enhanced zircon recoveries while minimizing operator requirements and total operational costs. The total design concept came about through the efforts of engineers at Derrick Corporation (Buffalo, New York), DuPont Titanium Technologies (Starke, Florida) and Roche Mining (Carrara, Australia). The use of the Kelsey Jigs for zircon recoveries from the tailings stream requires two wet sizing functions in order to operate properly. The first wet sizing is required on the initial mineral slurry feed to the Kelsey Jig. This sizing is intended to protect the Kelsey Jigs internal screen basket from plugging with nearsize particles, thereby keeping production rates maximized. The second sizing function is intended to recover properly sized garnet ragging material, which inadvertently ends up in the tailings stream leaving the Kelsey Jig. The unique machine design developed by the three partners in this project incorporated both wet sizing functions (protection and garnet recovery) into a single patented high capacity wet screening machine fitted with patented screen surface technology. This screen surface technology allowed for high capacity slurry handling capabilities at separations as fine as 230 microns while experiencing no nearsize blinding and extremely long screen panel life. The high open area urethane screen surfaces utilized in the application typically last 20 to 30 times longer than stainless steel wire surfaces. The stacked machine design minimized total equipment requirements and screen footprint requirements, and reduced power consumption and overall installation costs.

Jan 1, 2005

By J. Leinart

As is readily apparent, the reliability of the early-stage costs estimated for any mining project are critical to the viability of that project. An estimate too high might leave a potentially profitable deposit undeveloped or worse yet, available to a competitor. One too low might waste investment dollars in a project not yet economically ripe. There are two aspects critical to any estimate: 1. The cost data used to represent the values of the wages, salaries, supplies, and equipment. 2. The design used to determine the engineering parameters upon which the above estimated values are based. Given that all of the information contained in Mining Cost Service is provided by suppliers, equipment manufacturers and mine operators, one wonders why there is any question as to the reliability of cost estimates developed using this information. Given that it is all actual (as opposed to statistically derived) data, where do the problems with estimate reliability lie and what is the impact of the data on that reliability? The following presents a series of analyses designed to assess the reliability of the cost estimating process. Both the actual cost data and the engineering parameters upon which they are based are examined in an attempt to quantify and understand the importance of each. While several sources of cost information are available (Means, Richardson, Primedia?s Equipment Watch, and individual suppliers and manufacturers), the following rely solely on data contained in InfoMine USA, Inc?s, Mining Cost Service and in its Sherpa Mine Cost Estimating Software.

Feb 27, 2013

By R. A. Franks

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system?s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system?s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By David Dardick

Tround International Inc. is developing rock excavation and drilling devices which utilize a simple patented mechanism for firing frangible projectiles. This system launches a salvo of three projectiles with every shot in automatic sequence. Studies conducted by Physics International Inc. have demonstrated that firing projectiles into hard rock such as granite creates fragmentation which is much faster and cheaper than conventional drilling and blasting. The Tround salvo approach enhances this further by a controlled stresswave interaction created by a slight time difference during impact of the individual projectiles. The University of Maryland is conducting additional studies to optimize these parameters.

Jan 1, 1981

By Brian Garrod

Increasing use of pressurized-face tunnel boring machines in North America has produced a similar increase in the application of precast concrete tunnel linings. Where a pressurized TBM is needed, immediate ground support and ground water pressure resistance is also required. A segmental lining installed within the TBM tail shield provides the only available means of providing such a sealed lining. This paper addresses new developments in North America in lining applications and design. For the purposes of this paper, a precast concrete tunnel lining is defined as a tunnel lining constructed using precast concrete segments that are assembled into a lining ring. The lining rings are connected adjacent to each other to form a tunnel lining. Each segment has a sealing gasket around it so that when the lining is completed, it provides a fully waterproof lining system. The ring is erected within the tail shield of the TBM and the annular gap around the ring is filled with grout as the machine moves forward. The ring is not expanded and normally provides the finished lining of the tunnel with no requirement for a second pass lining. The TBM has a series of hydraulic rams that push on the leading edge of the segmental lining to provide the sole system of forward propulsion for the machine. The rings are tapered, being longer on one side than the other. This allows the rings to be installed either on a curve or in a straight line depending on the rotational position of the rings.

Jan 1, 2008

By A. Bascetin

Materials produced in quarries have been used for different intentions such as concrete and cement raw material, asphalt and embankment aggregates, railway ballast. Especially in cement manufacturing, the chemical composition and the uniformity of the raw materials play a strategic role in the economy and quality of the cement process. Therefore, it is necessary to achieve uniformity and desired chemical composition and maintain these at all production stages according to the type of cement produced. To achieve this goal the production planning and pit design play an essential role. This paper briefly outlines the production optimization of cement raw materials in a quarry in Istanbul western part of Turkey. For the purpose it was used the 3D ore body modeling and the geostatistical techniques. The variation of chemical components (%CaO, %Al2O3, %Fe2O3 etc.) and quality control parametres (LSF, SR, AR and etc.) obtained from the quarry were determined. Then the values of unknown chemical components and quality control parameters in the ore body were estimated using Kriging which is one of the geostatistical interpolation methods. The open pit design was also created by specifying wall slopes and taking into consideration of the grade distributions of the benches. The most important revolution in the paper is investigating the effects of the block dimensions in block modelling which is important for reserve estimation. The other important point in the study is using the different range values in variogram analysis for determination optimal reserve estimation. n this study, the effects of two parametres on reserve and waste amount estimation were determined according to CaO% distribution. The study was pointed out that the changing of the two parameters are very important for the optimal mine planning and environmental considerations.

Jan 1, 2010

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By B. Asbury, M. Cigla, C. Balci

The Western Mining Resource Center (WMRC) at the Colorado School of Mines (CSM) received a grant from the National Institute for Occupational Safety and Health (NIOSH) to perform a study that will help reduce the amount of respirable dust generated from the cutting of coal. The study is based upon laboratory testing and field experience. This information is being used to develop a new cutterhead design in conjunction with Joy Mining Machinery. The new cutterhead design is being evaluated with existing computer models developed at CSM. The new continuous miner cutterhead will be tested at the Twenty Mile Coal Company’s Foidal Creek Mine. Baseline testing with the current cutterhead will also be performed. This paper presents laboratory test results, design methodology, and test results performed to date.

Jan 1, 2002

By Jai Ghosh, Aprad E. Torma, Roger Guay

The catalytic effect of ferrous ion in the industrial biohydrometallurgical heap and dump leaching processes is explained. During the bacterial leaching of metal sulfides, ferric ion will partly be hydrolyzed and a variety of sols, gels, amorphous and/ or crystalline mono- and polynuc- lear hydroxo- and sulfato complex species formed, especially by olation and aggregation reactions. There are many problems associated with these iron precipitates especially in the purification of leach solutions. The present study will discuss the iron precipitation reactions; gives kinetic and thermodynamic evaluations of the effect of temperature on pyrite and ferrous iron oxidation; and reports on the tolerance of heavy metal ion concentrations by Thiobacillus ferrooxidans.

Jan 1, 1989

By T. Weatherwax

As part of a strategic research initiative at UBC to design and evaluate integrated underground mining and mineral processing systems, work has been done to determine how to utilize the coarse rejects of pre-concentration in the underground environment. An amenability study for nine orebodies from four of Xstrata Nickel?s Ontario operations evaluated both processing and waste disposal methods. The utilization of the rejects as a high quality backfill with minimal binder requirements has been identified as the preferred disposal method. Fill mixes utilizing the rejects in combination with classified tailings, full tailings, and cement were developed based on the geotechnical properties of the rejects. The mix designs were examined for both strength and rheological properties. The paper will present the results of the pre-concentration testwork, the design and strength testing of various mix designs for rejects from the nine ores and presents a conceptual design for an underground pre-concentration system based on this test work.

Jan 1, 2008

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By B. Barry, M. S. Klima

"Testing was conducted to evaluate the effects of hydroacoustic cavitation (HAC) treatment on two bituminous coal slurries and the subsequent separation of each slurry in a classifying hydrocyclone. HAC treatment was performed using a pilot-scale circuit fabricated by Furness-Newburge Inc. The circuit was designed to induce cavitation by means of flow through an ultrasonic resonator chamber or enhanced cavitation by initial flow through a cavitation chamber followed by flow through the ultrasonic chamber. The test materials were nominal -1,500-micron and -150-micron Illinois-basin bituminous coal slurries, which were obtained from an operating coal preparation facility. After 5 sec of HAC treatment, the median size of the -1,500-micron material was reduced, with ash values for certain size fractions decreasing more than 5 percent compared with untreated samples. Extending treatment time led to greater degradation of the +1,180-micron material and an increase in the -25-micron material, with ash reductions occurring for material in the -850+150-micron size range. Size degradation was less for the -150-micron material. Subsequent separation of the treated slurries was carried out in a hydrocyclone with diameter of 102 mm. HAC treatment led to a decrease in the ash value and an increase in the heating value of the underflow stream compared with the feed material. For example, the ash value was reduced by about 16 percent for the -1,500-micron material and 25 percent for the -150-micron material with heating value increases of 7 and 33 percent, respectively, after HAC treatment. Overall, HAC treatment appeared to have a slight effect on the size selectivity curves.IntroductionUltrasound in the range of 20 to 1,000 kHz, referred to as power ultrasound, consists of high energy waves that can create zones of compression and expansion when used to irradiate liquids (Frederick, 1965; Leighton, 1994; Mason and Lorimer, 1988). This action generates varying pressure regions leading to cavitation or the formation, growth and near-immediate collapse of microscopic voids or bubbles (Frederick 1965; Leighton 1994; Mason and Lorimer 1988). Collapse occurs when the bubble reaches critical size and cannot absorb additional sound field energy, and the critical size is governed by the ultrasound frequency (Shchukin et al., 2011)."

Jan 1, 2015

By W. S. Weldon, R. M. G. Machunter

The use of spiral separators for the beneficiation of fine coal typically in the size range - 2+0.lmm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimise metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Feb 24, 1997

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By Bill Cain, R. John Caulfield, D. Scott Kieffer

The East Bay Municipal Utility District is undertaking seismic upgrades of the Claremont Tunnel in the San Francisco Bay area. The tunnel carries treated water across the active Hayward Fault to supply a major metropolitan area. Studies indicate the tunnel could be severed by fault offset during a major seismic event. A design approach to achieve limited operation of the tunnel following fault displacement has been established and design details are currently being evaluated. This paper describes the project, the design approach, and summarizes significant construction constraints.

Jan 1, 2001

By Joseph M. McCann

The Brightwater regional wastewater treatment facility, under construction in King County, WA, includes an extensive conveyance system that will feature deep, soft-ground tunnels and shafts. Excavation of the Ballinger Way Receiving Portal to 65.8 m (216 ft) below grade through challenging geology was accomplished by means of artificial ground freezing. This paper discusses freeze design development, system installation and monitoring, and the contractual and construction challenges that were overcome, including work sequencing and excavation means and methods, together with lessons learned.

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By A. H. Sharbaugh

It is believed that considerable economic benefit would arise if run of mine (ROM) coal from the underground mines in the Winifrede seam could he enriched before shipment to the preparation plant by partial removal of the shale. Shale could comprise up to 50% of the ROM product. Complete mine-mouth separation is not necessary, but any process must be dry and have high Btu recovery. We have conducted a preliminary analysis of coal/shale mixtures from the Winifrede seam and we find that it is quite possible that a 50-50 ROM mixture of coal and shale could be converted to a 60-40 coal-shale mixture by inspection of individual lumps coming from the mine. The device would consist of a feeder/siever section to deliver the ROM coal > 5 cm (2 in) to an inspection station via a conveyor belt. This inspection station decides if a piece is coal or shale, and if it is shale, activates an air jet to blow shale off of the belt. We have evaluated a dielectric loss technique for the inspection device. The potential advantages of the dielectric loss method are high throughput, low capital cost, and no special handling or licenses would be required. Such a single lump inspection technique is made possible because of advances in high speed electronics and servo systems. This paper provides a summary of our analyses on the Winifrede coal sample, a description of a proposed apparatus to separate coal from shale, some of the experiments needed to demonstrate our ideas.

Jan 1, 1984