Search Documents

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

By S. Wakita, K. Aoki, Y. Mito, K. Date

It is of great importance to prevent a leakage of hazardous substances from underground storage plants, because this certainly leads to a fatal disaster for human societies. Therefore, effective grouting system needs to be developed, which can inject cement grout into low-permeable rock masses. Authors have carried out a series of laboratory injection tests using a fracture model and field tests in low-permeable rock masses. In these tests, not only was the superiority of dynamic grouting confirmed, but also the relationship between grouting-efficiency and injection parameters was investigated. In this paper, the results of laboratory injection tests and field tests together with theoretical approaches to them are mentioned. L’empêchement de la fuite des substances dangereuses des galeries de stockage est un traitement très important pour protéger la société humaine contre la comtamination catastrophique. Par conséquent, un procédé d’injection efficace doit être mis au point, qui peut injecter du coulis de ciment dans le rocher ayant une perméabilité basse. Les auteurs ont effectué une série d'essais d'injection en laboratoire en utilisant un modèle de rupture et d'essais sur le terrain dans le rocher ayant une perméabilité basse. Dans ces essais, était non seulement la supériorité du l’injection dynamique confirmée, mais aussi le rapport entre l’efficacité de l’injection et les paramètres d'injection a été étudié. Dans cet article, les résultats des essais d'injection en laboratoire et des essais sur le terrain ainsi que les méthodes théoriques pour les essais sont mentionnés. Es ist wichtig, Durchsickerns gefährlicher Substanzen aus unterirdischen Lagerstellen zu verhindern, weil dies für die menschliche Gesellschaft unter Umständen zu verheerenden Unfällen führen kann. Daher muß ein effizientes VerfugesSystem entwickelt werden, welches erlaubt den Mörtelschlamm in wenig durchlässige Felsenmassen einzuspritzen. Die Autoren haben eine Serie von Laboreinspritzungsversuchen mit einem Bruchmodell und Feldversuche an wenig durchlässigen Felsenmassen durchgeführt. Diese Versuche zeigten nicht nur die Überlegenheit des dynamischen Verfugens, sondern wurde dabei auch das Verhältnis zwischen Verfugen und Leistungsfähigkeit sowie den Einspritzungparametern untersucht. In dieser Studie werden die Ergebnisse der Laboreinspritzungtests und die Feldversuche zusammen mit den entsprechenden theoretischen Ansätzen erläutert.

Jan 1, 2003

By deur R. R. Mears

The expected curtailment of activities within the gold-mining industry by the closure of the more marginal mines, and the shortening of the life of the industry as a whole as a result of rising costs and/or an uncertain gold price, are factors that are bound to harm the South African economy in a number of ways. The industry has no option but to regard the gold price, which is determined on the world market, as a given quantity. The remaining ore reserves al tend to be of a lower grade and/or to be found at greater depth. Therefore tighter control of working costs would seem to be almost the only option open to the industry. Working costs can be divided into two broad categories: costs emanating from the environmental characteristics of the orebody, and costs emanating from the general inflationary environment in which the industry has to purchase its inputs. Working costs stemming from the physical environment also fall into two categories: those relating to the grade of the orebody, and those resulting from working at increasing depth and temperature, together with the need to pump increasing quantities of water. The industry is both capital- and labour-intensive in absolute terms, since it requires large inputs of labour as well as of capital. It is limited in its scope to adjust its production function by becoming more labour- or more capital intensive, and is dependent on a large labour force, which cannot easily be replaced by capital inputs. On the other hand, large amounts of capital are required for investment in shafts, development, machinery, and equipment. Since the early seventies, the working costs of the South African gold-mining industry have increased at an annual rate that was significantly higher than the general rate of inflation. This rapid rise in working costs has caused some mines to find themselves in a difficult profit position. At times, the gold-mining industry has even been compelled to restructure its cost/revenue relationship rather fundamentally by revising the grade of ore worked sharply upwards or downwards, as the case may be. The rise in the gold price since 1972 has made it possible for the industry to introduce significant changes in its Black wage policy. The main aim was to increase the permanency of the Black labour force and to encourage local Black workers to join the industry. At the same time, significant increases were also experienced in the cost of machinery and stores, as well as of capital, mainly as a result of inflation. In the study on which this paper is based, the author attempted to measure the influence of environmental factors on working costs, using the physical consumption of electricity as a criterion for measurement. He found that the usefulness of this criterion in relation to factors such as depth, temperature, and water quantities pumped was invariably more than neutralized by the effects of greater productivity and economies of scale. The effects of these environmental factors on the working costs of the industry could therefore not be determined to any degree of accuracy. It seems that good progress is being made with the development of capital-intensive forms of technology aimed at coping with rapidly rising working costs and other effects of increasing depth. Techniques are also being developed to improve rock-cutting procedures and to eliminate the use of explosives in order to introduce a continuous mining process. On the whole, the gold-mining industry seems to be more sensitive to general inflationary pressures than to the cost effects that are associated with depth, temperature, and water quantities pumped. Greater control is possible over physical environmental factors such as the grade of ore mined, temperature, rate and nature of development of a mine, and adaptation of the daily working cycle to a continuous mining process. Wolfe and others hold the view that the industry will lose control over labour costs as a result of the 'sharp increase in wages and the growth of Black trade unions. However, the use of more capital-intensive technology will allow the industry to reduce its labour force, and a smaller, better-trained, and more permanent labour force will enable the industry to cope with the increasingly difficult physical environment and higher wages.

Jan 1, 1987

By A. Ward, A. Smith, D. Harpley

Methods for the prediction of seepage quality from waste-disposal facilities are evaluated for input to the design of desalination treatment facilities. This is done by reference to a waste dump seeping into a near-surface aquifer, the contaminated seepage being collected by scavenger wells. As the quality of contaminated water intercepted by the wells will vary with both space and time, it is necessary for predictive methods to accommodate such variations. One-dimensional and two-dimensional predictive solute transport models are described and applied to the seepage and scavenger-well example mentioned above. The advantages and disadvantages, interims of overall applicability, data requirements, and possible accuracy, are described and discussed. While one-dimensional models have the advantages of speed, simplicity, and cost, the frequent requirement of prediction in both space and time necessitates more complex, two-dimensional simulation.

Jan 1, 1987

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By D. G. Krige

By use of models based on the South African gold-mining industry, analyses are made of the effects of changes in the mining tax structure on the .State's tax income from potential new mines; also on the percentage of such mines likely. to be proceeded with. The percentage is affected by the correlation between changes in taxation and in the flotation pay limits !or new mines. It is shown that the State stands to gain both directly and indirectly from raising the level of the capital allowance and from its extension to all mines; and that the reduced taxation resulting from a lowering of the discriminatory high tax formula for the gold mines, would, in respect of potential new mines, be compensated for by a significant increase in the percentage of such mines that would be proceeded with.

Jan 1, 1979

By A. J. Jager, J. A. Ryder, M. U. Ozbay

This paper deals with procedures used for designing pillar systems in hard-rock tabular mines operating at shallow depths, typically less than 1000 m. A comprehensive review if current practice identifies four types if pillars, namely non-yield, yield, crush and barrier pillars, and the main principles for designing these pillars are outlined. It is shown that the current design methods for pillar systems in South Africa are mainly empirical, each mine developing its pillar-design methods based largely on practical experience. This results in varying pillar layouts, even between neighbouring mines, despite similarities in geology, and depth if mining. It is suggested that some current layouts may fall short if being the best as regards safety, the maximum safe extraction percentages, or flexibility in accommodating future mining scenarios in deeper or otherwise different geological conditions.

Jan 1, 1995

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may 'poison' the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

The Registrar has requested us to publish the following notices: COUNCIL'S POLICY REGARDING LATE APPLICATIONS IN TERMS OF SECTION 18(4) (b) OF THE PROFESSIONAL ENGINEERS' ACT, 1968 (ACT NO. 81 OF 1968) Laat aansoeke om registrasie as Professionele Ingenieurs Die Suid-Afrikaanse Raad vir Professionele Ingenieurs (SARPI) vestig die aandag daarop dat daar 'n mistasting bestaan oor die vraag of 'n persoon sonder erkende ingenieurskwalifikasies wat nie in 1969 aansoek gedoen het om registrasie as professionele ingenieur nie, nie meer aansoek mag doen nie. Diegene wat voor 14 Februarie 1969 minstens 3 jaar aanvaarbare ingenieurswerk gedoen het kan nog oorweeg word. Die werk moet egter voldoen aan die standaarde deur SARPI neergele: dit Suid-Afrikaanse Road vir Professionele Ingenieurs DIE WET OP PROFESSIONELE INGENIEURS, 1968 (WET NO. 81 VAN 1968): JAARGELD: 1972/73 BOEKJAAR Kragtens die bepalings van Artikel 18(9) (b) van die Wet verval die Registrasie van 'n persoon wat as 'n ingenieur of ingenieur-in-opleiding geregistreer is as sodanige persoon versuim om die voorgeskrewe jaargeld binne ses maande nadat dit betaalbaar word, te betaal. Aandag word ook vriendelik daarop gevestig dat persone wat kragtens Artikel 18(4) (b) van die Wet geregistreer is (dit wil se persone wat nie oor 'n erkende akademiese kwalifikasie beskik nie) en wat toelaat dat hulle registrasie verval, moontlik nie weer vir registrasie in aanmerking sal kan kom nie. Vir persone in hierdie kategorie is dit dus van kardinale belang om toe te sien dat hulle jaargeld binne die voorgeskrewe tydperk betaal word.

By C. Clark, P. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, the National Institute for Occupational Safety and Health (NIOSH) at the Spokane Research Laboratory is developing, modifying, and testing equipment to replace the necessity of doing lifting tasks manually. To reduce single-event lift injuries, equipment having mechanical automatic weight sensing and balancing control was investigated. The Coleman manipulator was selected for testing. Modifications to the Coleman manipulator to make it more suitable for underground mine use included mobilization, self-containment, all-purpose gripper attachment, and support jacks. To reduce or eliminate the need to clean off manually the materials that commonly plug grizzly openings (timbers, wire mesh, roof bolts, and other debris), a track-guided pincher arm device was developed. The TGPA attaches to an impact hammer head, and the pincher arms are controlled by the operator of the hammer. Oversized rock can be broken with the pincher arms in the up position; the arms can then be lowered to grab and remove debris. Sweeping action to remove cohesive fines bridging grizzly openings is also greatly improved. This device is especially useful in recessed grizzlies. An industrial gun was tested to evaluate its effectiveness in breaking oversized rock. Boulders up to 76 cm in diameter were successfully broken to minus 33 cm. Although methods to control flyrock need to be developed, an industrial gun may be a safe and inexpensive alternative to breaking oversized rock in certain underground mining situations. Keywords: Mining, materials handling, over-exertion, injuries

Sep 1, 2001

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

By A. J. Jager, N. C. Joughin

The effects of extensive solid-waste packing as a support medium are described. It is shown that the waste packing resulted in excellent hangingwall conditions with only minor deleterious effects.

Jan 1, 1979

By R. C. Dunne, W. A. Gilbert, I. J. Corrans, K. S. Liddell

After bench-scale and pilot-plant tests in which it was shown that wet high-intensity magnetic separation (WHIMS) can achieve good recoveries of gold and uranium from Witwatersrand residues, a production size machine was installed at a gold mine. The mechanical and metallurgical performance of this machine have been satisfactory, and the economics of the process are attractive. WHIMS can be combined with other unit operations like flotation for the optimization of overall gold and uranium recoveries. This concept is shown to be relevant, not only to operations for the retreatment of tailings, but to processes for the treatment of coarser material. In the latter, there is a saving in energy consumption compared with the energy required for the fine grinding of the total feed, and a material suitable for underground backfill can be produced. Improved. more cost-effective WHIMS machines currently under development are also described.

Jan 1, 1983

By G. Peinaar

Superhardening is a new development by which a substantial increase in hardenability above the normal can be achieved in Iow-alloy steels. This paper concerns the reversible temper-embrittlement behaviour of steels with a superhardenability characteristic. Steels of type BS 530A40 with manganese modifications varying from 0,72 to 1,27 per cent in the superhardenable and conventional condition were compared. It was concluded that superhardenability in itself does not affect the susceptibility of a particular steel to temper embrittlement. However, an increase in manganese content, which was intended to increase the base hardenability of the steel, caused serious deterioration of the temper-embrittlement properties. As the use of manganese, chromium, and nickel to increase base hardenability results in an increase in susceptibility to temper embrittlement, it is suggested that this effect should be countered by the addition of 0,2 to 0,3 per cent molybdenum.

Jan 1, 1984

By M. Kirsten, W. H. Botha, M. H. Fox, J. A. Moolman, A. J. Lathwood

Water is a valuable and in many areas a scarce resource. Governmental legislation regulates the environmental impact of water usage and wastewater disposal through the issue of licenses. These requirements mean that hydrometallurgical refineries must ensure that water consumption and water disposal is managed on a continuous basis in order to prevent the repeal of their operating license. Water balances are often overlooked during the design of a hydrometallurgical refinery. Recent changes in environmental legislation have forced both design engineers and operational management to review water use and disposal within these processes. Unlike concentrators where water can easily be recovered by recycling from tailing dams, water introduced into hydrometallurgical refineries becomes contaminated with soluble metals and thus requires pre-treatment prior to disposal. This paper discusses the various concerns that need to be considered during design and operation of hydrometallurgical refineries with respect to the water balance.

Jan 1, 2007

By use of a finite-difference model of an experimental galvanic cell, the effect of a resistance in the metalic conduction path on the potential and current distributions in the cell was predicted. The model predictions were compared with experimental measurements of potential profiles (measured by use of a scanning reference electrode) and galvanic currents. The predictions agreed well with the experimental measurements. Apart from this model, which is applicable in macroscopic cells (Le. with an electrolyte of low conductivity), a calculation procedure was developed to predict the effect of an external resistance on the galvanic current in a microscopic cell (high conductivity). The responses of the galvanic currents in the microscopic and macroscopic cells to changes in the external resistance were compared. From the similarity of the responses, a simple practical procedure for the evaluation of the external resistance (meter resistance) that can be tolerated is proposed.

Jan 1, 1989

By J. M. Stewart

Although the incidence of heat stroke in South African gold mines is small, work continues on its reduction. This paper proposes limits of heat stress that are applicable to South African underground conditions, with the warning that they should not be extrapolated to other situations without careful consideration having first been given to their limitations. These limits of heat stress take physical and physiological considerations into account, and they correspond to there being a 10-6 risk of an essentially nude man developing a rectal temperature in excess of 40°C. It is recommended that further work should be undertaken on the development of equations for the calculation of the heat transfer from clothed men, the derivation of equations that quantify the physiological conductance and sweat rate response of humans, and on establishing the frequency distributions that describe variations in rectal temperature response between individuals in different types of environment.

Jan 1, 1981

By W. Spencer

An examination is made of quality standards in castings produced by the South African foundry industry, and some examples are given of the consequences of poor quality to the user. Corrective measures are suggested.

Jan 1, 1981

By B. Mienie, J. F. Morrison, C. H. Wyndham, M. J. Martinson, N. B. Strydom

Contribution to discussion M. J. Martinson (Associate Member)*: Application of the simple selection test mentioned in the penultimate paragraph of the paper (reference to a more detailed description of the test would not have been inappropriate) should assist South African mining engineers to make more efficient and possibly more humane use of available labour. The authors mention that the test 'is in use in the gold mining industry', and it would be interesting to know the extent of this usage in terms either of number of mines or as a percentage of the total number of labourers employed on 'heavy' tasks. The paper would have been of greater interest had the authors attempted to relate their findings to the statistics of labour usage in gold mines, members of the Chamber, and to the 'heavy' tasks in particular. On this the authors confine themselves in their Introduction to the somewhat ambiguous statement that 'A relatively high proportion of the 360,000 Bantu mine labourers are employed underground on manual tasks'. To appreciate the practical significance of the authors' work one needs a detailed breakdown of the underground labour force by occupations, together with estimates of quantities such as: (a) total stope and development tonnages moved manually per shift: by shovelling by shovel/tram by tramming together with distances and any other relevant data; (b) theoretical energy expenditures required to accomplish (a); (c) actual energy expenditures required to a accomplish (a); (d) energy theoretically available to accomplish (a) based on 50 per cent of the total maximum oxygen intakes of the labour force allocated to these tasks. Analyses of this sort on an industry basis might demarcate the more promising areas for detailed investigation. Stress is often laid on the need for increased mechanisation to increase stope productivity, but it may be questioned if enough is known about the characteristics, performance and potential of our underground labour force to warrant blind acceptance of stope mechanization as the industry's panacea. Provided that health and safety are not compromised, the ultimate yardstick for assessing any form of stoping is profitability; obviously the industry must investigate very thoroughly any form of mechanization which might reasonably be expected to increase profitability, but it should also be remembered that a radical overhaul of existing systems-which have after all evolved by trial and error over the past 75

Jan 11, 1968